Automotive Data Solutions Inc. INSTALL GUIDE ADS-TB--EN AVAILABLE FOR : ADS-TB Rev. Date: May 18, 2017 Doc. No.: ##39487## U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 2017 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
Page 2 of 7 ADS-TB--EN Doc. No.: ##39487## 20170517 INSTALL TYPE SELECTION CHeVroLeT CadILLaC BUICK MaKe ModeL year InsTaLL Type Allure 05-09 1 Century 00-05 1 Lacrosse 05-09 1 LeSabre / Ultra 00-05 1 Park Avenue 98-05 1 Rainier 04-07 1 Regal 00-04 1 Rendez-vous 02-07 1 Terraza 05-07 1 CTS 03-07 1 Deville 01-05 1 Escallade 99-06 1 Escallade EXT 03-06 1 Seville 98-04 1 SLS 98-99 3 SLS 00-04 1 SRX 04-06 1 STS 98-99 3 STS 00-04 1 Astro 98-05 1 Avalanche 03-06 1 Blazer 98-05 1 Cavalier 00-05 1 Express 98-07 1 Impala 00-05 1 Monte Carlo 00-05 1 S10 / S15 98-04 1 Silverado 99-06 1 SSR 04-06 1 Suburban 99-06 1 Tahoe 99-06 1 Trailblazer 02-09 1 Uplander 05-09 1 Venture 99 2 Venture 00-04 1 saturn saab pontiac oldsmobile IsUZU HUMMer C MaKe ModeL year InsTaLL Type Envoy 99-09 1 Jimmy 98-04 1 Safari 98-05 1 Savana 98-07 1 Sierra/ CK 99-06 1 Sonoma 98-04 1 Yukon / Denali 99-06 1 H2 03-07 1 Ascender 03-08 1 Hombre 98-00 1 Alero 99-04 1 Aurora 01-03 1 Bravada 99-04 1 Intrigue 00-02 1 Silhouette 99 2 Silhouette 00-04 1 Aztek 01-05 1 Bonneville 00-05 1 Grand Am 99-05 1 Grand Prix 00-03 2 Grand Prix 04-08 1 Montana 99 2 Montana 00-04 1 Montana SV6 05-09 1 Sunfire 00-05 1 Transport 99 2 97x 06-08 1 Relay 05-07 1 S 00-05 1 NOTE I Please advise that this firmware does not disarm OEM alarm. For OEM alarm arm/disarm application, we recommend using the DL-1, 2, 3 or 4 firmwares (see our website for compatibilty charts).
Page 3 of 7 ADS-TB--EN Doc. No.: ##39487## 20170517 TYPE 1 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. VEHICLE IGNITION REMOTE STARTER IGNITION (+) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) IGNITION (+) INPUT - PINK (NC) PINK/BLACK DATA - ORANGE (NC) GRAY/YELLOW (NC) GRAY/RED (NC) GREEN/YELLOW (NC) GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED DATA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Page 4 of 7 ADS-TB--EN Doc. No.: ##39487## 20170517 TYPE 2 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. REMOTE STARTER PK3 GRAY ORANGE PURPLE BLACK BLUE PINK 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) IGNITION INPUT ECM SIDE - PINK IGNITION OUTPUT IMMOBILIZER SIDE - PINK/BLACK (NC) ORANGE (NC) GRAY/YELLOW DATA OUTPUT - GRAY/RED (NC) GREEN/YELLOW (NC) GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED
Page 5 of 7 ADS-TB--EN Doc. No.: ##39487## 20170517 TYPE 3 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. VEHICLE IGNITION REMOTE STARTER PK3 PASS KEY III THEFT DETERRENT : MODULE, BEHIND DRIVER SIDE DASH, RIGHT OF STEERING COLUMN YELLOW/BLACK IGNITION (+) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED WHITE/BLACK - GROUND WHITE/RED (NC) WHITE - STARTER ENABLE (-) OUTPUT IGNITION (+) INPUT - PINK (NC) PINK/BLACK DATA (J1850) - ORANGE (NC) GRAY/YELLOW (NC) GRAY/RED (NC) GREEN/YELLOW (NC) GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED DATA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH
Page 6 of 7 ADS-TB--EN Doc. No.: ##39487## 20170517 INSTALLATION MODE SELECTION 1 Press and release programming button to select installation mode. LED flashes (1X) once = LED flashes (2X) twice = STANDARD HARDWIRE MODE 2! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE 1 Insert key into ignition. 3 Wait, LED will turn solid GREEN for 2 seconds. 2 START Turn key to START position. (Engine running) 4 OFF Turn key to OFF position. 5 Module Programming Procedure completed.
XX-XX PATENT INSTALL GUIDE PAGE X-X Page 7 of 7 ADS-TB--EN Doc. No.: ##39487## 20170517 IDENTIFY VEHICLE NOTICE YEAR 1 Locate the Vehicle Identification Number (VIN), identify the 10th character then match it to its corresponding year. Æ 4 3 A 5 Y 1 N 5 T A L 8 D 5 R 0 X Æ a 1980 L 1990 y 2000 a 2010 B 1981 M 1991 1 2001 B 2011 C 1982 n 1992 2 2002 C 2012 d 1983 p 1993 3 2003 d 2013 e 1984 r 1994 4 2004 e 2014 F 1985 s 1995 5 2005 F 2015 G 1986 T 1996 6 2006 G 2016 H 1987 V 1997 7 2007 H 2017 J 1988 W 1998 8 2008 J 2018 K 1989 X 1999 9 2009 K 2019 Led status Flashing RED diagnostics during programming during remote start WITH IGnITIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE 1 2 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. This product is protected by one or more of the following patents: U.S. LETTERS PATENT NO. 5,719,551; 6,011,460; 6,243,004; 6,249,216; 6,275,147; 6,297,731; 6,346,876; 6,392,534; 6,529,124; 6,696,927; 6,756,885; 6,756,886; 6,771,167; 6,812,829; 6,924,750; 7,010,402; 7,031,826; 7,046,126; 7,061,137; 7,068,153; 7,015,830; 7,205,679; 7,224,083; 7,369,936; 7,378,945; 7,489,233; 7,501,937; CANADIAN PATENT NO. 2,320,248; 2,415,023; 2,426,670; 2,414,991; 2,415,011; 2,415,027; 2,415,038; 2,415,041; 2,502,893; 2,451,490; 2,452,296; 2,451,487; EUROPEAN PATENT NO. 1,053,128; DE 69807-941T2; U.S. 20020145535; 20060129282; 20060129284; 20040017284; 20080030316; 20090079552; EP1500565; 1538038; 1538037;