Fig. 2110 www.pipingtech.com/fig2110 Sway Strut with 4 of Adjustment Engineered spring supports option 1 option 2 ORDERING: Specify size, figure number, description, nominal pipe size or special O.D. and C-to-C dimension. LOAD lb. ROD END EXT. PIECE PIPE A C - C W MIN. MAX. MIN. F D D1 N R S T A 650 3/4 1" 1 1/2 18 3/4 60 9 1/2 4 5/8 1 5/8 1 3/4 1/4 1 3/4 0.499 SCH.80 0.497 B 1,500 1 1 1/2" 2 3/8 20 1/2 108 10 5 1/4 2 1/4 2 7/8 3/8 1 1/8 1 1/8 0.749 SCH.40 0.747 C 4,500 1 2" 2 3/4 20 1/2 120 10 5 1/4 2 1/2 3 3/8 1/2 1 1/2 1 1/8 0.749 SCH.40 0.747 1 8,000 1 1/4 2" 3 3/4 24 120 10 1/2 6 3/4 3 4 3/8 3/4 1 3/4 1 3/8 0.999 SCH.160 0.997 2 11,630 1 1/2 2 1/2" 3 25 120 11 7 3 1/2 5 3/8 3/4 1 3/4 1 1/2 0.999 SCH.160 0.997 3 15,700 1 3/4 2 1/2" 5 5/16 25 1/2 120 11 1/2 7 5 7/16 4 11/16 1 2 1 13/16 1.249 SCH.160 1.247 4 20,700 2 3" 5 5/16 29 1/2 120 12 8 3/4 5 7/16 4 11/16 1 2 1/2 1 13/16 1.249 SCH.160 1.247 5 27,200 2 1/4 3" 6 32 1/2 120 13 9 3/4 5 9/16 6 1 1/4 2 1/2 2 1/8 1.499 SCH.160 1.497 6 33,500 2 1/2 4" 6 3/4 35 1/2 120 13 11 1/4 6 1/8 6 9/16 1 3/4 3 2 3/16 1.749 SCH.160 1.747 7 68,200 3 4" 6 38 1/2 120 14 12 1/4 7 1/8 5 3/4 2 3 1/2 2 3/8 1.999 SCH.160 1.997 8 120,000 4 6" 7 1/4 41 1/2 120 16 12 3/4 14 8 3/4 2 1/4 4 3/4 2 13/16 2.499 SCH.160 2.497 * Load must not be applied outside a 10 included angle to the pipe clamp axis. VLDEVICES.XLS-09/02/11 93
Engineered Spring supports Fig. 2120 www.pipingtech.com/fig2120 Mini Sway Strut ORDERING: Specify size, figure number, description, nominal pipe size or special O.D. and C-to-C dimension. LOAD ROD END EXT. PIECE PIPE A C-C (Style 1) C-C (Style 2) MIN. MAX. MIN. MAX. D D1 N R S T 94 A 650 3/4 1" 1 1/2 8 1/8 9 3/4 9 5/8 18 3/4 1 5/8 1 3/4 1/4 1 3/4 0.499 SCH.80 0.497 B 1,500 1 1 1/2" 2 3/8 9 3/4 11 1/2 11 1/2 20 1/2 2 1/4 2 7/8 3/8 1 1/8 1 1/8 0.749 SCH.40 0.747 C 4,500 1 2" 2 3/4 10 12 11 1/2 20 1/2 2 1/2 3 3/8 1/2 1 1/2 1 1/8 0.749 SCH.40 0.747 1 8,000 1 1/4 2" 3 3/4 11 1/8 13 1/4 13 1/8 24 3 4 3/8 3/4 1 3/4 1 3/8 0.999 SCH.160 0.997 2 11,630 1 1/2 2 1/2" 3 11 3/4 14 1/2 14 1/4 25 3 1/2 5 3/8 3/4 1 3/4 1 1/2 0.999 SCH.160 0.997 3 15,700 1 3/4 2 1/2" 5 5/16 13 3/8 16 15 7/8 25 1/2 5 7/16 4 11/16 1 2 1 13/16 1.249 SCH.160 1.247 4 20,700 2 3" 5 5/16 15 1/2 19 18 1/2 29 1/2 5 7/16 4 11/16 1 2 1/2 1 13/16 1.249 SCH.160 1.247 5 27,200 2 1/4 3" 6 16 7/8 20 1/2 20 3/8 32 1/2 5 9/16 6 1 1/4 2 1/2 2 1/8 1.499 SCH.160 1.497 6 33,500 2 1/2 4" 6 3/4 18 1/4 23 22 1/4 35 1/2 6 1/8 6 9/16 1 3/4 3 2 3/16 1.749 SCH.160 1.747 7 68,200 3 4" 6 20 24 24 38 1/2 7 1/8 5 3/4 2 3 1/2 2 3/8 1.999 SCH.160 1.997 * All struts provided with +/- 1" adjustment from specified C-C dimension VLDEVICES.XLS-09/17/09
Fig. 2110 & 2120 www.pipingtech.com/ssa-takeout Sway Strut Assemblies Engineered spring supports three bolt clamp for sway strut assemblies E-TAKEOUT FOR SWAY STRUT ASSEMBLIES PIPE A B C 1 2 3 4 5 6 7 3/4 2 7/16 1 2 9/16 1 1/4 2 11/16 1 1/2 4 1/8 4 1/8 2 5 1/8 5 1/8 2 1/2 5 3/8 5 3/8 3 5 15/16 5 15/16 4 6 1/2 6 1/2 8 5/8 10 1/8 12 1/4 13 1/2 16 1/4 5 7 7 9 7/16 10 15/16 12 13/16 14 5/16 16 13/16 6 8 9/16 8 9/16 9 15/16 11 7/16 13 5/16 14 13/16 17 5/16 18 9/16 20 5/16 8 9 9/16 9 9/16 10 1/8 12 7/16 14 9/16 15 13/16 18 5/16 20 1/16 21 5/16 10 10 5/8 10 5/8 11 3/8 13 3/4 15 5/8 16 7/8 19 7/8 21 1/8 22 3/8 12 11 5/8 11 5/8 12 9/16 14 3/4 16 5/8 18 3/8 20 7/8 22 1/8 23 3/8 14 12 11/16 12 11/16 13 1/2 13 1/2 17 1/4 19 21 1/2 22 3/4 24 1/2 30 16 13 11/16 13 11/16 14 7/8 14 7/8 18 3/4 20 22 1/2 23 3/4 25 1/2 31 18 14 11/16 14 11/16 16 1/4 16 1/4 16 1/4 21 23 1/2 25 1/4 27 32 20 15 7/8 15 7/8 15 7/8 17 1/4 17 1/4 22 24 1/2 26 1/4 28 33 1/2 24 17 7/8 17 7/8 17 7/8 19 5/16 19 5/16 19 5/16 27 28 3/4 30 36 30 23 3/8 23 3/8 23 3/8 28 1/4 28 1/4 28 1/4 30 1/2 31 3/4 33 39 36 28 3/4 28 3/4 28 3/4 28 3/4 34 3/4 34 3/4 34 3/4 34 3/4 36 42 VLDEVICES.XLS-09/02/11 95
Engineered Spring supports stock materials for pipe support assemblies 36 P-P Hydraulic Snubber for 128,000 lb. Load 76,800 lb. load big ton spring with PTFE, 25% glass filled slide plates 200-U Type Constant with Roller Guided Load Table 100 e-type constant spring support PTP 200-U Type Constants with Slide Plates for 109,000 lb. Load Custom Designed 100-E Constant rod and clevises 96 www.pipingtech.com/spring-supports
Support assembly Components Pipe Clamps & Risers - Saddle Supports Coverings - Hold Down Clamps Beam Attachments - Clevis Hangers - Hardware, Rods & U-Bolts http://www.pipingtech.com/support-component roller stands hold down clamps u-bolt cradle supports spider guide 97
DESCRIPTION PAGE Fig. 50: Light Two-Bolt Pipe Clamp... Fig. 60: Heavy Two-Bolt Pipe Clamp... Fig. 70: Light Three-Bolt Pipe Clamp... Fig. 70A: Alloy Light Three-Bolt Pipe Clamp... Fig. 80: Heavy Three-Bolt Pipe Clamp... Fig. 90: Riser Clamp... Fig. 190: Fabricated Riser Clamp... Chart C for Clamp Design... Fig. 2: Adjustable Band Hanger... Fig. 42: Yoke U-Bolt (Standard)... Fig. 43: Yoke U-Bolt (Heavy Duty)... Fig. 83: Adjustable Clevis Hanger... Fig. 89: Clevis Hanger for Insulated Lines... Fig. 195: Roller Hanger... Fig. 200: Trapeze Roller Hanger... Fig. 20: Welded Beam Attachment... Fig. 72: Welding Lug... Fig. 73: Concrete Clevis Plate... Fig. 74: Concrete Single Lug Plate... Fig. 75: Channel Assembly... Fig. 135: Malleable Beam Clamp... Fig. 140: Heavy Duty Beam Clamp... Fig. 270: Horizontal Travelers... Fig. 30: Turnbuckle... Fig. 35: Rod Coupling Straight with Sight Hole... Fig. 40: Weldless Eye Nut... Fig. 91: Clevis Pin with Cotters... Fig. 92: Steel Washer Plate... Fig. 95: Steel Clevis... Fig. 100: Long Tangent U-Bolt... Fig. 110: Welded Eye Rod... Fig. 120: Eye Rod (Not Welded)... Fig. 122: All-Threaded Eye Rod... Fig. 126: Welded Linked Eye Rod... Fig. 127: Linked Eye Rod... Fig. 128: Hanger Rod (Thread Both Ends R.H.)... Fig. 129: Hanger Rod (Thread One End R.H., One End L.H.)... Fig. 46: Adjustable Pipe Saddle Support... Fig. 48: Pipe Saddle Support with U-Bolt... Fig. 182: Non-Metallic Wear Pad... Fig. 183: Insulation Protection Shield... Fig. 184: Pipe Covering Saddle for 1 Insulation... Fig. 185: Pipe Covering Saddle for 1 1/2 Insulation... Fig. 186: Pipe Covering Saddle for 2 Insulation... Fig. 187: Pipe Covering Saddle for 2 1/2 Insulation... Fig. 188: Pipe Covering Saddle for 3 Insulation... Fig. 189: Pipe Covering Saddle for 4 Insulation... Fig. 210: Roller Chair... Fig. 215: Adjustable Pipe Roll Support... Fig. 230: Roller Stand... Fig. 240: Adjustable Roller Stand... Fig. 260: Adjustable Elbow Support... Fig. HD-1: Anchor Type Hold-Down for Pipe Line... Fig. HD-2: Hold-Down for Lateral Restraint... Fig. HD-3: Arrestor Type Hold-Down... 102 103 104 105 106 107 108 109 110 111 111 112 113 114 115 116 117 118 118 119 120 120 121 122 123 124 125 126 127 128 129 129 130 130 130 131 131 132 133 134 135 136 136 136 137 137 137 138 138 139 140 141 142 143 144 98 www.pipingtech.com/support-component
Fig. 50 - Page 102 Light Two-Bolt Pipe Clamp Fig. 80 - Page 106 Heavy Three-Bolt Pipe Clamp Fig. 60 - Page 103 Heavy Two-Bolt Pipe Clamp Fig. 90 - Page 107 Riser Clamp Fig. 70 - Page 104 Light Three-Bolt Pipe Clamp Fig. 190 - Page 108 Fabricated Riser Clamp Fig. 70A - Page 105 Alloy Light Three-Bolt Pipe Clamp Fig. 2 - Page 110 Adjustable Band Hanger Fig. 42-43 - Page 111 Yoke U-Bolt Fig. 83 - Page 112 Adjustable Clevis Hanger Fig. 89 - Page 113 Clevis Hanger for Insulated Lines Fig. 195 - Page 114 Roller Hanger Fig. 200 - Page 115 Trapeze Roller Hanger Fig. 20 - Page 116 Welded Beam Attachment Fig. 72 - Page 117 Welding Lug Fig. 73 - Page 118 Concrete Clevis Plate Fig. 74 - Page 118 Concrete Single Lug Plate Fig. 75 - Page 119 Channel Assembly Fig. 135 - Page 120 Malleable Beam Clamp Fig. 140 - Page 120 Heavy Duty Beam Clamp Fig. 270 - Page 121 Horizontal Travelers Fig. 30 - Page 122 Turnbuckle Fig. 35 - Page 123 Rod Coupling Fig. 40 - Page 124 Weldless Eye Nut www.pipingtech.com/support-component 99
Fig. 91 - Page 125 Clevis Pin with Cotters Fig. 110 - Page 129 Eye Rod (Welded) Fig. 92 - Page 126 Steel Washer Plate Fig. 120 - Page 129 Eye Rod (not welded) Fig. 95 - Page 127 Steel Clevis Fig. 122 - Page 130 All-Threaded Rod Fig. 100 - Page 128 Long Tangent U-Bolt Fig. 126 - Page 130 Linked Eye Rod (Welded) Fig. 127 - Page 130 Linked Eye Rod Fig. 128 - Page 131 Hanger Rod Fig. 129 - Page 131 Hanger Rod Fig. 46 - Page 132 Adjustable Pipe Saddle Support Fig. 48 - Page 133 Pipe Saddle Support with U-Bolt Fig. 182 - Page 134 Non-Metallic Wear Pad Fig. 183 - Page 135 Insulation Protection Shield Fig. 184-189 - Page 136 Pipe Covering Saddle Fig. 210 - Page 138 Roller Chair Fig. 215 - Page 138 Adjustable Pipe Roll Support Fig. 230 - Page 139 Roller Stand Fig. 240 - Page 140 Adjustable Roller Stand Fig. 260 - Page 141 Adjustable Elbow Support Fig. PTP HD-1 - Page 142 Hold Down (Anchor Type) Fig. PTP HD-2 - Page 143 Hold Down (Lateral Restraint) Fig. PTP HD-3 - Page 144 Hold Down (Arrestor Type) 100 www.pipingtech.com/support-component
Support Assembly components Piping Technology & Products, Inc. maintains an extensive inventory of components required for pipe hanger and support assemblies. Most of these are industry standards which have been used by piping designers for many years. One of the value-added services we provide is assembly and tagging of units before shipping so field crews can install them with minimal effort. Since we work with these materials daily, it is easier for us to do assemblies and verify components and dimensions than it is for a field crew, for whom installing pipe supports is only one of many tasks to be performed in a given work day. Many assemblies are attached to the pipe with clamps. Our inventories include all types of clamps made from carbon steel with galvanized and black finishes. We can fabricate clamps from alloy steels for high-temperature applications in which standard clamps are not adequate. When ordering your clamps, please add an A to the figure number of any items that you wish to be fabricated from our special alloy material. We have included a chart to help in the specification of special clamps for high-temperatures and heavy loads. To compensate for pipe movement, a designer may choose from a variety of clevis hangers, roller hangers, and adjustable bands to support the pipe. These are linked to the supporting structure with rods and other hardware components. Beam attachments and other accessories are attached to the supporting structure to complete the assembly. All of these components must be strong enough to support the loads in the environment where they are installed. Galvanized components are often used to resist corrosion. Saddle coverings are used with insulated pipes in order to provide protection to the insulation at points of support. Roller stands, elbow supports, and other items can be supplied in adjustable models which allow field crews to make easy installations. Hold-downs are special clamping supports used on pipes which are subject to large vibrations and stresses, such as those near compressors. The hold-downs dampen these forces by transferring them to the supporting structure, and thus protect the piping system. pipe saddles 30 galvanized riser clamp www.pipingtech.com/support-component 101
Fig. 50 www.pipingtech.com/fig50 Light Two-Bolt Pipe Clamp Size range: 1/2 thru 36 Material: Finish: Service: Ma x. Temp.: 750 F Ordering: Carbon steel Black or galvanized; furnished black unless otherwise specified. Recommended for suspension of cold pipe lines or hot lines where little or no insulation is required. Specify pipe size, figure number, description and finish. 102 PIPE MAX. RECOM. LOAD (lb.) STOCK @ 650 F @750 F B C D E F G H APPROX. WEIGHT (lb. per each) 1/2 500 445 1 1/2 1 17/32 1 5/16 1/8 x 1 1 17/32 0.29 3/4 500 445 1 1/8 1/2 1 21/32 1 1/8 5/16 1/8 x 1 1 21/32 0.33 1 500 445 1 1/8 1/2 1 29/32 1 3/8 5/16 1/8 x 1 1 21/32 0.35 1 1/4 500 445 1 7/16 1/2 1 31/32 1 7/16 5/16 1/8 x 1 1 31/32 0.37 1 1/2 800 715 1 9/16 1/2 2 5/32 1 5/8 5/16 1/8 x 1 2 3/32 0.43 2 1,040 930 2 1/8 1/2 2 3/4 2 1/8 1/2 1/4 x 1 2 3/4 1.10 2 1/2 1,040 930 2 1/2 5/8 3 1/4 2 5/8 1/2 1/4 x 1 3 1/8 1.20 3 1,040 930 2 13/16 5/8 3 9/16 2 15/16 1/2 1/4 x 1 3 7/16 1.40 3 1/2 1,040 930 3 1/8 5/8 3 13/16 3 3/16 1/2 1/4 x 1 3 3/4 1.50 4 1,040 930 3 7/16 3/4 4 3/8 3 5/8 5/8 1/4 x 1 1/4 4 3/16 2.30 5 1,040 930 4 3/4 4 15/16 4 3/16 5/8 1/4 x 1 1/4 4 3/4 2.60 6 1,615 1,440 4 7/8 7/8 5 7/8 5 3/4 3/8 x 1 1/2 5 3/4 5.40 8 1,615 1,440 6 1 7 6 1/8 3/4 3/8 x 1 1/2 6 7/8 6.50 10 2,490 2,220 7 5/16 1 8 9/16 7 7/16 7/8 1/2 x 2 8 7/16 13.60 12 2,490 2,220 8 1/4 1 9 9/16 8 7/16 7/8 1/2 x 2 9 3/8 15.20 14 2,490 2,220 9 1 1/8 10 5/8 9 1/4 7/8 1/2 x 2 1/2 10 3/8 20.50 16 2,490 2,220 10 1 1/8 11 5/8 10 1/4 7/8 1/2 x 2 1/2 11 3/8 22.30 18 3,060 2,730 11 1/2 1 1/4 13 11 5/8 1 5/8 x 2 1/2 12 7/8 31.60 20 3,060 2,730 12 1/2 1 3/8 14 1/8 12 3/4 1 1/8 5/8 x 2 1/2 13 7/8 35.80 24 3,060 2,730 15 1 5/8 16 7/8 15 1/4 1 1/4 5/8 x 3 16 5/8 53.10 30 3,500 3,360 18 1/4 2 21 1/4 19 1 3/4 3/4 x 4 20 5/8 113.90 36 4,000 3,570 22 1/2 2 1/2 25 1/2 23 2 1 x 5 25 219.00 SCOMPONENTS01.XLS-07/01/09
Fig. 60 www.pipingtech.com/fig60 Heavy Two-Bolt Pipe Clamp size range: 3 thru 36 finish: service: ma x. temp.: 750 F Carbon steel Black or galvanized; furnished black unless otherwise specified. Recommended for suspension of cold or hot pipe lines with heavy load having little or no insulation. Specify pipe size, figure number, description and finish. PIPE MAX. RECOM. LOAD (lb.) STOCK @ 650 F @750 F B C D E F G H K APPROX. WEIGHT (lb. per each) 3 3,370 3,005 2 15/16 1 4 3 1/8 3/4 5/16 x 2 3 13/16 5/8 3.60 3 1/2 3,370 3,005 3 1/4 1 4 1/4 3 3/8 3/4 5/16 x 2 3 13/16 5/8 3.90 4 3,515 3,135 3 9/16 1 4 7/8 3 3/4 7/8 3/8 x 2 4 11/16 5/8 5.50 5 3,515 3,135 4 1/8 1 5 1/2 4 3/8 7/8 3/8 x 2 5 1/4 5/8 6.30 6 4,865 4,340 5 1 1/8 6 5/8 5 1/4 1 1/2 x 2 1/2 6 3/8 7/8 11.70 8 4,865 4,340 6 1/8 1 1/8 7 5/8 6 1/4 1 1/2 x 2 1/2 7 1/2 7/8 13.90 10 6,010 5,360 7 9/16 1 1/4 9 1/16 7 11/16 1 1/4 5/8 x 2 1/2 8 5/16 7/8 22.30 12 8,675 7,740 9 1 5/8 10 7/8 9 1/4 1 1/2 3/4 x 3 10 5/8 7/8 38.10 14 9,120 8,135 9 3/4 1 5/8 11 7/8 10 1 1/2 3/4 x 4 11 5/8 7/8 46.80 16 9,120 8,135 10 3/4 1 5/8 12 7/8 11 1 1/2 3/4 x 4 12 5/8 7/8 51.40 18 13,800 12,305 14 1/2 3 17 1/4 14 1/2 2 3/4 x 6 17 1/4 3 130.10 20 15,300 13,645 16 3 18 3/4 16 2 1 x 5 18 3/4 3 163.60 24 16,300 14,535 18 1/2 3 1/4 21 1/2 18 1/2 2 1/4 1 x 6 21 1/2 3 1/4 215.00 28 18,000 16,055 20 1/2 3 1/4 23 1/2 20 1/2 2 1/4 1 x 8 23 1/2 3 1/4 303.00 30 20,500 18,285 22 1/2 3 1/2 26 22 1/2 2 1/2 1 1/4 x 7 26 3 1/2 365.40 32 23,750 21,180 23 1/2 3 1/2 27 23 1/2 2 1/2 1 1/4 x 8 27 3 1/2 432.00 34 25,000 22,295 25 3 1/2 28 1/2 25 2 1/2 1 1/2 x 8 28 1/2 3 1/2 534.00 36 28,000 24,975 26 1/2 3 1/2 30 1/4 26 1/2 2 3/4 1 1/2 x 8 33 3/4 3 1/2 575.00 SCOMPONENTS01.XLS-07/01/09 103
Fig. 70 www.pipingtech.com/fig70 Light Three-Bolt Pipe Clamp 104 Size range: 1/2 thru 36 Material: Finish: Service: Ma x. Temp.: 750 F Ordering: PIPE Carbon steel Black or galvanized; furnished black unless otherwise specified. Recommended for suspension of cold or hot pipe lines where little or no insulation is required. Specify pipe size, figure number, description and finish. MAX. RECOM. LOAD (lb.) @ 650 F @750 F B C D E F G H APPROX. WEIGHT (lb. per each) 1/2 950 850 15/16 5/16 2 7/8 2 7/16 3/8 3/16 x 1 1 3/8 0.66 3/4 950 850 15/16 5/8 2 7/8 2 7/16 3/8 3/16 x 1 1 3/8 0.70 1 950 850 1 1/16 5/8 3 2 9/16 3/8 3/16 x 1 1 1/2 0.76 1 1/4 950 850 1 1/4 5/8 3 1/8 2 11/16 3/8 3/16 x 1 1 11/16 0.81 1 1/2 1,545 1,380 1 13/16 1 1/16 4 7/8 4 1/8 5/8 1/4 x 1 1/4 2 3/8 2.30 2 1,545 1,380 2 1/8 1 1/16 5 7/8 5 1/8 5/8 1/4 x 1 1/4 2 11/16 2.60 2 1/2 1,545 1,380 2 5/16 1 1/16 6 1/8 5 3/8 5/8 1/4 x 1 1/4 2 15/16 2.70 3 1,545 1,380 2 3/4 1 1/16 6 11/16 5 15/16 5/8 1/4 x 1 1/4 3 1/2 3.00 4 2,500 2,230 3 3/8 1 1/16 7 5/8 6 1/2 3/4 5/16 x 2 4 1/2 6.70 5 2,500 2,230 3 15/16 1 1/16 8 1/8 7 3/4 5/16 x 2 5 7.00 6 2,865 2,555 4 3/4 1 7/16 9 11/16 8 9/16 7/8 3/8 x 2 1/2 6 1/8 11.50 8 2,865 2,555 5 3/4 1 7/16 10 11/16 9 9/16 7/8 3/8 x 2 1/2 7 1/8 13.20 10 3,240 2,890 6 7/8 1 7/16 12 10 5/8 1 1/2 x 2 1/2 8 1/4 19.80 12 3,240 2,890 7 7/8 1 7/16 13 11 5/8 1 1/2 x 2 1/2 9 1/4 22.30 14 4,300 3,835 9 1/16 2 14 5/16 12 11/16 1 1/4 5/8 x 3 10 11/16 37.70 16 4,300 3,835 10 1/16 2 15 5/16 13 11/16 1 1/4 5/8 x 3 11 11/16 41.40 18 4,300 3,835 11 1/16 2 16 5/16 14 11/16 1 1/4 5/8 x 3 12 11/16 44.90 20 4,500 4,015 12 3/8 2 17 5/8 15 7/8 1 1/2 3/4 x 3 14 57.30 24 4,500 4,015 14 3/8 2 19 5/8 17 7/8 1 1/2 3/4 x 3 16 65.90 28 6,000 5,340 17 1/2 2 1/4 24 1/4 21 3/4 1 1/2 3/4 x 4 20 112.30 30 7,500 6,675 18 1/2 2 1/2 26 1/8 23 3/8 1 1/2 3/4 x 5 21 1/4 150.00 36 10,500 9,345 22 1/2 3 32 1/4 28 3/4 1 3/4 1 x 5 26 257.50 SCOMPONENTS01.XLS-09/02/11
Fig. 70A www.pipingtech.com/fig70a Alloy Light Three-Bolt Pipe Clamp Size range: 1/2 thru 36 Material: Finish: Service: PIPE Chrome molybdenum steel (ASTM A387) Black Ma x. Temp.: 1050 F Ordering: Recommended for suspension of hot pipe lines requiring up to 4 of insulation. Specify pipe size, figure number, description and finish. MAX. RECOM. LOAD (lb.) @ 750 F @1000 F @1050 F B C D E F G H APPROX. WEIGHT (lb. per each) 1/2 860 610 455 15/16 5/16 2 7/8 2 7/16 3/8 3/16 x 1 1 3/8 0.66 3/4 860 610 455 15/16 5/8 2 7/8 2 7/16 3/8 3/16 x 1 1 3/8 0.70 1 860 610 455 1 1/16 5/8 3 2 9/16 3/8 3/16 x 1 1 1/2 0.76 1 1/4 860 610 455 1 1/4 5/8 3 1/8 2 11/16 3/8 3/16 x 1 1 11/16 0.81 1 1/2 1,410 1,000 745 1 13/16 1 1/16 4 7/8 4 1/8 5/8 1/4 x 1 1/4 2 3/8 2.30 2 1,410 1,000 745 2 1/8 1 1/16 5 7/8 5 1/8 5/8 1/4 x 1 1/4 2 11/16 2.60 2 1/2 1,410 1,000 745 2 5/16 1 1/16 6 1/8 5 3/8 5/8 1/4 x 1 1/4 2 15/16 2.70 3 1,410 1,000 745 2 3/4 1 1/16 6 11/16 5 15/16 5/8 1/4 x 1 1/4 3 1/2 3.00 4 2,290 1,625 1,200 3 3/8 1 1/16 7 5/8 6 1/2 3/4 5/16 x 2 4 1/2 6.70 5 2,290 1,625 1,200 3 15/16 1 1/16 8 1/8 7 3/4 5/16 x 2 5 7.00 6 2,620 1,860 1,380 4 3/4 1 7/16 9 11/16 8 9/16 7/8 3/8 x 2 1/2 6 1/8 11.50 8 2,620 1,860 1,380 5 3/4 1 7/16 10 11/16 9 9/16 7/8 3/8 x 2 1/2 7 1/8 13.20 10 2,970 2,100 1,565 6 7/8 1 7/16 12 10 7/16 1 1/2 x 2 1/2 8 1/4 19.80 12 2,970 2,095 1,555 7 7/8 1 7/16 13 11 7/16 1 1/2 x 2 1/2 9 1/4 22.30 14 3,915 2,795 2,060 9 1/16 2 14 5/16 12 11/16 1 1/4 5/8 x 3 10 11/16 37.70 16 3,915 2,795 2,060 10 1/16 2 15 5/16 13 11/16 1 1/4 5/8 x 3 11 11/16 41.40 18 3,915 2,795 2,060 11 1/16 2 16 5/16 14 11/16 1 1/4 5/8 x 3 12 11/16 44.90 20 4,995 3,550 2,635 12 3/8 2 17 5/8 15 7/8 1 1/2 3/4 x 3 14 57.30 24 4,995 3,550 2,635 14 3/8 2 19 5/8 17 7/8 1 1/2 3/4 x 3 16 65.90 28 5,475 3,890 2,900 17 1/2 2 1/4 24 1/4 21 3/4 1 1/2 3/4 x 4 20 112.30 30 6,850 4,860 3,630 18 1/2 2 1/2 26 1/8 23 3/8 1 1/2 3/4 x 5 21 1/4 150.00 36 9,580 6,800 5,070 22 1/2 3 32 1/4 28 3/4 1 3/4 1 x 5 26 257.50 SCOMPONENTS01.XLS-08/31/09 105
Fig. 80 www.pipingtech.com/fig80 Heavy Three-Bolt Pipe Clamp size range: 1 1/2 thru 36 finish: service: ma x. temp.: 750 F Carbon steel Black or galvanized; furnished black unless otherwise specified. Recommended for suspension of cold or hot pipe lines where little or no insulation is required. Specify pipe size, figure number, description and finish. PIPE MAX. RECOM. LOAD (lb.) @ 650 F @750 F B C D E F G H APPROX. WEIGHT (lb. per each) 1 1/2 2,710 2,420 2 1/8 1 5 13/16 5 3/4 3/8 x 2 3 1/8 5.50 2 2,710 2,420 3 1 6 1/16 5 1/16 3/4 3/8 x 2 4 5.70 3 2,710 2,420 3 5/8 1 1/2 8 6 1/2 3/4 3/8 x 2 5 1/8 7.50 4 3,500 3,125 4 1/2 1 3/4 9 7 7/8 3/8 x 2 1/2 6 1/2 10.70 6 3,500 3,125 4 3/4 1 3/4 10 3/16 8 15/16 1 3/8 x 2 1/2 6 12.00 8 4,800 4,285 6 2 11 3/8 10 1/8 1 1/8 1/2 x 2 1/2 7 1/4 18.50 10 5,500 4,910 7 1/4 2 1/4 13 1/8 11 3/8 1 1/4 1/2 x 3 1/2 9 30.30 12 7,000 6,250 8 5/8 2 1/2 14 5/16 12 9/16 1 3/8 5/8 x 3 1/2 10 3/8 42.00 14 9,500 8,485 9 5/8 2 1/2 15 1/2 13 1/2 1 1/2 3/4 x 4 11 5/8 60.00 16 10,000 8,930 10 7/8 3 17 1/8 14 7/8 1 3/4 3/4 x 4 1/2 13 1/8 80.00 18 13,800 12,325 12 1/2 3 1/2 18 1/4 16 1/4 2 1 x 4 14 1/2 115.00 20 15,300 13,665 13 1/2 3 1/2 19 3/4 17 1/4 2 1 x 5 16 140.00 24 16,300 14,555 15 1/2 3 1/2 22 5/16 19 5/16 2 1 x 6 18 1/2 190.00 28 18,000 16,055 18 7/8 4 31 3/4 27 1/4 2 1/4 1 x 7 23 3/8 354.00 30 20,500 18,285 19 7/8 4 1/4 32 3/4 28 1/4 2 1/4 1 x 8 24 3/8 406.00 36 28,000 24,975 24 5/8 4 1/2 40 1/4 34 3/4 2 3/4 1 1/2 x 8 30 1/8 678.00 SCOMPONENTS01.XLS-09/02/11 106
Fig. 90 www.pipingtech.com/fig90 Riser Clamp Size Range: 1/2 thru 24 finish: service: ma x. temp.: 650 F PIPE Carbon steel Black or galvanized; furnished black unless otherwise specified. For support and steadying of steel pipe risers either insulated or bare, cast iron pipe, or conduit. Specify pipe size, figure number, description and finish. MAX. RECOM. LOAD (lb.) APPROX. WEIGHT (lb. per 100) LENGTH A STOCK BOLT 1/2 255 123 9 3/8 3/16 x 1 1/4 3/8 x 1 1/2 3/4 255 136 9 3/8 3/16 x 1 1/4 3/8 x 1 1/2 1 255 138 9 5/8 3/16 x 1 1/4 3/8 x 1 1/2 1 1/4 390 195 10 1/4 x 1 1/4 3/8 x 1 1/2 1 1/2 390 201 10 3/8 1/4 x 1 1/4 3/8 x 1 1/2 2 390 217 10 3/4 1/4 x 1 1/4 7/16 x 2 2 1/2 390 229 11 1/4 1/4 x 1 1/4 7/16 x 2 3 530 250 12 1/4 x 1 1/4 7/16 x 2 3 1/2 670 330 13 1/4 x 1 1/2 1/2 x 2 4 810 342 13 1/2 1/4 x 1 1/2 1/2 x 2 5 1,160 493 14 1/2 1/4 x 2 1/2 x 2 6 1,570 526 15 1/2 1/4 x 2 1/2 x 2 8 2,500 986 18 1/2 3/8 x 2 5/8 x 2 1/2 10 2,500 1,112 20 3/4 3/8 x 2 5/8 x 2 1/2 12 2,700 1,662 22 3/4 1/2 x 2 5/8 x 3 14 2,700 1,925 24 1/2 x 2 5/8 x 3 16 2,900 3,250 26 5/8 x 2 1/2 3/4 x 3 1/2 18 2,900 3,375 28 5/8 x 2 1/2 3/4 x 3 1/2 20 2,900 3,500 30 5/8 x 2 1/2 3/4 x 3 1/2 24 3,200 5,070 36 5/8 x 3 7/8 x 3 1/2 SCOMPONENTS01.XLS-09/02/11 107
Fig. 190 Fabricated Riser Clamp www.pipingtech.com/fig190 Service: In situations where the use of a welded lug attachment would create an undesirable crushing effect on the pipe wall, this clamp can transfer the load from the pipe wall to the riser clamp by means of hold-down lugs welded to the pipe. Methods of selection: Ordering: Clamps may be furnished in either Carbon or Alloy steel with bolting to suit, using an allowable stress of 10,000 PSI. Temperature correction factors listed in CHART A are based on allowable stresses listed in MSS-SP-58. 1. Determine total load to be supported and service temperature of the piping system. 2. Refer to CHART A and determine the temperature correction factor for the clamp material being used. 3. Multiply total load by the correction factor to obtain a corrected load. 4. Refer to CHART C and locate the point determined by the intersection of the total load coordinate and the pipe size curve. Project this point horizontally until it intersects with the D dimension coordinate. Directly above this point is the required stock size. 5. The bolt diameter is obtained by using the uncorrected total load and referring to CHART B. Specify pipe outside diameter, total load, design temperature, material and dimension D or center to center of hanger rods. Note: Pipe clamp can be fabricated to any specified material. CHART A - STRESS-TEMPERATURE CORRECTION FACTORS MATERIAL SPECIFICATION DESIGN TEMPERATURE F ASTM GRADE 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 A36-0.8 0.83 0.89 1.06 - - - - - - - - A-387 11 0.66 0.66 0.66 0.66 0.69 0.76 0.91 1.53 - - - - A-387 22 0.66 0.66 0.66 0.66 0.69 0.76 0.91 1.28 1.72 2.38 - - A-240 304 0.94 0.95 0.96 0.97 0.99 1 1.02 1.02 1.11 1.21 1.45 1.81 CHART B - CLAMP SPACING AND BOLT S UNCORRECTED TOTAL LOAD (lb.) 3,400 4,700 6,200 8,000 10,000 12,000 16,000 19,000 25,000 32,000 40,000 55,000 67,000 82,000 96,000 118,000 135,000 154,000 BOLT - B BOLT - C SPACE - S 5/8 3/4 7/8 1 1 1/8 1 1/4 1 3/8 1 1/2 1 3/4 2 2 1/4 2 1/2 2 3/4 3 3 1/4 3 1/2 3 3/4 4 - - - 3/4 7/8 1 1 1 1/8 1 3/8 1 1/2 1 3/4 2 2 2 1/4 2 1/2 2 3/4 3 3 7/8 1 1 1/4 1 1/2 1 1/2 1 3/4 1 7/8 2 1/4 2 1/4 2 1/2 3 3 1/4 3 1/2 4 4 4 1/4 4 1/2 4 3/4 SCOMPONENTS01.XLS-07/01/09 108
www.pipingtech.com/support-component 109
Fig. 2 Adjustable Band Hanger www.pipingtech.com/fig2 Adjustable band hanger is formed in one piece. Adjustment: Finish: Ordering: This hanger provides for a vertical adjustment of 1 to 2 with the pipe and hanger in position. A temporary support is not required while adjustment is being made. Hangers can be furnished galvanized. Specify when ordering. Specify pipe size, figure number and description. PIPE A B C D E WGT. / C APPROX. MAX. RECOM. LOAD (lb.) 1/2 3/8 1 13/16 2 5/16 2 1/2 1 1/8 10 610 3/4 3/8 2 1/16 2 5/8 2 1/2 1 5/16 14 610 1 3/8 2 3/16 2 7/8 2 1/2 1 7/16 15 610 1 1/4 3/8 2 9/16 3 7/16 2 1/2 1 13/16 18 610 1 1/2 3/8 2 3/4 3 11/16 2 1/2 1 15/16 23 610 2 3/8 3 4 3/16 2 1/2 2 3/16 24 610 2 1/2 1/2 3 7/8 5 5/16 3 1/2 3 35 970 3 1/2 4 1/4 6 3 1/2 3 5/16 36 970 3 1/2 1/2 4 1/2 6 1/2 3 1/2 3 9/16 37 970 4 5/8 4 7/8 7 1/8 4 3 13/16 84 1,250 5 5/8 5 11/16 8 7/16 4 4 5/8 93 1,250 6 3/4 6 3/8 9 11/16 4 1/2 5 3/16 171 1,600 8 7/8 7 9/16 11 7/8 4 1/2 6 3/16 271 1,800 10 7/8 8 5/8 14 3/16 4 1/2 6 3/16 319 1,800 12 7/8 9 5/8 16 1/4 4 1/2 6 3/16 478 1,800 SCOMPONENTS02.XLS-12/29/09 110
Fig. 42 & 43 Yoke U-Bolt Yoke, load bolt and load distribution strap is chrome molybdenum steel. U-Bolt is stainless steel. service: ma x. temp.: 1100 F note: fig. 42 - STandard Recommended for suspension of high temperature piping requiring 4 to 6 of insulation. Fig. 42 - Specify pipe size, figure number and description. Fig. 43 - Specify nominal pipe size, figure number and description. Strap provided on Fig. 43 only. www.pipingtech.com/fig42 PIPE MAX. RECOM. LOAD (lb.) @ 950 F @1050 F @1100 F B C D E F G H 8 5/8-10 13/16 9,500 9,100 8,800 9 1/2 2 4 13 3/4 1 1/2 7/8 14 1/2 4,900 10 7/8-12 13/16 9,500 9,100 8,800 10 1/2 2 4 14 3/4 1 1/2 7/8 16 1/2 5,400 12 7/8-14 1/8 9,500 9,100 8,800 11 1/4 2 4 15 1/2 1 1/2 7/8 18 5,900 14 3/16-16 1/8 12,500 12,000 11,500 13 2 1/4 5 16 3/4 1 3/4 1 21 10,400 16 3/16-18 1/8 12,500 12,000 11,500 14 2 1/4 5 17 3/4 1 3/4 1 23 11,300 18 3/16-20 1/4 12,500 12,000 11,500 15 2 1/4 5 18 3/4 1 3/4 1 25 12,500 20 5/16-22 1/4 15,500 15,000 14,500 16 1/2 2 1/4 5 20 2 1 1/8 28 16,200 22 5/16-24 1/4 15,500 15,000 14,500 17 1/2 2 1/4 5 21 2 1 1/8 30 17,600 24 5/16-26 1/4 15,500 15,000 14,500 18 1/2 2 1/4 5 22 2 1 1/8 32 19,300 26 5/16-28 1/4 20,000 19,200 18,500 20 2 1/2 6 23 3/4 2 1/4 1 1/4 34 1/2 27,400 28 5/16-30 1/4 20,000 19,200 18,500 21 2 1/2 6 24 3/4 2 1/4 1 1/4 36 1/2 29,800 fig. 43 - heavy duty PIPE MAX. RECOM. LOAD (lb.) www.pipingtech.com/fig43 @ 950 F @1050 F @1100 F B C D E F G H APPROX. WEIGHT (lb. per 100) SCOMPONENTS02.XLS-07/01/09 APPROX. WEIGHT (lb. per 100) 8 5/8-10 13/16 13,500 12,000 11,500 10 1/4 2 1/4 5 14 1 3/4 1 15 1/4 7,200 10 7/8-12 13/16 16,500 15,000 14,500 11 3/4 2 1/4 5 15 1/4 2 1 1/8 17 3/4 10,300 12 7/8-14 1/8 16,500 15,000 14,500 12 1/2 2 1/4 5 16 2 1 1/8 19 1/4 11,000 14 3/16-16 1/8 20,000 19,200 18,500 13 3/4 2 1/2 6 17 1/2 2 1/4 1 1/4 22 16,700 16 3/16-18 1/8 20,000 19,200 18,500 14 3/4 2 1/2 6 18 1/2 2 1/4 1 1/4 24 18,000 18 3/16-20 1/4 23,700 22,700 21,900 16 2 3/4 6 1/2 20 2 1/2 1 3/8 26 1/2 22,800 20 5/16-22 1/4 23,700 22,700 21,900 17 2 3/4 6 1/2 21 2 1/2 1 3/8 28 1/2 24,600 22 5/16-24 1/4 29,000 28,000 27,000 18 1/2 3 7 22 3/4 2 3/4 1 1/2 30 3/4 32,500 24 5/16-26 1/4 29,000 28,000 27,000 19 1/2 3 7 23 3/4 2 3/4 1 1/2 32 3/4 34,000 26 5/16-28 1/4 29,000 28,000 27,000 20 1/2 3 7 24 3/4 2 3/4 1 1/2 34 3/4 35,500 28 5/16-30 1/4 29,000 28,000 27,000 21 1/2 3 7 25 3/4 2 3/4 1 1/2 36 3/4 36,900 36 29,000 28,000 27,000 24 1/2 3 7 28 1/2 2 3/4 1 1/2 43 1/4 42,000 SCOMPONENTS02.XLS-09/17/09 111
Fig. 83 www.pipingtech.com/fig83 size: 1/2 thru 30 finish: service: Carbon steel ma x. temp.: 650 F features: components: installation: ordering: Black or galvanized; furnished black unless otherwise specified. Recommended for the suspension of noninsulated, stationary pipe lines. Designed with the yoke on outside of lower U-Strap so the yoke cannot slide toward the center of the bolt, thus bending of the bolt is minimized. Spacer sleeve used for size 16 thru 36. Top yoke, bottom strap, and bolt or stud with nut-assembled. Hanger load nut ABOVE clevis must be tightened securely to assure proper hanger performance. Specify pipe size, figure number, description and finish. Adjustable Clevis Hanger note: Punched forming holes may be present on certain sizes of this clevis hanger. These holes are solely for the purpose of manufacturing and do not affect the structural integrity or load carrying capacities of these hangers. PIPE MAX. RECOM. LOAD (lb.) APPROX. WEIGHT (lb. per 100) UPPER OF STEEL LOWER ADJUST. A B C D E F G 1/2 730 34 1/8 x 1 1/8 x 1 3/8 1 11/16 2 1/8 2 1/2 7/8 7/16 1/4 3/4 730 39 1/8 x 1 1/8 x 1 3/8 1 7/8 2 7/16 2 1/2 1 1/2 1/4 1 730 44 1/8 x 1 1/8 x 1 3/8 2 1/8 2 13/16 2 1/2 1 1/4 5/8 1/4 1 1/4 730 45 1/8 x 1 1/8 x 1 3/8 2 9/16 3 7/16 2 1/2 1 3/4 7/8 1/4 1 1/2 730 55 1/8 x 1 1/8 x 1 3/8 3 4 2 1/2 2 1/8 1 1/16 1/4 2 730 61 1/8 x 1 1/8 x 1 3/8 3 11/16 4 7/8 2 1/2 2 15/16 1 5/8 1/4 2 1/2 1,350 140 3/16 x 1 1/4 3/16 x 1 1/4 1/2 4 11/16 6 1/8 3 3 13/16 2 3/8 3 1,350 152 3/16 x 1 1/4 3/16 x 1 1/4 1/2 4 3/4 6 9/16 3 3 7/8 1 3/4 3/8 3 1/2 1,350 170 3/16 x 1 1/4 3/16 x 1 1/4 1/2 4 15/16 6 15/16 3 4 1/16 1 3/4 3/8 4 1,430 213 1/4 x 1 1/4 3/16 x 1 1/4 5/8 5 9/16 7 13/16 3 1/2 4 1/2 1 15/16 3/8 5 1,430 244 1/4 x 1 1/4 3/16 x 1 1/4 5/8 6 3/16 9 3 1/2 5 1/8 1 3/4 1/2 6 1,940 357 1/4 x 1 1/2 3/16 x 1 1/2 3/4 6 15/16 10 1/8 4 5 5/8 1 7/8 1/2 8 2,000 497 1/4 x 1 3/4 3/16 x 1 3/4 7/8 8 3/8 12 5/8 4 1/4 7 2 1/8 5/8 10 3,600 880 3/8 x 1 3/4 1/4 x 1 3/4 7/8 9 7/8 15 1/4 4 1/2 8 3/8 2 1/4 3/4 12 3,800 1,142 3/8 x 2 1/4 x 2 7/8 11 1/2 18 4 1/2 10 3/16 3 3/4 14 4,200 1,484 1/2 x 2 1/4 x 2 1 12 7/16 19 7/16 5 1/4 10 13/16 2 15/16 7/8 16 4,600 2,104 1/2 x 2 1/2 1/4 x 2 1/2 1 14 1/16 22 1/16 6 12 7/16 2 5/8 1 18 4,800 2,442 1/2 x 2 1/2 1/4 x 2 1/2 1 15 1/2 24 3/4 6 1/2 13 15/16 3 7/8 1 1/8 20 4,800 4,265 3/4 x 3 3/8 x 3 1 1/4 17 1/4 27 3/8 7 14 7/16 4 1 1/4 24 4,800 4,853 3/4 x 3 3/8 x 3 1 1/4 19 5/8 31 5/8 7 1/2 17 1/2 4 1/4 1 1/4 30 6,000 6,964 1 x 3 3/8 x 3 1 1/4 24 1/8 39 1/8 8 1/4 21 7/8 5 1 1/4 36-7,716 1 x 3 3/8 x 3 1 1/4 27 1/8 46 3/16 8 1/4 25 1/2 5 1/2 1 1/4 SCOMPONENTS02.XLS-09/17/09 112
Fig. 89 www.pipingtech.com/fig89 finish: Carbon steel Black Clevis Hanger for Insulated Lines function: approvals: components: ordering: PIPE MAX. RECOM. LOAD (lb.) Equivalent to Fig. 83, except bottom has been lengthened to allow covering without interfering with the bolt. Conforms to Federal Specification WW-H- 171-E, Type 1 and Manufacturers Standardization Society SP-69, Type 1 Top yoke, bottom strap, and bolt or stud with nut-assembled. Specify pipe size, figure number, description and finish. APPROX. WEIGHT (lb. per 100) UPPER OF STEEL LOWER ADJUST. A B C D E F G H 1/2 730 44 1/8 x 1 1/8 x 1 3/8 3 5/8 4 3/16 2 1/2 2 7/8 1/2 1/4 2 3/4 730 51 1/8 x 1 1/8 x 1 3/8 3 5/8 4 1/4 2 1/2 2 7/8 1/2 1/4 2 1 730 58 1/8 x 1 1/8 x 1 3/8 4 4 11/16 2 1/2 3 1/4 5/8 1/4 2 1 1/4 730 64 1/8 x 1 1/8 x 1 3/8 4 7/16 5 1/4 2 1/2 3 5/8 7/8 1/4 2 1 1/2 730 72 1/8 x 1 1/8 x 1 3/8 4 3/4 5 3/4 2 1/2 4 1/16 1 1/16 1/4 2 2 730 85 1/8 x 1 1/8 x 1 3/8 7 7/16 8 11/16 2 1/2 6 1/2 1 5/8 1/4 4 2 1/2 1,350 191 3/16 x 1 1/4 3/16 x 1 1/4 1/2 8 7/16 9 15/16 3 7 1/2 2 3/8 4 3 1,350 201 3/16 x 1 1/4 3/16 x 1 1/4 1/2 8 5/8 10 5/16 3 7 9/16 1 3/4 3/8 4 3 1/2 1,350 210 3/16 x 1 1/4 3/16 x 1 1/4 1/2 8 11/16 10 3/4 3 7 3/4 1 3/4 3/8 4 4 1,430 247 1/4 x 1 1/4 3/16 x 1 1/4 5/8 9 3/8 11 5/8 3 1/2 8 3/16 1 15/16 3/8 4 5 1,430 309 1/4 x 1 1/4 3/16 x 1 1/4 5/8 9 7/8 12 5/8 3 1/2 8 3/4 1 3/4 1/2 4 6 1,940 337 1/4 x 1 1/2 3/16 x 1 1/2 3/4 10 5/8 14 4 9 3/8 1 7/8 1/2 4 8 2,000 673 1/4 x 1 3/4 3/16 x 1 3/4 7/8 12 3/8 16 3/4 4 1/4 11 2 5/8 4 10 3,600 1,102 3/8 x 1 3/4 1/4 x 1 3/4 7/8 13 3/4 19 3/16 4 1/2 12 1/4 2 1/8 3/4 4 12 3,800 1,382 3/8 x 2 1/4 x 2 7/8 15 1/8 21 9/16 4 1/2 13 5/8 2 7/16 3/4 4 SCOMPONENTS02.XLS-07/01/09 113
Fig. 195 www.pipingtech.com/fig195 Roller Hanger Service: How to Size: Cast iron roll, carbon steel yoke, roll rod, and hex nuts. For suspension of pipe from a single rod where horizontal movement may occur because of expansion or contraction. If the roll is to support bare pipe, select the size directly from the nominal pipe size (see table below). Specify pipe size, figure number, description and finish. PIPE MAX. O.D. OF COVERING MAX. RECOM. LOAD (lb.) APPROX. WEIGHT (lb. per 100) A B C D E F G H 2 1/2 3 225 170 1/2 5 3/4 3 1/4 1 15/16 2 7/8 1/2 3/16 x 1 1 11/16 3 3 5/8 310 220 1/2 6 3/8 3 7/8 2 1/4 3 1/8 1/2 1/4 x 1 1 5/8 3 1/2 4 1/8 390 253 1/2 7 4 3/8 2 9/16 3 1/2 1/2 1/4 x 1 1/4 1 11/16 4 4 11/16 475 321 5/8 7 9/16 4 15/16 2 13/16 3 5/8 1/2 1/4 x 1 1/2 1 5/8 5 5 3/4 685 627 5/8 9 1/8 6 3 7/16 4 1/2 5/8 3/8 x 1 3/4 1 15/16 6 6 7/8 780 927 3/4 10 5/16 7 1/8 4 5 3/4 3/8 x 2 1 7/8 8 9 780 1,454 7/8 12 11/16 9 1/4 5 1/8 6 1/8 7/8 3/8 x 2 1/2 2 10 11 965 1,880 7/8 15 1/16 11 1/4 6 3/8 7 1/4 7/8 3/8 x 2 1/2 2 1/16 12 13 1,200 2,774 7/8 17 7/16 13 1/4 7 7/16 8 3/8 1 1/2 x 2 1/2 2 1/4 14 14 1/4 1,200 3,913 1 18 7/8 14 1/2 8 3/8 8 3/4 1 1/8 1/2 x 2 1/2 2 16 16 1/4 1,200 4,905 1 20 13/16 16 1/2 9 3/8 9 11/16 1 1/4 1/2 x 2 1/2 1 15/16 18 18 1/4 1,400 5,780 1 1/8 23 3/4 18 1/2 10 7/16 11 7/16 1 1/4 1/2 x 3 2 11/16 114 20 20 1/4 1,600 7,594 1 1/4 26 20 1/2 11 5/8 12 1/4 1 3/8 5/8 x 3 2 1/2 SCOMPONENTS02.XLS-07/01/09
Fig. 200 www.pipingtech.com/fig200 service: adjustment: Cast iron roll and sockets; steel roll rod. Trapeze Roller Hanger For suspension of pipe from two rods where longitudinal movement due to expansion or contraction may occur. Adjustment socket permits vertical adjustment at the roll. how to size: 1. If the roll is to support non-insulated pipe, select the size directly from nominal pipe size. 2. If used with pipe covering protection saddle, see Pages 136-137 for size of pipe roll. 3. If roll is to support covered pipe, select the nominal pipe size (column 1) which corresponds to the O.D. of covering and saddle (column 2). Specify nominal pipe size, figure number, description and finish. NOMINAL MAX. O.D. OF ADJUSTED MAX. RECOM. APPROX. WEIGHT PIPE COVERING SOCKET NO. SAFE LOAD (lb.) (lb. per 100) A B C D E F G H J 1 2 1-3/8 600 45 4 1/8 3 1 1/2 1 3/4 3/8 3/8 1 1/16 9/16 1 1/4 2 1/2 1-3/8 600 48 4 1/2 3 3/8 1 7/8 1 1/16 3/4 3/8 3/8 1 1/4 9/16 1 1/2 2 3/4 1-3/8 600 51 4 3/4 3 5/8 2 1/8 1 1/8 3/4 3/8 3/8 1 3/8 9/16 2 3 1/4 1-3/8 600 57 5 1/4 4 1/8 2 5/8 1 3/16 3/4 3/8 3/8 1 5/8 9/16 2 1/2 3 3/4 2-1/2 660 100 6 1/4 4 7/8 3 1/8 1 3/8 7/8 1/2 1/2 1 15/16 11/16 3 4 1/2 2-1/2 700 110 6 7/8 5 1/2 3 3/4 1 7/16 7/8 1/2 1/2 2 1/4 11/16 3 1/2 5 2-1/2 750 135 7 1/2 6 1/8 4 1/4 1 5/8 1 1/2 1/2 2 9/16 3/4 3-1/2 150 7 3/4 6 1/4 5/8 3/4 4 5 1/2 2-1/2 750 150 8 6 5/8 4 3/4 1 3/4 1 1/2 1/2 2 13/16 3/4 3-1/2 165 8 1/4 6 3/4 5/8 3/4 5 7 2-5/8 750 226 9 7/16 8 1/16 5 13/16 2 1 1/8 5/8 1/2 3 7/16 13/16 3-5/8 257 9 11/16 5/8 7/8 6 8 1/4 2-3/4 1,070 378 10 15/16 9 9/16 6 7/8 2 5/16 1 1/4 3/4 1/2 4 7/8 3-3/4 416 11 3/16 5/8 1 4-3/4 445 11 7/16 3/4 1 8 10 1/2 2-7/8 1,350 585 13 5/16 11 15/16 8 7/8 2 13/16 1 1/2 7/8 1/2 5 1/8 15/16 3-7/8 625 13 9/16 5/8 1 1/16 4-7/8 690 13 13/16 3/4 1 3/16 5-7/8 715 14 1/16 7/8 1 1/8 10 12 3/4 2-7/8 1,730 838 15 7/16 14 1/16 11 3 3/8 1 3/4 7/8 1/2 6 3/8 15/16 3-7/8 862 15 11/16 5/8 1 1/16 4-7/8 920 15 15/16 3/4 1 3/16 5-7/8 950 16 3/16 7/8 1 1/8 12 14 3/4 3-1 2,400 1,465 17 7/16 15 13/16 12 1/2 3 7/8 2 1 5/8 7 7/16 1 1/8 4-1 1,525 17 11/16 3/4 1 1/4 5-1 1,590 17 15/16 7/8 1 1/4 14 16 1/4 5-1 1/8 3,130 2,360 19 7/8 17 3/4 14 1/4 4 5/8 2 1/2 1 1/8 7/8 8 3/8 1 7/16 6-1 1/8 2,425 20 1/8 1 1 3/8 16 18 5-1 1/4 3,970 3,080 21 7/8 19 3/4 16 1/4 5 2 5/8 1 1/4 7/8 9 7/16 1 1/2 6-1 1/4 3,185 22 1/8 1 1 1/2 7-1 1/4 3,260 22 3/8 1 1/8 1 1/2 18 20 1/4 5-1 1/4 4,200 3,370 24 21 7/8 18 1/4 5 7/16 2 3/4 1 1/4 7/8 10 1/2 1 1/2 6-1 1/4 3,475 24 1/4 1 1 1/2 7-1 1/4 3,550 24 1/2 1 1/8 1 1/2 20 22 1/2 8-1 3/8 4,550 4,700 27 1/4 24 1/4 20 1/4 6 3 1 1/4 1 1/4 11 5/8 1 5/8 24 26 1/2 6-1 1/2 6,160 7,255 31 28 5/8 24 1/4 7 3/16 3 5/8 1 1/2 1 14 1 13/16 7-1 1/2 7,365 31 1/4 1 1/8 1 15/16 8-1 1/2 7,500 31 5/8 1 1/4 2 1/16 9-1 1/2 7,630 32 1/8 1 1/2 1 3/4 30 32 1/2 8-1 7/8 7,290 12,690 38 1/2 35 1/2 30 1/4 8 15/16 4 1/2 1 3/4 1 1/4 17 7/16 2 1/4 9-1 7/8 12,990 39 1 1/2 2 7/16 10-1 7/8 13,400 39 7/8 1 7/8 2 1/8 SCOMPONENTS02.XLS-08/31/09 115
Fig. 20 www.pipingtech.com/fig20 Carbon steel Welded Beam Attachment Specify rod size, figure number, description and finish. Steel attachment for welding to bottom flange or structural members which will accommodate eye rods or lug attachments. This unit permits rod swing, thereby making it suitable for pipes with horizontal movement. NOTE: For rod sizes 1 1/8 and above, pins are used in lieu of bolts. NO. ROD MAX. RECOM. A LOAD (lb.) B C D E F W BOLT/PIN WEIGHT (lb. per 100) 3 3/8 730 1/4 1 1/4 2 7/8 2 7/8 2 1/2 x 2 1/2 121 4 1/2 1,350 1/4 1 1/4 2 7/8 2 7/8 2 5/8 x 2 1/2 130 5 5/8 2,160 1/4 1 1/4 2 7/8 2 7/8 2 3/4 x 3 160 6 3/4 3,230 3/8 1 1/2 3 1/8 2 1 1/8 2 1/2 7/8 x 3 1/2 280 7 7/8 4,480 3/8 2 4 1/4 3 1 1/4 2 1/2 1 x 4 390 8 1 5,900 1/2 2 4 1/2 3 1 1/2 3 1 1/8 x 4 1/2 630 9 1 1/8 6,200 1/2 2 1/4 4 3/4 3 1 3/4 3 1 1/4 x 4 1/2 630 10 1 1/4 9,500 5/8 2 1/2 5 3 2 4 1 3/8 x 5 1,021 12 1 1/2 13,800 3/4 3 6 1/2 4 2 1/2 5 1 5/8 x 5 3/4 1,900 14 1 3/4 18,600 3/4 3 3/4 7 3/4 5 2 3/4 5 1 7/8 x 6 7/8 2,425 16 2 24,600 3/4 3 3/4 8 1/4 5 3 1/4 6 2 1/4 x 6 7/8 3,060 18 2 1/4 32,300 3/4 4 1/4 9 1/2 6 3 1/2 6 2 1/2 x 7 3/8 3,688 20 2 1/2 39,800 3/4 4 1/2 9 3/4 6 3 3/4 6 2 3/4 x 7 5/8 3,924 22 2 3/4 49,400 5/8 3 3/4 9 3/4 5 3/4 4 6 3 x 7 4,080 24 3 60,100 5/8 3 3/4 10 1/4 6 1/4 4 7 3 1/4 x 7 4,670 SCOMPONENTS03.XLS-09/02/11 116
Fig. 72 Welding Lug www.pipingtech.com/fig72 Carbon steel Specify rod size, figure number, description and finish. ROD A B C H T MAX.LOAD (lb.) 1/2 1 1/2 1 1/4 2 1/2 11/16 1/4 1,350 5/8 1 1/2 1 1/4 2 1/2 13/16 1/4 2,160 3/4 1 1/2 1 1/4 2 1/2 15/16 3/8 3,230 7/8 2 1 1/4 2 1/2 1 1/8 3/8 4,480 1 2 1 1/2 3 1 1/4 1/2 5,900 1 1/8 3 1 1/2 3 1 3/8 1/2 6,230 1 1/4 3 2 4 1 1/2 5/8 9,500 1 1/2 3 2 1/2 5 1 3/4 3/4 13,800 1 3/4 3 2 1/2 5 2 3/4 18,600 2 4 3 6 2 3/8 3/4 24,600 2 1/4 4 1/2 3 6 2 5/8 3/4 32,300 2 1/2 4 1/2 4 8 2 7/8 1 39,800 2 3/4 4 1/2 4 8 3 1/8 1 49,400 3 5 4 8 3 3/8 1 60,100 SCOMPONENTS03.XLS-07/01/09 117
Fig. 73 www.pipingtech.com/fig73 ROD Fig. 74 Carbon steel size: Rod sizes 3/8 thru 2 finish: service: MAX. RECOM. LOAD (lb.) www.pipingtech.com/fig74 Concrete Clevis Plate A B C D F G H R S T U W 3/8 730 1 8 10 5 9/16 3/8 2 7/8 1 1/4 1/4 1/2 2 11.8 1/2 1,350 1 8 10 5 9/16 3/8 2 7/8 1 1/4 1/4 5/8 2 11.9 5/8 2,160 1 8 10 5 9/16 1/2 2 1 1 1/4 1/4 3/4 2 15.7 3/4 3,230 1 8 10 5 11/16 1/2 2 1 1/8 1 1/2 3/8 7/8 2 1/2 16.9 7/8 4,480 1 8 10 5 11/16 1/2 3 1 1/4 2 3/8 1 2 1/2 18.1 1 5,900 2 8 12 6 13/16 3/4 3 1 1/2 2 1/2 1 1/8 3 36.9 1 1/4 9,500 2 8 12 6 15/16 3/4 3 2 2 1/2 5/8 1 3/8 4 40.9 1 1/2 13,800 2 8 12 6 1 1/8 1 4 2 1/2 3 3/4 1 5/8 5 59.8 1 3/4 18,600 2 10 14 7 1 3/8 1 1/4 5 2 3/4 3 3/4 3/4 1 7/8 5 93.6 2 20,700 2 10 14 7 1 3/8 1 1/4 5 3 1/4 3 3/4 3/4 2 1/4 6 100.0 Black or galvanized; furnished black unless otherwise specified. Attachment for concrete ceiling. Specify rod size, figure number, description and finish. Carbon steel size: Rod sizes 1/2 thru 2 finish: Black or galvanized; furnished black unless otherwise specified. service: Structural attachment for concrete ceiling. Lug is used in conjunction with Fig. 95 (Forged Steel Clevis). Specify rod size, figure number, description and finish. Concrete Single Lug Plate APPROX. WEIGHT (lb. per each) SCOMPONENTS03.XLS-07/01/09 ROD MAX. RECOM. LOAD (lb.) A B C D E F G H R S T U W 1/2 1,350 1 8 10 5 4 7/8 9/16 3/8 1 1/2 1 1/4 1/4 1/4 5/8 2 1/2 11.1 5/8 2,160 1 8 10 5 4 7/8 9/16 1/2 1 1/2 1 1/4 1/4 1/4 3/4 2 1/2 14.6 3/4 3,230 1 8 10 5 4 13/16 11/16 1/2 1 1/2 1 1/4 3/8 3/8 7/8 2 1/2 14.8 7/8 4,480 1 8 10 5 4 13/16 11/16 3/4 2 1 1/4 3/8 3/8 1 2 1/2 22.0 1 5,900 2 8 12 6 5 3/4 13/16 3/4 2 1 1/2 1/2 1/2 1 1/8 3 31.9 1 1/4 9,500 2 8 12 6 5 11/16 15/16 1 3 2 5/8 5/8 1 3/8 4 43.8 1 1/2 13,800 2 8 12 6 5 5/8 1 1/8 1 3 2 1/2 3/4 3/4 1 5/8 5 45.6 1 3/4 18,600 2 8 12 6 5 5/8 1 3/8 1 1/4 3 2 1/2 3/4 3/4 1 7/8 5 55.7 APPROX. WEIGHT (lb. per each) 2 24,600 2 8 12 6 5 5/8 1 3/8 1 1/4 4 3 3/4 3/4 2 1/4 6 58.2 SCOMPONENTS03.XLS-07/01/09 118
Fig. 75 www.pipingtech.com/fig75 Channel Assembly Specify rod size, figure number, channel size, C-to-C and E dimension and material required. E = C-to-C + 2L + W ROD 3/8 1/2 5/8 3/4 7/8 1 1 1/8 1 1/4 1 1/2 1 3/4 2 2 1/4 2 1/2 2 3/4 3 3 1/4 3 1/2 H-HOLE 1/2 5/8 3/4 7/8 1 1 1/4 1 3/8 1 1/2 1 3/4 2 2 1/4 2 1/2 2 3/4 3 3 1/4 3 1/2 3 3/4 S 9/16 11/16 13/16 15/16 1 1/16 1 3/8 1 1/2 1 5/8 1 7/8 2 1/4 2 1/2 2 3/4 3 3 1/4 3 1/2 3 3/4 4 W 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 6 7 T 1/4 1/4 3/8 3/8 1/2 1/2 1/2 1/2 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 L 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 1/4 3/8 3/8 3/8 SAFE LOAD TABLE NOMINAL WEIGHT PER FT. 2C'S C-TO-C = SPAN IN INCHES 12 14 16 18 20 22 24 26 28 30 36 42 48 54 60 MAXIMUM SAFE LOAD IN KIPS 3 8.2 8.8 7.5 6.6 5.8 5.2 4.8 4.4 3.9 3.6 3.5 2.9 2.5 2.2 1.9 1.7 4 10.8 15.2 13.1 11.4 10.2 9.1 8.3 7.5 7.0 6.5 6.1 5.1 4.3 3.8 3.3 3.0 5 13.4 24.0 20.6 18.0 16.0 14.4 13.1 12.0 11.1 10.3 9.6 8.0 6.8 6.0 5.3 4.8 6 21.0 40.0 34.3 30.0 26.6 24.0 21.8 20.0 18.4 17.1 16.0 13.3 11.4 10.0 8.8 8.0 8 23.0 64.8 55.5 48.6 43.2 38.8 35.3 32.3 29.8 27.7 25.8 21.5 18.5 16.1 14.3 12.9 10 30.6 107.2 91.7 80.3 71.4 64.2 58.4 53.5 49.4 45.8 42.8 35.7 30.6 26.7 23.8 21.4 12 41.4 171.0 147.0 128.0 114.0 103.0 93.4 85.6 79.0 73.3 68.4 57.0 48.9 42.8 38.0 34.2 15 67.8 333.0 286.0 250.0 222.0 200.0 182.0 167.0 154.0 143.0 133.0 111.0 95.3 83.4 74.1 66.7 SCOMPONENTS03.XLS-09/17/09 119
Fig. 135 Malleable Beam Clamp www.pipingtech.com/fig135 finish: service: MAXIMUM ROD Malleable iron Black Recommended for attachment to structural steel. Use in conjunction with American Standard I-Beams and wide flange beams where beam widths are from a min. of 2 3/8 to a max. of 7 and flange thickness does not exceed 0.60. Specify figure number and description. BOLT DIA. ROD TAKE OUT (E) - FOR WIDTH OF BEAM FLANGE 2 3/8 3 4 5 6 7 MAX. RECOM. LOAD (lb.) APPROX. WEIGHT (lb. per each) 7/8 7/16 3 1/2 3 7/16 3 5/16 2 15/16 2 9/16 1 7/8 1,365 2.2 SCOMPONENTS03.XLS-07/01/09 Fig. 140 www.pipingtech.com/fig140 finish: service: Carbon steel Painted, shop primed or galvanized. For suspension of heavy loads from standard I-Beams and wide flange beams with flange widths to 15 and flange thickness to 1.07. Specify rod size, figure number, description, clamp size, beam size and finish. Heavy Duty Beam Clamp CLAMP E F MAX. LOAD (lb.) APPROX. WEIGHT (lb. per each) THK. MAXIMUM FLANGE WIDTH 1 1 0.375 11,500 9 1.07 10 2 1 0.375 11,500 11 1.07 15 SCOMPONENTS03.XLS-07/01/09 120
Fig. 270 Horizontal Travelers www.pipingtech.com/fig270 size range: installation: Available in four sizes to take loads up to 20,700 lb. All sizes provide for 12 of horizontal travel. Shipped ready for installation. Attach to the supporting steel by welding around the frame. Spring hanger may be bolted or welded to the load plate. features: Highly economical Minimum friction Virtually dust proof Compact - designed for minimum head room Versatile Specify size number, figure number, description and H dimensions if required. Horizontal travelers can be designed for special loads, travels or dual directional travel upon request. NO. MAX. RECOM. LOAD (lb.) APPROX. WEIGHT (lb. each) A B C D H MAX. L T W 1 3,770 15 2 1/2 1 5/8 5 3/8 2 1/2 1 1/8 15 1/8 3/4 4 5/8 2 6,230 37 3 1/2 2 5/8 7 7/8 3 1/2 1 3/8 16 3/8 3/4 6 3/4 3 11,630 69 5 3 10 1/2 5 1 3/4 17 7/8 1 9 3/4 4 20,700 102 6 3 1/2 12 1/2 6 2 1/2 19 1/8 1 1/2 10 1/4 SCOMPONENTS03.XLS-07/01/09 121
Fig. 30 Turnbuckle www.pipingtech.com/fig30 Material: Finish: Service: Ordering: Carbon steel Black or galvanized, furnished black unless otherwise specified. Provides adjustment up to 6 for heavy loads. Specify rod size, figure number, description and finish. We may supply fabricated or forged. fabricated Forged ROD A MAX. RECOM. LOAD (lb.) @ 650 F @750 F S T WEIGHT (lb. per 100) 3/8 730 572 7 1/4 5/8 34 1/2 1,350 1,057 7 1/2 3/4 47 5/8 2,160 1,692 7 3/4 7/8 86 3/4 3,230 2,530 8 1/4 1 1/8 134 7/8 4,480 3,508 8 1/2 1 1/4 190 1 5,900 4,620 9 1 1/2 247 1 1/8 7,660 5,560 9 1/4 1 5/8 338 1 1/4 9,500 7,440 9 1/4 1 5/8 330 1 1/2 13,800 10,807 9 3/4 1 7/8 530 1 3/4 18,600 14,566 10 1/2 2 1/4 780 2 24,600 19,265 11 2 1/2 1,195 2 1/4 32,300 25,295 12 1/4 3 1/8 2,700 2 1/2 39,800 31,169 12 1/4 3 1/8 2,690 SCOMPONENTS04.XLS-09/02/11 122
Fig. 35 www.pipingtech.com/fig35 Rod Coupling Straight with sight hole Material: Finish: Service: Ordering: Carbon Steel Black Used for connecting two rods together of the same diameter. Specify rod size, figure number, and description. ROD A MAX. LOAD (lb.) WEIGHT (lb.) D L 3/8 730 0.09 5/8 1 3/4 1/2 1,350 0.12 3/4 1 1/2 5/8 2,160 0.24 15/16 1 7/8 3/4 3,230 0.42 1 1/8 2 1/4 7/8 4,480 0.66 1 5/16 2 5/8 1 5,900 1.00 1 1/2 3 SCOMPONENTS04.XLS-08/12/09 123
Fig. 40 www.pipingtech.com/fig40 Weldless Eye Nut Forged steel service: For use on high temperature piping installations. features: Supports loads equal to the full limitation of the hanger rod. Provides flexible connection when used with straight thread rods. Specify rod size, figure number, description, rod tapping and finish. NO. ROD A MAX. RECOM. LOAD (lb.) @ 650 F @750 F B C D E F G APPROX. WEIGHT (lb. per 100) 1 3/8 730 572 1 1/2 1 3/16 1/2 2 1 3/8 11/16 68 1/2 1,350 1,057 69 5/8 2,160 1,692 66 3/4 3,230 2,530 59 2 7/8 4,480 3,508 2 1 11/16 3/4 2 5/8 1 15/16 1 170 1 5,900 4,620 170 3 1 1/8 7,660 5,560 2 1/2 1 13/16 1 3 3/8 2 3/8 1 1/4 380 1 1/4 9,500 7,440 380 1 1/2 13,800 10,807 350 4 1 3/4 18,600 14,566 4 4 1 1/2 6 1/4 4 2 1/4 1890 2 24,600 19,265 1890 2 1/4 32,300 25,295 1800 2 1/2 39,800 31,169 1660 SCOMPONENTS04.XLS-09/02/11 124
Fig. 91 www.pipingtech.com/fig91 Clevis Pin with Cotters Material: Finish: Service: Ordering: PIN DIA. D Carbon Steel Black or galvanized. To be used as an option to support the load on Type C variable spring hangers, Type C constant supports, Fig. 95 clevises, and Fig. 20 welded beam attachments. Specify pin diameter, figure number, description, finish, and if cotter pins are needed. If planning to use the clevis pin with any of the above mentioned figures, please list which figure in the order instructions. MAX. LOAD (lb.) @ 650 F @750 F WEIGHT (lb.) L W E H COTTER PIN 1/2 730 572 0.12 2 7/8 2 1/8 3/8 3/32 1/8 x 1 1/4 5/8 1,350 1,057 0.18 3 1/8 2 3/8 3/8 3/32 1/8 x 1 1/4 3/4 2,160 1,691 0.29 3 5/8 2 7/8 3/8 7/32 3/16 x 1 1/2 7/8 3,230 2,529 0.47 4 3 1/4 3/8 7/32 3/16 x 1 1/2 1 4,480 3,508 0.67 4 3 1/4 3/8 7/32 3/16 x 2 1 1/8 5,900 4,620 1.00 4 3/4 4 3/8 7/32 3/16 x 2 1 1/4 7,410 5,802 1.70 4 7/8 4 1/4 3/8 9/32 1/4 x 2 1 3/8 9,500 7,439 2.10 5 3/8 4 3/8 1/2 9/32 1/4 x 2 1 5/8 13,800 10,805 3.30 6 5 1/2 9/32 1/4 x 2 1 7/8 18,600 14,564 4.80 7 1/8 5 7/8 5/8 3/8 3/8 x 3 2 1/4 24,600 19,262 7.20 7 1/8 5 7/8 5/8 3/8 3/8 x 4 2 1/2 32,300 25,291 9.30 7 5/8 6 3/8 5/8 3/8 3/8 x 4 2 3/4 39,800 31,163 12.50 7 7/8 6 5/8 5/8 3/8 3/8 x 4 3 49,400 38,680 16.60 8 1/4 6 3/4 3/4 1/2 1/2 x 5 3 1/4 60,100 47,058 20.00 8 1/2 7 3/4 1/2 1/2 x 5 3 1/2 71,900 56,298 23.90 8 3/4 7 1/4 3/4 1/2 1/2 x 5 3 3/4 84,700 66,320 25.10 9 1/2 8 3/4 1/2 1/2 x 6 4 98,500 77,125 34.80 9 3/4 8 1/4 3/4 1/2 1/2 x 6 SCOMPONENTS04.XLS-09/02/11 125
Fig. 92 www.pipingtech.com/fig92 finish: service: Carbon steel Black For use on top of channels or angles to support pipe with rods or U-Bolts Specify rod size, figure number, description and finish. Steel Washer Plate ROD HOLE DIAMETER OF STEEL A x A x B APPROX. WEIGHT (lb. per 100) 3/8 1/2 3 x 3 x 1/4 6.20 1/2 5/8 3 x 3 x 1/4 6.20 5/8 3/4 3 x 3 x 3/8 9.10 3/4 7/8 4 x 4 x 3/8 16.00 7/8 1 4 x 4 x 1/2 22.00 1 1 1/4 4 x 4 x 1/2 21.00 1 1/4 1 1/2 5 x 5 x 1/2 33.00 1 1/2 1 3/4 5 x 5 x 3/4 48.00 1 3/4 2 5 x 5 x 3/4 47.00 2 2 1/4 5 x 5 x 3/4 45.00 2 1/4 2 1/2 6 x 6 x 3/4 66.00 2 1/2 2 3/4 6 x 6 x 3/4 64.00 2 3/4 3 6 x 6 x 3/4 62.00 3 3 1/4 6 x 6 x 3/4 59.00 3 1/4 3 1/2 6 x 6 x 3/4 56.00 3 1/2 3 3/4 7 x 7 x 3/4 81.00 3 3/4 4 7 x 7 x 3/4 78.00 SCOMPONENTS04.XLS-09/02/11 126
Fig. 95 www.pipingtech.com/fig95 service: Carbon steel Steel Clevis For use on high temperature piping installations. features: Complies fully with the code for pressure piping. Supports loads equal to the full limitation of the hanger rod. Specify body size, figure number, description, rod tapping, size of pin hole, size of pin, size of grip and finish. We may supply fabricated or forged. fabricated forged ROD MAX. RECOM. LOAD (lb.) PIN APPROX. WEIGHT BODY (lb. per each) NO. @ 650 F @750 F P A D N T W MAX. GRIP 3/8 730 572 1.0 2 1/2 3 7/8 1 7/16 5/8 5/16 1 1/16 5/8 1/2 1,350 1,057 0.9 5/8 3 7/8 1 7/16 5/8 5/16 1 1/16 5/8 5/8 2,160 1,692 0.9 3/4 3 7/8 1 7/16 5/8 5/16 1 1/16 5/8 3/4 3,230 2,530 2.5 2 1/2 7/8 4 2 1/2 1 1/8 5/16 1 1/4 7/8 7/8 4,480 3,508 2.5 1 4 2 1/2 1 1/8 5/16 1 1/4 7/8 1 5,900 4,620 4.0 3 1 1/8 5 3 1 5/16 1/2 1 1/2 1 1/4 1 1/8 7,600 4,620 4.0 1 1/4 5 3 1 5/16 1/2 1 1/2 1 1/4 1 1/4 9,500 7,440 4.0 1 3/8 5 3 1 5/16 1/2 1 1/2 1 1/4 1 1/2 13,800 10,807 6.0 3 1/2 1 5/8 6 3 1/2 1 5/8 1/2 1 3/4 1 1/2 1 3/4 18,600 14,566 8.0 4 1 7/8 6 4 1 3/4 1/2 2 1 1/2 2 24,600 19,265 16.0 5 2 1/4 7 5 2 1/4 5/8 2 1/2 2 1/2 2 1/4 32,300 25,295 26.0 6 2 1/2 8 6 2 3/4 3/4 3 2 1/2 2 1/2 39,800 31,169 26.0 2 3/4 8 6 2 3/4 3/4 3 2 1/2 SCOMPONENTS04.XLS-09/02/11 127
Fig. 100 www.pipingtech.com/fig100 Material: Finish: Ordering: PIPE Carbon steel Black. Galvanized upon request. Specify pipe size, figure number, description and finish, if other than black. Note: U-Bolts are furnished with four hexagon nuts or are furnished with two hexagon nuts. Special U-Bolts with longer tangents and threads and special materials can be furnished as specified. MAX. RECOM. LOAD (lb.) A Long Tangent U-Bolt B C D E WEIGHT (lb. per 100) 1/2 580 1/4 7/8 1 1/8 2 1/2 2 1/2 12 3/4 580 1/4 1 1/8 1 3/8 2 5/8 2 1/2 13 1 580 1/4 1 3/8 1 5/8 2 3/4 2 1/2 14 1 1/4 1,460 3/8 1 3/4 2 1/8 2 7/8 2 1/2 38 1 1/2 1,460 3/8 2 2 3/8 3 2 1/2 39 2 1,460 3/8 2 1/2 2 7/8 3 1/4 2 1/2 42 2 1/2 2,700 1/2 3 3 1/2 3 3/4 3 90 3 2,700 1/2 3 5/8 4 1/8 4 3 99 3 1/2 2,700 1/2 4 1/8 4 5/8 4 1/4 3 109 4 2,700 1/2 4 5/8 5 1/8 4 1/2 3 115 5 2,700 1/2 5 5/8 6 1/8 5 3 128 6 4,320 5/8 6 3/4 7 3/8 6 1/8 3 3/4 239 8 4,320 5/8 8 3/4 9 3/8 7 1/8 3 3/4 283 10 6,460 3/4 10 7/8 11 5/8 8 3/8 4 479 12 9,960 7/8 12 7/8 13 3/4 9 5/8 4 1/4 764 14 9,960 7/8 14 1/8 15 10 1/4 4 1/4 820 16 9,960 7/8 16 1/8 17 11 1/4 4 1/4 870 18 11,800 1 18 1/8 19 1/8 12 5/8 4 3/4 1,350 20 11,800 1 20 1/8 21 1/8 13 5/8 4 3/4 1,460 24 11,800 1 24 1/8 25 1/8 15 5/8 4 3/4 1,710 30 11,800 1 30 1/8 31 1/8 18 5/8 4 3/4 1,920 36 11,800 1 36 1/8 37 1/8 21 5/8 4 3/4 2,326 SCOMPONENTS04.XLS-07/01/09 128
Fig. 110 www.pipingtech.com/fig110 Eye Rod (Welded) ROD STANDARD ROD THREAD LENGTH (in.) MAX. RECOM. LOAD (lb.) A D @ 650 F @750 F 3/8 2 1/2 730 572 1/2 2 1/2 1,350 1,057 5/8 2 1/2 2,160 1,692 3/4 3 3,230 2,530 7/8 3 1/2 4,480 3,508 1 4 5,900 4,620 1 1/8 4 1/2 6,230 5,560 1 1/4 5 9,500 7,440 1 1/2 6 13,800 10,807 1 3/4 7 18,600 14,566 2 8 24,600 19,265 2 1/4 9 32,300 25,295 2 1/2 10 39,800 31,169 SCOMPONENTS04.XLS-07/01/09 size range: features: ma x. temp.: 750 F Welded eye rods are furnished in any length specified. Eye rods will be furnished in other than standard lengths and with other than standard length thread when required and so ordered. Carbon steel Through 1 1/2, inside diameter of eye will accommodate a bolt diameter 1/8 larger than rod diameter, 1 3/4 and larger inside diameter of eye will take a bolt of 1/4 larger than rod diameter. Specify rod length and diameter, figure number, description and finish. Fig. 120 www.pipingtech.com/fig120 Eye Rod (not welded) ROD STANDARD ROD MAX. RECOM. LOAD THREAD LENGTH (in.) (lb.) A D 3/8 2 1/2 240 1/2 2 1/2 440 5/8 2 1/2 705 3/4 3 1,050 7/8 3 1/2 1,470 1 4 1,940 1 1/8 4 1/2 2,430 1 1/4 5 3,120 1 1/2 6 4,650 1 3/4 7 6,380 2 8 8,280 2 1/4 9 10,900 2 1/2 10 13,400 SCOMPONENTS04.XLS-07/01/09 size range: features: ma x. temp.: 650 F Not welded eye rods are stocked in all sizes in the following standard lengths: 8, 10, 12, 14, 18, 24, 30, 36, 42, 48, 54, 60, 66 and 72. Eye rods will be furnished in other than standard lengths and with other than standard length thread when so ordered. Carbon steel For 1 1/2 rod, the inside eye diameter will accommodate a bolt with a diameter 1/8 larger than the rod diameter. For 1 3/4 or larger rods, the inside eye diameter will accomodate a bolt with a diameter of 1/4 larger than rod diameter. Specify rod length and diameter, figure number, description and finish. 129
Fig. 122 www.pipingtech.com/fig122 finish: service: ROD A Fig. 126 & 127 Carbon steel Black, painted, or hot dipped galvanized. MAX. RECOM. LOAD (lb.) All-Threaded Rod For use as support rods where a universal connection is required to allow piping movement. Specify rod length and diameter, figure number, description and finish. APPROX. WEIGHT (lb. per 100) @ 650 F @750 F 1/4 240 215 12 3/8 730 572 30 1/2 1,350 1,057 53 5/8 2,160 1,692 84 3/4 3,230 2,530 123 7/8 4,480 3,508 168 1 5,900 4,620 224 SCOMPONENTS04.XLS-09/02/11 Linked Eye Rod www.pipingtech.com/fig126-127 Carbon steel finish: Black, painted, or hot dipped galvanized. service: For use as support rods where a universal connection is required to allow piping movement. Specify rod size and length, thread length, figure number, description and finish. ROD THREAD fig. 126 fig. 127 LENGTH (in.) MAX. RECOM. LOAD (welded) A D FIG. 126 FIG. 127 3/8 2 1/2 730 240 1/2 2 1/2 1,350 440 5/8 2 1/2 2,160 705 3/4 3 3,230 1,050 7/8 3 1/2 4,480 1,470 1 4 5,900 1,940 1 1/8 4 1/2 6,230 2,430 1 1/4 5 9,500 3,120 1 1/2 6 13,800 4,650 1 3/4 7 18,600 6,380 2 8 24,600 8,280 2 1/4 9 32,300 10,900 2 1/2 10 39,800 13,400 SCOMPONENTS04.XLS-07/01/09 130
Fig. 128 & 129 www.pipingtech.com/fig128-129 Hanger Rod finish: size range: Carbon steel Black or hot dipped galvanized. FIG. 128 and 129 hanger rods are both ends and standard lengths of 8, 10, 12, 14, 18, 24, 30, 36, 42, 48, 54, 60, 66 and 72. Hanger rods are available in sizes other than standard lengths or standard thread lengths. Specify rod size and length, thread length, figure number, description and finish. fig. 128 - hanger rod both ends r.h. thread fig. 129 - hanger rod one end r.h. and other end l.h. ROD STANDARD ROD THD. LENGTH MAX. RECOM. LOAD (lb.) A D @ 650 F @750 F APPROX. WEIGHT (lb. per 100) 1/4 2 1/2 240 215 17 3/8 2 1/2 730 572 38 1/2 2 1/2 1,350 1,057 67 5/8 2 1/2 2,160 1,692 104 3/4 3 3,230 2,530 150 7/8 3 1/2 4,480 3,508 204 1 4 5,900 4,620 267 1 1/8 4 1/2 6,230 5,560 338 1 1/4 5 9,500 7,440 417 1 1/2 6 13,800 10,807 600 1 3/4 7 18,600 14,566 818 2 8 24,600 19,265 1068 2 1/4 9 32,300 25,295 1352 2 1/2 10 39,800 31,169 1669 SCOMPONENTS04.XLS-07/01/09 131
Fig. 46 www.pipingtech.com/fig46 Adjustable Pipe Saddle Support service: installation: Carbon steel saddle, locknut nipple, and special cast iron reducer, assembled. Base is not included - supplied as extra. Stanchion type support where vertical adjustment is required. Adjustment is obtained by turning the locknut nipple, the lower end of the nipple, and coupling during adjustment. Specify pipe size, figure number, description and finish. PIPE APPROX. WEIGHT (lb. per 100) A B C D E COMPLETE SADDLE ONLY SQUARE MIN. MAX. 2 1/2 900 480 2 1/2 3 1/2 9 1 1/2 8 13 3 920 500 2 1/2 3 3/4 9 1 1/2 8 1/4 13 1/4 3 1/2 940 520 2 1/2 4 9 1 1/2 8 1/2 13 1/2 4 1,500 760 3 4 1/4 9 2 1/2 9 1/4 14 5 1,665 925 3 4 7/8 9 2 1/2 10 14 3/4 6 1,765 1,025 3 5 1/2 9 2 1/2 10 1/2 15 1/4 8 2,020 1,280 3 6 7/8 9 2 1/2 11 3/4 16 1/2 10 2,515 1,775 3 8 1/2 9 2 1/2 13 1/2 18 1/4 12 2,900 2,160 3 9 15/16 9 2 1/2 15 19 3/4 14 4,920 3,800 4 10 15/16 11 3 16 1/4 20 3/4 16 5,320 4,200 4 12 3/8 11 3 17 3/4 22 1/4 18 7,080 5,100 6 13 7/8 13 1/2 3 1/2 19 1/2 24 20 10,480 8,500 6 15 3/8 13 1/2 3 1/2 21 25 1/2 24 13,000 11,000 6 17 15/16 13 1/2 4 23 3/4 28 1/4 30 17,000 15,000 6 21 5/16 13 1/2 4 27 31 1/2 32 18,100 16,100 6 22 1/2 13 1/2 4 28 1/4 32 3/4 36 24,900 22,900 6 24 1/2 13 1/2 4 30 1/4 34 3/4 SCOMPONENTS05.XLS-08/31/09 132
Fig. 48 Pipe Saddle Support with U-Bolt www.pipingtech.com/fig48 Carbon steel stanchion saddle with steel U-Bolt and nuts. installation: 1. Slip saddle base into riser pipe. 2. If riser pipe and flange are used, flange is drilled for bolting to steel beam or floor. 3. Yoke is attached to saddle after pipe is in place. Specify pipe size, figure number, description, material and finish. PIPE APPROX. WEIGHT (lb. per 100) A B 4 1,075 3 4 3/16 5 1,210 3 4 13/16 6 1,270 3 5 7/16 8 2,130 3 6 15/16 10 2,570 3 8 7/16 12 3,120 3 9 15/16 14 5,000 4 10 15/16 16 5,700 4 12 3/8 18 6,400 4 13 7/8 20 11,350 6 15 3/8 24 13,700 6 17 15/16 30 14,650 6 19 1/8 32 17,400 8 21 5/16 36 26,800 8 24 1/2 SCOMPONENTS05.XLS-09/02/11 133
Fig. 182 www.pipingtech.com/fig182 Non-Metallic Wear Pad Material: Finish: As is Size Range: 1/2 thru 48 Service: Ma x. Temp.: Ordering: Vinyl Resins Recommended to protect uninsulated pipe from the metal supporting structure. Pad to be secured to pipe using epoxy adhesive. 400 F Specify pipe size, figure number, description, length and angle. PIPE THICKNESS LENGTH L ANGLE A RADIUS R 1/2 1/4 12 90 7/16 3/4 1/4 12 90 9/16 1 1/4 12 90 5/8 1 1/4 1/4 12 90 7/8 1 1/2 1/4 12 90 1 2 1/4 12 90 1 3/16 2 1/2 1/4 12 90 1 7/16 3 1/4 12 90 1 13/16 3 1/2 1/4 12 90 1 3/4 4 1/4 12 90 2 1/4 5 1/4 12 90 2 13/16 6 1/4 12 60 3 5/16 8 1/4 12 60 4 5/16 10 1/4 12 60 5 3/8 12 1/4 12 30 6 3/8 14 1/4 12 30 7 16 1/4 12 30 8 18 1/4 12 30 9 20 1/4 12 30 10 24 1/4 12 30 12 26-48 3/8 12 30 1/2 of Pipe OD SCOMPONENTS05.XLS-11/13/09 134
Fig. 183 www.pipingtech.com/fig183 finish: size range: service: approvals: PIPE Carbon steel Galvanized and black. For use with 1/2 thru 24 pipe with insulation thickness 1/2, 3/4, 1, 1 1/2 and 2. Recommended for outside of foam or fiber glass insulation to preclude crushing of insulation without breaking the vapor barrier. Complies with Federal Specification WW-H-171E (Type 41) and Manufacturers Standardization Society SP-69 (Type 40). Specify pipe size, figure number, description, insulation thickness and finish. Shield Size Selection Table INSULATION THICKNESS (in.) 1/2 3/4 1 1-1/2 2 1/2 1A 1A - - - 3/4 1A 1A 2A 4A 6A 1 1A 2A 3A 5A 7A 1 1/4 2A 3A 3A 6A 7A 1 1/2 2A 3A 4A 6A 7A 2 3A 4A 5A 7A 8A 2 1/2 4A 5A 6A 7A 8A 3 5A 6A 7A 8A 9A 3 1/2 - - 8A 9A 10A 4 - - 8A 9A 10A 5 - - 9B 10B 11B 6 - - 10B 11B 12B 8 - - - 13C 14C 10 - - 14C 15C 16C 12 - - 16C 17C 18C 14 - - 17C 18C 19C 16 - - 19C 20C 21C 18 - - 21C 22C 23C 20 - - 23C 24C 25C 24 - - 26C 27C 28C Insulation Protection Shield SHIELD STOCK (GAGE) APPROX. WEIGHT EACH SHIELD DIMENSION LENGTH L RADIUS R X1A 18 0.54 12 0.95 1A 18 0.69 12 1.19 2A 18 0.84 12 1.44 3A 18 0.99 12 1.75 4A 18 1.10 12 2.00 5A 18 1.30 12 2.25 6A 18 1.40 12 2.50 7A 18 1.60 12 2.78 8A 16 1.90 12 3.32 9A 16 2.70 12 3.82 10A 16 3.10 12 4.32 9B 16 4.00 18 3.82 10B 16 4.60 18 4.32 11B 16 5.10 18 4.82 12B 16 5.60 18 5.38 13C 14 10.20 24 5.88 14C 14 11.10 24 6.38 15C 14 11.90 24 7.00 16C 14 12.70 24 7.50 17C 14 13.60 24 8.00 18C 14 14.50 24 8.50 19C 12 21.20 24 9.00 20C 12 22.40 24 9.50 21C 12 23.60 24 10.00 22C 12 24.80 24 10.50 23C 12 25.90 24 11.00 24C 12 27.10 24 11.50 25C 12 28.30 24 12.00 26C 12 31.00 24 13.00 27C 12 31.80 24 13.50 28C 12 33.00 24 14.00 SCOMPONENTS05.XLS-09/02/11 135
Fig. 184, 185 & 186 www.pipingtech.com/fig184-186 finish: service: note: PIPE Black, galvanized or painted. Designed to keep insulation from crushing and to reduce heat losses. Specify pipe size, figure number, description, insulation thickness and finish. All saddles are 12 long with the side edges turned up. Fig. 184-1 insulation MAX. RECOM. LOAD APPROX. WEIGHT (lb. per 100) COVERING THK. 3/4 1,200 141 7/8 1 9/16 1 1,200 141 1 1/16 1 7/8 1 1/4 1,200 141 7/8 1 7/8 1 1/2 1,200 151 1 2 1/8 2 1,200 167 1 1/16 2 3/8 2 1/2 1,200 167 1 1/16 2 5/8 3 1,200 188 1 2 15/16 3 1/2 1,200 228 1 1/4 3 7/16 4 1,200 228 1 1/16 3 7/16 5 1,200 228 1 3 15/16 6 1,800 378 1 4 1/2 SCOMPONENTS05.XLS-10/27/11 Pipe Covering Saddle C PIPE Fig. 185-1 1/2 insulation MAX. RECOM. LOAD APPROX. WEIGHT (lb. per 100) COVERING THK. 3/4 1,200 210 1 7/16 2 1/8 1 1,200 210 1 9/16 2 3/8 1 1/4 1,200 210 1 5/8 2 5/8 1 1/2 1,200 210 1 1/2 2 5/8 2 1,200 234 1 9/16 2 15/16 2 1/2 1,200 276 1 7/8 3 7/16 3 1,200 276 1 9/16 3 7/16 3 1/2 1,200 321 1 13/16 3 15/16 4 1,200 321 1 9/16 3 15/16 5 1,200 321 1 1/2 4 7/16 6 1,800 442 1 1/2 5 8 5,000 581 1 1/2 6 1/8 10 5,000 581 1 9/16 7 1/4 12 5,000 781 1 9/16 8 1/4 14 5,000 781 1 1/2 8 3/4 16 5,000 844 1 1/2 9 3/4 18 5,000 912 1 1/2 10 3/4 20 7,200 1,044 1 1/2 11 7/8 24 7,200 1,231 1 1/2 13 7/8 30 7,200 1,333 1 1/2 16 7/8 36 7,200 1,803 1 1/2 19 7/8 SCOMPONENTS05.XLS-10/27/11 C PIPE Fig. 186-2 insulation MAX. RECOM. LOAD APPROX. WEIGHT (lb. per 100) COVERING THK. 3/4 1,200 276 1 7/8 2 5/8 1 1,200 276 2 1/8 2 15/16 1 1/4 1,200 276 1 15/16 2 15/16 1 1/2 1,800 318 2 5/16 3 1/2 2 1,800 319 2 1/8 3 1/2 2 1/2 1,800 319 2 5/16 4 3 1,800 358 2 1/16 4 3 1/2 1,800 358 2 1/4 4 1/2 4 1,800 358 2 1/16 4 1/2 5 1,800 358 2 5 6 1,800 573 2 5 9/16 8 1,800 634 2 6 9/16 10 5,000 765 2 1/16 7 3/4 12 5,000 988 2 1/16 8 3/4 14 5,000 988 2 9 1/4 16 5,000 1,040 2 10 1/4 18 7,200 1,040 2 11 3/8 20 7,200 1,161 2 12 3/8 24 7,200 1,335 2 14 3/8 30 7,200 1,408 2 17 3/8 36 7,200 1,893 2 20 3/8 SCOMPONENTS05.XLS-10/27/11 C 136
Fig. 187, 188 & 189 www.pipingtech.com/fig187-189 Pipe Covering Saddle finish: service: note: PIPE MAX. RECOM. LOAD Black, galvanized or painted. Designed to keep insulation from crushing and to reduce heat losses. Specify pipe size, figure number, description, insulation thickness and finish. All saddles are 12 long with the side edges turned up. Fig. 188-3 insulation APPROX. WEIGHT (lb. per 100) COVERING THK. 2 1,800 449 3 1/8 4 1/2 2 1/2 1,800 449 3 3/8 5 3 1,800 491 3 1/16 5 3 1/2 1,800 491 3 5/16 5 9/16 4 1,800 491 3 1/16 5 9/16 5 1,800 491 3 1/16 6 1/16 6 1,800 773 3 6 9/16 8 1,800 773 3 1/8 7 11/16 10 5,000 884 3 1/16 8 3/4 12 5,000 1,135 3 1/16 9 3/4 14 5,000 1,135 3 10 1/4 16 7,200 1,330 3 11 3/8 18 7,200 1,330 3 12 3/8 20 7,200 1,342 3 13 3/8 24 7,200 2,034 3 15 3/8 30 7,200 2,137 3 18 3/8 36 7,200 2,158 3 21 3/8 SCOMPONENTS05.XLS-10/27/11 C PIPE MAX. RECOM. LOAD APPROX. WEIGHT (lb. per 100) COVERING THK. 1 1/4 1,200 361 2 7/16 3 7/16 1 1/2 1,800 361 2 13/16 4 2 1,800 361 2 5/8 4 2 1/2 1,800 406 2 7/8 4 1/2 3 1,800 406 2 9/16 4 1/2 3 1/2 1,800 446 2 3/4 5 4 1,800 446 2 9/16 5 5 1,800 446 2 9/16 5 9/16 6 1,800 651 2 1/2 6 1/16 8 1,800 721 2 11/16 7 3/16 10 5,000 820 2 9/16 8 1/4 12 5,000 1,045 2 5/8 9 1/4 14 5,000 1,045 2 1/2 9 3/4 16 7,200 1,107 2 1/2 10 7/8 18 7,200 1,239 2 1/2 11 7/8 20 7,200 1,239 2 1/2 12 7/8 24 7,200 1,434 2 1/2 14 7/8 30 7,200 1,999 2 1/2 17 7/8 36 7,200 2,020 2 1/2 20 7/8 SCOMPONENTS05.XLS-10/27/11 PIPE Fig. 187-2 1/2 insulation Fig. 189-4 insulation MAX. RECOM. LOAD APPROX. WEIGHT (lb. per 100) COVERING THK. 4 1,800 611 4 1/16 6 9/16 5 1,800 611 4 3/16 7 3/16 6 1,800 1,020 4 1/8 7 11/16 8 1,800 1,020 4 3/16 8 11/16 10 5,000 1,083 4 1/16 9 3/4 12 5,000 1,398 4 1/8 10 3/4 14 5,000 1,398 4 11 1/4 16 7,200 1,530 4 12 3/8 18 7,200 1,530 4 13 3/8 20 7,200 2,279 4 14 3/8 24 7,200 2,305 4 16 3/8 30 7,200 2,396 4 19 3/8 36 7,200 2,413 4 22 3/8 SCOMPONENTS05.XLS-10/27/11 C C 137