Please Note: Other part numbers not included in this brochure are available. s are valid to 31st Dec 2012. Bulldozer air pre-cleaner filter diesel motor compartment cab silencer stack blade lift cylinder ripper cylinder blade cutting edge push frame track idler track tooth final drive ripper tip tooth track roller frame shank protector ripper shank Hydraulic Shovel/Excavator arm cylinder boom cylinder hinge pin cab arm boom counterweight bucket cylinder diesel engine compartment frame jack pivot cab turntable backward bucket tooth 1 Please contact IBS to order any of these products
s are valid to 31st Dec 2012. Backhoe Loader dipper arm dipper arm cylinder boom backward bucket cab bucket cylinder backhoe controls bucket lever bucket bucket cylinder boom cylinder bucket hinge pin diesel engine compartment lift-arm cylinder lift arm cutting edge Grader blade lift cylinder cab blade shifting mechanism exhaust stack overhead frame counterweight engine compartment front axle blade driving wheels front wheel turntable blade shift cylinder Print Version: LUDOEC0512 Please contact IBS to order any of these products 2
Please Note: Other part numbers not included in this brochure are available. s are valid to 31st Dec 2012. Komatsu Bulldozer Seal Kits Application Serial No. Rod Bore Seal Kit Part No. (Aftermarket kit with Genuine NOK rod seals) (Genuine OEM spec seal kit NOK) DU BUSHING (SIZE) MODEL D375A-1 (Standard) PIN PULLER 15001-30 60 707-98-11020 $35.00 $84.00 30X25 RIPPER TILT 15001-110 200 707-98-74100 $189.00 $357.00 110X35 BLADE TILT 15417-15422 110 225 707-98-74410 $161.00 $357.00 110X35 BLADE TILT 15001-15413 110 225 707-98-74410 $161.00 $357.00 110X35 BLADE TILT 15423-110 225 707-98-74420 $161.00 $357.00 110X35 BLADE TILT 15414-15416 110 225 707-98-74420 $161.00 $357.00 110X35 MODEL D375A-2 PIN PULLER 16001-30 60 707-98-11020 $35.00 $84.00 30X25 RIPPER TILT 16001-110 200 707-98-74100 $189.00 $357.00 110X35 MODEL D375A-3 PIN PULLER 17001-30 60 707-98-11020 $35.00 $84.00 30X25 RIPPER TILT 17001-110 200 707-98-74100 $189.00 $357.00 110X35 TILT 17001-110 225 707-98-74410 $161.00 $357.00 110X35 TILT (LH Pitch) 17001-110 225 707-98-74410 $161.00 $357.00 110X35 TILT (RH Pitch) 17001-110 250 707-98-81010 $182.00 $448.00 110X35 MODEL D375A-5 BLADE LIFT 17608-90 105 707-99-56510 $105.00 $182.00 90X35 BLADE LIFT 17001-17607 90 105 707-98-56620 $105.00 $182.00 90X35 BLADE TILT (L.H) (PITCH DOZER) 17608-110 225 707-99-74450 $161.00 $357.00 110X35 BLADE TILT (L.H) (PITCH DOZER) 17001-17607 110 225 707-98-74410 $161.00 $357.00 110X35 BLADE TILT (R.H) (PITCH DOZER) 17608-110 250 707-98-81010 $182.00 $448.00 110X35 BLADE TILT (R.H) (PITCH DOZER) 17001-17607 110 250 707-99-81010 $182.00 $448.00 110X35 RIPPER LIFT 17608-110 225 707-99-74440 $210.00 $399.00 110X35 RIPPER LIFT 17001-17607 110 225 707-98-74400 $210.00 $399.00 110X35 RIPPER TILT 17001-17607 110 200 707-98-74100 $189.00 $357.00 110X35 RIPPER TILT 17608-110 200 707-99-74020 $196.00 $366.80 110X35 PIN PULLER 17001-30 60 707-98-11020 $35.00 $84.00 30X25 MODEL D475A-1 TILT (K Link) 10001-140 250 707-98-84011 $252.00 $515.20 140X70 BLADE LIFT 10001-110 180 707-98-67510 $147.00 $287.00 110X35 SERVICE 10001-140 280 707-98-84400 $259.00 $644.00 140X70 RIPPER LIFT 10001-120 250 707-98-82010 $259.00 $525.00 120X60 RIPPER TILT 10001-140 250 707-98-84010 $282.24 $553.00 140X70 PIN PULLER 10001-30 60 707-99-11010 $35.00 $84.00 30X25 3 Please contact IBS to order any of these products
s are valid to 31st Dec 2012. Komatsu Bulldozer Seal Kits (cont.) Application Serial No. Rod Bore Seal Kit Part No. (Aftermarket kit with Genuine NOK rod seals) (Genuine OEM spec seal kit NOK) DU BUSHING (SIZE) MODEL D475A-2 BLADE TILT (L.H) (PITCH DOZER) 10201-10466 140 250 707-98-84011 $252.00 $515.20 140X70 BLADE TILT (L.H) (PITCH DOZER) 10467-140 250 707-99-84040 $252.00 $515.20 140X70 BLADE TILT (R.H) (PITCH DOZER) 10467-140 280 707-99-84460 $259.00 $644.00 140X70 BLADE TILT (R.H) (PITCH DOZER) 10201-10466 140 280 707-98-84400 $259.00 $644.00 140X70 BLADE LIFT 10201-10466 110 180 707-98-67510 $147.00 $287.00 110X35 RIPPER LIFT 10467-120 250 707-99-82010 $259.00 $525.00 120X60 RIPPER LIFT 10201-10466 120 250 707-98-82010 $259.00 $525.00 120X60 RIPPER TILT 10467-140 250 707-99-84030 $282.24 $553.00 140X70 RIPPER TILT 10201-10466 140 250 707-98-84010 $282.24 $553.00 140X70 SERVICE 10201-140 280 707-98-84400 $259.00 $644.00 140X70 MODEL D475A-3 BLADE LIFT 10670-110 180 707-99-67430 $252.00 $392.00 110X35 BLADE LIFT 10601-10669 110 180 707-98-67510 $147.00 $287.00 110X35 BLADE TILT 10670-140 250 707-99-84040 $252.00 $515.20 140X70 BLADE TILT 10601-10669 140 250 707-98-84011 $252.00 $515.20 140X70 RIPPER LIFT 10670-120 250 707-99-82010 $259.00 $525.00 120X60 RIPPER LIFT 10601-10669 120 250 707-98-82010 $259.00 $525.00 120X60 RIPPER TILT 10670-140 250 707-99-84030 $282.24 $553.00 140X70 RIPPER TILT 10601-10669 140 250 707-98-84010 $282.24 $553.00 140X70 PIN PULLER 10601-30 60 707-99-11010 $35.00 $84.00 30X25 MODEL D475A-5 BLADE LIFT (Cold weather) 20001-110 180 707-99-67640 POA POA - RIPPER TILT 20001-140 250 707-99-84200 POA POA 140X70 BLADE TILT (Cold weather) 20001-140 250 707-99-84050 POA POA 140X70 RIPPER LIFT 20001-120 225 707-99-75600 POA POA 120X60 RIPPER TILT 20001-140 225 707-99-77620 POA POA 140X70 PIN PULLER 20001-30 60 707-98-11350 POA POA 30X25 Please contact IBS to order any of these products 4
Please Note: Other part numbers not included in this brochure are available. s are valid to 31st Dec 2012. Komatsu Excavators Seal Kits Application Serial No. Rod Bore Seal Kit Part No. (Aftermarket kit with Genuine NOK rod seals) (Genuine OEM spec seal kit NOK) DU BUSHING (SIZE) MODEL PC300-3, PC300LC-3 ARM 12001-110 160 707-98-67100 $168.00 $294.00 - BOOM 12001-100 140 707-98-58200 $137.20 $357.00 - BUCKET 12001-100 140 707-98-58210 $140.00 $280.00 - CLAMSHELL 12001-90 130 707-98-47680 $84.00 $259.00 - WEIGHT REMOVER 12001-85 130 707-98-46600 $105.00 $203.00 - MODEL PC300-5, PC300LC-5 ARM 20001-110 160 707-99-67110 $203.00 $329.00 - BOOM 20001-100 140 707-99-58210 $161.00 $280.00 - BUCKET 20001-100 140 707-99-58110 $147.00 $266.00 - MODEL PC300-6 ARM 80001-110 160 707-99-67110 $203.00 $329.00 - BOOM 80001-100 140 707-99-58210 $161.00 $280.00 - BOOM 33001-100 140 707-99-58360 $161.00 $280.00 - BUCKET 80001-100 140 707-99-58110 $147.00 $266.00 - MODEL PC300LC-6 BOOM 10001-100 140 707-99-58210 $161.00 $280.00 - BOOM 33001-100 140 707-99-58360 $161.00 $280.00 - ARM 33001-110 160 707-99-67280 $196.00 $322.00 - BUCKET 33001-100 140 707-99-58370 $147.00 $266.00 - MODEL PC300-7-8 ARM - 110 160 707-99-72300 $238.00 $371.00 110X35 ARM - 110 160 707-99-72350 $238.00 $371.00 110X35 ARM - 110 160 707-99-67090 $196.00 $371.00 110X35 BOOM - 100 140 707-99-58080 $161.00 $280.00 100X30 BUCKET - 100 140 707-99-58090 $168.00 $287.00 100X30 MODEL PC350-6 BOOM KIT - 100 140 707-99-58360 $161.00 $287.00 100x30 BUCKET KIT - 100 140 707-99-58370 $147.00 $273.00 100x30 ARM KIT - 110 160 707-99-67280 $196.00 $336.00 110x35 MODEL PC450-7K ARM K40001-120 185 707-99-68780 $245.00 $406.00 120x60 ARM (2.4M ARM) K40001-120 185 707-99-68780 $245.00 $406.00 120x60 BOOM K40001-110 160 707-99-67870 $196.00 $336.00 110x30 BUCKET K40001-100 160 707-99-66240 $168.00 $308.00 100x30 5 Please contact IBS to order any of these products
s are valid to 31st Dec 2012. Komatsu Excavators Seal Kits (cont.) Application Serial No. Rod Bore Seal Kit Part No. (Aftermarket kit with Genuine NOK rod seals) (Genuine OEM spec seal kit NOK) DU BUSHING (SIZE) MODEL PC850-8R BOOM 60001 140 200 707-99-76230 $231.00 $399.00 - ARM (2.4M ARM) 60001 120 185 707-99-76150 $238.00 $385.00 120x60 BUCKET 60001 130 185 707-99-69540 $217.00 $364.00 - MODEL PC1000-1 ARM (B/H) 10001-170 250 707-99-89200 $889.00 $1,148.00 - ARM (L/S) 10001-130 180 707-99-69620 $224.00 $364.00 - BOOM (B/H) 10001-160 225 707-99-78620 $616.00 $812.00 160X80 BOOM (L/S) 10001-160 225 707-99-78620 $616.00 $812.00 160X80 BOTTOM DUMP 10001-90 140 707-99-56310 $133.00 $252.00 - BUCKET (B/H) 10001-160 225 707-99-78630 $616.00 $812.00 160X80 BUCKET (L/S) 10001-140 200 707-99-77250 $301.00 $469.00 - MODEL PC1000SE-1 PC1000SP-1 ARM 10001-170 250 707-99-89200 $1,239.00 $1,610.00 - BOOM 10001-160 225 707-99-78620 $868.00 $1,148.00 160X80 BUCKET 10001-160 225 707-99-78630 $868.00 $1,148.00 160X80 MODEL PC1100SP-6 BOOM KIT - 160 225 707-99-78700 $539.00 $749.00 160x80 ARM KIT - 170 250 707-99-89220 $882.00 $1,169.00 - BUCKET KIT 3.4-4.5M Arm - 110 160 707-99-67290 $203.00 $476.00 110x55 BUCKETKIT 5.7M Arm - 140 200 707-99-77120 $434.00 $616.00 140x70 MODEL PC1250LC-8 ARM (BACKHOE) 30001-170 250 707-99-89250 $882.00 $1,113.00 - BOOM (BACKHOE) 30001-30014 160 225 707-99-78740 $574.00 $735.00 - BOOM (BACKHOE) 30001-30015 160 225 707-99-78740 $574.00 $735.00 - BUCKET (BACKHOE) (FOR 3.4M & 4.5M ARM) BUCKET (BACKHOE) (FOR 3.4M & 4.5M ARM) BUCKET (BACKHOE) (FOR 5.7M ARM) MODEL PC1600-1 30001-30014 110 160 707-99-72390 $259.00 $364.00-30001-30015 110 160 707-99-72390 $259.00 $364.00-30001- 140 200 707-99-77190 $455.00 $595.00 - SERVICE 10001-10049 140 200 707-99-77210 $448.00 $609.00 140X70 BUCKET 10050-140 200 707-99-77330 $504.00 $672.00 140X70 SERVICE 10001-160 225 707-99-78610 $665.00 $861.00 - SERVICE 10001-110 180 707-99-67600 $238.00 $378.00 - ARM 10001-10049 160 250 707-99-85200 $644.00 $903.00 160X80 ARM 10050-160 250 707-99-85280 $644.00 $903.00 160X80 SERVICE 10001-160 225 707-99-78600 $665.00 $861.00 - BOOM 10001-10049 190 280 707-99-87600 $1,022.00 $1,407.00 190X40 BOOM 10050-190 280 707-99-87660 $1,022.00 $1,407.00 190X40 SERVICE 10001-190 280 707-99-87610 POA POA - Please contact IBS to order any of these products 6
Please Note: Other part numbers not included in this brochure are available. s are valid to 31st Dec 2012. Komatsu Wheel Loaders Seal Kits MODEL WA420-1 Application Serial No. Rod Bore Seal Kit Part No. (Aftermarket kit with Genuine NOK rod seals) (Genuine OEM spec seal kit NOK) DU BUSHING (SIZE) DUMP 20001-100 200 707-99-73010 $126.00 $294.00 100X50 DUMP 10001-19999 100 200 707-99-73010 $126.00 $294.00 100X40 LIFT 20001-90 160 707-99-64010 $98.00 $224.00 90X35 LIFT 10001-19999 100 160 707-99-66010 $105.00 $238.00 100X35 STEERING 10001-19999 45 90 707-99-24500 $42.00 $112.00 - MODEL WA420-3 DUMP 30001-100 200 707-99-73020 $119.00 $287.00 100X50 DUMP 53055-100 200 707-99-73140 $119.00 $287.00 100X30 LIFT 30001-90 160 707-99-64030 $98.00 $224.00 90X35 LIFT 53052-90 160 707-99-64130 $98.00 $224.00 90X30 GRAPPLE 54101-70 130 707-99-43530 $105.00 $196.00 70X30 STEERING 53046-45 90 707-99-24610 $42.00 $112.00 45X30 STEERING 53001-53045 45 90 707-99-24510 $42.00 $112.00 45X30 MODEL WA470-1-3 DUMP 20001-100 200 707-99-73020 $119.00 $287.00 100X50 DUMP 10001-19999 100 200 707-99-73010 $126.00 $294.00 100X40 LIFT 20001-95 180 707-99-65400 $109.20 $245.00 - LIFT 53064-95 180 707-99-65410 $119.00 $259.00 95X30 LIFT 10001-19999 100 180 707-99-66400 $119.00 $259.00 100X35 STEERING 20001-50 100 707-99-32110 $63.00 $140.00 50X30 STEERING 10001-19999 50 100 707-99-32100 $56.00 $133.00 50X30 STEERING 53059-50 100 707-99-32140 $81.20 $154.00 - MODEL WA470-5-W LIFT 70001-95 180 707-99-65420 $140.00 $280.00 95X30 DUMP / BUCKET 70001-100 200 707-99-73150 $168.00 $336.00 100X30 DUMP (LARGE BUCKET) 70001-120 225 707-99-75490 $259.00 $455.00 120X60 STEERING 70001-50 100 707-99-32250 $107.80 $189.00 - MODEL WA500-1 DUMP / BUCKET 10001-120 225 707-99-75400 $175.00 $371.00 120X60 DUMP / BUCKET 20001-120 225 707-99-75420 $175.00 $371.00 120X60 DUMP (LARGE BUCKET) 10001-140 250 707-99-84010 $217.00 $483.00 140X40 GRAPPLE 10001-70 140 707-99-52100 $105.00 $224.00 70X30 LIFT 10001-110 200 707-99-74010 $147.00 $315.00 110X35 LIFT 20001-110 200 707-99-74015 $161.00 $329.00 110X55 MODEL WA500-3 DUMP 50001-120 225 707-99-75450 $175.00 $371.00 120X60 DUMP 52001-120 225 707-99-75460 $175.00 $371.00 120X60 LIFT 50001-110 200 707-99-74120 $147.00 $315.00 110X55 LIFT 52001-110 200 707-99-74140 $147.00 $315.00 110X55 GRAPPLE 50001-70 140 707-99-52100 $105.00 $224.00 70X30 STEERING 50001-55 110 707-99-34550 $56.00 $133.00 55X30 7 Please contact IBS to order any of these products
s are valid to 31st Dec 2012. Komatsu Wheel Loaders Seal Kits (cont.) MODEL WA600-1 DUMP 10001-140 280 707-99-84400 $203.00 $421.40 140X70 DUMP (FOR FORK) 10001-180 300 707-99-96100 $686.00 $1,162.00 - GRAPPLE 10001-70 140 707-99-52100 $105.00 $224.00 70X30 LIFT 11464-120 225 707-99-75440 $189.00 $378.00 120X60 STEERING 10001-70 130 707-99-43500 $84.00 $182.00 - STEERING 11464-70 130 707-99-43570 $98.00 $196.00 - MODEL WA600-3 DUMP 50001-140 280 707-99-84450 $259.00 $651.00 140X70 DUMP A52001-140 280 707-99-84450 $259.00 $651.00 140X70 DUMP 50001-140 280 707-99-84470 $259.00 $651.00 140X70 DUMP (LARGE BUCKET) 50001-50325 180 300 707-99-96100 $686.00 $1,162.00 - DUMP (LARGE BUCKET) 50326-180 300 707-99-96120 $847.00 $1,316.00 - LIFT 50001-120 225 707-99-75450 $175.00 $366.80 120X60 LIFT A52001-120 225 707-99-75450 $175.00 $366.80 120X60 LIFT 50301-120 225 707-99-75470 $196.00 $392.00 120X60 STEERING 50001-70 130 707-99-43590 $119.00 $217.00 - STEERING A52001-70 130 707-99-43590 $119.00 $217.00 - MODEL WA800-1 DUMP 10001-180 300 707-99-96200 $504.00 $973.00 180x90 DUMP (HI-LIFT) 10001-180 300 707-99-96200 $504.00 $973.00 180x90 LIFT 10001-160 260 707-99-85900 $567.00 $861.00 160X80 LIFT (HI-LIFT) 10001-160 260 707-99-85900 $567.00 $861.00 160X80 STEERING 10001-100 160 707-99-66210 $123.20 $252.00 100X50 MODEL WA800-2 DUMP 10501-180 300 707-99-96200 $504.00 $973.00 180x90 DUMP (HI-LIFT) 10501-180 300 707-99-96200 $504.00 $973.00 180x90 LIFT 10501-160 260 707-99-85900 $567.00 $861.00 160X80 LIFT (HI-LIFT) 10501-160 260 707-99-85900 $567.00 $861.00 160X80 STEERING 10501-100 160 707-99-66210 $123.20 $252.00 100X50 MODEL WA800-3 DUMP 50001-180 300 707-99-96200 $504.00 $973.00 180x90 LIFT 50001-160 260 707-99-85900 $567.00 $861.00 160X80 STEERING 50001-100 160 707-99-66210 $123.20 $252.00 100X50 MODEL WA900-1 DUMP 10001-180 300 707-99-96200 $504.00 $973.00 180x90 LIFT 10001-160 260 707-99-85900 $567.00 $861.00 160X80 STEERING 10001-100 160 707-99-66210 $123.20 $252.00 100X50 MODEL WA900-3 Application Serial No. Rod Bore Seal Kit Part No. (Aftermarket kit with Genuine NOK rod seals) (Genuine OEM spec seal kit NOK) DU BUSHING (SIZE) DUMP 50001-180 300 707-99-96200 $504.00 $973.00 180x90 LIFT 50001-160 260 707-99-85900 $567.00 $861.00 160X80 STEERING 50001-100 160 707-99-66210 $123.20 $252.00 100X50 Please contact IBS to order any of these products 8
Please Note: Other part numbers not included in this brochure are available. s are valid to 31st Dec 2012. Komatsu Dump Trucks Seal Kits MODEL HM400-1 Application Serial No. Rod Bore Seal Kit Part No. (Aftermarket kit with Genuine NOK rod seals) (Genuine OEM spec seal kit NOK) HOIST CYL 1001-1079 90/140 120/160 707-99-64150 $273.00 $350.00 DU BUSHING (SIZE) 140x35 / 90x40 STEERING CYL 1001-70 120 707-98-43260 $91.00 $175.00 70x30 MODEL HM400-2 STEERING CYL 2001-70 120 707-99-43170 $91.00 $175.00 70x30 MODEL HD465-3 STEERING KIT - 60 90 707-98-27510 $86.80 $161.00 60x30 HOIST CYL - 100/170 150/185 - $343.00 $616.00 100x35/170x35 MODEL HD465-5/H605-5 HOIST CYLINDER - 100/170 150/185 569-63-42100 $343.00 $462.00 - HOIST CYLINDER - 100/170 150/185 569-63-62100 $385.00 $504.00 - STEERING CYL - 55 85 707-98-26900 $53.20 $126.00 55X30 STEERING CYL 7001-55 85 707-98-26901 $53.20 $126.00 55X30 STEERING CYL 7512-55 85 707-98-26980 $70.00 $126.00 55X30 HOIST CYLINDER 7001-100/170 150/185 707-99-73800 $385.00 $504.00 - HOIST CYLINDER 7512-100/170 150/185 707-99-73820 $406.00 $525.00 - MODEL HD785-3 STEERING 2001-UP 70 110 707-98-37570 $63.00 $147.00 70X30 HOIST CYLINDER 2177-130/200 180/215 561-63-62102 $490.00 $630.00 - HOIST STEERING 2001-UP 130/200 180/215 707-99-79400 $490.00 $630.00-9 Please contact IBS to order any of these products
s are valid to 31st Dec 2012. Caterpillar Grader Seal Kits Application Serial No. Prefix Rod Bore Cylinder group No. Engineering Design Change level Cat Seal Kit Part number Seal Kit 140G Articulation cylinder Kit 72V,13W,5MD 1.750 3.000 6E1560 00 - UP 227-5350 $30.79 Side Shift cylinder kit 72V,13W,5MD 1.750 3.000 9T2483 00 - UP 227-5350 $30.79 Articulation cylinder Kit 72V,13W,5MD 1.750 3.000 9T8784 00 - UP 227-5350 $30.79 Blade Lift cylinder kit 72V,81V,13W 2.000 3.250 3G5223 00 - UP 238-6661 $29.67 14G Draw Bar Tip cylinder kit 96U 1.750 3.000 8J6256 00 - UP 240-2016 $26.50 Blade Lift cylinder kit 96U 2.250 3.500 9T2703 00 - UP 235-0355 $38.85 Steering cylinder kit 96U 1.750 2.500 9T1301 07 - UP 240-2484 $29.50 Side Shift cylinder kit 96U 2.500 4.000 9T3206 00-06 242-2548 $32.00 Side Shift cylinder kit 96U 2.500 4.000 9T3206 07 - UP 234-1949 $35.00 Wheel Lean cylinder kit 96U 2.000 3.500 9T3219 00 - UP 246-5917 $30.00 16G Blade Tip cylinder kit 93U 2.000 4.000 9T8944 00 - UP 233-9205 $30.00 Blade Tip cylinder kit 93U 2.000 4.000 9T3198 00 - UP 233-9205 $30.00 Side Shift cylinder kit 93U 2.250 3.750 8J6359 00 - UP 241-0900 $25.00 Steering cylinder kit 93U 1.750 2.750 9T2853 00-08 240-2482 $33.00 Steering cylinder kit 93U 1.750 2.750 9T2853 09 - UP 234-2595 $38.00 Wheel Lean cylinder kit 93U 1.750 4.000 3G4750 00 - UP 240-1905 $30.00 16H Articulation cylinder kit ATS 2.500 4.000 9T3050 00-06 242-2548 $32.00 Articulation cylinder kit ATS 2.500 4.000 9T3050 07 - UP 234-1949 $35.00 Blade Lift cylinder kit ATS 2.500 4.000 9T3106 00-06 242-2548 $32.00 Blade Lift cylinder kit ATS 2.500 4.000 9T3106 07 - UP 234-1949 $35.00 Ripper cylinder kit ATS 2.500 5.000 1135624 0 243-0384 $43.00 Side Shift cylinder kit ATS 2.500 4.000 9T3206 00-06 242-2548 $32.00 Steering cylinder kit ATS 1.750 2.750 9T2853 00-08 240-2482 $33.00 Steering cylinder kit ATS 1.750 2.750 9T2854 00-08 240-2482 $33.00 Wheel Lean cylinder kit ATS 1.750 4.000 9T3492 00 - UP 240-4819 $32.84 24H Steering cylinder kit 7 KK 2.500 3.500 8X9017 0 186-4327 $32.00 Please contact IBS to order any of these products 10
Please Note: Other part numbers not included in this brochure are available. s are valid to 31st Dec 2012. Caterpillar Dozer Seal Kits Application Serial No. Prefix Rod Bore Cylinder group No. Engineering Design Change level Cat Seal Kit Part number Seal Kit D9R Blade Lift Cylinder Kit 7TL, 8BL, ABK, ACL 3.000 4.750 6E4433 00-05 319-3565 $55.00 Blade Lift Cylinder Kit 7TL, 8BL, ABK, ACL 3.000 4.750 6E4433 06-09 319-3559 $61.00 Blade Lift Cylinder Kit 7TL, 8BL, ABK, ACL 3.000 4.750 6E4433 10 - UP 319-3558 $75.00 Blade lift Cylinder Kit 7TL, 8BL, ABK, ACL 3.000 4.750 4Z6172 00 - UP 319-3558 $75.00 Blade Tilt Cylinder Kit 7TL, 8BL, ABK, ACL 3.500 8.250 4Z6170 00 - UP 245-6833 $138.00 Ripper Lift Cylinder Kit 7TL, 8BL, ABK, ACL 3.250 7.250 132-5123 00 - UP 245-0596 $107.55 Ripper Lift Cylinder Kit 7TL, 8BL, ABK, ACL 3.250 7.250 123-8098 00 - UP 245-0596 $107.55 Ripper Tilt Cylinder Kit 7TL, 8BL, ABK, ACL 3.000 6.000 9T5807 00 - UP 244-2055 $84.58 D10 Blade Lift Cylinder Kit R/H 76X, 84W 4.000 7.000 9J2958 00-08 246-0653 $84.00 Blade Lift Cylinder Kit R/H 76X, 84W 4.000 7.000 9J2958 9 246-0655 $105.00 Blade Lift Cylinder Kit R/H 76X, 84W 4.000 7.000 9J2958 10 - UP 246-0657 $120.00 Blade Lift Cylinder Kit R/H 76X, 84W 4.000 7.000 9J2959 00-08 246-0653 $84.00 Blade Lift Cylinder Kit R/H 76X, 84W 4.000 7.000 9J2959 9 246-0655 $105.00 Blade Lift Cylinder Kit R/H 76X, 84W 4.000 7.000 9J2959 10 - UP 246-0657 $120.00 Blade Tilt Cylinder Kit 76X, 84W 4.000 10.500 4T3210 01 - UP 246-0649 $178.34 Blade Tilt Cylinder Kit 76X, 84W 4.000 10.500 4T3211 01 - UP 246-0649 $178.34 Blade Tilt Cylinder Kit 76X, 84W 4.000 10.500 1U2711 03 - UP 246-0649 $178.34 Blade Tilt Cylinder Kit 76X, 84W 4.000 10.500 3G5761 01 - UP 246-0649 $178.34 Ripper Lift Cylinder Kit 81W, 82W 3.500 10.500 3G2221 00 - UP 246-0637 $148.27 Ripper Lift Cylinder Kit 81W, 82W 3.500 10.500 3G2222 09 - UP 246-0637 $148.27 Ripper Tilt Cylinder kit 81W, 82W 3.250 8.250 3G2220 00-02 245-0599 $110.72 Ripper Tilt Cylinder kit 81W, 82W 3.250 8.250 3G2220 03 - UP 245-0584 $125.00 D10N, D10R Blade Lift Cylinder Kit 3SK, 3KR 3.500 6.250 9T2869 00-08 319-2248 $79.25 Blade Lift Cylinder Kit 3SK, 3KR 3.500 6.250 9T2869 11 - UP 318-9220 $112.00 Blade Tilt Cylinder kit 3KR 4.000 9.250 9T4279 00 - UP 246-0648 $191.30 Blade Tilt Cylinder kit 3KR 4.000 9.250 9T4280 00 - UP 246-0648 $191.30 Blade Tilt Cylinder kit 3KR 4.000 9.250 9T9204 00 - UP 246-0648 $191.30 Blade Tilt Cylinder kit 3KR 4.000 9.250 9T9203 00 - UP 246-0648 $191.30 Blade Tilt Cylinder kit 3KR 4.000 9.250 9T7341 00 - UP 246-0648 $191.30 Ripper Lift Cylinder kit L/H 2YD, 3SK 3.250 9.250 4T5111 0 245-0588 $116.00 Ripper Lift Cylinder kit L/H 2YD, 3SK 3.250 9.250 4T5111 01-03 245-0589 $157.00 Ripper Lift Cylinder kit L/H 2YD, 3SK 3.250 9.250 4T5111 04 - UP 245-0590 $164.00 Ripper Lift Cylinder kit R/H 2YD, 3SK 3.250 9.250 4T5112 0 245-0588 $116.00 Ripper Lift Cylinder kit R/H 2YD, 3SK 3.250 9.250 4T5112 01-04 245-0589 $157.00 Ripper Lift Cylinder kit R/H 2YD, 3SK 3.250 9.250 4T5112 05 - UP 245-0590 $164.00 Ripper Tilt Cylinder kit 2YD, 3SK 3.250 8.250 4T9977 03 - UP 245-0584 $120.00 11 Please contact IBS to order any of these products
s are valid to 31st Dec 2012. Caterpillar Dozer Seal Kits (cont.) Application Serial No. Prefix Rod Bore Cylinder group No. Engineering Design Change level Cat Seal Kit Part number Seal Kit D11N, D11R Blade Lift Cylinder Kit 74Z 4.000 7.000 4T2727 00-03 246-0653 $84.00 Blade Lift Cylinder Kit 74Z 4.000 7.000 4T2727 04-07 246-0655 $105.00 Blade Lift Cylinder Kit 74Z, 4HK, 8ZR 4.000 7.000 4T2727 8 246-0657 $120.00 Blade Lift Cylinder Kit 74Z, 4HK, 8ZR 4.000 7.000 4T2727 09 - UP 318-9225 $126.50 Blade Lift Cylinder Kit 74Z 4.000 7.000 4T2728 00-03 246-0653 $84.00 Blade Lift Cylinder Kit 74Z 4.000 7.000 4T2728 04-07 246-0655 $105.00 Blade Lift Cylinder Kit 74Z, 4HK, 8ZR 4.000 7.000 4T2728 8 246-0657 $120.00 Blade Lift Cylinder Kit 74Z, 4HK, 8ZR 4.000 7.000 4T2728 09 - UP 318-9225 $126.50 Blade Tilt Cylinder Kit 74Z 4.000 10.500 1U2711 03 - UP 246-0649 $178.34 Blade Tilt Cylinder Kit Ripper Lift Cylinder Kit 74Z 3.500 10.000 101-8581 00 - UP 246-0635 $265.00 Ripper Lift Cylinder Kit 74Z 3.500 10.000 101-8614 00 - UP 246-0635 $265.00 Ripper Lift Cylinder Kit 74Z 3.500 10.000 161-6615 00 - UP 246-0635 $265.00 Ripper Lift Cylinder Kit 74Z 3.500 10.000 161-6616 00 - UP 246-0635 $265.00 Ripper Lift Cylinder Kit 74Z 3.500 10.500 3G2221 00 - UP 246-0637 $148.27 Ripper Lift Cylinder Kit 74Z 3.500 10.500 3G2222 00 - UP 246-0637 $148.27 Ripper Tilt Cylinder Kit 4Hk, 8ZR, 9TR 3.750 7.750 101-8579 00 - UP 245-9840 $141.22 Ripper Tilt Cylinder Kit 4Hk, 8ZR, 9TR 3.750 7.750 101-8580 00 - UP 245-9840 $141.22 Ripper Tilt Cylinder Kit 74Z 3.250 7.750 9T5888 00 - UP 245-0594 $135.00 Please contact IBS to order any of these products 12
Please Note: Other part numbers not included in this brochure are available. s are valid to 31st Dec 2012. Caterpillar Wheel Loader Seal Kits Application Serial No. Prefix Rod Bore Cylinder group No. Engineering Design Change level Cat Seal Kit Part number Seal Kit 980C, 980F Lift Cylinder Kit 13B, 63X, 2XD 3.500 7.500 1U3527 01 - UP 245-6831 $147.00 Lift Cylinder Kit 13B, 63X, 2XD 3.500 7.500 9J5559 02 - UP 245-6831 $147.00 Steering Cylinder Kit 13B, 63X, 2XD 2.250 4.500 9J5869 02-03 241-0896 $31.00 Steering Cylinder Kit 13B, 63X, 2XD 2.250 4.500 9J5869 04 - UP 241-8197 $43.00 988B, 988F Steering Cylinder Kit 13B, 63X, 2XD 2.250 4.500 9J8165 00-03 241-0895 $46.00 Steering Cylinder Kit 13B, 63X, 2XD 2.250 4.500 9J8165 04 - UP 241-7578 $48.50 Tilt Cylinder Kit 50W 3.250 7.750 9J3632 04 - UP 245-0594 $135.00 Lift Cylinder Kit 50W, 8YG, 2ZR 4.000 8.500 4T7585 00 - UP 246-0659 $140.00 992C Lift Cylinder Kit 42X, 49Z 7.000 11.500 1U1771 03 - UP 246-5907 $271.00 Tilt Cylinder Kit 42X, 49Z 4.000 10.000 3G4598 00 - UP 246-0644 $221.00 Tilt Cylinder Kit 42X, 49Z 4.000 10.000 3G4599 00 - UP 246-0644 $221.00 Steering Cylinder Kit 42X, 49Z 3.250 7.000 9J5419 00-04 245-0581 $65.12 Steering Cylinder Kit 42X, 49Z 3.250 7.000 9J5419 05-07 245-0582 $99.79 Steering Cylinder Kit 42X, 49Z 3.250 7.000 9J5419 08 - UP 228-1779 $98.05 992D Lift Cylinder Kit 42X, 49Z 7.000 11.500 9J2994 04 - UP 246-5907 $271.00 992G Lift Cylinder Kit 7HR1, ADZ1 7.000 11.000 112-8209 00 - UP 246-3450 on request Lift Cylinder Kit 7HR1, ADZ1 7.000 11.000 136-7879 00 - UP 246-3450 on request Tilt Cylinder Kit 7HR1, ADZ1 5.500 11.000 167-7996 00 - UP 229-7190 on request Tilt Cylinder Kit 7HR1, ADZ1 5.500 11.000 1124282 00 - UP 229-7190 on request Steering Cylinder Kit 7HR1, ADZ1 3.250 5.500 112-8208 00 - UP 229-7191 $95.00 994, 994D Steering Cylinder Kit 9YF 4.250 7.750 9T9019 00 - UP 246-3431 $165.50 Tilt Cylinder Kit 9YF 5.500 10.500 114-2820 00 - UP 246-3437 $285.00 Tilt Cylinder Kit 9YF 5.500 10.500 114-2821 00 - UP 246-3437 $285.00 Lift Cylinder Kit 9YF 7.000 11.500 102-8731 00 - UP 246-5907 $271.00 13 Please contact IBS to order any of these products
s are valid to 31st Dec 2012. Caterpillar Dump Trucks Seal Kits Application Serial No. Prefix Rod Bore Cylinder group No. Engineering Design Change level Cat Seal Kit Part number Seal Kit 769, 769B Hoist Cylinder Kit 99F, 35W 3.500 7.000 00 - UP $386.12 Front Suspension Kit 99F, 35W 7.000 8.000 7J8286 00 - UP 319-5647 $395.00 Rear Suspension Kit 99F, 35W 7.000 8.500 $218.28 Steering Cylinder Kit 99F, 35W 2.375 3.750 9J1287 00 - UP 257-8422 $40.45 769C, 769D, 771C,771D Hoist Cylinder Kit Front Suspension Kit Rear Suspension Kit OX1, 3BJ, 5TR, 6JR, 5SS, 6YS, 9XS, BCA, BBB O1X, 3BJ, 5TR, 6JR, 5SS, 6YS, 9XS, BCA, BBB O1X, 3BJ, 5TR, 6JR, 5SS, 6YS, 9XS, BCA, BBB 4.000 7.000 00 - UP 8T4772 $171.96 7.000 8.000 9J5476 16 - UP 319-5647 $429.45 7.000 8.500 116-2836 00 - UP 297-6848 $194.52 Steering Cylinder Kit 5SS, 6YS, 9XS, BCA, BBB 2.000 3.000 110-0532 03 - UP 293-7596 $27.50 773, 773B, 773D Hoist Cylinder Kit 63G 4.000 8.250 7J3446 02 - Up $390.00 Hoist Cylinder Kit Hoist Cylinder Kit 63W, 5SC, 7XJ, 6KR, 7ER, 7CS, 8AS 63W, 5SC, 7XJ, 6KR, 7ER, 7CS, 8AS 5.000 8.250 9J2017 03 - UP 336-7376 $295.00 5.000 8.250 9T3122 00 - UP 336-7376 $295.00 Front Suspension 63G, 63W 7.000 8.000 7J3480 02-13 $395.00 Front Suspension 63W, 7XJ, 6KR, 7CS, 8AS 7.000 8.000 7J3480 14 - UP 319-5647 $395.00 Rear Suspension Kit 63W, 7XJ, 6KR, 7CS, 8AS 7.000 8.500 9T6082 00 - UP 297-6848 $245.00 Rear Suspension Kit 63W, 7XJ, 6KR, 7CS, 8AS 7.000 8.500 1162837 00 - UP 297-6848 $245.00 Steering Cylinder Kit 63G, 63W, 7XJ, 6KR 2.375 4.000 7J7686 00 - UP 241-8925 $38.00 Steering Cylinder Kit 7CS, 8AS 2.500 3.500 1053357 03 - UP 294-9583 $40.00 775B, 775D Hoist Cylinder Kit Hoist Cylinder Kit 63W, 5SC, 7XJ, 6KR, 7ER, 7CS, 8AS 63W, 5SC, 7XJ, 6KR, 7ER, 7CS, 8AS 5.000 8.250 9J2017 03 - UP 336-7376 $295.00 5.000 8.250 9T3122 00 - UP 336-7376 $295.00 Front Suspension 63G, 63W 7.000 8.000 7J3480 02-13 $395.00 Front Suspension 63W, 7XJ, 6KR, 7CS, 8AS 7.000 8.000 7J3480 14 - UP 319-5647 $395.00 Rear Suspension Kit 63W, 7XJ, 6KR, 7CS, 8AS 7.000 8.500 9T6082 00 - UP 297-6848 $245.00 Rear Suspension Kit 63W, 7XJ, 6KR, 7CS, 8AS 7.000 8.500 1162837 00 - UP 297-6848 $245.00 Steering Cylinder Kit 63G, 63W, 7XJ, 6KR 2.375 4.000 7J7686 00 - UP 241-8925 $38.00 Steering Cylinder Kit 7CS, 8AS 2.500 3.500 1053357 03 - UP 294-9583 $40.00 Please contact IBS to order any of these products 14
Please Note: Other part numbers not included in this brochure are available. s are valid to 31st Dec 2012. Caterpillar Dump Trucks Seal Kits (cont.) Application Serial No. Prefix Rod Bore Cylinder group No. Engineering Design Change level Cat Seal Kit Part number Seal Kit 776, 776B, 776C Hoist Cylinder Kit 84A, 4YC, 3NF, 4XJ 5.500 9.500 8J8924 02 - UP 336-7375 $266.35 Front Suspension 84A1, 4YC, 3NF, 4XJ 9.000 10.750 02 - UP 113-7463 $585.00 Rear Suspension Kit 84A1, 4YC, 3NF, 4XJ 9.000 10.500 8J8865 02 - UP 113-7482 $218.50 Steering Cylinder Kit 84A1, 4YC, 3NF, 4XJ 2.375 4.000 8J9912 01 - UP 241-8925 $30.00 777, 777B, 777C Hoist Cylinder Kit 84A, 4YC, 3NF, 4XJ 5.500 9.500 8J8924 02 - UP 336-7375 $266.35 Front Suspension 4XJ, 2TK 9.000 10.750 02 - UP 113-7463 $585.00 Rear Suspension Kit 84A1, 4YC, 3NF, 4XJ 9.000 10.500 8J8865 02 - UP 113-7482 $218.50 Steering Cylinder Kit 84A1, 4YC, 3NF, 4XJ 2.375 4.000 8J9912 01 - UP 241-8925 $30.00 776D, 777D Hoist Cylinder Kit 3PR, 2YW, AGC, AGY 5.500 9.500 8J8924 02 - UP 336-7375 $266.35 Front Suspension 3PR, 2YW, AGC, AGY 9.000 10.750 02 - UP 113-7463 $585.00 Rear Suspension Kit 3PR, 2YW, AGC, AGY 9.000 10.500 8J8865 02 - UP 113-7482 $218.50 Steering Cylinder Kit 3PR, 2YW, 5ER 2.375 4.000 8J9912 01 - UP 241-8925 $30.00 Steering Cylinder Kit AFS, AGC, AGY 2.500 3.500 1052440 02 - UP 294-9583 $40.00 785, 785B, 785C Hoist Cylinder Kit Front Suspension 8GB, 6HK, 8YM, 1HW, 5AZ, APX 8GB, 6HK, 8YM, 1HW, 5AZ, APX 7.250 11.500 4T5931 00 - UP 8T4939 $489.87 11.000 13.125 04 - UP 336-7368 $1,200.00 Rear Suspension Kit 8GB, 5RK, 6HK 11.000 12.500 6E6073 00-01 336-7369 $328.50 Rear Suspension Kit Steering Cylinder Kit 8GB, 5RK, 6HK, 8YM, 1HW, 2PZ, 5AZ, APX 8GB, 5RK, 6HK, 8YM, 1HW, 2PZ, 5AZ, APX 11.000 12.500 6E6073 02 - UP 340-6080 $335.20 2.500 5.000 1U3182 04 - UP 243-0384 $42.00 789, 789B, 789C Hoist Cylinder Kit 9ZC, 7EK, 2BW 7.250 12.250 9T2807 00 - UP 8C5788 $657.51 Front Suspension 9ZC, 7EK, 2BW 12.500 15.125 04 - UP 336-7341 $850.00 Rear Suspension Kit 9ZC, 7EK, 2BW 12.500 14.250 4T4844 00 - UP 113-7480 $384.40 Steering Cylinder Kit 9ZC, 7EK, 2BW 2.750 6.000 4T6797 01 - UP 224-0953 $51.82 793, 793B, 793C Hoist Cylinder Kit 3SJ, 1HL, 4AR, 4GZ, ATY 8.750 13.750 9T8911 00 - UP 1125343 $556.00 Front Suspension 3SJ, 1HL, 4AR, 4GZ, ATY 13.500 16.125 1137472 $1,354.76 Rear suspension 3SJ 12.500 14.250 6E1101 00 - UP 1137480 $356.94 Steering Cylinder Kit 3SJ, 1HL, 4AR, 4GZ, ATY 2.750 5.500 9T8912 00 - UP 323-4199 $81.00 15 Please contact IBS to order any of these products
s are valid to 31st Dec 2012. O-Ring Kits for Komatsu & Caterpillar Part Number Description net RKOM466-KU-90 RKOM8-KU-90 RKOMQP-1400688H91 RZK 466-KU-90; HIGH PRESSURE MEGA ORING FOR KOMATSU EQUIPMENT INCLUDING ORINGS FOR PARKER HOSE FITTINGS RZK 8-KUFF-90; HIGH PRESSURE ORS (FLAT FACE) ORING SEAL KIT RZK QP-1400688H91 KOMATSU 07000-1 ORING SEAL KIT $515.00 $65.00 $176.00 RKOM25-KU-90 25-KU-90; HIGH PRESSURE KOMATSU HOSE CONNECTION SEAL KIT FOR BOSS FLANGE AND ORS FITTINGS $220.00 RCTZ1A RCTZ1B RCTZ1C RZK 4C4782 CATERPILLAR ORING KIT - NITRILE - 270-1528 RZK 4C4784 CATERPILLAR D RING KIT - 270-1535 RZK 4C8253 CATERPILLAR ORING KIT - SILICONE - 270-1533 $225.00 $105.00 $255.00 Please contact IBS to order any of these products 16