General information GENERAL USE : U.G. Closed three-phase asynchronous brake motors, LSMV series with failsafe continuous (dc) brake, according to IEC 3, 72, EN 50281. Single speed : 0.25 to 11, frame size from 71 to 160 mm, 2,, 6 230/00 V, 50 Hz. Presentation of the brake motor IP55 protection providing a good sealing against projected liquid and dust in an industrial environment s for variable speed operation : fitted with thermal probes in winding (obligatory) Options Choice of brake s ; manual brake release Drip cover ; 2nd shaft end Plug in connector Encoders and/or forced ventilation Finish : aluminium housing Routine test, no load test, dielectric test, control of the resistance and direction of rotation. Protection of the flange and shaft end against atmospheric corrosion. Individual anti-shock packaging. motor supplies Standard according to IEC 38 : 230/00 V +10 % 10 % ; suitable for the following supplies: 220/380 V +5 % 5 % and 20/15 V +5 % 5 % 00 V Δ +10 % 10 %. Design suitable for Υ/Δ starting. The brake mains is separate : the alternating (ac) is exterior to the motor Description of the aluminium brake three-phase motors Component Materials Remarks Finned housing Stator Rotor Shaft Auminium alloy Insulated low carbon magnetic steel laminations Electrolytic copper Insulated low carbon magnetic steel laminations Steel - with cast feet, or without feet - pressure die-cast mounting holes for the feet housing lifting rings frame size series 160, option in 132 and 112 - optional earth terminal - the low carbon content guarantees long term stability of the characteristics - welded sheet steel lamination pack - semi-enclosed slots - magnetic circuit based on acquired experience in frequency variation - impregnation resistant to violent voltage variations generated by the high chopping frequency of variable speed drive IGBT transistors. Confor with standard IEC3-17 - insulation system class F - PTC thermal protection (1 by phase) and OTP - inclined slots - squirrel cage pressure die cast in aluminium (or alloy for special applications) - mounted on the shaft by heat shrinking - level B rotor dynamic balancing - for all frame sizes : centre holes fitted with screw and a shaft end washer closed keyway End shields Cast iron - front and rear assembled with tie rods Bearings Lipseals Fan Synthetic rubber Aluminium alloy or cast iron - ball bearings, sealed, lubricated for life, with the following mounting locked rear to provide precise positioning of the load no matter the load direction preloaded front to eliminate axial movement - front and rear joints for IP 55 sealing at the shaft - 2 directions of rotation : straight blades Fan cover Sheet steel - on request, fitted with a drip cover for operation in vertical position, shaft facing down Terminal box Aluminium alloy - IP 55, rotatable in directions for flange version, mounted opposite position to the feet for foot and foot and flange versions - fitted with a 6 steel stud terminal board (brass as an optional extra) with connection by copper straps - delivered with polyamide cable glands - 1 earth terminal in all terminal boxes Painting - system Ia, colour RAL 9005 (black) - resistance to saline mist : 72 h (following NFX 1002) C13.1
Reference position is viewed from side F (drive end shaft) Foot mounted motor Variable speed asynchronous Mounting - Operating positions IM 1051 (IM B6) IM 1061 (IM B7) IM 1071 (IM B8) IM 1011 (IM V5) IM 1031 (IM V6) (FF) plain hole flange mounted motor IM 3011 (IM V1) IM 3031 (IM V3) IM 2001 (IM B35) IM 2011 (IM V15) IM 2031 (IM V36) (FT) tapped hole flange mounted motor (IM B1) IM 3611 (IM V18) IM 3631 (IM V19) IM 2101 IM 2111 (IM V58) IM 2131 (IM V69) A Positions of the terminal box in relation to the motor shaft end A - UP Positions of the cable gland in relation to the motor shaft end 3 - LEFT D - LEFT B - RIGHT C - DOWN 1 - RIGHT Foot mounted motor Flange mounted motor Standard in the terminal box A: only possibility A - UP: standard (1: RIGHT and 3: LEFT possible) C13.2
M Variable speed asynchronous Adaptation possibilities Leroy-Somer offers, for use with their general use brake motors, many options which meet the needs of highly diverse applications. They are described below and included in other chapters of the catalogue relating to gearboxes and variable speed drives. For other variants or any specific adaptation, consult the technical specialists at Leroy-Somer who will be pleased to advise you. brake motors may be integrally mounted (fitted motor), or with universal mounting (IEC standardised motor) with the following gearboxes : Compabloc Orthobloc Manubloc Multibloc brake motors may be controlled by a variable speed drive : Centralised system with separate variable speed drive (open loop vector variable speed drive technology or universal variable speed drive). Decentralised system with variable speed drive close to the motor. GEARBOXES DRIVING SPEED VARIATION Centralised system COMPABLOC ORTHOBLOC Universal mounting MU MI integrated FCR brake motor Standardised B5 (FF) or B1 (FT) FCR brake motor Separate variable speed drive Decentralised system Variable speed drive close to the brake motor MANUBLOC Encoder option MULTIBLOC AP Input shaft Foot mounted FCR brake motor Encoder + forced ventilation Designation / Codification P LS 1500 MV 80 L 0.75 230/00 V 50 Hz U.G. FCR 01 10 A1 Speed polarity series frame size Manuf. index (motor) rated : Mounting position Power frequency and voltage Use Inertia and brake T Box and PE position Codification example LSMV flange motor, 1500, 230/00 V Designation : P LSMV 80 L 0.75 B5 230/00 V 50 Hz U.G. FCR 01 10 All the products in this catalogue have a code. The coding table is incorporated in the price list together with the list of designations. Each brake motor product is classified first in order of and then in order of speed. C13.3
2 3000 LSMV series motor - IP 55-50 Hz - Class F - 230 V Δ / 00 V Υ - IP 55 - Separate mains - set in factory without option I N 00 V A LSMV 160 MP FCR 02 11 2935 20.6 35.8 120 280 550 90 62 110 1. Take into account the maximum mechanical speed : 000. 2. applied, with no applied voltage, when the continuous (dc) circuit is cut. release applied applied LSMV 71 L FCR 01 0.37 2900 1.07 1.22 5 60 90 10 1.075 12 LSMV 71 L FCR 01 0.55 2890 1.2 1.82 5 60 90 10 1.25 13 LSMV 80 L FCR 01 0.75 2865 1.6 2.5 10 80 85 10 1.9 16.8 LSMV 80 L FCR 01 1.1 2880 2.2 3.7 10 80 85 10 2.1 18.8 LSMV 90 L FCR 01 1.5 2885 2.9 5 20 150 10 10 3.5 26 LSMV 90 L FCR 01 2.2 2900.6 7.1 20 150 10 10.1 28. LSMV 100 L FCR 01 3 2875 5.7 9.9 25 150 10 10.7 33. LSMV 112 MG FCR 01 2900 7.5 13.2 3 150 580 0 13.5 52 LSMV 132 SM FCR 02 5.5 2915 10.1 18 80 280 620 90 3 78 LSMV 132 M FCR 02 7.5 2910 13.6 2.5 80 280 620 90 5 87 LSMV 132 M FCR 02 9 290 16.6 29.3 105 280 620 90 5 97 1500 LSMV series motor - IP 55-50 Hz - Class F - 230 V Δ / 00 V Υ - IP 55 - Separate mains - set in factory without option N max 1. Take into account the maximum mechanical speed : 000. 2. applied, with no applied voltage, when the continuous (dc) circuit is cut. release applied applied LSMV 71 L FCR 01 0.25 15 000 1.68 5 60 90 10 1.075 11.5 LSMV 71 L FCR 01 0.37 10 000 2.9 5 60 90 10 1.25 12.5 LSMV 80 L FCR 01 0.55 120 000 3.7 10 80 85 10 2.3 13.8 LSMV 80 L FCR 01 0.75 135 000 5.12 10 80 85 10 3. 16.6 LSMV 90 SL FCR 01 1.1 15 000 7.35 20 150 10 10 5.7 22.7 LSMV 90 L FCR 01 1.5 135 000 10.03 20 150 10 10 6.8 2.7 LSMV 100 L FCR 01 2.2 10 000 1.5 25 150 10 10 7.95 30 LSMV 100 L FCR 01 3 135 000 19.5 25 150 10 10 8.9 33 LSMV 112 MG FCR 01 10 000 26.56 3 150 580 0 19.3 9.3 LSMV 132 SM FCR 02 5.5 160 000 36.3 80 280 620 90 60. 71.3 LSMV 132 M FCR 02 7.5 155 000 9. 80 280 620 90 62 77.3 LSMV 132 M FCR 02 9 160 000 59.3 105 280 620 90 65.5 80 LSMV 160 MR FCR 02 11 160 000 72.2 120 280 550 90 96 102 C13.
2 3000 Variable speed asynchronous U.G. general use IP 55-50 Hz - Class F - 00 V Υ without option (IM B1) Code Qty Code Qty Code Qty LSMV 71 L FCR 01 0.37 5 - - - LSMV 71 L FCR 01 0.55 5 - - - LSMV 80 L FCR 01 0.75 10 - - - LSMV 80 L FCR 01 1.1 10 - - - LSMV 90 L FCR 01 1.5 20 - - - LSMV 90 L FCR 01 2.2 20 - - - LSMV 100 L FCR 01 3 25 - - - LSMV 112 MG FCR 01 3 - - - LSMV 132 SM FCR 02 5.5 80 - - - LSMV 132 M FCR 02 7.5 80 - - - LSMV 132 M FCR 02 9 105 - - - LSMV 160 MP FCR 02 11 120 - - - 1500 U.G. general use IP 55-50 Hz - Class F - 00 V Υ without option (IM B1) Code Qty Code Qty Code Qty LSMV 71 L FCR 01 0.25 5 56070-56071 5 56072 5 LSMV 71 L FCR 01 0.37 5 56075-23596 5 56077 5 LSMV 80 L FCR 01 0.55 10 617313-593872 5 592112 5 LSMV 80 L FCR 01 0.75 10 137092-139936 5 077659 5 LSMV 90 SL FCR 01 1.1 20 560786-560788 5 560789 5 LSMV 90 L FCR 01 1.5 20 252670-16069 5 29709 5 LSMV 100 L FCR 01 2.2 25 560981-2687 5 31676 5 LSMV 100 L FCR 01 3 25 56098-20127 5 560986 5 LSMV 112 MG FCR 01 3 186370-08263 5 560991 5 LSMV 132 SM FCR 02 5.5 80 31385-560992 3 56099 - LSMV 132 M FCR 02 7.5 80 56106-560996 3 56107 - LSMV 132 M FCR 02 9 105 56108-325939 3 561050 - LSMV 160 MR FCR 02 11 120 561053-561051 1 561052 - example : Designation : Required : 1.1 P LSMV 90 SL 1.1 B5 230/00V Required speed : 1500 UG FCR 01 20 Mounting and position : Code : 560788 Mains voltage: 230/00 V C13.5
1500 LSMV series motor - IP 55-50 Hz - Class F - 230 V Δ / 00 V Υ - IP 55 - Separate mains - set in factory + incremental encoder 5V 102 pts N max 1. Take into account the maximum mechanical speed : 000. 2. applied, with no applied voltage, when the continuous (dc) circuit is cut release applied applied LSMV 71 L FCR 01 0.25 15 000 1.68 5 60 90 10 1.075 11.5 LSMV 71 L FCR 01 0.37 10 000 2.9 5 60 90 10 1.25 12.5 LSMV 80 L FCR 01 0.75 135 000 5.12 10 80 85 10 3. 16.6 LSMV 90 SL FCR 01 1.1 15 000 7.35 20 150 10 10 5.7 22.7 LSMV 90 L FCR 01 1.5 135 000 10.03 20 150 10 10 6.7 2.7 LSMV 100 L FCR 01 2.2 10 000 1.5 25 150 10 10 8.9 30 LSMV 100 L FCR 01 3 135 000 19.5 25 150 10 10 8.9 33 LSMV 112 MG FCR 01 10 000 26.56 3 150 580 0 19.3 9.3 LSMV 132 SM FCR 02 5.5 160 000 36.3 80 280 620 90 60. 71.3 LSMV 132 M FCR 02 7.5 155 000 9. 80 280 620 90 62 77.3 LSMV 132 M FCR 02 9 160 000 59.3 105 280 620 90 65.5 80 LSMV 160 MR FCR 02 11 160 000 72.2 120 280 550 90 96 102 + V.F. + incremental 1500 LSMV series motor - IP 55-50 Hz - Class F - 230 V Δ / 00 V Υ - IP 55 - Separate mains - set in factory encoder 5V 102 pts N max LSMV 160 MR FCR 02 11 160 000 72.2 120 280 550 90 96 102 1. Take into account the maximum mechanical speed : 000. 2. applied, with no applied voltage, when the continuous (dc) circuit is cut release applied applied LSMV 71 L FCR 01 0.25 15 000 1.68 5 60 90 10 1.075 11.5 LSMV 71 L FCR 01 0.37 10 000 2.9 5 60 90 10 1.25 12.5 LSMV 80 L FCR 01 0.75 135 000 5.12 10 80 85 10 3. 16.6 LSMV 90 SL FCR 01 1.1 15 000 7.35 20 150 10 10 5.7 22.7 LSMV 90 L FCR 01 1.5 135 000 10.03 20 150 10 10 6.7 2.7 LSMV 100 L FCR 01 2.2 10 000 1.5 25 150 10 10 8.9 30 LSMV 100 L FCR 01 3 135 000 19.5 25 150 10 10 8.9 33 LSMV 112 MG FCR 01 10 000 26.56 3 150 580 0 19.3 9.3 LSMV 132 SM FCR 02 5.5 160 000 36.3 80 280 620 90 60. 71.3 LSMV 132 M FCR 02 7.5 155 000 9. 80 280 620 90 62 77.3 LSMV 132 M FCR 02 9 160 000 59.3 105 280 620 90 65.5 80 C13.6
1500 General use IP 55-50 Hz - Class F - 00 V Υ + INCREMENTAL ENCODER 5V, 102 points + incremental encoder 5V 102 pts (IM B1) Code Qty Code Qty Code Qty LSMV 71 L FCR 01 0.25 5 562030-563155 5 563156 5 LSMV 71 L FCR 01 0.37 5 562031-563160 5 563161 5 LSMV 80 L FCR 01 0.75 10 31097-218701 5 563162 5 LSMV 90 SL FCR 01 1.1 20 563130-1016 5 563163 5 LSMV 90 L FCR 01 1.5 20 56317-563297 5 563298 5 LSMV 100 L FCR 01 2.2 25 56319-38969 5 563301 5 LSMV 100 L FCR 01 3 25 563151-530581 5 56330 5 LSMV 112 MG FCR 01 3 563152-226900 5 563313 5 LSMV 132 SM FCR 02 5.5 80-563315 3 - LSMV 132 M FCR 02 7.5 80-563319 3 - LSMV 132 M FCR 02 9 105-563320 1 - LSMV 160 MR FCR 02 11 120-7221 1-1500 General use IP 55-50 Hz - Class F - 00 V Υ + INCREMENTAL ENCODER 5V, 102 points + FORCED VENTILATION + V.F. + incremental encoder 5V 102 pts (IM B1) Code Qty Code Qy Code Qty LSMV 71 L FCR 01 0.25 5 563519-563522 5 563527 5 LSMV 71 L FCR 01 0.37 5 563528-563529 5 563532 5 LSMV 80 L FCR 01 0.75 10 563537-563539 5 16196 5 LSMV 90 SL FCR 01 1.1 20 563583-563585 5 563586 5 LSMV 90 L FCR 01 1.5 20 563587-082133 5 563588 5 LSMV 100 L FCR 01 2.2 25 31569-563591 5 563592 5 LSMV 100 L FCR 01 3 25 563589-563596 5 563597 5 LSMV 112 MG FCR 01 3 563593-08072 5 18791 5 LSMV 132 SM FCR 02 5.5 105-563599 3 - LSMV 132 M FCR 02 7.5 105-563600 3 - LSMV 132 M FCR 02 9 120-563603 1 - LSMV 160 MR FCR 02 11 160-563607 1 - example : Designation : Required : 1.5 P LSMV 90 L 1.5 B3 230/00V Required speed : 1500 UG FCR 01 20 Mounting and position : Code : 56317 Mains voltage: 230/00 V Option : Incremental encoder C13.7
+ V.F. + absolute encoder 5V EnDat 8192 pts 096 trs 1500 LSMV series motor - IP 55-50 Hz - Class F - 230 V Δ / 00 V Υ - IP 55 - Separate mains - set in factory N max 1. Take into account the maximum mechanical speed : 000. 2. applied, with no applied voltage, when the continuous (dc) circuit is cut release applied applied LSMV 71 L FCR 01 0.25 15 000 1.68 5 60 90 10 1.075 11.5 LSMV 71 L FCR 01 0.37 10 000 2.9 5 60 90 10 1.25 12.5 LSMV 80 L FCR 01 0.75 135 000 5.12 10 80 85 10 3. 16.6 LSMV 90 SL FCR 01 1.1 15 000 7.35 20 150 10 10 5.7 22.7 LSMV 90 L FCR 01 1.5 135 000 10.03 20 150 10 10 6.7 2.7 LSMV 100 L FCR 01 2.2 10 000 1.5 25 150 10 10 8.9 30 LSMV 100 L FCR 01 3 135 000 19.5 25 150 10 10 8.9 33 LSMV 112 MG FCR 01 10 000 26.56 3 150 580 0 19.3 9.3 LSMV 132 SM FCR 02 5.5 160 000 36.3 80 280 620 90 60. 71.3 LSMV 132 M FCR 02 7.5 155 000 9. 80 280 620 90 62 77.3 LSMV 132 M FCR 02 9 160 000 59.3 105 280 620 90 65.5 80 LSMV 160 MR FCR 02 11 160 000 72.2 120 280 550 90 96 102 without option 6 1000 LSMV series motor - IP 55-50 Hz - Class F - 230 V Δ / 00 V Υ - IP 55 - Separate mains - set in factory I N 00 V A LSMV 132 M FCR 02 5.5 970 12.9 52.5 80 280 620 90 61. 75.5 1. Take into account the maximum mechanical speed : 000. 2. applied, with no applied voltage, when the continuous (dc) circuit is cut release applied applied LSMV 71 L FCR 01 0.18 Consult us 10 LSMV 71 L FCR 01 0.25 Consult us 10. LSMV 80 L FCR 01 0.37 Consult us 16 LSMV 80 L FCR 01 0.55 Consult us 18 LSMV 90 L FCR 01 0.75 930 2.1 7.2 20 150 10 10 5.7 21 LSMV 90 L FCR 01 1.1 915 3 10.5 20 150 10 10 6.6 2 LSMV 100 L FCR 01 1.5 905.2 1.3 25 150 10 10 7.6 28 LSMV 112 MG FCR 01 2.2 905 5.8 21 3 150 580 0 13 1 LSMV 132 M FCR 02 965 9. 38.2 80 280 620 90 5.5 68.5 C13.8
1500 General use IP 55-50 Hz - Class F - 00 V Υ + ABSOLUTE ENCODER 5V, ENDat, 8192 points, 096 turns + FORCED VENTILATION + V.F. + absolute encoder 5V EnDat 8192 pts 096 trs (IM B1) Code Qty Code Qty Code Qty LSMV 71 L FCR 01 0.25 5 56533-56660 - 56700 - LSMV 71 L FCR 01 0.37 5 5652-56693 - 56701 - LSMV 80 L FCR 01 0.75 10 56583-365798 - 56713 - LSMV 90 SL FCR 01 1.1 20 56652-5669 - 5671 - LSMV 90 L FCR 01 1.5 20 56653-56695 - 56715 - LSMV 100 L FCR 01 2.2 25 5665-56696 - 56716 - LSMV 100 L FCR 01 3 25 56655-56697 - 56717 - LSMV 112 MG FCR 01 3 56656-56698 - 56719 - LSMV 132 SM FCR 02 5.5 80 - - - LSMV 132 M FCR 02 7.5 80 - - - LSMV 132 M FCR 02 9 105 - - - LSMV 160 MR FCR 02 11 120 - - - without option 6 General use IP 55-50 Hz - Class F - 00 V Υ 1000 (IM B1) Code Qty Code Qty Code Qty LSMV 71 L FCR 01 0.18 5 - - - LSMV 71 L FCR 01 0.25 5 - - - LSMV 80 L FCR 01 0.37 10 - - - LSMV 80 L FCR 01 0.55 10 - - - LSMV 90 L FCR 01 0.75 20 - - - LSMV 90 L FCR 01 1.1 20 - - - LSMV 100 L FCR 01 1.5 25 - - - LSMV 112 MG FCR 01 2.2 3 - - - LSMV 132 M FCR 02 80 - - - LSMV 132 M FCR 02 5.5 80 - - - example : Designation : Required : 1.1 P LSMV 90 SL 1.1 B5 230/00V Required speed : UG FCR 01 20 A1 Absolute encoder 1500 Code : 5669 Mounting and position : Mains voltage: 230/00V Option : Absolute encoder C13.9
Dimensions Dimensions of the LS FCR asynchronous brake motors According to the operating position and mechanical for of the brake motor Foot mounted motor S Page C2.12 IM 1051 (IM B6) IM 1061 (IM B7) IM 1071 (IM B8) IM 1011 (IM V5) IM 1031 (IM V6) (FF) plain hole flange mounted motor BS Page C2.13 IM 3011 (IM V1) IM 3031 (IM V3) (FT) tapped hole flange mounted motor BT Page C2.1 IM 3061 (IM B1) IM 3611 (IM V18) IM 3631 (IM V19) Options Pages C2.10 and C2.11 Options Dimensions of the FCR asynchronous brake motors, (FF) flange mounted with encoder Encoder Type H LB (volant 01) L LS ou LSMV 71* 130 197 33 38 LS ou LSMV 80* 16 197 38 0.5 LS ou LSMV 90* 156 197 39 33 LS ou LSMV 100* 161 197 58 50 LS ou LSMV 112* 169 197 99 9 LS 132 S* 169 197 511 1 LS or LSMV 132 SM, M* 192 197 603 65 LSMV 160 MR* 192 197 638 55 L LB Dimensions in millimetres H * For the other dimensions, see the dimensions pages above. Dimensions of the FCR asynchronous brake motors, (FF) flange mounted with encoder + forced ventilation * For the other dimensions, see the dimensions pages above. Encoder + Forced ventilation Type H C D LB L LS or LSMV 71* 135 197 68 75 0 38 LS or LSMV 80* 16 197 99 98 7 0.5 LS or LSMV 90* 156 197 131 98 86 33 LS or LSMV 100* 161 197 178 98 550 50 LS or LSMV 112* 169 197 182 110 581 9 LS 132 S* 169 197 19 110 593 9 LS or LSMV 132 SM, M* 192 197 299 110 712 65 LSMV 160 MR* 192 197 3 110 77 55 LB L C D H C13.10