CB 23/5 The CB 23/5 is a 5-brush portal with 2 roof dryers, 1 pair of side dryers, and lots of equipment options. The max. washing height is 2.30 m. For locations with 1,200 washes or more per month. 1 Express washing programme High vehicle throughput. Extra revenue for the operator. 2 Compact system An alternative to the short car wash tunnel if space is in short supply. Fits easily into a washing bay with standard dimensions.
TECHNICAL DATA AND EQUIPMENT CB 23/5 Technical data Order no. EAN code 4039784717923 Washing height mm 2300 Plant width with rotating side brushes mm 4035 Plant height without front cover mm 3150 Plant height with front cover mm 3215 Number of wash brushes piece(s) 5 Number of side brushes piece(s) 4 Number of roof brushes piece(s) 1 Number of side dryers pair 1 Number of roof dryers pair 2 Fresh water connection, volume l/min 100 Fresh water connection, pressure bar 4 / 6 Rated input power kw 22 Voltage V 400
Control cable Control cable 3 x 1.5 mm² 1 6.641-059.0 Connecting cable 3 x 1.5 mm². Available by the meter. Available accessories.
2 Water recycling ABS ventilation 1 2.641-510.0 Ventilation pump with air injector. For ventilation of the pump storage basin and avoidance of odour problems. ABS wastewater withdrawal 2 2.641-995.0 Additional swimmer switch including installation material for connection to the WRP control. ABS immersion pump WRP 8000 3 2.642-037.0 Immersion pump with swimmer switch for the WRP 8000 water recycling system. Includes device for attaching to the wall of the pump storage basin. ABS fresh water supply, WRP 8000 4 2.642-113.0 Attachment kit for filling the recycled water tank with fresh water (when there is a water shortage). ABS stand control cabinet 5 2.642-116.0 Base for control cabinet WRP 8000, WRP 16000 or ABS supply pump. Add on additional reclaimed water 6 2.642-117.0 additional reclaimed water tank, 1,000 l tank Add-on kit tank recycling water 7 2.642-720.0 1000 l Add-on kit box add-on 8 2.642-930.0 Assembly kit WRP 8000 9 2.642-933.0 Add-on kit conductivity WRP 8000 10 2.642-935.0 Pipelines kit 2000 l 11 4.640-401.0 Pipelines kit 3000 l 12 4.640-402.0 Control cable pump pit - WRP 13 6.647-276.0 Control cable for connecting the pump storage basin to the WRP system control cabinet. Available by the meter. Available accessories.
9 12 Travel rail extensions 2x 1 m travel rail extension set 1 2.640-460.0 1 m travel way. Hot-galvanised special profile, 40 mm mounting height. The scope of delivery includes mounting and supporting material. The travel rails are directly fixed to the ground. The length of the travel rails depends on the length of the vehicles to be washed. The length is calculated by adding to the length of the longest vehicle to be washed approx. 6 m (for machine movements). The standard length of buses are 12 m and trucks are approximately 18 m long. Frost protection Extension reclaimed water 2 2.642-586.0 Water pressure increase system Supply pump module 3 2.641-991.0 The plant can be equipped with a water pressure increase system if the supply pressure on site is too low. The pump provides the plant with the required flow pressure of 4-6 bar. Water tank 1000 l 4 2.642-501.0 Labels wash height / drive through width Label wash height 2.30 m 5 5.393-102.0 The labels are attached to car portal washing stations with a washing height of 2.30m to indicate the max. washing height. Label: Drive-through width: 2.25 m 6 5.393-106.0 Label for making clear to drivers the maximum drivethrough width of 2.25 m in the gantry car washes from Kärcher. Label: Drive-through width: 2.30 m 7 5.393-980.0 Label for gantry car washes as a warning notice to drivers of the maximum drive-through width of 2.30 m. Brushes Disc brush set Ø 450 mm, standard design Brush Ø450, Radkastenr., RAL 9005 8 2.641-451.0 Brush set consisting of PE brushes in standard Kärcher yellow/black design, required for wheel washing brushes (disc brushes with a diameter of 450 mm) in gantry car washes. 9 2.641-452.0 Brush set consisting of PE brushes in black, required for wheel washing brushes (disc brushes) with a diameter of 450 mm in gantry car washes. PE brushes, CB 23/5 10 2.642-968.0 Washing material in the Kärcher standard design. In the case of this brush facing, the shafts of the roof and side brushes are equipped with PE brush segments. Disc brush set Ø 380 mm, standard design 11 2.643-431.0 The wheel washing brushes (disc brushes with a diameter of 380 mm) in our gantry car washes require these brush sets, which consist of PE brushes in a standard Kärcher yellow and black design. Disc brush set Ø 380 mm, black 12 2.643-600.0 Brush set required for wheel washing brushes (disc brushes) on gantry car washes. The brush sets consist of PE brushes in black and have a diameter of 380 mm. Energy supply Cable transport 12m CB5 13 2.643-093.0 Cable carrier consisting of a roller trolley for the attachment of cables and hoses. The hot-dip galvanised C-profile rail acts as a guide for the trolley. Suitable for max. 12m driverails. Front doors Add-on kit doors complete Ampel links Available accessories. 14 2.643-010.0 The "Deluxe" front doors are made from a high-quality plastic in RAL 7012 and RAL 1018. With 3-field LED positioning lights, to the left in the direction of entry.
19 Add-on kit doors complete Ampel rechts Add-on kit doors complete Ampel rechts u Add-on kit doors complete Ampel - Wasch Reclaimed water Connections for reclaimed water operation Fill level control cleaning agents Low level control of Kärcher 10 l or 25 l detergent drums External dosing station for max. 5 dosing pumps 15 2.643-011.0 The "Deluxe" front doors are made from a high-quality plastic in RAL 7012 and RAL 1018. With 3-field LED positioning lights, to the right in the direction of entry. 16 2.643-012.0 The "Deluxe" front doors are made from a high-quality plastic in RAL 7012 and RAL 1018. With 3-field LED positioning lights on the left and right. 17 2.643-013.0 The "Deluxe" front doors are made from a high-quality plastic in RAL 7012 and RAL 1018. With 3-field LED positioning lights on both sides, incl. wash phase symbol lights. 18 4.025-934.0 Required attachment kit for recycled water operation in car portal washing stations. Required for a water recycling plant already present at the customer's premises or for a delivered water recycling plant system. 19 2.641-221.0 Indicates if the fill size of the on-board canisters is too low. This feature will utilize is full potential with the remote-signaling system (available autumn 2006). 20 2.641-262.0 Opens the possibility of storing detergent offboard (e.g. technical room). The big advantage is, that detergent can be stored in bigger quantities, up to 200l per detergent. If the plant is highly frequented the kit minimises the detergent refilling procedure a lot. It is only available in connection with the supply via energy chain. 10 l chemical storage drum, empty 21 6.393-480.0 Detergents can be stored on the plant. The available space can be used for either 2 x 25 l canisters, or 1 x 25 l and 2 x 10 l canisters or 4 x 10 l canisters. The concept of the plant allows the use of the same detergent (out of the same canister) for the two programs foam and shampoo and for the two programs drying aid and hot wax. Currently the detergents are only available in 25 l canisters. Thus the 10 l canisters are needed in case different detergents are used for each program or when the plant is equipped with the additional washing program intensive pre-wash. Frost protection system Extension 60 bar HP 22 2.641-095.0 Extension manual frost protection pre-spraying rims / intensive pre-wash complete / spot-free rinsing Available accessories. 23 2.641-154.0 Prevents the plant and vehicles from suffering any damage open up after all water has been blown out. Thus possible There are two options regarding the frost protection: With a manual switch the operator gives the signal to blow out the basic machine.
Extension automatic frost protection pre-spraying rims / intensive pre-wash complete / spot-free rinsing 24 2.641-155.0 Prevents the plant and vehicles from suffering any damage open up after all water has been blown out. Thus possible There are two options regarding the frost protection. Assembly plate frost protection 25 2.641-258.0 Expansion: automatic frost protection HP 60 bar 26 2.642-845.0 Winter damage to the system can be reliably prevented with the automatic 60 bar frost protection. This process involves compressed air which effectively dries the water-bearing parts. 27 2.642-854.0 By blowing compressed air through feed pipes, water distributors and spray lances, the automatic 60 bar frost protection prevents damage caused by low temperatures. Automatic frost protection 28 2.850-718.0 Prevents the plant and vehicles from suffering any damage Extension automatic frost protection 29 2.850-719.0 high-pressure side / under chassis wash open up after all water has been blown out. Thus possible There are two options regarding the frost protection: A thermostat monitors the temperature. In case of frost it gives the signal to start the process. Frost protection manual 30 2.850-722.0 Prevents the plant and vehicles from suffering any damage open up after all water has been blown out. Thus possible There are two options regarding the frost protection: With a manual switch the operator gives the signal to blow out the basic machine. Extension of automatic antifreeze, process water mode Available accessories. 31 2.850-726.0 Prevents the plant and vehicles from suffering any damage open up after all water has been blown out. Thus possible There are two options regarding the frost protection: A thermostat monitors the temperature. In case of frost it gives the signal to start the process.
Extension of manual antifreeze, high-pressure, side / underbody wash 32 2.850-727.0 Prevents the plant and vehicles from suffering any damage open up after all water has been blown out. Thus possible There are two options regarding the frost protection: With a manual switch the operator gives the signal to blow out the basic machine. Pumps 60 bar high-pressure pump 33 2.640-973.0 Rugged high-pressure pump module consisting of two crankshaft pumps. Suitable for supply of gantry car washes with 60 bar high pressure and for both fresh and reclaim water. Medium pressure pump 16 bar 34 2.641-061.0 Standing, multi-level medium pressure centrifugal pump including central switch cabinet. The pump must be supplied by a tank in order to ensure safe operation. Voltage: 3~ / 400 V / 50 Hz High-pressure pump HD-E 60/6 K2 li 35 2.641-126.0 Crank shaft high-pressure pump unit mounted on a rack including control cabinet. Power 3~ / 400 V / 50 Hz Medium pressure pump 16 bar 36 2.641-147.0 Vertical, multistage medium-pressure centrifugal pump in inline version including control unit. The pump is prepared to be connected to a buffer tank on site. Power 3~ / 400 V / 50 Hz ABS tank plastics HD Modul CB 37 2.851-053.0 Fresh water tank module with a capacity of 210 litres for supplying water to portal washing stations. It is installed on the pump module. Supply valve included. Guide rails Tyre deflector 38 2.641-027.0 Lateral guides to position the vehicles safely within the wash bay. Made of solid hot galvanised tubes mounted onto the ground. Safety devices Switch narrow wash hall exit/rear 39 2.642-960.0 The "Too narrow bay exit/rear" safety device for car portal washing stations ensures that the required safety distances are observed. Add-on kit safety switch positioning CB5 40 2.642-991.0 The "Too wide vehicle" safety device for car portal washing stations ensures that the required safety distances are observed. Add-on kit switch hall too narrow 41 2.642-992.0 The "Too short bay entrance/front" safety device for car portal washing stations ensures that the required safety distances are observed. Add-on kit safety switch rear CB 5/23 42 2.643-034.0 The "Too short bay exit/rear" safety device for car portal washing stations ensures that the required safety distances are observed. Spray protection Splash guard side brushes CB 5 23 43 2.643-092.0 The "Side splash guard" splash guard device for a washing height of 2.30m protects adjacent areas from spray water and contamination caused by the rotating brushes. Available accessories.
Under chassis wash Under chassis wash with segment control Pump connector kit, underbody wash 44 2.641-087.0 The two high-pressure tubes of the under-chassis wash are divided in three identical segments. Depending on the length of the vehicle segments are switched on, one after another. The under chassis wash unit removes dirt adhering to the under chassis of the vehicle to be washed. Two high-pressure tubes made of stainless steel are integrated within an under chassis wash aggregate. Their swivelling movements enlarge the cleaning surfaces on the under chassis of the vehicle. The swivelling of the tubes is carried out by a maintenance-free pneumatic cylinder. The unit can be installed in or above the floor. The basic frame is hot galvanised. The panelling is corrugated aluminium to prevent slipping. 45 2.641-215.0 If the medium pressure pump is used for the under chassis wash then this kit delivers everything for connecting the two components. The under chassis wash unit removes dirt adhering to the under chassis of the vehicle to be washed. Two high-pressure tubes made of stainless steel are integrated within an under chassis wash aggregate. Their swivelling movements enlarge the cleaning surfaces on the under chassis of the vehicle. The swivelling of the tubes is carried out by a maintenance-free pneumatic cylinder. The unit can be installed in or above the floor. The basic frame is hot galvanised. The panelling is corrugated aluminium to prevent slipping. Under chassis wash fixed 16 bar 46 2.642-399.0 Add-on kit subsoil washing low 47 2.642-400.0 cost 6MPa 48 2.642-855.0 The "High-pressure undercarriage wash (HD/UBW) changeover valve" attachment kit enables the supply of water for undercarriage and high-pressure washing for car portal washing stations via the same pump. Wheel wash RAWA HD inside CB5 49 2.850-004.7 Internally irrigated high-pressure wheel washing unit for car portal washing stations. For effective wheel and sill washing and a completely clean vehicle. RAWA external CB5 50 2.850-005.7 This externally irrigated wheel washing unit for portal washing stations works without high pressure. Wheels and wheel rims are cleaned exclusively by disc brushes. RAWA HD contactless CB5 51 2.850-006.7 High-pressure touchless wheel washing unit for portal washing stations. For effective wheel and sill washing using high pressure only (without disc brushes) for a completely clean vehicle. Covering elements Add-on kit covering front quer 52 2.642-995.0 The front trim is attached in front of the roof brush and completes the look and feel of the car portal washing station. Ideal for washing bays at locations with brisk public traffic. Add-on kit covering rear quer 53 2.642-996.0 The rear trim conceals the side brush girders and is recommended for outside installations and installations in drivethrough bays at locations with brisk public traffic. Add-on kit ticker 54 2.643-179.0 Front trim for car portal washing stations with customisable, easy-to-read moving LED display (ticker). Available accessories.
56 67 68 Solar panel CB5 55 2.643-232.0 The UV protection cover for car portal washing stations protects power lines, water hoses, and components attached to the system from harmful UV radiation in the case of outside installations. Wash card reader / pin coder reader Interface for self serve starting device including key switch Water reclamation systems Changeover osmosis engineering room 56 2.641-014.0 The "interface" is a prerequisite for connecting a wash card reader to the system. The various operating states are selected via the key-operated switch. Position 0: System off (end of operating time) Position 1: no manual programme start possible On the control section only manual interventions and functions are available. The wash programmes can be started only with the wash card reader Position 2: Programme start via control section and card reader possible This position allows programme start via the wash card reader and the control section. In addition all manual functions are available on the control section. 57 2.643-177.0 With the "Osmosis" washing programme option, all mineral deposits are removed by a rinse process using osmosis demineralised water. For a stain-free surface with no grey film. Additional programs Wheel precleaning 58 2.641-792.7 Special wheel cleaner is sprayed on the wheels before they are washed with high pressure and brushes. Pre-cleaner Intensive Dirt Remover CB5 59 2.642-976.7 Effective and intensive cleaning before the high-pressure and brush cleaning at the front. Loosens insect residue and other types of stubborn dirt effectively. Foam polishing dosing pump 60 2.643-178.7 The "Kärcher foam polish" care programme enables paintwork preservation without intermediate drying. For a longer vehicle paintwork life and an enduring, visible shine. High-pressure Manifold side/roof for CB Flex/23 61 2.850-971.7 Manifold side/wheel wash unit for 62 2.850-974.7 CB Flex/23 Manifold side/roof/wheel wash 63 2.850-978.7 unit for CB Flex/23 Manifold high-pressure wheel wash single 64 2.851-007.7 The "High-pressure wheel washing (HD-Rawa) changeover" attachment kit enables the supply of the wheel washing unit by means of the provided high-pressure pump. Additional controls Signal distributor 65 3.812-371.0 Signal distributor for ensuring a functioning connection to existing pump engineering and water reclamation systems. UBW external attachment kit 66 4.812-056.0 Attachment kit for gantry car washes for the control of an undercarriage washing station with a sheathed cable, already present at the customer's premises. Can patch cable 20 m 67 6.649-618.0 Communication line between feed distributor which is installed Can patch cable 50 m 68 6.649-619.0 at the energy chain and other components like frost protection and door control that are mounted in the technical room. Roof drier with pivoting vane Baffle-type roof drier 69 2.642-538.7 A baffle diverts the air jet for efficient drying at the rear. Available accessories.
Gate control Basic gate control 70 2.641-776.0 Basic gate control is a basic transducer for gate opening and closing functions and can be adapted to any gate already installed on the premises. Extension gate control basic, gate 71 2.641-777.0 no. 1 Expansion of basic gate control, gate no. 2 72 2.641-778.0 Light barriers for drive-through check: optional expansion of the gate control of the second gate of the gantry car washes. Thermostat 73 2.641-950.0 Thermostat for precise regulation of the ambient temperature. Depending on the values measured, the gate remains open or is closed automatically when temperatures become too low. Cable for thermostat 74 6.641-122.0 Power cable connecting the thermostat for temperature-dependent operating mode switching to the gate control. Available accessories.