EROAD Ehubo2 Installation Guide

EROAD Ehubo2 Installation Guide

3 Ehubo2 installation - Overview IMPORTANT: Do not install or use the Ehubo2 until you have read this Installation Guide thoroughly. The Ehubo2 is easy to install by carrying out the following steps as described in this Guide: 1. Make sure to read the Safety Information section, familiarise yourself with the local laws regarding the installation and use of the Ehubo2, and use and follow all standard safety precautions. 2. Choose a suitable mounting location and mount the Ehubo2. 3. Install the Ehubo2 by connecting it to the vehicle. 4. Complete the installation by following the Ehubo2 s on-screen guide. Refer to Replacement Installation on page 12 if you are installing a replacement Ehubo2 2016 EROAD. Doc 100200AA1.10. 7/2016. By using this Ehubo you are agreeing to be bound by EROAD s Terms of Use that can be located at www.eroad.com.

4 Important Safety Information Please read carefully before beginning installation! LEGAL NOTICE AND DISCLAIMER The legislation and rules concerning the installation and operation of GPS driver aids and messaging devices such as the Ehubo2 vary from each country and state. Please familiarize yourself with the laws of the jurisdiction(s) in which the vehicle will be operated in prior to installing and using the Ehubo2. Driving laws place the responsibility on the driver to correctly install and use GPS driver aids. It is therefore the Customer s responsibility to install and use the Ehubo2 in a manner that complies with the law and will not cause accidents, personal injury or property damage. The owner of this Ehubo2 is responsible for observing safe driving practices. EROAD DISCLAIMS ALL LIABILITY FOR ANY USE OF THIS EHUBO2 IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR VIOLATE THE LAW. TO THE MAXIMUM EXTENT PERMITTED BY LAW, ALL REPRESENTATIONS AND WARRANTIES (EXCEPT ANY WHICH MAY NOT LAWFULLY BE EXCLUDED) ARE EXPRESSLY EXCLUDED, INCLUDING WITHOUT PREJUDICE TO THE GENERALITY OF THE FOREGOING, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. As EROAD is continuously improving its products, EROAD may make changes to the Ehubo2 at any time which may not be reflected in this document. Please contact your nearest EROAD office if you require any further assistance. PERSONAL PROTECTIVE EQUIPMENT (PPE) Federal, national or local health and safety regulations may require wearing appropriate Personal Protective Equipment (PPE). PPE may include items such as safety glasses, safety shoes, work gloves, hard hat, high visibility vest, and work uniform. Make sure to comply with appropriate standards and check with customers or third parties to verify whether they have additional PPE requirements. INSTALLATION Installers and contractors must follow all health and safety regulatory requirements to ensure a safe and healthy work environment. Whenever the equipment is parked, the parking brake shall be set. Equipment parked on inclines shall have the wheels chocked and the parking brake set. Equipment, or parts thereof, which are suspended or held aloft by use of slings, hoists, or jacks shall be substantially blocked or cribbed to prevent falling or shifting before employees are permitted to work under or between them. Installing and servicing electronic devices can be hazardous due to electrical components. Make sure to create a safe working environment to avoid hazards and to ensure correct and safe installation and operation. EROAD recommends the use of a qualified professional automotive technician to install the Ehubo2. Make this Installation Guide available to the appropriate personnel. Store it for future reference. To avoid damage do not run cables close to heat sources, sharp edges or other obstacles that might damage them. Do not run cables directly next to safety-relevant devices. Do not damage existing wiring and components when drilling the dashboard. Avoid fitting the Ehubo2 in a location that could cause injury to a driver or passenger in a crash. This includes potential head strike zones on the windshield or dashboard, or other locations where a deploying airbag may contact the Ehubo2. Do not block or impair the deployment of airbags and other safety-relevant devices.

5 Avoid placing the Ehubo2 where it may impede or limit the driver s movement when driving or exiting the vehicle (including in an accident). After installation, check that all safety-relevant equipment is working properly. OPERATION Familiarize yourself with local laws concerning the use of GPS driver aids. Some countries and states prohibit drivers from viewing screens or making or receiving text messages while driving a vehicle. Only operate or look at the Ehubo2 when it is safe to do so. Do not message, change settings or access functions while driving. Pull over before you wish to attempt such activities. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety. Where the screen displays the speed limit or the vehicle s speed, this is for information only. Please ensure that you observe all posted speed limits and drive to the conditions. Do not use sharp-edged objects on the Ehubo2 touch screen. The Ehubo2 is not waterproof. Do not spill any liquid on it. Protect the Ehubo2 from extreme temperatures. Operating temperature for the Ehubo2 is between -20 C/-4 F and 85 C/185 F. Always follow local regulations when disposing of the Ehubo2. Do not dispose of the battery in trash cans, fire or water. FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RAM 6 Inside the box Open your Ehubo2 box and check that everything is inside. EROAD Ehubo Installation Guide EROAD RAM EROAD Ehubo2 (pre-fitted wiring loom) This installation guide Ehubo2 mount A B TECHNICAL CLEANING WIPE Fuse kit (permanent power/ignition) Alcohol wipe Mounting plate High strength adhesive tape (optional, for tape mount) C 2 x ¾ / 19mm screws + washers D 4 x ½ / 13mm counter sunk screws + nyloc nuts F E 4 x 1 / 25mm screws + nuts Screws, nuts and washers to mount Ehubo2 Cable ties Rear hatch security plugs

7 Mount the Ehubo2 The Ehubo2 can be mounted on the dashboard or windscreen (where permitted by law where the vehicle is being operated). For windscreen mount or temporary installation on a flat surface please use the adhesive tape supplied. NOTE: Choose the mounting location for your Ehubo2 carefully and ensure that it complies with all local regulations. Make sure that the Ehubo2 does not impair the driver s visibility, does not pose a risk in the event of an accident, does not interfere with any systems used in the operation of the vehicle, does not block or impair the deployment of the airbag, and has a good view of the sky. Choose a location that does not expose the Ehubo2 to excessive temperature or vibration. 1 Insert the two rear hatch security plugs. The plugs are keyed and only fit in their correct position. Proceed with 2A PERMANENT MOUNT (dashboard) or 2B TAPE MOUNT (windscreen or flat surface). 2A PERMANENT MOUNT Attach mount to dash using mounting plate (A), screws and nuts (E). or 2B TAPE MOUNT Clean flat surface with alcohol wipe Fit mounting plate (A) to mount using counter sunk screws/holes and nuts (D) Apply adhesive tape (B) to mounting plate and firmly press to surface E A A B D Attach Ehubo2 to the mount using screws and washers (C). Use of the washers is essential to reliably secure the Ehubo2! 3 4 Route the Ehubo2 wiring out of the way and down the back of the dashboard. C RAM RAM NOTE: If swapping mounting option do not re-use nyloc nuts, use unused nuts as supplied.

8 Install the Ehubo2 NOTE The engine must be turned off prior to installing the Ehubo2. Do not connect in any way to a CANBUS or other engine management system. Power supply must not be taken from any ABS/EBS braking system. The Ehubo2 needs a permanent power source and a good view of the sky to operate optimally. While the vehicle is off, the Ehubo2 will shut down to a low power mode and will draw a very small current from the vehicle supply. Remove the Ehubo2 permanent power fuse if the vehicle is in storage or parked up for more than a month to avoid discharging the vehicle battery. WIRING The Ehubo2 is fitted with a wiring loom which is used to connect to the vehicle and for optional digital inputs. NOTE: Fuse connections at vehicle connection points to protect the wiring in case of a short circuit. WIRE FUNCTION FUSE NOTES Red Yellow +12V / 24V DC Supply Ignition (True Idle) Use supplied fuse kit Connect to a 12V or 24V DC permanent power source. Connect to ignition. Black Ground Do not fuse Connect to an appropriate Grounding location that is considered fit for purpose. Purple Speed Signal (+ve) Do not fuse Analogue (+ve) speed signal OR Digital speed signal input Blue Speed Signal (-ve) Do not fuse Analogue (-ve) speed signal OR if using digital signal this must be Grounded Orange Digital Input 1 Brown Digital Input 2 Fuse individually with 3A fuse Optional digital inputs for integration purposes. Gray Digital Input 3

9 INSTALLING THE EHUBO Refer to wiring diagrams and table in this Guide. 1. Connect the black wire to an appropriate Grounding location that is considered fit for purpose. 2. Connect the red wire to a permanent power source. 3. Connect the yellow wire to ignition that is switched on when the engine is running and off when the engine is not running (true idle). Connection to the alternator may be necessary. 4. Connect the blue wire to a Speed Signal (-ve) or Ground. 5. Connect the purple wire to a Speed signal (+ve). 6. If required, connect additional wires (orange, brown and gray) for monitoring vehicle activity on three digital inputs. Refer to Wiring Diagram Additional Inputs and table above. 7. Trim and make safe all unused wires. 8. Pull the sticker and screen protection film off the Ehubo2 screen. 9. To complete the installation, follow the instructions on the screen. At the end of the process the Ehubo2 Home screen will appear, and the installation is complete. NOTE: If the screen remains black or if you cannot successfully complete the instructions on the screen, the wiring of the Ehubo2 may not be quite right. Please refer to the Wiring Diagrams in this Installation Guide or to the Troubleshooting section and adjust your wiring. If the screen still remains black, please contact the EROAD Helpdesk. The installation remains unfinished until the on-screen instructions have been successfully completed!

10 Wiring Diagram Standard On heavy vehicles leave sufficient cable exposed to permit handing unit to enforcement officer Note: Ensure wiring is neatly routed to under the dash EROAD RAM Dashboard Cable clamp or heat shrink Fuses must be fitted at connection point. This is to protect the wire in case of a short Vehicle wiring harness IGN +ve Cut wire loop and connect fuse inline RED Permanent Power (12V or 24V) YELLOW BLACK PURPLE BLUE Switched Ignition (True Power Idle) (Engine on/off) Ground Speed Signal (+ve) Speed Signal (-ve) or Ground Any unused wiring should be trimmed neatly and made safe Ignition input should always reflect the engine state for calculating true idle. Alternator connection is supported Existing Installs To uninstall an Existing Ehubo1, disconnect the Ehubo1 from the vehicle wiring harness and insert the Ehubo2 connector in its place. Use a cable clamp or heat shrink to secure the connection and hide it beneath the dash. Remove the window mount and Driver ID module and loom (if present) that were previously used by the Ehubo1, and clean up any adhesive residue.

11 Wiring Diagram Additional inputs Additional connections are available for three digital inputs orange, brown and gray wires. If used, they must be fused individually using 3A fuses. Below is the connection diagram showing the additional input connections. Example inputs include things such as PTO, lights, generator etc. On heavy vehicles leave sufficient cable exposed to permit handing unit to enforcement officer Note: Ensure wiring is neatly routed to under the dash EROAD RAM Dashboard Cable clamp or heat shrink Fuses must be fitted at connection point. This is to protect the wire in case of a short Vehicle wiring harness IGN +ve Cut wire loop and connect fuse inline RED YELLOW BLACK PURPLE BLUE ORANGE BROWN GRAY Permanent Power (12V or 24V) Ignition Switched (True Power Idle) (Engine on/off) Ground Speed Signal (+ve) Speed Signal (-ve) or Ground Digital input Input 1 Digital input Input 2 Digital Input 3 Any unused wiring should be trimmed neatly and made safe 3A 3A 3A Ignition input should always reflect the engine state for calculating true idle. Alternator connection is supported

12 Replacement installation To replace an existing Ehubo2, - disconnect the power cable from the existing Ehubo2 and - connect it to the replacement Ehubo2. NOTE: Turn off the engine prior to replacing the Ehubo2 Follow these simple steps: 1 Remove the existing Ehubo2 from its mount and carefully place it screen down on a clean, flat surface. Make sure to not scratch or damage the screen! RAM 2 Unpack the replacement Ehubo2 and also place it screen down on a clean, flat surface. Make sure to not scratch or damage the screen! 3 Remove the rear hatch security plugs (F) of both, the existing and the replacement Ehubo2. This is easily done by inserting a flathead screwdriver and scooping out the plug. Unwind the screw underneath (G). 4 Lift the rear hatch (H) off the existing Ehubo2 and slide it off the cable grommet (I). Lift the rear hatch off the replacement Ehubo2. F I G H 5 EXISTING EHUBO2: Push down the cable plug latch to release the cable plug (J) and carefully slide the cable plug off the internal connector (K). 6 REPLACEMENT EHUBO2: Carefully insert the cable plug (J) to the internal connector (K). Make sure the cable plug latch clicks into place to safely secure the plug. K K J J

13 Slide the replacement Ehubo2 s rear hatch (H) onto the cable grommet (I) and insert it into the replacement Ehubo2. 7 8 Insert the two rear hatch screws (G) and new security plugs (F). H F G I 9 Mount the replacement Ehubo2 on the existing mount using the screws and washers (C) supplied with the replacement Ehubo2. C RAM 10 Pull the sticker and screen protection film off the Ehubo2 screen. 11 To complete the installation, follow the instructions on the screen. At the end of the process the Ehubo2 Home screen will appear, and the installation is complete. 12 Please place the uninstalled Ehubo2 in the replacement box and return to EROAD including surplus parts.

14 Troubleshooting This section will provide some solutions if the installation of your Ehubo2 is unsuccessful or the Ehubo2 doesn t perform as expected. SCENARIO SYMPTOM SOLUTION Permanent Power is not connected correctly Ehubo2 screen remains off Green Power LED on the Ehubo2 is off while driving Cannot successfully complete install checks Check that Permanent Power has been properly connected to the red wire. Check you have a good Ground connection connected to the black wire. Check the fuses have been inserted properly Ensure that the permanent supply is capable of supplying the Ehubo2 (12V/24V) Ignition is not connected correctly Poor or no cellular connection after 1-2 minutes AND/OR Poor or no GPS reception Ehubo2 screen remains off Cannot successfully complete install checks Engine on/off icon shows incorrectly Ehubo2 indicates poor or no cellular reception 3G Ehubo2 indicates poor or no GPS reception Check that the fuses have been inserted. Check that permanent power has been properly connected to the red wire. Check that the ignition has been properly connected to the yellow wire. Ensure vehicle is in a location with adequate cellular coverage Ensure Ehubo2 has good view of the sky in the vehicle and the vehicle is moved away from overhead obstructions Ehubo2 screen is blank Ehubo2 screen remains off after touch Ensure the vehicle is stationary Ensure Permanent Power, Ignition and Ground are connected correctly If any of these icons are present, please contact your supervisor or employer Faulty ignition Faulty SIM Faulty connection Faulty GPS

15 LIBZINT - THE OPEN SOURCE BARCODE LIBRARY LICENSE Copyright (C) 2008 Robin Stuart Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of the project nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. GOOGLE PROTOCOL BUFFER SOFTWARE LICENSE Copyright 2008, Google Inc. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. Neither the name of Google Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Code generated by the Protocol Buffer compiler is owned by the owner of the input file used when generating it. This code is not standalone and requires a support library to be linked with it. This support library is itself covered by the above license.

16 INNOVATION AND INTEGRITY EROAD.COM