JBE LED2000 INDUSTRIAL SOLUTIONS FOR LED & INCANDESCENT MAINS LIGHTING FLICKER FREE TRAILING EDGE DIMMER JBE LED Dimming Controller for 110V* & 220V/ 240V AC LED Systems Thank you for purchasing high quality JBE product. To ensure correct function and safety, please read and follow all instructions carefully before using the product. Please keep instructions for future reference. This DIMMER controller provides the required dim level for 110V, 220V & 240V AC lighting systems. Designed for ultimate flexibility, they allow users to easily add their own personal touch to illumination settings. Its control mode is via a 0-10V/10-0V or 1-10V so you can adjust light to the exact level of brightness you need. The product uses advanced trailing edge dimming technology to provide full control of dimmable LEDs, incandescent lighting, electronic transformer based low voltage lighting, halogen lights & heating elements as well. Temp. front label printing:
WIRING DIAGRANMS: LED DIMMER CONTROLLER SPECIFICATIONS: Output: 1 channels Dimming Technique: Trailing and leading edge Connection mode: Common Neutral Static power consumption: <0.05W Output for Leds 2-2.5KW, incandescent ~2KW Minimum output Load is 10W* Operating voltage: 190V - 260V AC (50Hz). Operating voltage US: 100V - 160V AC (60Hz). Impulse length: Default values is ~100 for 50Hz Power Factor: 96% Adjustable Dimming Range ~0/20-98%* 10V out (manual dimming) jumper s A & B mast ON Over temperature protection Flicker and noise free. Resistant to Off-Peak Ripple Control Signal* Efficiency: > 98% typical EMI: FCC Class A Safety Compliance EMC Emission Compliance
Humidity: Max output current for 220-240VAC: 5A for 1200W, 8A for 2000W & 10A for 2.2KW Max output current for 100-160VAC 500W 5A, 1000W 8A & 10A for custom Working temperature: -40 - +40 C Material: Polycarbonate ABS Enclosures Temp range -40 to 120 C Controller size: L115 x W90 x H60 Item weight: ~0.4Kg* LED CONTROLLER FEATURES: Professional design for home & commercial use eg. theatres & chicken farm Simple brightness adjustment by means of a DC voltage. 0-10V input will accept PWM voltage from wireless dimmer. V DC (0V=min. & 10V=max brightness Soft Start operation. Optically isolated adjust input (0-10V) input only. Overloaded & short circuit (short circuit operate from 500W only) Pre-set adjustment for Low & full brightness. LEDs status indication. Long lasting durability. Fitted with suppressors to minimise radio frequency interference. Military components up 150/175 C. Power conditioning to protect lamps. Increase lamp life, reducing running costs. Complies with Australian and International EMC Standards. Made in Australia. Easy to install
Only graph of heater and incandescent light 0V to 10V Input INSTALATION AMBIENT AIR TEMPERATURE FOR LED2000
Technical Requirements for Control Equipment 1. The light output of the LEDs operated by the dimmable driver is controlled via DC voltage or current applied to the control input terminal (0-10V). For external input (1-10V) mean 10V Dc (jumpers A & B On) is activated for external manual dimming 1-10 Dimmer Potentiometer. 2. The driver is intended for use with control voltages between 0 (zero) and 10 (ten) VDC or custom settings (0-5V) for BUS system. The control equipment must not impose a voltage greater than 25 volt peak maximum on the driver control terminals. 3. The two control types are current source (a theatrical dimming standard) and current sink (a dimming ballast standard). 4. There is an IEC standard for current sink controls - Standard 60929 Annex E. The standard requires that the ballast (or driver) provides full light output when the control voltage is 10 V- (or above). As the control voltage is reduced by the control, the light level is reduced. At a control voltage of 1 V-, the ballast (driver) provides its minimum light level. 5. Annex E requires the ballast (driver) to limit the current draw to 20.0 ma maximum. 6. Current sourcing controls for 0-10 V- are supported by the standard ESTA E1.3, Entertainment Technology Lighting 7. Control System 0-10 V- Analog Control Protocol. It defines 10 V- as 100% light level and 0 V- as off first option & second 10V- as 0% light & 0V- as 100%. Drivers using this protocol require the control to provide (source) the voltage 8. Minimum & maximum brightness settings. The minimum & maximum brightness level has been factory preset to suit most applications. * If you need change this please contact JBE for information. Flicker-free design: Immune to flickering due to Ripple Signal injection on mains supply (as used for off-peak hot water switching) Common Information: Delay + Soft Start: Dimmer incorporates a delay + soft start feature providing a noticeably smooth lamp illumination at turn on. This feature also minimises lamp filament start up stress, which may increase lamp life. Thermal Overload Compensation: Automatically reduces lamp brightness should the dimmer be inadvertently overloaded of overheated Resets automatically once overload conditions are corrected or dimmer cools down. Fuse Cut-Out: The unit contains fast two type fuses designed to blow or open in case of catastrophic circuit failure. This is a secondary protection measure intended to operate as a backup in case of persistent or prolonged overload conditions. If the fuse cut-out (fuse open), need to be replaced. Any significant overload should be avoided in order to prevent damage to the Dimmer.
IMPORTANT Legal Stuff Ensure all work is undertaken by a Registered Electrical trades person only. This product may not be used in any medical apparatus or other technical products that are critical for the functioning of lifesaving or supporting systems. We define these systems as such that in the case of failure may lead to the death or injury of a person. Incorporation in such a system requires the explicit written permission from JBE. Trademarks used in this document are properties Safety Notice Read and understand all safety information in this instruction. Improper installation of the product can result in electrical shock that can result in death or serious injury. If you are not qualified to install this equipment, use a qualified electrical installer. In this instruction, a WARNING box alerts you to a hazard that, if ignored, could result in death or serious personal injury. A Caution box describes a hazard that can cause minor personal injury. The attention triangle tells you about actions that can cause damage to the product or property. Improper installation of this product, or use for any purpose other than described in this instruction, can result in product failure or damage to attached equipment. Pay attention to the specifications and wiring diagrams in this document