I NSTRUCTI ON M ANUAL Before commencing assembly, please read these instructions thoroughly. Ultimate EP (GM05) Specifications Wing Span: 3.5 in / 85 mm Wing Area: 357 sq in / 3 sq dm Flying Weight: 4 oz / 680 g Fuselage Length: 34 in / 870 mm Requires: 4-channel radio w/ 3 micro servos. Outrunner Motor KM083011 w/ Propeller Adaptor HW340100 0A Brushless ESC,3 cells 11.1V 1300 mah Li-Po battery & charger. Warning! This model is not a toy. It is designed for maximum performance. Please seek advice if one is not familiar with this kind of electric powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference. * Specifications are subject to change without notice.* THE WINGS MAKER FACTORY PRE-FABRICATED ALMOST-READY-TO-FLY (ARF) SERIES MADE IN CHINA www. thewingsmaker. com
Ultimate EP INDEX BEFORE YOU BEGIN PARTS LIST ASSEMBLY SAFETY PRECAUTIONS BEFORE YOU BEGIN P.1 P. P.3-P.10 P.10 1 3 Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer. For pre-assembled kits, please check proper functions of all servos on the ground before flying. Servo gears could be damaged when control surfaces are hit during transportation of models. The manufacturer will replace any servos due to manufacturer`s defect, but will not cover plane crashes due to damaged servos not detected before flying. Symbols used throughout this instruction manual comprise of the following :- Apply epoxy glue. Apply instant glue (C.A.glue, super glue.) Apply thread locker Must be purchased separately! Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. 3mm Peel off shaded portion covering film. Drill holes with the specified diameter (here: 3mm). Cut off shaded portion. Pierce the shaded portion covering film. Pay close attention here! Warning! Do not overlook this symbol! P.1
Parts List 1.MAIN WING -- 1 set PLYWOOD 6x1x4mm -- pcs FIBRE TAPE 17x380mm -- 4 pcs.ball JOINT CONTROL ARM PL403100 -- sets SCREW PM.5x1mm -- pcs WASHER d.5xd8mm -- pcs PUSHROD Ø1.4x9mm w/ Threads (For Aileron) -- pcs STRAPER PL411106 -- pcs FUEL TUBE dxd4x4mm -- pcs 3.FUSELAGE -- 1 set STABILIZER & ELEVATOR -- 1 set FIBRE TAPE 17x40mm -- 1 pc. 4.VERTICAL FIN & RUDDER -- 1 set FIBRE TAPE 17x15mm -- 1 pc. PLYWOOD 6x1x4mm -- pcs 5.TAIL LANDING GEAR PL3410030 --1 set SCREW PAx8mm -- pcs TAIL WHEEL Ø3mm PL351030 -- 1 pc. PLYWOOD 6x1x4mm -- pcs 6.MAIN LANDING GEAR -- 1 set COLLAR Ø.6mm w/ Set Screw -- sets PLYWOOD COLLAR Ø8xmm -- pcs MAIN WHEEL Ø40mm PL3116040 -- pcs SCREW PA.6x8mm -- 1 pc. PLYWOOD 6x0.4x.5mm (For Main Landing Gear) -- 1 pc. MAIN LANDING GEAR COVER -- 1 pair WHEEL PANT -- 1 pair P. MOUNTING PLATE PL411400 -- pcs SCREW PWAx6mm -- 4 pcs 7.CLEVIS PL411107 -- pcs HORN PL4113103 -- 1 pc. CARBON PUSHROD Ø1.5x70mm w/ Threads (For Elevator) -- 1 pc. 8.CLEVIS PL411107 -- pcs HORN PL4113103 -- 1 pc. CARBON PUSHROD Ø1.5x13mm w/ Threads (For Rudder) -- 1 pc. 9.SOCKET HEAD SCREW M3x6mm -- 4 pcs WASHER d3xd7mm -- 4 pcs SPINNER Ø36mm -- 1 set PROPELLER PL6314050 -- 1 set 10.CANOPY -- 1 pc. 11.SIDE CABANE -- pcs CENTER CABANE -- 1 pc. 1.CARBON PUSHROD Ø1.5x1mm w/ Threads (For Elevator) -- pcs CLEVIS PL411107 -- 4 pcs HORN PL4113103 -- 4 pcs 13.BATTERY COVER -- 1 pc. BATTERY TIE 160mm-- 1 pc. BATTERY MAT x50x150mm -- pcs DOUBLE-SIDED TAPE 30x35mm (For Brushless ESC) -- 1 pc. 14.DECALS: GM05 DEC -- 1 set
1 Main Wing Fibre Tape Bottom Upper Fibre Tape 17x380 mm Lower Plywood 6x1x4 mm Fibre Tape 17x380 mm Aileron Servo Lower Wing PM. 5 x 1mm Screw d.5xd8mm Washer TWM PL810010 CLEVIS WRENCH Straper Ball Joint Control Arm Fuel Tube dxd4x4mm Washer d.5xd8mm Pushrod Ø1.4x9mm PM.5x1mm P.3
3 Stabilizer & Elevator Joining surfaces should be clean and dry. Slightly roughen surfaces with sandpaper for best results. Bottom Fibre Tape Fibre Tape 17x40 mm 0 Vertical Fin & Rudder 4 Fibre Tape 17x15 mm Fibre Tape Plywood 6x1x4mm Joining surfaces should be clean and dry. Slightly roughen surfaces with sandpaper for best results. Completed 0 Tail Landing Gear 5 Plywood 6x1x4mm PAx8mm Screw PAx8mm Wheel Ø3mm Plastic Collar 1.mm P.4
90 6 Main Landing Gear PA.6x8mm Screw 1 PWAx6mm Screw 4 Landing Gear.6mm Collar w/ Set Screw 10 0 Fuselage Landing Gear Plywood 6x0.4x.5mm PA.6x8mm Landing Gear Covers PWAx6mm Mounting Plate 1x0mm M3x3mm Set Screw Plywood Collar Ø8xmm.6mm Collar Wheel Pants Wheel Ø40mm Completed Landing Gear 7 Elevator Pushrod Clevis Pushrod Ø1.5x63mm Clevis Pushrod Ø1.5x70mm Horn P.5
8 Rudder Pushrod Clevis Pushrod Ø1.5x15mm 90 Clevis Pushrod Ø1.5x13mm Horn 9 Outrunner Motor / Spinner Make sure rotating motor casing is not in contact with wirings or anything. M3x6mm Socket Head Screw 4 PMx1mm Screw PA1.7x8mm Screw d3xd7mm Washer 4 Optional Parts Outrunner Motor 8/ 30 KM083011 Propeller Adaptor (d3xd5) HW340100 M3x6mm d3xd7mm Washer Don't over-tighten the M3 screws, too much stress on the screws could split the firewall. 1 3 EZ Connector PMx1mm Brushless ESC PMx1mm ESC Solder Solder Motor TWM KP0011310 Don t over-tighten the PM screws, let the propeller blades align themselves when spinning. 9x6 Propeller PL6314050 4 5 PA1.7x8mm d6xd15mm Washer M5 Nut Ø36mm Spinner TWM HW3111700 PROPELLER ADAPTOR WRENCH Completed P.6
10 Canopy Canopy 11 Wing Setting Joining surfaces should be clean and dry. Slightly roughen surfaces with sandpaper for best results. Side Cabane Center Cabane A=A` B=B` C=C` A A` C B B` C` Completed P.7
1 Main Wing Main Wing (Upper) Horn Clevis Pushrod Ø1.5x1mm Horn Clevis Main Wing (Lower) 13 Radio Equipment Install and arrange the equipment as shown in the picture. Battery Tie Battery Receiver Battery Mat Battery Cover Completed P.8
14 Decals F5-L F0 F6 F1-L F-L F3-L F4-L W0 W1-L W1-R W-L W-R W3-L W4-L W4-R W3-R W5-L W5-R P.9
15 Control Throws Elevator 15mm 15mm Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. Rudder 5mm 5mm Ailerons 5mm 5mm 16 C.G. The ideal C.G. position is 77mm (3 in.) behind the leading edge center apex of the upper wing. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying. 77mm 3.03 in. C.G. http://www.thewingsmaker.com/instructionmanuals.php Warning! Important Safety Precautions # First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. # Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. Ultimate EP # is specially designed to be powered by KM083011 Outrunner Motor. # Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller. Extreme caution should be exercised when working with electric powered models. Make sure the propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental movement of the throttle stick will spin the propeller and could cause injuries. # Check and re-tighten up all factory assembled screws, use thread locker if necessary. P.10
www.thewingsmaker.com THE WINGS MAKER