Parts Manual Products LT Series Lawn Tractors & Mower Decks Mfg. No. Description 2690917, 23 Gross HP and 42" Mower Deck - After S/N 2014915223 2690917, 23 Gross HP and 42" Mower Deck - Before S/N 2014915223 2690917-01, 23 Gross HP and 42" Mower Deck 2690918, 24 Gross HP and 46" Mower Deck 2690918-01, 24 Gross HP and 46" Mower Deck 2691005, 19.5 Gross HP and 42" Mower Deck Mower Decks Mfg. No. Description 1695925 42" Mower Deck (2011) 1696085 42" Mower Deck (2012) 1695926 46" Mower Deck Manual Part No. Revision H Rev. Date: 3/3/2015
Table Of Contents PRODUCT COMPONENTS Frame & Front Axle Group... 4 Steering Group... 8 Engine Group - 19.5, 23 & 24 Gross HP Briggs & Stratton... 10 Transmission Group... 12 Transmission SERVICE PARTS - Hydro-Gear T2-CCHE-4X3B-1LX1... 14 Controls Group... 20 Electrical Group... 22 Hood, Grille & Dash Group... 24 Seat Deck & Fuel Tank Group... 26 Lift Group - Frame Hung... 28 Wheel & Tire Group... 30 Decals Group... 32 42" Mower Deck - Housing, Arbors & Blades Group... 34 42" Mower Deck - Clutch Group... 36 42" Mower Deck - Height Adjust & Roller Group... 38 46" Mower Deck - Housing, Arbors & Blades Group... 40 46" Mower Deck - Clutch Group... 42 46" Mower Deck - Mower Support Group... 44 42" Mower Deck - Clutch Group... 46 42" Mower Deck - Housing, Arbors & Blades Group... 48 Torque Specification Chart... Inside Back Cover PAGES
Frame & Front Axle Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 4
Frame & Front Axle Group REF NO PART NO. QTY. DESCRIPTION 0010 1734135SM 2 HUB CAP 0020 1611710SM 2 RING, Klipring 0030 2860183SM 4 WASHER, 3/4 0040 1728018SM 1 AXLE, Front 0040-10 1704314SM 1 FITTING, Zerk 0050 1730186SM 2 BUSHING, Axle Pivot 0060 1721918ASM 1 HOOK, Mower, Hitch 0070 1960652SM 2 SCREW, Hex Flange, Whiz Lock, 7/16-14 x 1-1/2 0080 1727902SM 1 PLATE, Axle Support 0090 2860646SM 1 NUT, Hex Flange, Two Way Lock, 5/8-11 0100 1931277SM 24 NUT, Hex Flange, Whiz Lock, 5/16-18 0110 1960032SM 2 SCREW, Hex Head, 3/8-16 x 1-1/4 G5 0120 1731912SM 2 BUSHING 0130 1728080SM 1 TIE ROD (Used on models before Serial No. 2014705554) 0130 1751964YP 1 TIE ROD (Used on models Serial No. 2014705554 and after) 0135 1960703SM 2 WASHER, 5/8 (Used on models Serial No. 2014705554 and after) 0140 1727872ASM 1 WHEEL SPINDLE ASSEMBLY, RH 0150 1930645SM 2 NUT, Hex Flange, Two Way Lock, 3/8-16 0160 1727873ASM 1 WHEEL SPINDLE ASSEMBLY, LH (Used on models before Serial No. 2014705554) 0160 1751922YP 1 WHEEL SPINDLE ASSEMBLY, LH (Used on models Serial No. 2014705554 and after) 0180 1738937YP 1 FRAME 0190 1727904SM 1 SUPPORT, Front Footrest, RH 0210 1738229YP 1 SUPPORT, Rear Brake 0220 1930601SM 9 SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/8 0230 1930591SM 21 SCREW, Hex Flange, Whiz Lock, 5/16-18 x 3/4 0240 1727905SM 1 SUPPORT, Front Footrest, LH 0280 1960035SM 1 WASHER, 5/8 0290 2860744SM 1 CAPSCREW, Hex Head, 5/8-11 x 3-1/4 G5 0300 1727868SM 1 LINK, Drag (with Ball Joint), 3/8 (Used on models before Serial No. 2014705554) 0300 1738051YP 1 LINK, Drag (with Bearing), 5/16 (Used on models Serial No. 2014705554 and after) 0310 1960747SM 2 NUT, Hex, Nylock, 3/8-24 (Used on models before Serial No. 2014705554) 0320 1736404AYP 1 BRAKE PEDAL ASSEMBLY 0330 1735595YP 1 LATCH, Brake Lock 0340 1729576SM 1 BOLT, Shoulder, 5/16-18 x 1-1/8 G5 0350 1727935SM 1 SPACER, Pivot 0360 1736714AYP 1 FORWARD PEDAL ASSEMBLY 0370 1727246SM 1 PEDAL, Reverse 0380 1960223SM 2 BOLT, Carriage, 5/16-18 x 1-1/4 G5 0390 1728024SM 1 SPACER, Foot Pedal 0400 1728025BMYP 1 ACTUATOR, RMO Switch 0410 1727909SM 1 BRACKET, Pedal Pivot 0420 1727911SM 2 PLATE, Bearing 0430 1727282SM 1 SUPPORT, Battery 0470 1737957YP 1 LIFT SHAFT ASSEMBLY Footnotes 5
Frame & Front Axle Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 6
Frame & Front Axle Group REF NO PART NO. QTY. 0490 1727940SM 1 0500 1728027SM 1 0500 1751110YP 1 0510 1728122SM 2 0520 1934654SM 2 0530 1930645SM 2 0540 1727903SM 2 0710 1921977SM 2 0720 1924874SM 2 0730 1935048SM 2 DESCRIPTION BRACKET, Sector Support GEAR, Steering (Used on models before Serial No. 2014705554) GEAR, Steering (Used on models Serial No. 2014705554 and after) SPACER, Sector Gear SCREW, Hex Flange, Whiz Lock, 3/8-16 x 1 NUT, Hex Flange, Whiz Lock, 3/8-16 SUPPORT, Transmission CAPSCREW, Hex Head, 5/16-18 x 1-1/4, G5 (Used on models Serial No. 2014705554 and after) WASHER, 5/16 (Used on models Serial No. 2014705554 and after) NUT, Hex Flange, Two Way Lock, 5/16-18 (Used on models Serial No. 2014705554 and after) Footnotes 7
Steering Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 8
Steering Group REF NO PART NO. QTY. 0010 1727813SM 1 0020 1960114SM 2 0030 1729665SM 2 0040 7078088YP 1 0050 1960576SM 1 0060 1725024SM 1 0140 1611710SM 1 0150 1930601SM 4 0160 1738935AYP 1 DESCRIPTION SHAFT, Steering Gear & Spline WASHER, 3/4 BUSHING, Steering STEERING WHEEL NUT, Hex Lock, ESNA Light, 5/16-18 CAP, Steering Wheel RING, Klipring SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/8 TOWER Footnotes 9
Engine Group - 19.5, 23 & 24 Gross HP Briggs & Stratton NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 10
Engine Group - 19.5, 23 & 24 Gross HP Briggs & Stratton REF NO PART NO. QTY. DESCRIPTION 0010 31P677-0124-B1 1 * ENGINE, 19.5 Gross HP, Briggs & Stratton, Single (Engine Model: 31P677-0124-B1) 0010 44L777-0110-G5 1 * ENGINE, 23 Gross HP Briggs & Stratton ELS Twin (Engine Model: 44L777-0110-G5) 0010 44L777-0119-B1 1 * ENGINE, 23 Gross HP Briggs & Stratton ELS Twin (Engine Model: 44L777-0119-B1) 0010 44L777-5110-G5 1 * ENGINE, 23 Gross HP Briggs & Stratton ELS Twin (Engine Model: 44L777-5110-G5) 0010 44M777-2166-G5 1 * ENGINE, 24 Gross HP Briggs & Stratton ELS Twin (Engine Model: 44M777-2166-G5) 0010 44M777-0166-B1 1 * ENGINE, 24 Gross HP Briggs & Stratton ELS Twin (Engine Model: 44M777-0166-B1) 0010 44M777-5166-G5 1 * ENGINE, 24 Gross HP Briggs & Stratton ELS Twin (Engine Model: 44M777-5166-G5) 0020 1717473SM 1 VALVE, Shut Off (Use on Twin Exhaust Engines) 0020 1750159YP 1 VALVE, Drain (Used on Single Exhaust Engines) 0030 1728058SM 1 HEAT SHIELD, Engine 0040 1930601SM 8 SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/8 0050 1727997SM 1 HEAT SHIELD, Engine, Twin 0060 1727994SM 1 MUFFLER, Twin 0070 1727976SM 1 SUPPORT, Muffler 0080 1727979SM 1 PIPE, Exhaust, RH (Used on Twin Exhaust Engines) 0090 1727980SM 1 PIPE, Exhaust, LH (Used on Twin Exhaust Engines) 0100 1925003SM 4 SCREW, Hex Washer Head, Taptite, 1/4-20 x 1/2 0110 2834683SM 1 CLIP, Wire 0120 1736868YP 1 CONTROL, Throttle, Choke-A-Matic (Used on Twin Exhaust Engines) 0120 1751734YP 1 CONTROL Throttle, Choke-a-Matic (Used on Single Exhaust Engines) 0130 791850 2 CLAMP, Hose 0140 1734993SM 1 HOSE, Fuel 0150 1730268SM 2 CLIP, Hose 0160 2827187SM 2 SCREW, Hex Washer Head, Taptite 3/8-16 x 1 0170 2820427SM 1 WASHER, Lock, External Tooth, 3/8 0180 1924940SM 1 WASHER, 3/8 0190 1732576SM 1 PULLEY & HUB ASSEMBLY, Engine 0200 1701011SM 2 TIE, Self Locking (Qty 1 used on Single Exhaust Engines) 0210 1737421AYP 1 GUIDE, Belt, Long 0220 1736105SM 1 CLUTCH, Electric MID Ogura 0230 1708264SM 1 WASHER, Hex 0240 7091301YP 1 LOCKWSHER, Spring 0250 1960649SM 1 CAPSCREW, Hex Head, 7/16-20 x 3-1/2 G5 0260 1731214SM 2 GASKET, Exhaust (Qty 1 used on Single Exhaust Engines) 0270 2828635SM 2 SCREW, Hex Washer Head, Taptite 3/8-16 x 1-1/4 0280 690341 4 SCREW, Hex, SEMS Lock Washer, 5/16-18 x 7/8 (Qty 2 used on Single Exhaust Engines) 0290 1931277SM 2 NUT, Hex Flange, Whiz Lock, 5/16-18 0300 1728086SM 2 PIVOT, Hood 0310 1931335SM 2 BOLT, Carriage, 5/16-18X1.000 G5 0320 1727982SM 1 SUPPORT, Muffler & Hood Pivot 0330 1728959SM 1 PIPE, Exhaust (Used on Single Exhaust Engines) 0340 1727996SM 1 HEAT SHIELD, Engine, Single 0350 1727993SM 1 MUFFLER, Single Exhaust Footnotes Note* To verify your specific engine model, please reference the ID Tag located on your engine. See your local Briggs & Stratton distributor for parts and service. 11
Transmission Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 12
Transmission Group REF NO PART NO. QTY. 0010 1736637YP 1 0030 1960586SM 4 0040 1931277SM 4 0050 1736716YP 1 0060 1722460SM 2 0070 1750545YP 1 0080 1921977SM 1 0090 1736409YP 1 0100 1721995SM 1 0110 1736854YP 1 0120 1736410AYP 1 0130 1921978SM 1 0140 1664847SM 1 0160 1737441YP 1 0170 1960686SM 2 0180 1919381SM 1 0190 1960221SM 1 0210 015X88MA 1 DESCRIPTION * TRANSMISSION, Hydro Gear, T2-HP SCREW, Hex Flange, Whiz Lock, 5/16-18 x 2-1/2 NUT, Hex Flange, Whiz Lock, 5/16-18 ROD, Free Wheel PIN, Quick ROD, Speed Control CAPSCREW, Hex Head, 5/16-18 x 1-1/4 GR5 SPRING, Extension SPRING, Extension, 6-5/8" SPACER STRAP, Torque CAPSCREW, Hex Head, 5/16-18 x 2 GR5 SCREW, Hex Washer Head, Taptite, 5/16-18 x 3/4 V-BELT, Drive, HA, 88.46 NUT, Hex Flange, ESNA, 5/16-18 WASHER, 5/16 CLIP, Hair Pin NUT, Hex Flange Lock, 5/16-18 Footnotes * Contact Hydro Gear for parts & service 13
Transmission SERVICE PARTS - Hydro-Gear T2-CCHE-4X3B-1LX1 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 14
Transmission SERVICE PARTS - Hydro-Gear T2-CCHE-4X3B-1LX1 REF NO PART NO. QTY. DESCRIPTION 0010 ----- 1 * MAIN HOUSING 0020 ----- 1 * SIDE HOUSING 0070 ----- 1 ** SEAL, Lip, 1/2 x 1 x 1/4 (Included in Item 2050) 0080 ----- 14 * SCREW, Hex Washer, 1/4-20 x 1-1/8 0130 ----- 1 * PLUG, 9/16-18 0210 ----- 1 * BEARING, Journal 0220 ----- 3 * BOLT, Hex Flange, 3/8-16 0230 ----- 1 * PLATE, Bypass 0240 ----- 1 * CHECK PLUG & WASHER ASSEMBLY,.027 0250 ----- 1 * CHECK PLUG & WASHER ASSEMBLY 0260 ----- 1 * BASE, Filter 0270 ----- 1 * COVER, Filter 0280 ----- 1 * RING, Magnet 0290 ----- 1 * DEFLECTOR 0300 ----- 1 ** SEAL, Lip, 3/8 x 3/4 x 1/4 (Included in Item 2050) 0310 ----- 1 ** RING, Retainer, 3/8 (Included in Item 2050) 0320 ----- 1 * ROD, Actuator Bypass 0330 ----- 1 ** RING, Retainer, 3/4 (Included in Item 2050) 0340 ----- 1 * ARM, Bypass 0350 ----- 1 ** RING, Retainer, 3/8 (Included in Item 2050) 0400 ----- 1 * TRUNNION, Swash Plate 0410 ----- 1 ** SCREW, 5/16-18 x 1 (Included in Item 2050) 0610 1752308YP 1 SHAFT, Input 0620 1715142SM 1 BALL BEARING, 15 x 35 x 11 0630 1715141SM 1 ** RING, Retaining Wire,.512 ID (Included in Item 2050) 0640 1706172SM 1 * WASHER, Spacer, 1-15/64 x 9/16 0650 1706173SM 1 ** SEAL, Lip, 15 x 35 x 7 (Included in Item 2050) 0660 ----- 1 ** RING, Retainer, 1-9/16, INT (Included in Item 2050) 0700 ----- 1 * KIT, Block, 7 Piston, 8cc 0740 ----- 1 * BEARING, Thrust Ball, 27 x 47 x 14 0750 ----- 1 * PISTON BLOCK ASSEMBLY 0790 1715144SM 1 BEARING, Thrust Ball, 30 x 52 x 13 0800 ----- 1 ** RING, Retainer, 1/2, EXT (Included in Item 2050) 0810 ----- 1 * GEAR, 13T Pinion 0820 ----- 1 * SHAFT, Motor 0830 ----- 1 * WASHER,.60 x 1 0900 ----- 1 * GEAR, 10T / 48T 0910 ----- 1 * GEAR, Jackshaft, 10T 0920 ----- 1 * JACKSHAFT, Pin 0930 1715169SM 3 WASHER, 7/16 x 1 x 1/2 1000 ----- 2 ** RING, Retainer, Spiral, 5/8, EXT (Included in Item 2050) 1010 ----- 2 * GEAR, Bevel, 12T, Spline OD 1020 ----- 2 * GEAR, Bevel, 12T, 1/2 OD 1030 ----- 1 * SHAFT, Axle, Keyed, 12-9/64 x 3/4 Footnotes Note* See your local authorized dealership for parts and warranty or contact Hydro Gear at www.hydrogear.com/support/northamerica.aspx (U.S. 1-877-728-7410 Int'l 32 (0) 12 670 631) 15
Transmission SERVICE PARTS - Hydro-Gear T2-CCHE-4X3B-1LX1 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 16
Transmission SERVICE PARTS - Hydro-Gear T2-CCHE-4X3B-1LX1 REF NO PART NO. QTY. DESCRIPTION 1040 ----- 1 * SHAFT, Axle, Keyed, 17-3/4 x 3/4 1050 ----- 2 * BUSHING, Inboard 1060 ----- 2 * BUSHING, Outboard 1070 ----- 1 * GEAR, 54T, Bull 1080 ----- 2 * PIN, Differential 1090 ----- 2 ** RING, Retainer, INT, Axle (Included in Item 2050) 1100 ----- 3 ** SEAL, Lip, 3/4 x 1-1/8 x 1/4 (Included in Item 2050) 1200 1706146SM 2 PUCK, Brake 1210 ----- 1 * ROTOR, Brake 1220 1706145SM 1 PLATE, Brake Puck 1240 ----- 1 * YOKE, Brake 1250 1706141SM 2 PIN, Brake, 5/16 x 3/4 1260 1715199SM 1 SPACER, Brake Torsion Spring, 1/4 x 9/16 1270 ----- 1 * SCREW, Patch, 1/4-20 x 2 1280 1706147SM 1 SCREW, Patch, 1/4-20 x 1 1290 ----- 1 * SPRING, Compression, Brake, Anti-Drag 1300 ----- 1 * ARM, Brake 1310 ----- 1 * WASHER, 11/32 x 7/8 1320 1714431SM 1 NUT, Castle, 5/16-24 1330 ----- 1 ** PIN, Cotter, 3/32 x 3/4 (Included in Item 2050) 1340 ----- 1 * SPRING, Brake Arm 1400 ----- 1 * FITTING, Hydraulic, O-Ring Adapter, 5/16 1410 ----- 1 * HOSE 1420 ----- 1 ** O-Ring,.103 x.299 ID (Included in Item 2050) 1600 ----- 1 * ARM, Control 1620 ----- 1 * BOLT, Hex Flange Head 1630 ----- 1 * WASHER, 11/32 x 7/8 (Duplicate of #131) 1640 ----- 1 * ROTATION ASSEMBLY 1650 ----- 1 * NEUTRAL ARM ASSEMBLY 1660 ----- 1 * BUSHING 1670 ----- 1 * SPRING, Extension 1800 1752309YP 2 CLIP, Spring, Housing Thrust 2030 1752310YP 1 E-TANK KIT (Includes ref # 2030-143, 2030-144, 2030-145 & 2030-146) 2030-143 ----- 1 TANK EXPANSION 2030-144 ----- 1 BOLT, 10-32 x 1/2 2030-145 ----- 1 TUBE 2030-146 ----- 1 CAP, Barbed Vent 2040 1752311YP 1 FAN & PULLEY KIT (Includes ref # 2040-150, 2040-151, 2040-152, 2040-153 & 2040-154) 2040-150 ----- 1 * FAN, 7", 10 Blade Footnotes Note* See your local authorized dealership for parts and warranty or contact Hydro Gear at www.hydrogear.com/support/northamerica.aspx (U.S. 1-877-728-7410 Int'l 32 (0) 12 670 631) 17
Transmission SERVICE PARTS - Hydro-Gear T2-CCHE-4X3B-1LX1 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 18
Transmission SERVICE PARTS - Hydro-Gear T2-CCHE-4X3B-1LX1 REF NO PART NO. QTY. DESCRIPTION 2040-151 ----- 1 * PULLEY, 4.4" 2040-152 ----- 1 * NUT, Nylock, 1/2-20 2040-153 ----- 1 * WASHER, OD Slotted 2040-154 ----- 1 * HUB, Pulley, 1-9/16 2050 1752312YP 1 SEAL KIT (Includes items marked with **) Footnotes Note* See your local authorized dealership for parts and warranty or contact Hydro Gear at www.hydrogear.com/support/northamerica.aspx (U.S. 1-877-728-7410 Int'l 32 (0) 12 670 631) 19
Controls Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 20
Controls Group REF NO PART NO. QTY. 0020 1727899SM 1 0030 1727897SM 1 0040 2159181SM 1 0050 1728976SM 1 0080 1728000SM 1 0090 1931277SM 2 0100 1727254SM 1 0110 1722460SM 1 0120 1727261SM 1 0180 1960687SM 2 0190 1931335SM 1 0200 1727935SM 1 0210 1727894ASM 1 0220 1728001SM 1 0230 1729620SM 1 0240 1931352SM 2 0250 1721675SM 1 0280 1727259SM 1 0310 1727267SM 1 0350 1738760YP 1 0360 1728111SM 2 DESCRIPTION ROD, Cruise Latch, 2-7/8" LATCH, Cruise SPRING, Extension, 7-3/4 BOLT, Shoulder, 5/16-18 x 1-5/8 G5 PULLEY, Idler NUT, Hex Flange, Whiz Lock, 5/16-18 ROD, Brake Return, 12-5/8" PIN, Quick PEDAL, Brake NUT, Hex Flange, ESNA, 3/8-16 BOLT, Carriage, 5/16-18X1.000 G5 SPACER, Pivot BRACKET, Idler PULLEY, 3" SPRING, Extension, 7-1/2 BOLT, Carriage, 3/8-16 x 1-1/2 G5 PAD, Foot Pedal Forward PAD, Foot Pedal Reverse ROD, Parking Brake, 16-3/8" ROD, Cruise, 17" CLIP, Linkage Footnotes 21
Electrical Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 22
Electrical Group REF NO PART NO. QTY. 0010 1739597YP 1 0015 1731951SM 1 0030 1930601SM 4 0040 1685215SM 1 0050 1730007SM 1 0060 1931318SM 1 0070 1960353SM 1 0080 1960518SM 1 0090 1920397SM 1 0100 1728963SM 1 0110 1925003SM 2 0120 1686734SM 1 0125 1717163SM 1 0130 2101025SM 1 0140 1960547SM 1 0150 1717549SM 1 0160 1717550SM 1 0170 1728068SM 1 0180 1722887SM 1 0190 1726556SM 1 0210 1716951SM 1 0220 1722611SM 1 0230 1728026ASM 1 0240 1931333SM 2 0250 1931277SM 2 0260 1732006SM 1 0270 1732005SM 1 0280 1716549SM 1 0290 1721830SM 1 0300 1713163SM 1 0310 2816964SM 2 0320 2860750SM 2 0330 2823341SM 2 0340 2821319SM 2 0350 2816622SM 2 0360 1677296SM 1 0370 1701011SM 2 0400 1732004SM 1 0410 1960294SM 1 0420 1726557SM 2 0430 2172434SM 1 0440 1732007SM 1 DESCRIPTION HARNESS, Wiring FUSE, Wiring Harness SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/8 BATTERY, 12 Volt, 230 CCA HOLD DOWN, Battery BOLT, Carriage, 1/4-20 x 7/8 G5 WASHER, 1/4 PUSHNUT, 1/4 NUT, Hex Lock, ESNA Light, 1/4-20 SOLENOID SCREW, Hex Washer Head, Taptite, 1/4-20 x 1/2 SWITCH ASSEMBLY, Ignition (Includes Ref. Nos. 0006, 0130, 0140, 0150, 0160, 0165 KEYS, Ignition WASHER, 5/8 WASHER, Lock, Internal Tooth, 5/8 NUT, Hex Flange, 5/8-32 IGN SW DIE CAST COVER, Switch METER, Hour, With Bracket SWITCH, PTO Push SWITCH, RMO Module SWITCH, Headlight PLUG, Hole SUPPORT, RMO Switch BOLT, Carriage, 5/16-18 x 3/4 G5 NUT, Hex Flange, Whiz Lock, 5/16-18 SWITCH, Push Button (NO/NC) SWITCH, Push Button (NC) CABLE-# 6 X 10.00LG (2) RING TERMINALS CABLE,#6X25 CABLE-# 6 X 26.0 WASHER, Lock, 1/4 NUT, Hex Lock, KEPS, 5/16-24 CAPSCREW, Hex Head, 1/4-20 x 3/4 G5 WASHER, 1/4 NUT, HEX 1/4-20 NC-2B YELLOW BOOT, Insulator, Battery Terminal TIE, Self Locking SWITCH, Push Button (NO) NUT, Hex Flange, Whiz Lock, 1/4-20 KEY, RMO Module CLIP, Wire PLUG, Hole Footnotes 23
Hood, Grille & Dash Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 24
Hood, Grille & Dash Group REF NO PART NO. QTY. DESCRIPTION 0010 1728031CAYP 1 HOOD, W/ Scoop 0020 7102326YP 1 AIR DUCT, Plenum 0030 1727294CAYP 1 PANEL, Side, RH 0040 1727295CAYP 1 PANEL, Side, LH 0050 1738914CAYP 1 GRILLE 0060 1727279ASM 1 HINGE, Hood, LH 0070 1727280ASM 1 HINGE, Hood, RH 0080 1960295SM 12 SCREW, Hex Flange, Whiz Lock, 1/4-20 x 5/8 0090 1930641SM 12 NUT, Hex Flange, Whiz Lock, 1/4-20 0100 1727293SM 1 DASHBOARD 0110 1728089SM 1 KNOB, Brake 0120 1728090SM 1 KNOB, Cruise 0130 1960518SM 2 PUSHNUT, 1/4 0140 1664847SM 2 SCREW, Hex Washer Head, Taptite, 5/16-18 x 3/4 0150 1919381SM 2 WASHER, 5/16 0160 1727999SM 1 COVER, Steering Shaft 0170 1727296SM 1 HEADLIGHT ASSEMBLY (Includes Ref. Nos. 0170-10, 0170-20, 0170-30 & 0170-40) 0170-10 1728973SM 1 REFLECTOR (Included with Ref. No. 0170) 0170-20 1728974SM 1 LENS (Included with Ref. No. 0170) 0170-30 1677371SM 2 BULB, 1141-12V 21CP (Included with Ref. No. 0170) 0170-40 1723451SM 2 SOCKET ASSEMBLY (Included with Ref. No. 0170) 0180 1728975SM 1 INSERT, Lightbar 0190 1960392SM 3 SCREW, Pan Head Phillips, #10-24 x 1/2 0200 1723123SM 1 ROD, Dash, 10 0210 1933896SM 3 NUT, Hex Lock, Nylon Insert, 10-24 0220 1925003SM 1 SCREW, Hex Washer Head, Taptite, 1/4-20 x 1/2 0230 028X83MA 6 S-CLIP 0240 1732030SM 1 GUIDE, Hood, LH 0250 1732031SM 1 GUIDE, Hood, RH 0270 1001803MA 1 INSERT, Grille, LH 0280 1001804MA 1 INSERT, Grille, RH 0290 1001802MA 1 INSERT, Grille, Center 0300 1754094YP 2 POSITIONER, Hood Footnotes 25
Seat Deck & Fuel Tank Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 26
Seat Deck & Fuel Tank Group REF NO PART NO. QTY. DESCRIPTION 0010 1727264CAYP 1 DECK, Seat 0020 1931333SM 2 BOLT, Carriage, 5/16-18 x 3/4 G5 0030 1931277SM 4 NUT, Hex Flange, Whiz Lock, 5/16-18 0040 1728007SM 1 PAD, Footrest, RH 0050 1728006SM 1 PAD, Footrest, LH 0060 1738932YP 1 TANK, Fuel 0060-10 1736609YP 1 FITTING & HOSE ASSEMBLY, Fuel Tank 0060-20 1654930SM 1 BUSHING, Fuel Tank 0070 5101651SM 1 CAP, Fuel Tank 0080 1739535YP 1 POD, LH 0090 1730159SM 1 SEAT, Hi Back 0100 1731300SM 4 SPACER, 5/16 ID x 1-1/4 OD x 5/16 0110 1727265SM 1 SUPPORT, Seat 0120 1727268SM 1 LATCH, Seat 0130 1960667SM 4 CAPSCREW, Hex Flange, Whiz Lock, 5/16-18 x 1 0140 1919381SM 4 WASHER, 5/16 0150 1704724SM 2 COVER, Spring, 1-1/2" 0160 1960686SM 4 NUT, Hex Flange, 5/16-18 ESNA 0170 1709256SM 4 WASHER, Spring 0180 1704728SM 2 SPRING, Compression, 2" 0190 1960282SM 2 BOLT, Carriage, 5/16-18 x 3/4 G5 0200 1727266SM 1 PIVOT, Seat 0210 1930601SM 6 SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/8 0220 1729576SM 2 BOLT, Shoulder, 5/16-18 x 1-1/8 G5 0230 1739537YP 1 POD, RH 0240 1960536SM 6 SCREW, Hex Washer Head, Plastite, 1/4 x 1/2 0250 1722302SM 1 GRIP 0260 1731310SM 1 SUPPORT, Seat Deck 0300 1931334SM 2 BOLT, Carriage, 5/16-18 x 7/8 G5 Footnotes 27
Lift Group - Frame Hung NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 28
Lift Group - Frame Hung REF NO PART NO. QTY. 0010 1728070SM 1 0040 1729652SM 1 0070 1931277SM 3 0100 1731417ASM 2 0110 1732426SM 2 0120 1727955SM 2 0150 1731894SM 2 0160 1960687SM 2 0170 1931211SM 2 0180 1960074SM 4 0190 1727985ASM 1 0200 1730264SM 1 0210 1960252SM 1 0220 1930641SM 1 0230 1960170SM 2 0240 094067MA 2 0250 1666294SM 2 0260 1921333SM 1 0270 1960044SM 1 0280 1728990ASM 1 0290 1727935SM 1 0300 1727954SM 1 DESCRIPTION ROD, Lift Handle, 18-7/8" SPRING, Torsion NUT, Hex Flange, Whiz Lock, 5/16-18 ARM, Rear Lift BOLT, Shoulder, 5/16-18 x 1/2 ROD, Lower Lift, 10" TRUNNION NUT, Hex Flange, ESNA, 3/8-16 NUT, Hex Flange, Whiz Lock, 3/8-16 CLIP, Hair Pin QUADRANT, Lift Height DECAL, Height Of Cut BOLT, Carriage, 1/4-20 x 5/8 G5 NUT, Hex Flange, Whiz Lock, 1/4-20 WASHER, 1/2 PIN, Threaded Shoulder, 3/8-16 x 1-7/16 SPACER, 3/8 ID x 5/8 OD x 7/16 CAPSCREW, Hex Head, 5/16-18 x 1 G5 WASHER, 5/16 CLEVIS, Lift SPACER, Pivot ROD, Lift, 5-1/2" Footnotes 29
Wheel & Tire Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 30
Wheel & Tire Group REF NO PART NO. QTY. 0010 2860202SM 2 0020 1729708SM 2 0020-10 2812808SM 1 0020-20 1742259YP 2 0020-30 2172353SM 2 0020-40 1726301SM 1 0020-50 1731951SM 1 0020-60 1664090SM 2 0030 7101563YP 2 0030-10 7101562YP 1 0030-40 ----- 1 0030-60 2164247SM 2 0040 094618MA 4 0050 0011X3MA 4 0060 17X195MA 4 0070 17X160MA 4 0080 1730181SM 2 0090 021553MA 2 DESCRIPTION WASHER, 3/4 WHEEL & TIRE ASSEMBLY, Front FITTING, Lube BEARING VALVE STEM & CAP WHEEL & BUSHINGS ASSEMBLY, Front TIRE, Turf Rider, Kenda, 15 x 6-6 TUBE, Tire, Front WHEEL & TIRE ASSEMBLY, 20 x 10-8, Rear TIRE, K358 20X10-8 2PLY * WHEEL, Broached Hub, 8 x 7 TUBE, Tire, Rear HUB CAP E-RING WASHER, Flat WASHER, Flat, 3/4 x 1-1/4 SPACER, 3/4 ID x 1-1/4 OD x 1-5/8 KEY, Square, 3/16 Footnotes * Note: Not a serviceable part, order complete wheel & tire assembly. 31
Decals Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 32
Decals Group REF NO PART NO. QTY. 0010 1750742YP 1 0020 1752639YP 2 0020 1752642YP 2 0030 1750740YP 1 0035 1750741YP 1 0060 1734879SM 1 0080 1730202SM 1 0130 1722806SM 1 0140 7105081YP 1 0140 7102193YP 1 0150 7101665YP 2 DESCRIPTION DECAL, Logo DECAL, LT19542 DECAL, LT2342 DECAL, Hood, LH DECAL, Hood, RH DECAL, Tunnel DECAL, Transmission Tow / Release Lever DECAL, Ignition Switch Symbols DECAL, Mower, 42" DECAL, Mower, 46" DECAL, Danger Footnotes 33
42" Mower Deck - Housing, Arbors & Blades Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1695925-42" Mower 34
42" Mower Deck - Housing, Arbors & Blades Group REF NO PART NO. QTY. DESCRIPTION 0010 1922014SM 2 NUT, Hex Jam, 5/8-18 0020 1732354SM 2 PULLEY, 5-1/2" 0030 7072440SM 2 SPACER, Pulley 0040 7012491SM 4 RETAINING RING, Ext, 1-3/4 0050 2108202SM 4 BEARING, Ball 0060 1731372ASM 2 SPINDLE HOUSING 0070 1704314SM 2 FITTING, Lube 0080 7072537SM 2 SHAFT, Spindle 0090 1730100CAYP 1 HOUSING, 42" 0100 1731917SM 2 WASHER, Spindle Blade 0110 1731898ASM 2 BLADE, 42" 0120 7024467SM 4 WASHER, Belleville 0130 7091633SM 2 NUT, Hex, 9/16F 0140 1731209ASM 1 UPSTOP 0150 092426E701MA 2 PLATE, Rear 0160 1931277SM 6 NUT, Hex Flange, Whiz Lock, 5/16-18 0170 094956E701MA 1 BRACKET, Hinge 0180 1931333SM 6 BOLT, Carriage, 5/16-18 x 3/4 G5 0190 1923683SM 10 SCREW, Hex Washer Head, Taptite, 3/8-16 x 3/4 0200 0166X4MA 1 SPRING, Torsion 0210 094707MA 1 DEFLECTOR & SUPPORT ASSEMBLY 0220 094957ZMA 1 ROD, Deflector 0230 1960093SM 2 NUT, Push Pal, 3/8 0240 7090880YP 2 WASHER, Internal Tooth, 5/8 Footnotes 1695925-42" Mower 35
42" Mower Deck - Clutch Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1695925-42" Mower 36
42" Mower Deck - Clutch Group REF NO PART NO. QTY. DESCRIPTION 0010 1922130SM 1 CAPSCREW, Hex Head, 3/8-16 x 2-1/4 G5 0020 1922755SM 4 WASHER, 3/8 0030 7018574SM 2 PULLEY, Idler 0040 1930645SM 1 NUT, Hex Flange, Two Way Lock, 3/8-16 0050 1924356SM 1 WASHER, 3/8 0060 1731944ASM 1 ARM, Idler 0070 1931211SM 2 NUT, Hex Flange, Whiz Lock, 3/8-16 0080 1731311SM 1 SPRING, Extension, 7-3/4 0090 1933468SM 2 WASHER, 5/16 0100 1729007SM 1 SPACER, 3/8 ID x 1-1/2 OD x 1 0110 1732955SM 1 V-BELT, A-Wedge, HA, 94.45 LG 0120 1731911ASM 1 SUPPORT, Idler 0130 2860361SM 1 SCREW, Hex Washer Head, Taptite 3/8-16 x 2 0140 1921971SM 1 CAPSCREW, Hex Head, 3/8-16 x 1-3/4 G5 0150 1923325SM 2 CAPSCREW, Hex Head, 5/16-18 x 7/8 G5 0160 1931277SM 2 NUT, Hex Flange, Whiz Lock, 5/16-18 0170 1732884ASM 1 GUARD, Spring Footnotes 1695925-42" Mower 37
42" Mower Deck - Height Adjust & Roller Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1695925-42" Mower 1696085-42" Mower 38
42" Mower Deck - Height Adjust & Roller Group REF NO PART NO. QTY. DESCRIPTION 0010 1731966BMYP 1 HITCH, Front, 42" 0020 1730097SM 1 ROD, Bail, 13" 0030 1730221ASM 1 HANGER, Front 0040 1679166SM 2 SPACER, 1/2 ID x 7/8 OD x 1-3/16 0050 1960379SM 2 NUT, Hex Lock, ESNA Light, 1/2-13 0060 2176012SM 1 RETAINER, Pin Spring 0070 1731414SM 1 ROD, Latch, 9" 0080 1960687SM 2 NUT, Hex Flange, ESNA, 3/8-16 0090 1731402ASM 1 SUPPORT, Gauge Wheel, RH 0100 1731403ASM 1 SUPPORT, Gauge Wheel, LH 0110 2108765SM 2 BOLT, Wheel, 3/8-16 x 2-3/4 0120 1960170SM 2 WASHER, 1/2 0130 1714760SM 2 WHEEL 0140 1931277SM 13 NUT, Hex Flange, Whiz Lock, 5/16-18 0150 1931333SM 13 BOLT, Carriage, 5/16-18 x 3/4 G5 0160 1730071BMYP 1 SUPPORT, Mower, LH 0170 1730072BMYP 1 SUPPORT, Mower, RH Footnotes 1695925-42" Mower 1696085-42" Mower 39
46" Mower Deck - Housing, Arbors & Blades Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1695926-46" Mower 40
46" Mower Deck - Housing, Arbors & Blades Group REF NO PART NO. QTY. DESCRIPTION 0080 1735734CAYP 1 HOUSING, 46" 0090 1735573YP 3 HOUSING, Spindle 0090-10 1704314SM 3 FITTING, Grease 0091 1735399YP 6 BEARING, Ball 0092 1735326YP 3 SHAFT, Spindle 0093 1735323YP 6 SHIELD, Arbor 0094 1735328YP 6 SPACER, Bearing 0095 1960766YP 6 RING, Self Locking 0100 1960373SM 10 CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 1 0110 1737228AYP 3 BLADE, Mower 0120 1656916SM 4 WASHER, Spring 0130 1920676SM 5 CAPSCREW, Hex Head, 7/16-14 x 1 G5 0200 1735686YP 3 PULLEY, Split, 4.6 OD 0210 1735579YP 2 SPACER, Lower Drive 0220 1736445YP 1 SPACER, Pulley 0240 1918199SM 2 LOCKWSHER, Spring, 7/16 0320 1735447YP 1 DEFLECTOR 0330 1736365AYP 1 PIVOT, Hinge 0340 1931333SM 2 BOLT, Carriage, 5/16-18 x 3/4 G5 0350 1931277SM 4 NUT, Hex Flange, Whiz Lock, 5/16-18 0360 1736364YP 1 SPRING, Torsion, Deflector 0361 1737359AYP 1 PLATE, Deflector Closeoff 0370 1736366YP 1 ROD, Deflector 0380 7012542YP 2 PUSHNUT, 5/16 0390 1923027SM 1 CAPSCREW, Hex Head, 7/16-14 x 1-3/4 G5 0450 1736518AYP 1 BRACKET, Belt Cover, Front 0460 1736519AYP 1 BRACKET, Belt Cover, Rear 0480 1735750YP 1 COVER, Belt, LH 0490 1735752YP 1 COVER, Belt, RH 0500 1664847SM 7 CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/4 0501 1737279AYP 1 BAFFLE, Pinchoff 0510 1930600SM 2 CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 1-1/2 0520 1736898YP 1 CONNECTOR, Washout Port 0530 1735716YP 1 ADAPTER, Washout Port 0580 703302 3 WASHER, Flat, 5/16 Footnotes 1695926-46" Mower 41
46" Mower Deck - Clutch Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1695926-46" Mower 42
46" Mower Deck - Clutch Group REF NO PART NO. QTY. DESCRIPTION 0010 1719911SM 1 V-BELT, 117" 0020 1715772SM 1 SPRING, Extension 5-1/4" 0030 1736540YP 1 PULLEY, Idler 0040 1933685SM 1 CAPSCREW, Hex Head, 3/8-16 x 2-1/2 G5 0050 1922755SM 2 WASHER, 3/8 0060 1931211SM 1 NUT, Hex Flange, Whiz Lock, 3/8-16 0070 1960339SM 1 NUT, Hex Flange, MAC Lock, 3/8-16 0080 1736551AYP 1 ARM, Idler 0090 1729007SM 1 SPACER, 3/8 ID x 1-1/2 OD x 1 0100 1923701SM 1 CAPSCREW, Hex Head, 3/8-16 x 2 G5 0110 1924356SM 2 WASHER, 3/8 0120 7091585SM 1 NUT, Center Lock Hex, 3/8C GR5 0130 1755653BMYP 1 ARM, Idler Footnotes 1695926-46" Mower 43
46" Mower Deck - Mower Support Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1695926-46" Mower 44
46" Mower Deck - Mower Support Group REF NO PART NO. QTY. DESCRIPTION 0010 1736070AYP 1 SUPPORT, Rear Cross 0020 1736072AYP 1 BRACKET, Rear Mower Pickup 0030 1736073AYP 1 BRACKET, Rear Mower Pickup 0040 1664847SM 8 CAPSCREW, Hex Washer Head, Taptite, 5/16-18 x 3/4 0050 1736071AYP 1 HITCH, Front 0080 1736081YP 2 ROD, Front Bail 0090 1737059AYP 1 HANGER, Front Mower 0100 1731414SM 1 ROD, Latch 0110 2176012SM 1 RETAINER, Pin Spring 0120 1679166SM 2 SPACER, 1/2 ID x 7/8 OD x 1-3/16 0130 1960379SM 2 NUT, Hex Lock, ESNA Light, 1/2-13 0140 1736074AYP 2 BRACKET, Gauge Wheel, RH 0150 1736075AYP 2 BRACKET, Gauge Wheel, LH 0160 1931334SM 11 BOLT, Carriage, 5/16-18 x 7/8 G5 0170 1931277SM 13 NUT, Hex Flange, Whiz Lock, 5/16-18 0180 1736896YP 4 WHEEL, Gauge 0190 1736539YP 4 BOLT, Shoulder, 3/8-16 x 3-7/16 0200 1960170SM 6 WASHER, 1/2 0210 1960687SM 4 NUT, Hex Flange, ESNA, 3/8-16 0220 1736991AYP 1 UP STOP 0240 1913744SM 2 NUT, Hex Jam, 1/2 Jam, 1/2-13 0250 1960074SM 2 CLIP, Hair Pin 0260 1931333SM 2 BOLT, Carriage, 5/16-18 x 3/4 G5 Footnotes 1695926-46" Mower 45
42" Mower Deck - Clutch Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1696085-42" Mower 46
42" Mower Deck - Clutch Group REF NO PART NO. QTY. DESCRIPTION 0010 1922130SM 2 CAPSCREW, Hex Head, 3/8-16 x 2-1/4, G5 0020 1922755SM 4 WASHER, 3/8 x 1 OD 0030 7018574SM 2 IDLER, Flat, 4-1/8 0040 1960339SM 2 NUT, Hex Flange, 3/8-16, Locking 0050 1924356SM 2 WASHER, 3/8 x 1-1/2 OD 0060 1731944ASM 1 ARM, Idler 0070 1931211SM 2 NUT, Hex Flange Whiz Lock, 3/8-16 0080 1731311SM 1 SPRING, Extension, 1-1/32 OD x 7-3/4 0090 1933468SM 2 WASHER, 5/16 x 1-1/4 OD 0100 1729007SM 1 SPACER, 3/8 ID X 1-1/2 OD x 1-1/32 0110 1732955SM 1 V-BELT, A-Wedge, HA, 94.45 LG 0120 1731911ASM 1 SUPPORT, Idler 0140 1921971SM 1 CAPSCREW, Hex Head, 3/8-16 x 1-3/4, G5 0150 1923325SM 2 CAPSCREW, Hex Head, 5/16-18 x 7/8, G5 0160 1931277SM 2 NUT, Hex Flange Whiz Lock, 5/16-18 0170 1732884ASM 1 GUARD, Spring Footnotes 1696085-42" Mower 47
42" Mower Deck - Housing, Arbors & Blades Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1696085-42" Mower 48
42" Mower Deck - Housing, Arbors & Blades Group REF NO PART NO. QTY. DESCRIPTION 0010 1735573YP 2 HOUSING, Spindle 0010-10 1704314SM 1 FITTING, Grease (Included in Ref 0010) 0020 1735399YP 4 BEARING, Ball 0030 1735326YP 2 SHAFT, Spindle 0040 1735323YP 4 SHIELD, Arbor 0050 1735328YP 4 SPACER, Bearing 0060 1960766YP 4 RING, Self Lock 0070 1960373SM 12 SCREW, Hex Washer Head, Taptite, 5/16-18 x 1 0080 1737816BMYP 2 BLADE, 42" 0090 1656916SM 4 WASHER, Spring 0100 1920676SM 2 CAPSCREW, Hex Head, 7/16-14 x 1, G5 0110 1737835YP 2 PULLEY, V, Deep Groove 0130 1737457YP 2 SPACER, Pulley 0140 1736504CAYP 1 HOUSING, Mower Deck, 42 0150 1923027SM 2 CAPSCREW, Hex Head, 7/16-14 x 1-3/4, G5 0170 1737845AYP 1 BRACKET, Upstop 0180 092426E701MA 2 PLATE, Rear 0190 1931277SM 7 NUT, Hex Flange, Whiz Lock, 5/16-18 0200 094956E701MA 1 BRACKET, Hinge 0210 1931333SM 7 BOLT, Carriage, Short Neck, 5/16-18 x 3/4 G5 0230 0166X4MA 1 SPRING, Torsion 0240 094707MA 1 DEFLECTOR 0250 094957ZMA 1 ROD, Deflector 0260 1960093SM 2 NUT, Push Pal, 3/8 0270 1750457BMYP 1 PLATE, Spindle, RH 0280 1750458BMYP 1 PLATE, Spindle, LH Footnotes 1696085-42" Mower 49
IT IS THE POLICY OF BRIGGS & STRATTON CORP. TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS. Briggs & Stratton Power Products Group, LLC 3515 N. 124 Street / PO Box 702 Wauwatosa, WI 53222 USA www.briggsandstratton.com www.victa.com.au