FOLDING DOORS LE-LN-LG SLIDING DOORS SN SHUTTER DOORS BT TECHNICAL MANUAL

LEGEND CE MARKING CERTIFICATION DATA LE FOLDING DOOR without bottom rail LN FOLDING DOOR without bottom rail LG FOLDING DOOR with bottom rail page 02 page 03 page 10 page 17 page 32 SN - SLIDING DOOR Top hung page 53 Ground Supported page 64 BT - SWINGING DOOR page 71 OPTIONAL Windows page 77 Ventilation grille page 79 Wicket Door page 80 AUTOMATION SYSTEMS LE, LN Page 91 LG, SN Page 93 Motorization Kit Page 99 ISOTHERM thermal-break system page 104 Pag. 1 di 107

HORIZONTAL SECTIONS LEGEND VERTICAL SECTIONS L.F.M. : Width of the wall opening H.F.M. : Height of the wall opening L.PAS. : Width of net passage H.PAS. : Height of net passage L.FT. : Invoicing width H.FT. : Invoicing height FOLDING DOOR NOMENCLATURE LE folding door without bottom track, panels packed 90 or 180 1002S 2+0, one pack, two panels 1003S 3+0, one pack, three panels 2002S 1+1, two packs, two panels 2003S 2+1, two packs, three panels 2004S 2+2, two packs, four panels 2005S 3+2, two packs, five panels 2006S 3+3, two packs, six panels 2008S 4+4, two packs, eight panels LN folding door without bottom track, panels packed 90 or 180 1002MO 2+0, one pack, two panels, manual or motor operated 1003MA 3+0, one pack, three panels, manual operated 1004MO 4+0, one pack, four panels, manual or motor operated (only 90 ) 1004MA 4+0, one pack, four panels, manual operated (180 ) 2002MO 1+1, two packs, two panels, manual or motor operated 2003MO 2+1, two packs, three panels, manual or motor-operated 2004MO 2+2, two packs, four panels, manual or motor-operated 2005MA 3+2, two packs, five panels, manual operated 2006MA 3+3, two packs, six panels, manual operated 2006MO 4+2, two packs, six panels, manual or motor-operated (only 90 ) 2008MO 4+4, two packs, eight panels, manual or motor-operated (only 90 ) LG folding door with bottom track, manual or motor-operated, only 90 1003MOS 3+0, one pack, three panels 1004MOS 4+0, one pack, four panels 1005MOS 5+0, one pack, five panels 1006MOS 6+0, one pack, six panels 1008MOS 8+0, one pack, eight panels 2006MOS 3+3, two packs, six panels 2008MOS 4+4, two packs, eight panels SN sliding door, manual or motor-operated EK1000N one pack, top hung, without bottom track EK2000N two packs, top hung, without bottom track EK1000 one pack, top hung, with bottom track EK2000 two packs, top hung, with bottom track EK1000A one pack, ground supported, with bottom track EK2000A two packs, ground supported, with bottom track BT swinging door, manual operated US1 one leaf US2 two leaves Pag. 2 di 107

CE MARKING CRTIFICATION DATA The data in the following tables show the results of the tests performed at the ISTITUTO GIORDANO for the CE marking certification of doors, on the basis of regulatory standard UNI EN 13241-1 for industrial, commercial and garage doors and gates. MOTOR-OPERATED DOOR Resistance to water penetration a) door without bottom track Class 0 b) door with bottom track Class 2 Release of harmful substances Absent Wind load resistance Class 4*** Thermal transmittance (U) a) panel W/(m². K) 0.62 b) door * W/(m². K) 1.60 Soundproof * * 22dB Air permeability Class 0 Mechanical resistance Passed Operating forces Passed Durability 20,000 cycles Geometry comp. glass Passed Fire resistance B-S1,d0 MANUALLY OPERATED DOOR Resistance to water penetration a) door without bottom track Class 0 b) door with bottom track Class 2 Release of harmful substances Absent Wind load resistance Class 4 Thermal transmittance (U) a) panel W/(m². K) 0.62 b) door * W/(m².K) 1.60 Soundproof * * 22dB Air permeability Class 0 Operating forces Durability Geometry comp. glass Fire resistance Passed 20,000 cycles Passed B-S1,d0 * These values are calculated for a complete installed door of 4500x5000 (WxH) mm of 4 panels. * * Not certifiable *** Only for the LE model: class 3 up to 5000 Height, class 2 up to 6000 Height. Pag. 3 di 107

LE FOLDING DOOR WITHOUT BOTTOM RAIL: 2+2, 2+1, 2+0, 1+1, 3+0, 3+3, 3+2, 4+0, 4+2, 4+4 UNI EN 13241-1 A1:2011 CE CERTIFIED PRODUCT Folding industrial door consisting of self-supporting monobloc panels of variable dimensions (55mm thick), perimeter frame consisting of dovetail shaped profile made of 20/10 thick galvanised steel (open section for integral injection), double galvanized (Sendzimir treatment) and pre-coated steel sheet cladding (stucco embossed 5/10+5/10 thick) with protective film (to be removed within 15 days after installation), self-extinguishing Class B2 CFC-free polyurethane insulation injected using high pressure foaming cycle with a density of 40 kg/m³. Flat panel, vertical micro-ribbing, pitch 160 mm Exclusive hinges made of black painted galvanised steel, with ball bearings, positioned with concealed wings and fixed at the inner load-bearing frame by means of a contrast plate concealed in the gasket (patented system). The number of hinges varies according to door s dimensions. Fixing system by means of special slotted brackets (on the floor and on the top rail) which allow adjustment on three axes, to be fixed by means of bolts (not included in the supply). Air/water sealing system: - black EDPM anti-crush/anti-ageing gaskets between the door panels; - black EDPM anti-ageing gaskets between door panels and lintel; - black EDPM anti-ageing gaskets between door panels and side walls; - on the floor: easily replaceable black nylon brush, with adjustable support made of black pre-coated aluminium; for an ideal sealing against water seepage, a grille or duct on the inner floor is recommended (not included in the supply); Manual locking system by means of internal black lever handle locks with two locking points (top/bottom), galvanised steel rods with concealed guide latches (exclusive system), rod end and floor striker, both made of stainless steel. As an option, lever handle bolt with cylinder, key and external handle. Bottom locking ensured by black nylon striker to be fixed to the floor by means of bolts (not included in the supply); as an option, possibility of special striker to be recessed in the floor, with telescopic operation, to facilitate transit of vehicles (patented system). Movement system by means of top rail made of galvanised steel 35/10 thick with slots for fixing and adjustment, to be fixed on the wall by means of bolts (not included in the supply); sliding carriages with bearings and adjustable pins diam. 20 mm. Panels packed at 90 or 180 (optional). This model is designed for internal installation. - COLOURS AVAILABLE (similar to RAL) - Smooth plate: White RAL 9002, Red RAL 3000, Green RAL 6005, Blue RAL 5010, Grey RAL 9006, Dark Grey RAL 7016, Brown RAL 8019. - Stucco Embossed plate: White RAL 9002, Grey RAL 9006, Green RAL 6005. N.B.: for reveal fixed installation, provide infill of at least 110 mm for each side. N.B.: This model is advised for inside installation CE UNI EN 13241-1 A1:2011 MARKING DATA Product certification issued by Istituto Giordano Bellaria (RN). - Wind load resistance: Class 3 - Average thermal transmittance (U=W/m². K): 1.60 (door 2+2 without window, 25 m2) - Durability: 20,000 cycles - Average noise reduction: 22 db (not certifiable) - Fire resistance: B-S1, d0 Pag. 10 di 107

Warnings Dark colorations may give place to a temperature difference between inside and outside (on the side exposed to the sun) for more than 40 /45 degrees. This causes a door deformation which in case of a prolonged sun exposure may lead to a steel s breakaway from the insulating material; issue of physical-mechanical dilations and not of production defects. The producer, therefore, does not assume any responsibilities and does not recommend the use of dark colours on doors whose installation involves a prolonged sun exposure. OPTIONAL WICKET SWING DOOR - Without threshold, on 2+1, 2+2, 2+3, 4+2, 4+4 configuration (door height over H>3000 mm.) indoor installation; cut panel door leaf with upper rebated frame made of black aluminium profile, equipped with panic push-bar with two locking points panic bar (top/bottom) with cylinder and external handle. An exclusive system increases the stability to a considerable extent; the overhead striker makes the door solidly connected with the upper and side panels, a special bracket allows optimum abutting against the striker on the floor. NOTE.: the panic bar latch operates on the floor striker of the door, there is no need to apply a specific one. This door can be inserted only on the first panel of a pack with two, or four leaves - Without threshold, on 2+1, 2+2, 2+3, 4+2 configuration (door height over H>3000 mm.) outdoor installation Pedestrian door with black aluminium frame on two sides, without lower cross beam, fitted with panic push-bar with two locking points (top/bottom) with cylinder and external handle. This door can only be achieved for external industrial door opening and it must be placed: on the first panel of a pack with 2 panels - with threshold, height 90 mm. (net free passage max mm. 1000x2100): door frame made of black aluminium profile, can be painted as per request. One-point lock with cylinder and black handles; as an option, recessed triple lock or panic bar. This door can be inserted only on the first panel of a pack with two, or on the single one. WINDOW -Rubber: window frame made of black anti-ageing EPDM; cladding with 8/9 transparent stratified glass with rounded corners (radius 125 mm.). -Aluminium (thermal break): window frame made of black aluminium profile with 90 corners, can be painted as per request, cladding with 8/9 transparent stratified glass. NOTE: for constructional purposes, the distance between the windows must be at least 500 mm. VENTILATION GRILLE Made of silver or black aluminium, with fixed blades, can be painted as per request. Dimensions available (WxH): 600x300 mm. and 1000x600 mm. Possibility of rotation of pack of panels through 180 (optional). Only for: 2+0, 3+0, 2+1, 2+2, 3+2, 3+3. Pag. 11 di 107

SMART LE - FOLDING DOOR WITHOUT BOTTOM RAIL - G Mod. 1002S(2+0), 1003S(3+0),2002S(1+1), 2003S(2+1), 2004S(2+2), 2005S(3+2), 2006S(3+3)/(4+2), 2008S(4+4) Pag. 12 di 107

VERTICAL SECTIONS 1)FACE FIXED a) INSIDE rot. 90 DETAIL OF TOP RAIL LATERAL RAIL-PANEL CONNECTION CARRIAGE CONNECTION 130 130 H.F.M. = H.PAS. INTERNAL H.FT. INTERNAL DETAIL OF LOWER AREA LATERAL FIXING TO THE GROUND CENTRAL CLOSURE FLOOR STRIKER 40 40 DETAIL OF TOP RAIL 360 INTERNAL INTERNAL INTERNAL LATERAL RAIL-PANEL CONNECTION CARRIAGE CONNECTION INTERNAL The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 13 di 107

VERTICAL SECTIONS 1)FACE FIXED a) INSIDE rot. 90 LATERAL RAIL-PANEL CONNECTION DETAIL OF TOP RAIL CARRIAGE CONNECTION 40 INTERNAL COVER COVER H.PAS. H.F.M. = H.FT. INTERNAL DETAILOF LOWER AREA LATERAL FIXING TO THE GROUND CENTRAL CLOSURE INTERNAL 40 INTERNAL INTERNAL FLOOR STRIKER DETAIL OF TOP RAIL H.PAS. H.F.M. = H.FT. LATERAL RAIL-PANEL CONNECTION CARRIAGE CONNECTION COVER 360 INTERNAL The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 14 di 107

HORIZONTAL SECTIONS DIMENSIONS 1 LEAF FACE FIXED 90 AND 180 L.F.M.= L.PAS. Note: FOR A RIGHT DOOR WORKING THE MINIMUM SIDE SPACE MUST BE MM. 110 DIMENSIONS 2 LEAVES FACE FIXED 90 DIMENSIONS 2 LEAVES FACE FIXED 180 L.F.M.= L.PAS. L.F.M.= L.PAS. 100 300 250 250 110 L.F.M.= L.PAS. The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 15 di 107

DIMENSIONS 3 LEAVES FACE FIXED 90 DIMENSIONS 3 LEAVES FACE FIXED 180 350 420 L.F.M. DIMENSIONS 4 LEAVES FACE FIXED 90 450 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 16 di 107

LN FOLDING DOOR WITHOUT BOTTOM RAIL G UNI EN 13241-1 CE CERTIFIED PRODUCT Folding industrial door consisting of self-supporting monobloc panels of variable dimensions (55mm thick), perimeter frame consisting of dovetail shaped profile made of 20/10 thick galvanised steel (open section for integral injection), double galvanized (Sendzimir treatment) and pre-coated steel sheet cladding (stucco embossed 5/10+5/10 thick) with protective film (to be removed within 15 days after installation), self-extinguishing Class B2 CFC-free polyurethane insulation injected using high pressure foaming cycle with a density of 40 kg/m³. Exclusive hinges made of black painted galvanised steel, with ball bearings, positioned with concealed wings and fixed at the inner load-bearing frame by means of a contrast plate concealed in the gasket (patented system). The number of hinges varies according to the dimensions of the door. Fixing system by means of lateral guides made of 20/10 thick galvanised section fitted with slotted L-shaped brackets which allow adjustment on 3 axes, to be fixed to the wall by means of bolts (not included in the supply). Air/water sealing system: - black EDPM anti-crush/anti-ageing gaskets between the door panels; - black EDPM anti-ageing gaskets between door panels and lintel; - black EDPM anti-ageing gaskets between door panels and side walls; - on the floor: easily replaceable black nylon brush, with adjustable support made of black pre-coated aluminium; for an ideal sealing against water seepage, a grille or duct on the inner floor is recommended (not included in the supply); Manual locking system by means of internal black lever handle locks with two locking points (top/bottom), galvanised steel rods with concealed guide latches (exclusive system), rod end and floor striker both made of stainless steel. As an option, lever handle bolt with cylinder, key and external handle. Bottom locking ensured by black nylon striker to be fixed to the floor by means of bolts (not included in the supply); as an option, possibility of special striker to be recessed in the floor, with telescopic operation, to facilitate the vehicles transit (patented system). Movement system by means of top rail made of galvanised steel 35/10 thick with slots for fixing and adjustment, to be fixed to the wall by means of bolts (not included in the supply); sliding carriages with bearings and adjustable pins diam. 20 mm. Possibility of rotation of pack of panels through 90 to 180. - COLOURS AVAILABLE (similar to RAL) Flat panel, vertical micro-ribbing, pitch 160 mm - Smooth plate: White RAL 9002, Red RAL 3000, Green RAL 6005, Blue RAL 5010, Grey RAL 9006, Grey RAL 7016, Brown RAL 8019. - Stucco Embossed plate: White RAL 9002, Grey RAL 9006, Green RAL 6005. CE UNI EN 13241-1 A1:2011 MARKING DATA Product certification issued by Istituto Giordano Bellaria (RN). - Wind load resistance: Class 4 (kg. 100/m²., ca. 140Km/h) - Average thermal transmittance (U=W/m². K): 1.60 - Durability: 20,000 cycles - Average noise reduction: 22 db (not certifiable) - Fire resistance: B-S1, d0 Pag. 17 di 107

Warnings Dark colorations may give place to a temperature difference between inside and outside (on the side exposed to the sun) for more than 40 /45 degrees. This causes a door deformation which in case of a prolonged sun exposure may lead to a steel s breakaway from the insulating material; issue of physical-mechanical dilations and not of production defects. The producer, therefore, does not assume any responsibilities and does not recommend the use of dark colours on doors whose installation involves a prolonged sun exposure. OPTIONAL WICKET SWING DOOR - Without threshold, on 2+0, 2+1, 2+2, 3+2, 4+2, 4+0 configuration (door height over >3000 mm.): INDOOR INSTALLATION cut panel door leaf with rebated upper frame made of black aluminium profile, equipped with panic push-bar with two locking points panic bar (top/bottom) with cylinder and external handle. An exclusive system increases the stability to a considerable extent; the overhead striker makes the door solidly connected with the upper and side panels, a special bracket allows optimum abutting against the striker on the floor. Please, note.: the panic bar latch operates on the door s floor striker, there is no need to apply a specific one. This door can only be achieved for internal doors opening and its position must be: - On the first panel of a pack with 2 or 4 panels. - On the single panel; in this case the top panel lever handle lock will be located about mt.2,5 off the ground. - Without threshold on mod 2+0, 2+1, 2+2, 3+2, 4+2, 4+0 (with door height over H>3000 mm.). OUTDOOR INSTALLATION. Pedestrian door with black aluminium frame on two sides, without lower cross beam, fitted with panic push-bar with two locking points (top/bottom) with cylinder and external handle. This door can only be achieved for external industrial door opening and it must be placed: - on the first panel of a pack with 2 panels - with threshold, height 120 mm. (net free passage max mm. 1000x2100): surrounding frame made of black aluminium section, can be painted as per request. One-point lock with cylinder and black handles; as an option, recessed triple lock or panic bar. WINDOW - Rubber: surrounding frame made of black anti-ageing EPDM; cladding with 8/9 transparent stratified glass with rounded corners (radius 125 mm.). - Aluminium (thermal-break): surrounding frame made of black aluminium profile with 90 corners, cladding with double glazing or stratified glass up to 40 mm thickness. VENTILATION GRILLE Made of silver or black aluminium, with fixed blades, can be painted as per request. Dimensions available (WxH): 600x300 mm. and 1000x600 mm. Pag. 18 di 107

ISOTHERM: THERMAL-BREAK VERSION LN can also be constructed in ISOTHERM version, the solution for doors with high thermal insulation. The exclusive panel with a plastic frame (extruded Technopolymer EVICOM R450C) makes it possible to cut down heat dispersion (U=W/m². K) for more than 30%. Value measured on blank door 4500x4500H mm.: U=1.15. Maximum possible height 5000 mm. More details on page 101 AUTOMATION SYSTEM PAGES 87 Pag. 19 di 107

LIBER- LN FOLDING DOOR WITHOUT BOTTOM RAIL- G mod. 1002MO(90-180 )(2+0), 1003MA(90-180 )(3+0), 1004MO(90 )(4+0), 2002MO(1+1), 2003MO(90-180 )(2+1), 2004MO(90-180 )(2+2), 2005MA(90-180 )(3+2), 2005MO(90 )(4+1), 2006MA(90-180 )(3+3), 2006MO(90 )(4+2), 2008MO(90 )(4+4) Pag. 20 di 107

VERTICAL SECTIONS 1)FACE FIXED a)inside DETAIL OF TOP RAIL 450 H.F.M. = H.PASS. 40 INTERNAL H.FT. DETAIL OF LOWER LOCK INTERNAL INTERNAL FLOOR STRIKER DETAIL OF TOP RAIL H.FT. H.F.M. = H.PASS. 450 COVER INTERNAL The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 21 di 107

VERTICAL SECTIONS 1)REVEAL FIXED a) INSIDE DETAIL OF TOP RAIL H.PASS. H.F.M. = H.FT. 450 40 INTERNAL INTERNAL DETAIL OF LOWER LOCK FLOOR STRIKER H.PASS. H.F.M. = H.FT. DETAIL OF TOP RAIL 450 INTERNAL INTERNAL The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 22 di 107

LIBER- LN FOLDING DOOR WITHOUT BOTTOM RAIL Mod. 1004MO 180 (4+0), 2006MO 180 (4+2), 2008MO 180 (4+4) Pag. 23 di 107

VERTICAL SECTIONS 1)FACE FIXED a) INSIDE 560 H.F.M. = H.PAS. H.FT. 230 H.FT. H.F.M. = H.PAS. 40 INTERNAL INTERNAL INTERNAL FLOOR STRIKER b) OUTSIDE 230 600 COVER The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 24 di 107

VERTICAL SECTIONS 1)REVEAL FIXED a) INSIDE DETAIL OF TOP RAIL H.PAS. = H.F.M. - 200 H.FT. 200 200 TUBULAR INTERNAL TUBULAR DETAILOF BOTTOM RAIL INTERNAL INTERNAL FLOOR STRIKER b) OUTSIDE 600 200 40 H.FT. TUBULAR H.PAS. = H.F.M. - 200 COVER 200 DETAIL OF TOP RAIL 600 TUBULAR The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 25 di 107

HORIZONTAL SECTIONS - LEAVES PACK 90 DIMENSIONS 1 LEAF REVEAL FIXED DIMENSIONS 1 LEAF FACE FIXED 160 COVER OUTSIDE OUTSIDE 120 COVER INSIDE INSIDE DIMENSIONS 2 LEAVES REVEAL FIXED DIMENSIONS 2 LEAVES FACE FIXED 290 OUTDOOR COVER 280 OUTDOOR COVER INSIDE INSIDE The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 26 di 107

HORIZONTAL SECTIONS - LEAVES PACK 90 DIMENSIONS 3 LEAVES REVEAL FIXED DIMENSIONS 3 LEAVES FACE FIXED 390 COVER OUTSIDE 380 OUTSIDE COVER INSIDE INSIDE DIMENSIONS 4 LEAVES REVEAL FIXED DIMENSIONS 4 LEAVES FACE FIXED 490 OUTSIDE COVER 480 OUTSIDE COVER INSIDE INSIDE The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 27 di 107

HORIZONTAL SECTIONS - LEAVES PACK 180 DIMENSIONS 1 LEAF FACE FIXED OUTDISE DIMENSIONS 2 LEAVES FACE FIXED 120 120 OUTSIDE 120 375 175 275 INSIDE INSIDE DIMENSIONS 3 LEAVES FACE FIXED DIMENSIONS 4 LEAVES FACE FIXED OUTSIDE 120 OUTSIDE 475 INSIDE INSIDE RECEIVING JAMB REVEAL FIXED RECEIVING JAMB FACE FIXED OUTSIDE 120 OUTSIDE WITH SEAL 90 INSIDE INSIDE The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 28 di 107

LATERAL DIMENSIONS DIAGRAM - LEAVES PACK 90 X Y X 2+0 L.FT L.FT X = 290 mm Y = 120 mm X Y 2+1 L.FT X = 290 mm Y = 120 mm X Y 2+2 L.FT X = 290 mm X = 290 mm X Y 3+0 L.FT X = 390 mm Y = 120 mm X Y 3+1 L.FT X = 390 mm Y = 120 mm X Y 3+2 L.FT X = 390 mm Y = 290 mm X Y 3+3 L.FT X = 390 mm Y = 390 mm X Y 4+0 L.FT X = 490 mm Y = 120 mm X Y 4+2 L.FT X = 490 mm Y = 290 mm X Y 4+4 L.FT X = 490 mm Y = 490 mm The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 29 di 107

LATERAL DIMENSIONS DIAGRAM - LEAVES PACK 180 X Y X 2+0 X = 120 mm Y = 120 mm L.FT L.FT X Y 2+1 X = 120mm Y = 120 mm L.FT X Y 2+2 X = 120mm Y = 120 mm L.FT X Y 3+0 X = 120mm Y = 120 mm L.FT X Y 3+1 X = 120mm Y = 120 mm L.FT X Y 3+2 L.FT X = 120mm Y = 120 mm X Y 3+3 L.FT X = 120mm Y = 120 mm The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 30 di 107

LATERAL DIMENSIONS DIAGRAM - LEAVES PACK 180 NOTE: INCLINED TOP RAIL X Y 4+0 L.FT X = 120mm Y = 120 mm X Y 4+2 L.FT X = 120mm Y = 120 mm X Y 4+4 L.FT X = 120mm Y = 120 mm The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 31 di 107

LG FOLDING DOOR WITH BOTTOM RAIL G/2C250 UNI EN 13241-1 A1:2011 CE CERTIFIED PRODUCT Folding industrial door consisting of self-supporting monobloc panels of variable dimensions (55mm thick), perimeter frame consisting of dovetail shaped profile made of 20/10 thick galvanised steel (open section for integral injection), double galvanized (Sendzimir treatment) and pre-coated steel sheet cladding (stucco embossed 5/10+5/10 thick) with protective film (to be removed within 15 days after installation), self-extinguishing Class B2 CFC-free polyurethane insulation injected using high pressure foaming cycle with a density of 40 kg/m³. Exclusive hinges made of black painted galvanised steel, with ball bearings, positioned with concealed wings and fixed at the inner load-bearing frame by means of a contrast plate concealed in the gasket (patented system). The number of hinges varies according to door dimensions. Movement system by means of top rail made of 35/10 thick galvanised steel, complete with panels pack derailing device, provided with slotted brackets which allow adjustment on 3 axes, to be fixed on the wall by means of bolts (not included in the supply); sliding carriages with bearings and adjustable pins diam. 20 mm. The rail has provision for automation with chain drive. Dimensions (height): - mm. : doors with dimensions up to 30m² for each pack (G) - mm. 250: doors with dimensions more than 30m² for each pack (2C250) Bottom rail made of 25/10 thick galvanised section and pins with adjustable roller made of galvanised steel diam. 20 mm with self-lubricating, adjustable, replaceable Teflon bushes. Air/water sealing system: - black EDPM anti-crush/anti-ageing gaskets between panels; - nylon brush between panels and upper lintel; - black EDPM anti-ageing gaskets between first/last panels and side wall; - on the floor: easy-to-replace bottom nylon brush, with adjustable black pre-coated aluminium support profile. Manual locking system by means of black coloured internal lever handle bolt, two-point lock (top/bottom), galvanised steel rods with concealed guide latches (exclusive system); as an option it is possible to have lever handle bolt with cylinder, key and external handle. - COLOURS AVAILABLE (similar to RAL) Flat panel, vertical micro-ribbing, pitch 160 mm - Smooth plate: White RAL 9002, Red RAL 3000, Green RAL 6005, Blue RAL 5010, Grey RAL 9006, Grey RAL 7016, Brown RAL 8019. - Stucco Embossed plate: White RAL 9002, Grey RAL 9006, Green RAL 6005 CE UNI EN 13241-1 A1:2011 MARKING DATA Product certification issued by Istituto Giordano Bellaria (RN). - Wind load resistance: Class 4 (kg. 100/m²., ca. 140Km/h) - Average thermal transmittance (U=W/m². K): 1.60 - Durability: 20,000 cycles - Average noise reduction: 22 db (not certifiable) - Fire resistance: B-S1, d0 Pag. 32 di 107

Warnings Dark colorations may give place to a temperature difference between inside and outside (on the side exposed to the sun) for more than 40 /45 degrees. This causes a door deformation which in case of a prolonged sun exposure may lead to a steel s breakaway from the insulating material; issue of physical-mechanical dilations and not of production defects. The producer, therefore, does not assume any responsibilities and does not recommend the use of dark colours on doors whose installation involves a prolonged sun exposure. OPTIONAL WICKET SWING DOOR - with threshold, height 120 mm. (net free passage max mm. 1000x2100): door frame made of black aluminium section, can be painted as per request. One-point lock with cylinder and black handles; as an option, recessed triple lock or panic bar (only on first panel). - without threshold, (door height over H>3000 mm.): - aluminium door frame without threshold; door equipped with panic push-bar with two lateral locking points, with cylinder and external handle (only on first panel). WINDOW -Rubber: surrounding frame made of black anti-ageing EPDM; cladding with 8/9 transparent stratified glass with rounded corners (radius 125 mm.). -Aluminium (thermal-break): surrounding frame made of black aluminium profile with 90 corners, can be painted as per request, cladding with 8/9 transparent stratified glass. NOTE: for constructional purposes, distance between the windows must be at least 500 mm. VENTILATION GRILLE Made of silver or black aluminium, with fixed blades, can be painted as per request. Dimensions available (WxH): 600x300 mm. and 1000x600 mm. ISOTHERM: THERMAL-BREAK VERSION LG can also be constructed in ISOTHERM version, the solution for doors with high thermal insulation. The exclusive panel with plastic frame (extruded Technopolymer EVICOM R450C) makes it possible to cut down heat dispersion (U=W/m². K) for more than 30%. Value measured on blank door 4500x4500H mm.: U=1.15. Maximum possible height 5000 mm. More details on page 101 AUTOMATION SYSTEM PAGES. 87 Pag. 33 di 107

LIBRUM LG - FOLDING DOOR WITH BOTTOM RAIL-G Mod. 1003MOS(3+0), 1004MOS(4+0), 1005MOS(5+0), 1006MOS(6+0), 1008MOS(8+0) 2006MOS(3+3), 2008MOS(4+4), 2010MOS(5+5), 2012MOS(6+6) DOORS UP TO 30sqm PER LEAVES-PACK HEAVY-DUTY DRIVE UNIT The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 34 di 107

VERTICAL SECTIONS 1) FACE FIXED - INSIDE INSTALLATION DETAIL OF TOP RAIL 160 CHAIN (if motor-operated) H.F.M. = H. PAS. H.FT INTERNAL 160 max 1400 DERAILING DEVICE DETAIL OF BOTTOM RAIL QPF 40 QPF 55 120 50 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 35 di 107

VERTICAL SECTIONS 1) FACE FIXED - OUTSIDE INSTALLATION COVER RAIL It does not cover the derailleur 200 CHAIN (if motor-operated) DETAIL OF TOP RAIL 350 200 INTERNAL max 1400 H.FT H.F.M. = H. PAS. DETAIL OF BOTTOM RAIL QPF QPF 40 55 DERAILING DEVICE 50 120 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 36 di 107

VERTICAL SECTIONS 3) REVEAL FIXED WITH TUBULAR ELEMENT DETAIL OF TOP RAIL WITH TUBULAR ELEMENTS 160 (if motor-operated) H. PAS. DERAILING DEVICE DETAIL OF BOTTOM RAIL QPF 4)REVEAL FIXED TO THE CEILING 40 QPF 180 120 DETAIL OF TOP RAIL FIXED ON CEILING H. PAS. 55 50 QPF The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 37 di 107

VERTICAL SECTIONS 5)REVEAL FIXED WITH TUBULAR ELEMENTS DETAIL OF TOP RAIL WITH TUBULAR ELEMENTS DETAIL OF BOTTOM RAIL 6) REVEAL FIXED TO THE CEILING QPF 40 180 120 DETAIL OF TOP RAIL FIXED ON THE CEILING H. PAS. 160 does not cover the derailleur INTERNAL H. PAS. QPF INTERNAL 55 does not cover the derailleur 50 QPF The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 38 di 107

HORIZONTAL SECTIONS DIMENSIONS 3 LEAVES FACE FIXED OUTSIDE 660 DIMENSIONS 3 LEAVES REVEAL FIXED 660 OUTSIDE SIDE FIX PANEL COVERING THE LEAVES-PACK ENGINE ENGINE INSIDE INSIDE DIMENSIONS 4 LEAVES FACE FIXED DIMENSIONS 4 LEAVES REVEAL FIXED OUTSIDE 660 660 OUTSIDE SIDE FIX PANEL COVERING THE LEAVES-PACK ENGINE ENGINE INSIDE INSIDE The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 39 di 107

DIMENSIONS 5 LEAVES FACE FIXED DIMENSIONS 5 LEAVES REVEAL FIXED 860 OUTSIDE 860 OUTSIDE SIDE FIX PANEL COVERING THE LEAVES-PACK ENGINE ENGINE INSIDE INSIDE DIMENSIONS 6 LEAVES FACE FIXED 860 OUTSIDE DIMENSIONS 6 LEAVES REVEAL FIXED 860 OUTSIDE SIDE FIX PANEL COVERING THE LEAVES-PACK ENGINE ENGINE INSIDE INSIDE The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 40 di 107

DETAIL OF TOP RAIL Z B L.F.M. A X L. RAIL MOTOR POSITIONED IN SIDE "A" (opening side) N ANTE X (mm) 3 660 4 660 5 860 6 860 Z (mm) MOTOR POSITIONED IN SIDE "B" (closure side) N ANTE 3 4 5 6 X (mm) 460 460 660 660 Z (mm) 450 450 450 450 NOTE: MOTOR SIZE mm. 200 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 41 di 107

LEAVES COMPOSITION DIAGRAM (with motor placed on the back) X L.FT 3+0 X = 660 mm ( 460+200 engini ) X L.FT 4+0 X = 660 mm ( 460+200 engine ) X L.FT 5+0 X = 860 mm ( 660+200 engine ) X L.FT 6+0 X = 860 mm ( 660+200 motore ) The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 42 di 107

LIBRUM LG - FOLDING DOOR WITH BOTTOM RAIL - 2C250 Mod. 1005MOS(5+0), 1006MOS(6+0), 2006MOS(3+3), 2008MOS(4+4), 2010MOS(5+5), 2012MOS(6+6) DOORS OVER 30sqm PER LEAVES-PACK HEAVY-DUTY DRIVE UNIT The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 43 di 107

VERTICAL SECTIONS 1) FACE FIXED - INSIDE INSTALLATION DETAIL OF TOP RAIL CHAIN (if motor-operated) 300 DERAILING DEVICE DETAIL OF BOTTOM RAIL QPF 55 40 120 50 MOTOR-OPERATED TOP RAIL : MOTOR DETAIL max 500 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 44 di 107

PARTICOLARE 1) FACE FIXED - OUTSIDE INSTALLATION COVER VERTICAL SECTIONS GUIDA INFERIOREPARTICOLARE GUIDA INFERIOREPARTICOLARE GUIDA INFERIOREPARTICOLARE GUIDA COVER (not covering the front derailleur) DETAIL OF TOP RAIL CHAIN (if motor-operated) 300 DERAILING DEVICE INFERIOREPARTICOLARE GUIDA INFEERIOREPARTICOLARE GUIDA INFERIORE DETAIL OF BOTTOM RAIL QPF 55 40 50 120 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 45 di 107

VERTICAL SECTIONS 1) REVEAL FIXED TO THE CEILING - OUTSIDE INSTALLATION DETAIL OF TOP RAIL REVEAL FIXED TO THE CEILING COVER COVER (does not cover the derailleur) CHAIN (if motor-operated) 240 DERAILING DEVICE DETAIL OF BOTTOM RAIL 2) REVEAL FIXED WITH TUBULAR ELEMENTS - OUTSIDE INSTALLATION QPF 55 COVER 50 120 DETAIL OF TOP RAIL REVEAL FIXED WITH TUBULAR ELEMEMTS CHAIN (if motor-operated) DERAILING DEVICE The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 46 di 107

SEZIONI VERTICALI 1) REVEAL FIXED TO THE CEILING DETAIL OF TOP RAIL REVEAL FIXED TO THE CEILING COVER COVER (does not cover the derailleur) CHAIN (if motor-operated) 240 DERAILING DEVICE DETAIL OF BOTTOM RAIL 2) REVEAL FIXED WITH TUBULAR ELEMENTS QPF 55 COVER 50 120 DETAIL OF TOP RAIL REVEAL FIXED WITH TUBULAR ELEMEMTS CHAIN (if motor-operated) DERAILING DEVICE The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 47 di 107

HORIZONTAL SECTIONS DIMENSIONS 3 LEAVES FACE FIXED 660 DIMENSIONS 3 LEAVES REVEAL FIXED 660 SIDE FIX PANEL COVERING THE LEAVES-PACK ENGINE ENGINE DIMENSIONS 4 LEAVES FACE FIXED 660 DIMENSIONS 4 LEAVES REVEAL FIXED 660 SIDE FIX PANEL COVERING THE LEAVES-PACK ENGINE ENGINE The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 48 di 107

DIMENSIONS 5 LEAVES FACE FIXED DIMENSIONS 5 LEAVES REVEAL FIXED 860 860 SIDE FIX PANEL COVERING THE LEAVES-PACK ENGINE ENGINE DIMENSIONS 6 LEAVES FACE FIXED 860 DIMENSIONS 6 LEAVES REVEAL FIXED 860 SIDE FIX PANEL COVERING THE LEAVES-PACK ENGINE ENGINE The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 49 di 107

DIMENSIONS 8 LEAVES FACE FIXED 1060 DIMENSIONS 8 LEAVES REVEAL FIXED 1060 SIDE FIX PANEL COVERING THE LEAVES - PACK ENGINE ENGINE DETAIL OF OVERLAPS AT THE TOP OF THE RAIL AND DOOR DETAIL OF TOP STRIKER REVEAL FIXED DOOR COMPLETELY CLOSED 65 RAIL OVERLAP DOOR NOT CLOSED 35 50 LEAVES OVERLAP 18 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 50 di 107

DETAIL TOP RAIL FOR DOOR WITH LEAVES PACK TO ONE SIDE X L.F.M. Y A B L.G. MINIMUM SPACE NECESSARY FOR PANELS PACK AND MOTOR IN DIFFERENT COMBINATIONS MOTOR POSITIONED IN SIDE "A" (at the end) MOTOR POSITIONED IN SIDE "B" (at the beginning) N ANTE X (mm) Y (mm) N ANTE X (mm) Y (mm) 3 660 4 5 6 660 860 860 8 1060 10 1260 12 1460 3 4 5 6 8 10 12 460 350 460 350 660 350 660 350 860 350 1060 350 1260 350 NOTE : IN CASE OF MANUALLY OPERATED DOOR, IT IS ADVISABLE TO CONSIDER DIMENSIONS "X" AND "Y" INCLUDING THE MOTOR AS THE MINIMUM LATERAL SPACE. IF THIS IS NOT THE CASE, THE POSSIBILITY OF MOTOR-OPERATING THE DOOR MAY BE IMPAIRED. NOTE: MOTOR SIZE mm. 200 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 51 di 107

DETAIL OF TOP RAIL FOR DOOR WITH LEAVES PACK TO BOTH SIDES X L.F.M. Y A B L.G. MINIMUM LATERAL SPACES NECESSARY FOR LEAVES PACK AND MOTORS LEAVES PACK DIMENSIONS DIMENSIONSOF SADE RAILS + MOTORS N LEAF X (mm) Y (mm) N ANTE X + A (mm) Y + B (mm) 3 + 3 4 + 4 5 + 5 6 + 6 460 460 660 660 460 460 660 660 8 + 8 860 860 10 + 10 1060 1060 12 + 12 1260 1260 3 + 3 660 4 + 4 660 5 + 5 860 6 + 6 860 8 + 8 1060 10 + 10 1260 12 + 12 1460 660 660 860 860 1060 1260 1460 N.OTE: IN CASE OF MANUALLY OPERATED DOOR, IT IS ADVISABLE TO CONSIDER DIMENSIONS "X" AND "Y" INCLUDING THE MOTOR AS THE MINIMUM LATERAL SPACES. IF THIS IS NOT THE CASE, THE POSSIBILITY OF MOTOR-OPERATING THE DOOR MAY BE IMPAIRED. NOTE: MOTOR SIZE mm. 200 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 52 di 107

SN TOP HUNG SLIDING DOOR G UNI EN 13241-1 A1:2011 CE CERTIFIED PRODUCT Top-hung sliding industrial door consisting of self-supporting monobloc panels of variable dimensions (55mm thick), perimeter frame consisting of dovetail shaped profile made of 20/10 thick galvanised steel (open section for integral injection), double galvanized (Sendzimir treatment) and pre-coated steel sheet cladding (stucco embossed 5/10+5/10 thick) with protective film (to be removed within 15 days after installation), self-extinguishing Class B2 CFC-free polyurethane insulation injected using high pressure foaming cycle with a density of 40 kg/m³. Door panels joined by means of black painted hinges fixed in the load-bearing frame by means of contrast plates perfectly concealed in the gaskets. Movement system by means of top track made of 35/10 thick galvanised steel with slots for fixing and adjustment, to be fixed on the wall by means of bolts (not included in the supply); adjustable sliding carriages with ball bearings. The door is prepared for a drive unit with chain traction. 1) Version with bottom rail: rail made of 25/10 thick galvanised steel section, pins with galvanised steel sliding rollers diam. 20 mm. with self-lubricating, adjustable and replaceable teflon bushes. 2) Version without bottom rail: sliding rollers on the side of the opening and intermediate nylon holders to be fixed to the floor (for an optimal sealing against water seepage, it is advisable to fit a grille or duct on the inner floor, which is not included in the supply). Air/water sealing system: - black EDPM anti-ageing gaskets between the door panels; - on the floor, easy-to- replace nylon bottom brush, with adjustable supporting section made of black precoated aluminium; - black EDPM anti-ageing gaskets between door panels and lintel; - special aluminium section complete with easy-to- replace nylon brush, between door panel and side wall. Manual locking system by means of internal lever handle bolts with two locking points (top/bottom), galvanised steel rods with concealed guide latches (exclusive system); as an option, it is possible to have lever handle bolt with cylinder, key and external handle. - COLOURS AVAILABLE (similar to RAL) Flat panel, vertical micro-ribbing, pitch 160 mm - Smooth plate: White RAL 9002, Red RAL 3000, Green RAL 6005, Blue RAL 5010, Grey RAL 9006, Grey RAL 7016, Brown RAL 8019. - Stucco Embossed plate: White RAL 9002, Grey RAL 9006, Green RAL 6005. CE UNI EN 13241-1 A1:2011 MARKING DATA Product certification issued by Istituto Giordano Bellaria (RN). - Wind load resistance: Class 4 (kg. 100/mq., ca. 140Km/h) - Average thermal transmittance (U=W/m². K): 1.60 - Durability: 20,000 cycles - Average noise reduction: 22 db (not certifiable) - Fire resistance: B-S1, d0 Pag. 53 di 107

Warnings Dark colorations may give place to a temperature difference between inside and outside (on the side exposed to the sun) for more than 40 /45 degrees. This causes a door deformation which in case of a prolonged sun exposure may lead to a steel s breakaway from the insulating material; issue of physical-mechanical dilations and not of production defects. The producer, therefore, does not assume any responsibilities and does not recommend the use of dark colours on doors whose installation involves a prolonged sun exposure. OPTIONAL WICKET SWING DOOR - Without threshold (Minimum size for each pack Height over H>3000mm. and Width>2500mm.): cut panel door leaf with rebated upper frame made of black aluminium profile, equipped with panic push-bar with two locking points (top/bottom) with rod and external handle. This door can be located on every panel of one or two pack doors, excluding lateral panels - with threshold, height 120 mm. (net free passage max mm. 1000x2100) ) with bottom rail - with lower cross-beam height mm (net free passage mm. 1000x2100) without bottom rail Surrounding frame made of black aluminum section, painted as per request. One-point lock with cylinder and black handles; on request triple recessed lock or panic push-bar. It can be located in all door s panels. WINDOW -Rubber: surrounding frame made of black anti-ageing EPDM; cladding with 8/9 transparent stratified glass with rounded corners (radius 125 mm.). -Aluminium (thermal-break): surrounding frame made of black aluminium profile with 90 corners, cladding with double glazing or stratified glass up to 40 mm thickness. VENTILATION GRILLE Made of silver or black aluminium, with fixed blades, can be painted as per request. 60% ventilation. Dimensions available (WxH): 600x300 mm. and 1000x600 mm. ISOTHERM: THERMAL-BREAK VERSION SN can also be constructed in ISOTHERM version, the solution for doors with high thermal insulation. The exclusive panel with plastic frame (extruded Technopolymer EVICOM R450C) makes it possible to cut down heat dispersion (U=W/m². K) for more than 30%. Value measured on blank door 4500x4500H mm.: U=1.15. Maximum possible height 5000 mm. More details on page 101 AUTOMATION SYSTEMS PAGES 87 Pag. 54 di 107

FLUX SN - TOP HUNG SLIDING DOOR - G Mod. EK1000, EK2000 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 55 di 107

1) FACE FIXED WITH THE BOTTOM RAIL - INSIDE DETAIL OF TOP RAIL - MANUAL 210 H.F.M = H.PAS H.F.T. DETAIL OF TOP RAIL - MOTOR OPERATED 210 CHAIN 110 Horizontal section - 1 PACK L.F.M = L.PAS DETAIL OF BOTTOM RAIL 75 L.FT 75 Horizontal section - 2 PACKS 195 L.F.M = L.PAS 35 75 75 L.FT 55 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. 50 Pag. 56 di 107

1) FACE FIXED WITH THE BOTTOM RAIL - OUTSIDE DETAIL OF TOP RAIL - MANUAL 230 H.F.T COVER 110 H.F.M. = H. PASS DETAIL OF TOP RAIL - MOTOR OPERATED CHAIN 230 COVER 110 Horizontal section - 1 PACK 75 L.FT 75 DETAIL OF BOTTOM RAIL L.F.M = L.PAS. 85 Horizontal section - 2 PACKS 35 L.FT 75 75 L.F.M = L.PAS. 55 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. 50 Pag. 57 di 107

1) REVEAL FIXED WITH THE BOTTOM RAIL - INSIDE DETAIL OF TOP RAIL - MANUAL H.PAS. H.F.M. = H.F.T. COVER DETAIL OF TOP RAIL - MOTOR OPERATED Horizontal section - 1 PACK CHAIN COVER L.F.M = L.PAS. DETAIL OF BOTTOM RAIL 75 L.FT 75 Horizontal section - 2 PACKS 195 L.F.M = L.PAS. 35 75 75 L.FT 55 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. 50 Pag. 58 di 107

1) REVEAL FIXED WITH THE BOTTOM RAIL - OUTSIDE DETAIL OF TOP RAIL - MANUAL H.F.M. = H.F.T. COVER H. PAS. DETAIL OF TOP RAIL - MOTOR OPERATED COVER CHAIN Horizontal section - 1 PACK 75 L.FT 75 DETAIL OF BOTTOM RAIL L.F.M = L.PAS. 85 Horizontal section - 2 PACKS 35 L.FT 75 75 L.F.M = L.PAS. 55 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. 50 Pag. 59 di 107

1) FACE FIXED WITHOUT THE BOTTOM RAIL - INSIDE DETAIL OF TOP RAIL - MANUAL 210 H.F.M. = H. PAS. H.FT 210 CHAIN 110 L.F.M = L.PAS. 75 L.FT 75 135 L.F.M = L.PAS. 35 DETAIL OF TOP RAIL - MOTOR OPERATED Horizontal section - 1 PACK DETAIL OF BOTTOM RAIL Horizontal section - 2 PACKS 75 75 L.FT The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 60 di 107

1) FACE FIXED WITHOUT THE BOTTOM RAIL - OUTSIDE DETAIL OF TOP RAIL - MANUAL 230 COVER 110 H.F.T. H.F.M. = H. PAS. DETAIL OF TOP RAIL - MOTOR OPERATED 230 CHAIN COVER 110 Horizontal section - 1 PACK 75 L.FT 75 DETAIL OF BOTTOM RAIL L.F.M = L.PAS. 135 Horizontal section - 2 PACKS L.FT 75 75 35 L.F.M = L.PAS. The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 61 di 107

1) REVEAL FIXED WITHOUT THE BOTTOM RAIL - INSIDE VIEW DETAIL OF TOP RAIL - MANUAL L.F.M = L.PAS. 75 H. PAS. L.FT 75 L.F.M = L.PAS. 35 COVER H.F.M. = H.FT DETAIL OF TOP RAIL - MOTOR OPERATED CHAIN COVER Horizontal section - 1 PACK DETAIL OF BOTTOM RAIL 135 Horizontal section - 2 PACKS 75 75 L.FT The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 62 di 107

1) REVEAL FIXED WITHOUT THE BOTTOM RAIL - OUTSIDE VIEW DETAIL OF TOP RAIL - MANUAL H.F.M. = H.F.T. COVER H. PAS. DETAIL OF TOP RAIL - MOTOR OPERATED COVER CHAIN Horizontal section - 1 PACK 75 L.FT 75 DETAIL OF BOTTOM RAIL L.F.M = L.PAS. 135 Horizontal section - 2 PACKS L.FT 75 75 35 L.F.M = L.PAS. The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 63 di 107

SN GROUND SUPPORTED SLIDING DOOR G UNI EN 13241-1 A1:2011 CE CERTIFIED PRODUCT Ground supported sliding industrial door consisting of self-supporting monobloc panels of variable dimensions (55mm thick), perimeter frame consisting of dovetail shaped profile made of 20/10 thick galvanised steel (open section for integral injection), double galvanized (Sendzimir treatment) and pre-coated steel double sheet cladding (stucco embossed 5/10+5/10 thick) with protective film (to be removed within 15 days after installation), self-extinguishing Class B2 CFC-free polyurethane insulation injected using high pressure foaming cycle with a density of 40 kg/m³. Door panels joined by means of black painted hinges fixed in the load-bearing frame by means of contrast plates perfectly concealed in the gaskets. Movement system by means of top rail made of 35/10 thick galvanised steel with slots for fixing and adjustment, to be fixed on the wall by means of bolts (not included in the supply); sliding rollers with bearings and adjustable pins. The rail is provided with a special anti-derailing system. Bottom rail made of 30/10 thick galvanised steel section, provided in the brickwork, on which wheels with bearings ( U -shaped groove) run. The door is prepared for a drive unit with chain traction. Air/water sealing system: - black EDPM anti-ageing gaskets between the door panels; - on the floor, easy-to- replace nylon bottom brush, with adjustable supporting section made of black precoated aluminium; - black EDPM anti-ageing gaskets between door panels and lintel; - special aluminium section complete with easy-to- replace nylon brush, between door panel and side wall. Manual locking system by means of internal lever handle bolts with two locking points (top/bottom), galvanised steel rods with concealed guide latches (exclusive system); as an option, it is possible to have lever handle bolt with cylinder, key and external handle. - COLOURS AVAILABLE (similar to RAL) Flat panel, vertical micro-ribbing, pitch 160 mm - Smooth plate: White RAL 9002, Red RAL 3000, Green RAL 6005, Blue RAL 5010, Grey RAL 9006, Grey RAL 7016, Brown RAL 8019. - Stucco Embossed plate: White RAL 9002, Grey RAL 9006, Green RAL 6005. CE UNI EN 13241-1 A1:2011 MARKING DATA Product certification issued by Istituto Giordano Bellaria (RN). - Wind load resistance: Class 4 (kg. 100/mq., ca. 140Km/h) - Average thermal transmittance (U=W/m². K): 1.60 - Durability: 20,000 cycles - Average noise reduction: 22 db (not certifiable) - Fire resistance: B-S1, d0 Pag. 64 di 107

Warnings Dark colorations may give place to a temperature difference between inside and outside (on the side exposed to the sun) for more than 40 /45 degrees. This causes a door deformation which in case of a prolonged sun exposure may lead to a steel s breakaway from the insulating material; issue of physical-mechanical dilations and not of production defects. The producer, therefore, does not assume any responsibilities and does not recommend the use of dark colours on doors whose installation involves a prolonged sun exposure. OPTIONAL WICKET SWING DOOR - Without threshold (Minimum size for each pack Height over H>3000mm. and Width>2500mm.): cut panel door leaf with rebated upper frame made of black aluminium profile, equipped with panic push-bar with two locking points with cylinder and external handle. This door can be located on every panel of one or two pack doors, excluding lateral panels - with threshold, height 120 mm. (net free passage max mm. 1000x2100): door frame made of black aluminium section, can be painted as per request. One-point lock with cylinder and black handles; as an option, recessed triple lock or panic bar. This door can be located on every panel of the door. WINDOW -Rubber: surrounding frame made of black anti-ageing EPDM; cladding with 8/9 transparent stratified glass with rounded corners (radius 125 mm.). -Aluminium (thermal-break): window frame made of black aluminium profile with 90 corners, cladding with double glazing or stratified glass up to 40 mm thickness. NOTE: for constructional purposes, distance between the windows must be at least 500 mm. VENTILATION GRILLE Made of silver or black aluminium, with fixed blades, can be painted as per request. 60% ventilation. Dimensions available (WxH): 600x300 mm. and 1000x600 mm. ISOTHERM: THERMAL-BREAK VERSION SN can also be constructed in ISOTHERM version, the solution for doors with high thermal insulation. The exclusive panel with plastic frame (extruded Technopolymer EVICOM R450C) makes it possible to cut down heat dispersion (U=W/m². K) for more than 30%. Value measured on blank door 4500x4500H mm.: U=1.15. Maximum possible height 5000 mm. More details on page 101 AUTOMATION SYSTEMS PAGES 87 Pag. 65 di 107

SN FLUX - SUPPORTED SLIDING DOORS - G Mod. EK1000A, EK2000A The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 66 di 107

1) FACE FIXED WITH THE BOTTOM RAIL - INSIDE VIEW DETAIL OF TOP RAIL - MANUAL 210 110 H.F.M. = H. PAS. H.F.T. 210 CHAIN 195 35 DETAIL OF TOP RAIL - MOTOR OPERATED Horizontal section - OPENING TO 1 SIDE L.F.M = L.PAS. DETAIL OF BOTTOM RAIL 75 L.FT 75 Horizontal section - OPENING TO 2 SIDES L.F.M = L.PAS. 75 75 L.FT 28 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. 108 Pag. 67 di 107

1) FACE FIXED WITH THE BOTTOM RAIL - OUTSIDE VIEW DETAIL OF TOP RAIL - MANUAL 210 110 210 CHAIN COVER H.F.T. H.F.M. = H. PAS. DETAIL OF TOP RAIL - MOTOR OPERATED COVER Horizontal section - OPENING TO 1 SIDE 75 L.FT 75 DETAIL OF BOTTOM RAIL L.F.M = L.PAS. 85 Horizontal section - OPENING TO 2 SIDES L.FT 75 75 35 L.F.M = L.PAS. 28 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. 108 Pag. 68 di 107

1) REVEAL FIXED WITH THE BOTTOM RAIL - INSIDE VIEW DETAIL OF TOP RAIL - MANUAL COVER H. PAS. H.F.M. = H.F.T. DETAIL OF TOP RAIL - MOTOR OPERATED COVER Horizontal section - OPENING TO 1 SIDE CHAIN 75 L.F.M = L.PAS. L.FT 75 DETAIL OF BOTTOM RAIL 195 Horizontal section - OPENING TO 2 SIDES L.F.M = L.PAS. 35 75 75 L.FT The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. 108 28 Pag. 69 di 107

1) REVEAL FIXED WITH THE BOTTOM RAIL - OUTSIDE VIEW DETAIL OF TOP RAIL - MANUAL H.F.M. = H.F.T. H. PAS. Carter DETAIL OF TOP RAIL - MOTOR OPERATED CHAIN Horizontal section - OPENING TO 1 SIDE COVER 75 L.FT 75 DETAIL OF BOTTOM RAIL L.F.M = L.PAS. 85 Horizontal section - OPENING TO 2 SIDES L.FT 75 75 35 L.F.M = L.PAS. 28 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. 108 Pag. 70 di 107

BT SWING DOOR UNI EN 13241-1 A1:2011 CE CERTIFIED PRODUCT Swing door consisting of self-supporting monobloc panels of variable dimensions (55mm thick), perimeter frame consisting of dovetail shaped profile made of 20/10 thick galvanised steel (open section for integral injection), double galvanized (Sendzimir treatment) and pre-coated steel double sheet cladding (stucco embossed 5/10+5/10 thick) with protective film (to be removed within 15 days after installation), self-extinguishing Class B2 CFC-free polyurethane insulation injected using high pressure foaming cycle with a density of 40 kg/m³. Door frame and counter-frame for fixing on the wall made of black aluminium, can be painted on request, complete of spacers for fixing, sealing gasket, black aluminium contrast hinges. On the floor, easily replaceable nylon bottom brush, with adjustable supporting section made of black pre-coated aluminium; Configuration: one or two leaves (in this case the secondary one is provided with top/bottom lever handle lock). Closing by one point lock with cylinder and handle, on request recessed triple lock or panic bar. OPTIONAL WINDOW - Rubber: window frame made of black anti-ageing EPDM; cladding with 8/9 transparent stratified glass with rounded corners (radius 125 mm.). Aluminium (thermal-break): window frame made of black aluminium profile with 90 corners, cladding with double glazing or stratified glass up to 40 mm thickness. VENTILATION GRILLE Made of silver or black aluminium, with fixed blades, can be painted as per request. 60% ventilation. Dimensions available (WxH): 600x300 mm. and 1000x600 mm. - COLOURS AVAILABLE (similar to RAL) Flat panel, vertical micro-ribbing, pitch 160 mm - Smooth plate: White RAL 9002, Red RAL 3000, Green RAL 6005, Blue RAL 5010, Grey RAL 9006, Grey RAL 7016, Brown RAL 8019. - Stucco Embossed plate: White RAL 9002, Grey RAL 9006, Green RAL 6005. CE UNI EN 13241-1 MARKING DATA Product certification issued by Istituto Giordano Bellaria (RN). - Wind load resistance: Class 4 (kg. 100/m²., approx. 140km/h) - Average thermal transmittance (U=W/m². K): 1.78 - Average noise reduction: 22 db - Fire resistance: B-S1,d0 Pag. 71 di 107

BT EXIT -SWING DOOR 1) INSTALLATION WITH OPENING HORIZONTAL SECTION VERTICAL SECTION 1 LEFT 45 45 45 45 2 LEAVES 85 45 L.PAS. 45 L.F.M 45 45 H.PAS. H.F.M. = H.FT 85 45 L.PAS. L.F.M 45 10 1 PANEL LH 1 PANEL RH 2 PANELS : MAIN LH 2 PANELS: MAIN RH The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 73 di 107

1) INTERNAL INSTALLATION WITH OPENING HORIZONTAL SECTION 1 LEFT L.F.M 45 L.PAS. 85 VERTICAL SECTION 45 40 10 85 INTERNAL 40 2 LEAVES INTERNAL L.F.M 85 L.PAS. 85 40 H.F.M. = H.FT H.PAS. 85 40 INTERNAL 40 1 PANEL LH 1 PANEL RH 2 PANELS : MAIN LH 2 PANELS: MAIN RH The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 74 di 107

BT - ISOTHERM EXIT - ISOMAX - THERMAL-BREAK SWING DOOR 2) INSTALLATION WITH OPENING HORIZONTAL SECTION VERTICAL SECTION 1 LEFT 48 48 85 48 50 2 LEAVES 50 L.PAS. 50 L.F.M INTERNAL 48 48 85 INTERNAL H.PAS. H.F.M. = H.FT 50 L.PAS. 50 L.F.M INTERNAL 6 1 PANEL LH 1 PANEL RH 2 PANELS : MAIN LH 2 PANELS: MAIN RH The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 75 di 107

2) INTERNAL INSTALLATION WITH OPENING HORIZONTAL SECTION VERTICAL SECTION 1 LEFT 110 40 50 50 40 2 LEAVES 110 L.PAS. L.F.M 110 40 H.F.M. = H.FT 85 85 INTERNAL INTERNAL H.PAS. L.PAS. 40 40 INTERNAL L.F.M 6 1 PANEL LH 1 PANEL RH 2 PANELS : MAIN LH 2 PANELS: MAIN RH The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 76 di 107

WINDOWS Windows can be inserted in any panel of the folding or sliding door and the dimension can be customised to suit the door panels dimensions: -Rubber: surrounding frame made of black anti-ageing EPDM; cladding with 8/9 transparent stratified glass with rounded corners (radius 125 mm.). -Aluminium (thermal cut): Black aluminium profile painted as per request, 90 corners; cladding with double glazing or stratified glass up to 40 mm thickness. Standard windows are available in stock (rubber and aluminium), cladding with 8/9 transparent stratified antiinjury glass. Dimensions WxH (the dimension refers to the size of the glass): - 500 x 600 mm. - 500 x 800 mm. - 580 x 880 mm. - 700 x 700 mm. - 700 x 1000 mm. - 700 x 0 mm. - 700 x 2000 mm. - diameter 530 mm. (circular) VENTILATION GRILLE Ventilation grille made of silver or black aluminium, with fixed blades, can be painted as per request. Aeration surface 60%. Dimensions available (WxH): 600x300 mm. and 1000x600 mm. Pag. 77 di 107

WINDOW CROSS-SECTION WITH RUBBER FRAME AROUND THE PERIMETER 43 43 Glass 8/9 55 17 WINDOW SIZE (price list) 17 HOLE = WINDOW SIZE + 20mm WINDOW CROSS-SECTION WITH ALUMINIUM FRAME AROUND THE PERIMETER 44 44 Glass8/9 55 13 WINDOW SIZE (price list) 13 HOLE = WINDOW SIZE + 34mm. 44 double-glazed Glass 8/9 44 55 Glass6/7 13 WINDOW SIZE (prce list) 13 HOLE = WINDOW SIZE + 34mm. The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 78 di 107

GRILLE VENTILATION 40 40 H L L 55 40 40 H + 32 L + 32 L H Pag. 79 di 107

WICKET DOOR - Without threshold on LN and LE models (STHP001): cut panel with upper rebated profile made of black aluminium, fitted with panic bar with two locking points (top/bottom) with cylinder and external handle. An exclusive system increases the stability to a considerable extent; the overhead striker makes the door solidly connected with the upper and side panels, a special bracket allows optimum abutting against the locator on the floor. NOTE.: the panic push-bar latch acts on the floor striker of the door, there is no need to apply a specific one. - Cut panel STHP006(available only on SN model) cut panel with upper rebated section made of black aluminum, fitted with panic push bar with two lateral or vertical (it depends on the application type) locking points with rod and external handle. - Without threshold STHP008(available only on LG model): door with black aluminum frame on 3 sides, without lower cross beam, fitted with panic push bar with two lateral locking points with cylinder and external handle -Without threshold STHP005 for outdoor installation industrial door(available only on LN and LE models): Door with black aluminum frame on 2 sides, without lower cross beam, fitted with panic push bar with two (top/bottom) locking points with cylinder and external handle. - with threshold STHP010 (passage max mm. 1000x2100): surrounding frame made of black aluminum section, can be painted as per request. One-point locking mechanism with black handles; on request, recessed triple lock or panic push-bar. Pag. 80 di 107

TYPES OF WICKET DOOR STHP001 WICKET DOOR WITHOUT TRESHOLD FOR LN E LE MODELS Pag. 81 di 107

STHP006 W IC KET DO OR W IT HO UT T HRESHO LD F OR FLUX MO DEL STHP006 WICKET DOOR WITHOUT TRESHOLD FOR SN MODEL Pag. 82 di 107

STHP008 WICKET DOOR DOOR WITHOUT THRESHOLD TRESHOLD FOR FOR LIBRUM LG MODEL Pag. 83 di 107

STHP005 WICKET DOOR WITHOUT THRESHOLD TRESHOLD FOR FOR LIBER LN AND SMART LE MODELS M ODELS (OUTDOOR OR INSTALLATION) W. LEAF W. Passage = W. LEAF - 100mm. Black aluminium profile - RAL 9005 900 H. Standard 2060 mm. Pag. 84 di 107

STHP010 WICKET DOOR WITH THRESHOLD INSTALLATION ON EVERY MODEL Black aluminium frame - RAL 9005 W.max 1000 mm 100 H.max 2050 mm Pag. 85 di 107

PEDESTRIAN DOORS PLACEMENT: S M A RLE T - In te rn a l 2 L 1 L 1 L 1 R 2 L 1 L 1 R 2 L 1 L 1 R 2 R P 0 1 0 P 0 1 0 P 0 1 0 P 0 0 1 P 0 1 0 P 0 1 0 P 0 0 1 P 0 1 0 P 0 0 1 P 0 1 0 In te rn a l In te rn a l In te rn a l In te rn a l 2 + 0 1 + 1 2 + 1 2 + 2 3 L 2 L 1 L 1 R 2 R 3 L 2 L 1 L 1 R 2 R 3 R 4 L 3 L 2 L 1 L P 0 0 1 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 0 1 P 0 1 0 In te rn a l 3 + 2 In te rn a l 3 + 3 In te rn a l 4 + 0 4 L 3 L 2 L 1 L 1 R 2 R 4 L 3 L 2 L 1 L 1 R 2 R 3 R 4 R P 0 0 1 P 0 0 1 P 0 1 0 P 0 1 0 P 0 0 1 P 0 1 0 P 0 0 1 P 0 1 0 In te rn a l 4 + 2 In te rn a l 4 + 4 S M A RLE T - E x te rn a l 2 L 1 L 1 L 1 R 2 L 1 L 1 R 2 L 1 L 1 R 2 R P 0 1 0 P 0 1 0 P 0 1 0 P 0 0 1 P 0 1 0 P 0 1 0 P 0 0 1 P 0 1 0 P 0 0 1 P 0 1 0 2 + 0 1 + 1 2 + 1 2 + 2 e x te rn a l e x te rn a l e x te rn a l e x te rn a l 3 L 2 L 1 L 1 R 2 R 3 L 2 L 1 L 1 R 2 R 3 R 4 L 3 L 2 L 1 L P 0 0 1 P 0 0 1 P 0 1 0 P 0 1 0 P 0 0 1 P 0 1 0 e x te rn a l 3 + 2 e x te rn a l 3 + 3 e x te rn a l 4 + 0 4 L 3 L 2 L 1 L 1 R 2 R 4 L 3 L 2 L 1 L 1 R 2 R 3 R 4 R P 0 0 1 P 0 0 1 P 0 1 0 P 0 1 0 P 0 0 1 P 0 1 0 P 0 0 1 P 0 1 0 4 + 2 4 + 4 e x te rn a l e x te rn a l Pag. 86 di 107

LIBER LN - Internal 2L 1L 3L 2L 1L 4L 3L 2L 1L 2L 1L 1R P001 P010 P005 P010 P001 P010 P001 P001 P010 P010 Inside Inside Inside Inside 2+0 3+0 4+0 2+1 2L 1L 1R 2R 3L 2L 1L 1R 2R 4L 3L 2L 1L 1R 2R P001 P010 P001 P010 P005 P001 P010 P010 P001 P001 P010 P010 Inside 2+2 Inside 3+2 Inside 4+2 4L 3L 2L 1L 1R 2R 3R 4R P005 P005 P010 P010 P001 P010 P001 P010 Inside 3+3 Inside 4+4 LIBER LN - External 2L 1L 3L 2L 1L 4L 3L 2L 1L 2L 1L 1R P001 P010 P005 P010 P001 P010 P001 P001 P010 P010 O utside 2+0 O utside O utside O utside 3+0 4+0 2+1 2L 1L 1R 2R 3L 2L 1L 1R 2R 4L 3L 2L 1L 1R 2R P001 P010 P001 P010 P005 P001 P010 P010 P001 P001 P010 P010 O utside Outside O utside 2+2 3+2 4+2 4L 3L 2L 1L 1R 2R 3R 4R P005 P005 P010 P010 P001 P010 P001 P010 O utside O utside 3+3 4+4 Pag. 87 di 107

LIBRUM LG - Internal 3L 2L 1L 4L 3L 2L 1L 5L 4L 3L 2L 1L 6L 5L 4L 3L 2L 1L P008 P010 P010 P008 P010 P008 P010 P010 P008 P010 Internal 3+0 4+0 5+0 6+0 8L 7L 6L 5L 4L 3L 2L 1L 3L 2L 1L 1R 2R 3R P010 P008 P010 P008 P010 P008 P010 8+0 3+3 4L 3L 2L 1L 1R 2R 3R 4R 5L 4L 3L 2L 1L 1R 2R 3R 4R 5R P010 P008 P008 P010 P010 P010 P008 P010 P008 P010 4+4 5+5 6L 5L 4L 3L 2L 1L 1R 2R 3R 4R 5R 6R P010 P008 P008 P010 P010 P010 6+6 8L 7L 6L 5L 4L 3L 2L 1L 1R 2R 3R 4R 5R 6R 7R 8R P010 P008 P010 P008 P010 P010 8+8 LIBRUM LG - External ( contact technical office) Pag. 88 di 107

F L USN X - In te rn a l e d E x te r n a l 1 0 0 0-1 0 0 0 /N (h a n g in g ) 2 L 1 L 3 L 2 L 1 L 4 L 3 L 2 L 1 L 5 L 4 L 3 L 2 L 1 L P 0 1 0 P 0 1 0 P 0 0 6 P 0 1 0 P 0 1 0 P 0 1 0 P 0 0 6 P 0 1 0 P P 0 0 1 0 0 6 P 0 1 0 P 0 1 0 P 0 0 6 P 0 1 0 P P 0 0 0 1 6 0 P P 0 0 1 0 0 6 P 0 1 0 P 0 1 0 E x t e rn a l 2 + 0 3 + 0 4 + 0 5 + 0 In t e rn a l 6 L 5 L 4 L 3 L 2 L 1 L 1 L 1 R 2 L 1 L 1 R 2 R P 0 1 0 P 0 0 6 P 0 0 6 P 0 0 6 P 0 0 6 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 0 6 P 0 0 6 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 6 + 0 1 + 1 2 + 2 4 L 3 L 2 L 1 L 1 R 2 R 3 R 4 R P 0 1 0 P P 0 0 1 0 0 6 P 0 0 6 P 0 0 6 P 0 0 6 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P P 0 0 1 0 0 6 P P 0 0 1 0 0 6 P 0 0 6 P 0 0 6 P 0 1 0 P 0 1 0 P 0 0 6 P 0 1 0 P 0 0 6 P 0 1 0 P 0 1 0 3 + 3 4 + 4 F L USN X - In te rn a l e d E x te r n a l 1 0 0 0 /A ( le a n in g ) 2 L 1 L 3 L 2 L 1 L 4 L 3 L 2 L 1 L 5 L 4 L 3 L 2 L 1 L P 0 1 0 P 0 1 0 P 0 0 6 P 0 1 0 P 0 1 0 P 0 1 0 P 0 0 6 P 0 1 0 P P 0 0 1 0 0 6 P 0 1 0 P 0 1 0 P 0 0 6 P 0 1 0 P P 0 0 0 1 6 0 P P 0 0 1 0 0 6 P 0 1 0 P 0 1 0 2 + 0 3 + 0 4 + 0 5 + 0 6 L 5 L 4 L 3 L 2 L 1 L 1 L 1 R 2 L 1 L 1 R 2 R P 0 1 0 P 0 0 6 P 0 0 6 P 0 0 6 P 0 0 6 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 6 + 0 1 + 1 2 + 2 3 L 2 L 1 L 1 R 2 R 3 R 4 L 1 L 1 R 2 L 2 R 3 L 3 R 4 R P 0 0 6 P 0 0 6 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P P 0 0 1 0 0 6 P 0 0 6 P 0 0 6 P 0 1 0 P 0 0 6 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 P 0 1 0 3 + 3 4 + 4 Pag. 89 di 107

AUTOMATION SYSTEMS 1) FOLDING DOOR WITHOUT BOTTOM RAIL A) LN: mod. 1002MO(2+0), 2002MO(1+1), 2003MO(2+1), 2004MO(2+2) pack at 90/180 Electro-mechanical motor fixed on housing provided in the top rail G (PATENTED SYSTEM) which allows movement through 90 and 180 ; movement by means of arm complete with ring nut for fixing to the motor. Emergency manoeuvre with release rope positioned at eye level. (rail with provision, disassembled motors) B) LN: mod. 1004MO(4+0) pack at 90 Electro-mechanical motor fixed to the panel by means of a special housing plate; movement by means of telescopic arm complete with ring nut for fixing to the motor. Emergency manoeuvre with release rope positioned at eye level. (motors assembled on panels). TECHNICAL DATA Unit 161 mod. KBS200IDE (right) Unit 161 mod. KBS200ISE (left) Supply voltage Motor 230V +/- 10% 50Hz 4 poli; 1400 giri/min. Condensers 10µF Power 360W Reducers 1:1178 Shaft rotation speed Torque 1,20giri/min. 500Nm Work cycles (activation) 20% Thermal probe 135 C Opening time (90 rotation) 13 Opening time (180 rotation) 26 Protection Protection with guard IP50 IP53 Pag. 90 di 107

OPEN ATTEN ZIO NE! TOGLIERE TENSI ONE PRIMA DI APRI RE IL COPERCHIO W ARN ING! DI SCONNECT POWER BEFORE REMOVING THE COVER 23 0V CLOSE EME R GE NCY S T OP PO WER DI APRIRE IL COPERCHIO REMOVING THE COVER EMERGENCY AUTOMATION SYSTEMS 1) FOLDING DOOR WITHOUT BOTTOM RAIL A ) LIBER LN mod. 1002MO, 2002MO, 2003MO, 2004MO 3 4 5 6 2 7 230V ATTENZIONE! TOGLIERE TENSIONE PRIMA WARNING! DISCONNECT POWER BEFORE S T O P 1 OPEN CLOSE POWER ATTENZIONE! TOGLIERE TENSIONE PRIMA DI APRIRE IL COPERCHIO WARNING! DISCONNECT POWER BEFORE REMOVING THE COVER E S T OP 8 OPEN CLOSE POWER 1 - Device for manual release : motor deactivated 2 - LH motor housed in the upper rail 3 - Fixing telescopic arm to LH lateral bracket 4 - Device for manual release: motor activated 5 - Fixing telescopic arm to RH lateral bracket 6 - RH motor housed in the upper rail 7 - Control panel with built-in pushbuttons 8 - Pushbutton for Deadman control and pushbutton with three keys for Automatic Logic controls 9 - Safety microswitch for door with wireless transmitter 9 The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 91 di 107

OPE N ATT ENZI ONE! TOGLIERETENSI ONEPRIMA DIAPRI REIL COPERCHI O W AR NI NG! DISCONNECT POWER BEFORE REMOVING THECOVER 2 30V EM CLO SE ERGENCY STO P POW ER DI APRIRE IL COPERCHIO REMOVING THE COVER EMERGENCY AUTOMATION SYSTEMS 1) FOLDING DOOR WITHOUT BOTTOM RAIL B ) LIBER LN mod. 1004MO 3 4 5 6 2 7 230V ATTENZIONE! TOGLIERE TENSIONE PRIMA WARNING! DISCONNECT POWER BEFORE S T OP OPEN CLOSE POWER 1 ATTENZIONE! TOGLIERE TENSIONE PRIMA DI APRIRE IL COPERCHIO WARNING! DISCONNECT POWER BEFORE REMOVING THE COVER E S T O P 8 OPEN CLOSE POWER 1 - Device for manual release : motor deactivated 2 - Device for manual release: motor activated 3 - Motor installed on board the panel by means of special bracket 4 - Fixing telescopic arm to central carriage 5 - Motor installed on board the panel by means of special bracket 6 - Motors power supply line 7 - Control panel with built-in pushbuttons 8 - Pushbutton for Deadman control and pushbutton with three keys for Automatic Logic controls The Manufacturer reserves the right to modify, supplement and improve the manual, any time, without the present publication being for that reason considered inadequate. Pag. 92 di 107

2) FOLDING DOOR WITH BOTTOM RAIL/SLIDING DOOR A) LG: mod. 1003MOS(3+0), 1004/MOS(4+0), 1005MOS(5+0), 1006MOS(6+0), 1008MOS(8+0), 2006MOS(3+3), 2008MOS(4+4) B) SN: mod. EK1000 (opening to 1 side), EK2000 (opening to 2 sides) DOORS UP TO 30 M 2 PER LEAVES PACK HEAVY-DUTY MOTORIZATION Electro-mechanical motor fixed on RH or LH, on special support has to be inserted on top rail G (PATENTED SYSTEM); chain with tightener and carriage connection, mechanic limit switches, Emergency manoeuvre with release rope positioned at eye level; included in the supply. TECHNICAL DATA MR33/LS63MS MR33/LS71MS Supply voltage 230V 50Hz 230V 50Hz Absorption 2.5A 3.2A Power 350W 400W Condenser 20µF 25µF Torque 25Nm 35Nm Work cycles (activation) 100% 100% Shaft rotation speed 40 rpm. 40 rpm. Linear speed (opening closure) 10m/min. 10m/min. Pag. 93 di 107

C) LG: mod.1005mos(5+0), 1006MOS(6+0), 1008MOS(8+0), 2006MOS(3+3), 2008MOS(4+4) D) SN: mod. EK1000 (opening to 1 side), EK2000 (opening to 2 sides) DOORS OVER 30M 2 PER LEAVES PACK HEAVY-DUTY MOTORIZATION Electro-mechanical motor fixed on RH or LH, on special support to be inserted on top rail G (PATENTED SYSTEM); chain with tightener and carriage connection, mechanic limit switches, Emergency manoeuvre with release rope positioned at eye level; included in the supply.. TECHNICAL DATA MR33/LS63TS MR33/LS71TS Power supply 400V 50Hz 400V 50Hz Power 370W 370W Absorption 1.1A 1.1A Torque 25Nm 40Nm Work cycles (activation) 100% 100% Shaft rotation speed 40 rpm 40 rpm Linear speed (opening closure) 10m/min 10m/min Pag. 94 di 107

TYPES OF MOTORIZATION : LN MOD. 1003/MO/S LN MOD. 1004/MO/S Pag. 95 di 107

LG MOD. 1005/MO/S LG MOD. 1006/MO/S Pag. 96 di 107

LG MOD. 2006/MO/S LG MOD. 1008/MO/S Pag. 97 di 107

LG MOD. 1008/MO/S Pag. 98 di 107

DRIVE UNIT KIT 1) FOLDING DOOR WITHOUT BOTTOM RAIL A) LE mod. 1002S(2+0), 2002S(1+1), 2003S(2+1), 2004S(2+2) B) LN mod. 1004MO(4+0) C) LN mod. 1002MO(2+0), 2002MO(1+1), 2003MO(2+1), 2004MO(2+2) DEADMAN LOGIC Motor/s and accessories for opening the door, release for manual operation. Control panel containing electronic board for controlling the motor movements that can work only at deadman logic, Control push-button panel, OPEN/CLOSE. Safety micro switch on wicket door with wireless signal transmission device (500 mm.). AUTOMATIC LOGIC Motor with accessories for the door opening, release for manual operation. Control panel containing electronic board for controlling the motor movements with integrated push-button panel: - Open/ Close buttons with deadman operation (stop on release); - Start button (central button) with automatic operation which depends on the desired programming type (Open-Stop-Close-Stop-Open or Open-Automatic Closing) - Emergency stopping button, it works stopping the door s Automatic operation. No. 1 intermittent light signal (flashing) for signalling moving door. No. 1 pair of external photocells which has to be installed at a height of 500 mm. off the ground for detecting the presence of a mobile obstacle. Safety micro switch on wicket door with wireless signal transmission device (500 mm). Safety micro switch for lever handle lock, provided on supporting brackets to be fixed in rail. NOTE: If the door s height is less than 2500 mm. the DEADMAN logic is mandatory. NOTE: The central unit is fitted with certified AMPERO STOP (obstacle detector) safety system. This device allows to omit the installation of sensible edge on door s panels or on adjacent structures, however in full respect of existing safety anti crushing regulation. This device s efficiency is only ensured in accordance with the best practice of installation, because the presence of friction must be avoided (for example strong rubbing between brush and floor). It is clarified that in case of wind speed exceeds 40-50 km/h, this device can intervene (stopping the door s operating) identifying it as an obstacle. In any case the maximum area s door mustn t exceed 18 m 2 per pack. NOTE: In case of outdoor installation, the engines are assembled externally, this way it s easier to tamper. The prevention from burglary is guaranteed by the interior lever handle locking. Pag. 100 di 107

2) FOLDING DOOR WITH BOTTOM RAIL LG DEADMAN LOGIC Motor/s with accessories for the door opening, release for manual operation. Control panel containing electronic board for controlling the motor movements that can work only at deadman logic, Control pushbutton panel, OPEN/CLOSE. Safety micro switch on pedestrian door with wireless signal transmission device. AUTOMATIC LOGIC Motor with accessories for the door opening, release for manual operation. Control panel containing electronic board for controlling the motor movements with integrated push-button panel: - Open/ Close buttons with deadman operation (stop on release); - Start button (central button) with automatic operation which depends on the desired programming type (Open-Stop-Close-Stop-Open or Open-Automatic Closing) - Emergency stopping button, it works stopping the door s Automatic operation. No. 1 intermittent light signal (flashing) for signalling moving door. No. 1 pair of external photocells which has to be installed at a height of 500 mm. off the ground for detecting the presence of a mobile obstacle. Vertical sensitive edge positioned on one of the top panels (height to be protected 2500 mm off the ground) with wireless signal transmission device. Horizontal sensitive edge (L. 0 mm.) positioned at a height of 500 mm. off the ground (if the distance between the pack of door panels and wall is <500 mm.) Safety micro switch on wicket door with wireless signal transmission device. NOTE: If the door s height is less than 2500 mm. the DEADMAN logic is mandatory. NOTE: In case of outdoor installation, the engines are assembled externally, this way it s easier to tamper. The prevention from burglary is guaranteed by the interior lever handle locking Pag. 101 di 107

3) SLIDING DOOR SN DEADMAN LOGIC Motor with accessories for the door opening, release for manual operation. Control panel containing electronic board for controlling the motor movements that can work only at deadman logic, Control pushbutton panel, OPEN/CLOSE. Safety microswitch on pedestrian door with wireless signal transmission device. AUTOMATIC LOGIC Motor with accessories for the door opening, release for manual operation. Control panel containing electronic board for controlling the motor movements with integrated push-button panel: - Open/ Close buttons with deadman operation (stop on release); - Start button (central button) with automatic operation which depends on the desired programming type (Open-Stop-Close-Stop-Open or Open-Automatic Closing) - Emergency stopping button, it works stopping the door s Automatic operation. No. 1 flashing intermittent light for signalling door movement. No. 1 pair of external photocells which has to be installed at a height of 500 mm. off the ground, for detecting the presence of obstacle. Vertical sensitive edge positioned on upper door panel (height to be protected 2500 mm off the ground) with wireless signal transmission device. Safety micro switch on pedestrian door with wireless signal transmission device. Vertical sensitive edge fixed to the wall in case of obstacle at the end less than 500 mm. (height to be protected 2500 mm. off the ground. NOTE: If the door s height is less than 2500 mm. the DEADMAN logic is mandatory. NOTE: In case of outdoor installation, the engines are assembled externally, this way it s easier to tamper. The prevention from burglary is guaranteed by the interior lever handle locking Pag. 102 di 107

OPTIONAL ACCESSORIES DEADMAN LOGIC External key-operated selector. AUTOMATIC LOGIC Receiver with antenna. Radio control (two channels or four channels). External key-operated selector. Volumetric radar. Magnetic coil. Pull rope selector. Pag. 103 di 107

ISOTHERM energy saving system (evolution of industrial doors) ISOTHERM is the solution for Industrial doors with high thermal insulation. It s the latest evolution of the family, which combines a unique aesthetic appeal with the typical benefits of products. High level of safety Conformity to new European Standards Innovative technical solutions Low maintenance Large possibility of options and accessories In the development of ISOTHERM, in addition to searching for the traditional strength and safety of its products, the producer has improved the Thermal Transmittance efficiency (U expressed in W/mq. K) to a considerable extent, by developing a sandwich panel (8/10 pre-coated sheet steel, a special frame and polyurethane foam without CFC) which reduces for 30% of the heat dispersion. Frame made of Extruded Technopolymer EVICOM R450C Thermal conductivity (DIN 52612) λ = 0,14-0,16 Watt/m K Polyurethane foam without CFC dovetail profile for concealed hinge, patented 8/10 steel prepainted sheet Thanks to the new panel, it is possible to construct doors, the only ones of their kind, able to satisfy (also in configurations with double glazed windows), the requirements of Thermal Transmittance required by the Laws in all national Climatic Zones Thanks to the ISOTHERM Series it is possible to select the most technical solution suitable for the requirements of space and logistic flow of operating activities, with the certainty of improving the thermal features of the industrial building, thereby ensuring immediate tax savings and low energy costs.. NATIONAL CLIMATIC ZONES ACCESS TO TAX BENEFITS - 55% * ) * ) DAY DEGREES Traditional parameter that represents the winter climatic conditions of every municipality: the higher the number of day degrees and the colder it is in winter and the longer the winter heating period. Value calculated on 4-leaf door, 4 windows 580x880 8/9 th., LxH 4500x4500 Competitor s door A Industrial door 2.16 W/mq. K A B ISOTHERM door 2.48 W/mq. K 1.67 W/mq. K A B C D E F CLIMATIC ZONES The day degrees intervals are identified; those with the highest limits of day degrees are the coldest * ) D.L. 26.01.2010 in force until 31/12/2011 Pag. 104 di 107

For the ISOTHERM Series, in combination with the industrial door, the producer has developed a swing door with thermal-break profile which makes it possible to obtain a Thermal Transmittance value U equal to 1.30 W/mq. K (value measured on 1300x2200 mm blind door ). Prepainted aluminium frame Thermal cut profile. 8/10 prepainted steel sheet Polyurethane foam without CFC 54 mm thick panel The swing door has the same looks as the industrial door and matches it perfectly on the building façade. It is available in the following configurations: Opening with 1 or 2 panels Closure mechanism with lock or panic push-bar Larger adjustable hinges Addition of window and/or ventilation grilles The ISOTHERM Series is completed with a window with pre-coated aluminium surrounding frame, with low emission double glazed glass 8/9+9+6/7. CONFIGURATIONS AVAILABLE ISOTHERM can be applied to all industrial doors. (LE, LN, LG, SN) with a height limitation of 5000 mm. and to swing doors (BT). Pag. 105 di 107