INSTALL GUIDE DOCUMENT NUMBER 53964 REVISION DATE 28098 FIRMWARE OEM-AL(RS)-CH5-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) ADS-HRN-CH5 (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. BEFORE INSTALLATION - Connect module to computer 2- Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)
VEHICLE LIST - OF PAGE 2 OF 8 FEATURES MAKE MODEL I WARNING Install type & 3 require a T-Harness (sold separately). Install type 2 doesn't require a T-Harness. YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS 3X LOCK START/STANDALONE MOD. PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DATA/MUX STARTER CTRL RAP SHUTDOWN CTRL RAM JEEP DODGE CHRYSLER 200-4 2 or 3 300 / 300C 05-07 Aspen 07-0 2 or 3 PT Cruiser 06-0 Sebring 07-0 2 or 3 Avenger 08-4 2 or 3 Caliber (with start wire) 07 Caliber 07-2 2 or 3 Charger 06-07 Durango 07-0 2 or 3 Magnum 05-07 Nitro 07-2 or 3 Ram 500 07-08 2 or 3 Ram 2500 07-09 2 or 3 Ram 3500 07-09 2 or 3 Ram 3500 chassis cab 07-09 2 or 3 Ram 4500 chassis cab 08-0 2 or 3 Ram 5500 chassis cab 08-0 2 or 3 Commander 06-07 Compass 07-7 2 or 3 Grand Cherokee 05-07 Liberty 08-2 2 or 3 Patriot 07-7 2 or 3 Wrangler JK STD Key AT 07-8 2 or 3 4500 chassis cab 0 2 or 3 5500 chassis cab 0 2 or 3
BOX CONTENTS - OF PAGE 3 OF 8 DOC.: #53964 28098 BOX CONTENTS MODULE 6 PIN WHITE CONNECTOR 4 PIN BLACK CONNECTOR WHITE 2 3 4 5 6 PROGRAMMING BUTTON LED 7 PIN WHITE CONNECTOR 0 PIN BLACK CONNECTOR WHITE WHITE 2 3 4 5 6 7 2 3 M M2 M3 M6 0 9 8 7 6 5 4 3 2 BLACK 3 PIN WHITE CONNECTOR DATA CABLE BLUE 2 3 M4 M5 4 3 2 BLACK DATA PORT (WEBLINK, RF, TELEMATIC) 3 PIN BLUE CONNECTOR DATA CABLE 2 WEBLINK CABLE (required accessory sold separately) CH5 T-HARNESS (optional accessory sold separately) WEBLINK CABLE CH5 T-HARNESS MODULE DATA PORT COMPUTER USB PORT 4 PIN BLACK CABLE
TYPE - WIRE CHART - OF PAGE 4 OF 8 MAKE CHRYSLER MODEL YEAR WIRE DESCRIPTION DODGE CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION JEEP COMPONENT LOCATOR 300 05-07 PT Cruiser 06-0 Caliber with start wire 07 Charger 06-07 Magnum 05-07 Commander 06-07 Grand Cherokee 05-07 Mux C Black 5 pin 2 Purple/Brown (MUX) Ignition switch ~ Starter C Black 5 pin 4 Pink/DkGreen (+) Ignition switch ~ Mux C Black 5 pin 2 Purple/Brown (MUX) Ignition switch ~ Starter C Black 5 pin 4 Pink/LtBlue (+) Ignition switch ~ Mux C Black 5 pin 2 Purple/Brown (MUX) Ignition switch ~ Starter C Black 5 pin 4 Pink/DkGreen (+) Ignition switch ~ Mux C Black 5 pin 2 Purple/Brown (MUX) Ignition switch ~ Starter C Black 5 pin 4 Pink/DkGreen (+) Ignition switch ~ Mux C Black 5 pin 2 Purple/Brown (MUX) Ignition switch ~ Starter C Black 5 pin 4 Pink/DkGreen (+) Ignition switch ~ Mux C Black 5 pin 2 Purple/Brown (MUX) Ignition switch ~ Starter C Black 5 pin 4 Pink/Orange (+) Ignition switch ~ Mux C Black 5 pin 2 Purple/Brown (MUX) Ignition switch ~ Starter C Black 5 pin 4 Pink/Orange (+) Ignition switch ~
TYPE - WIRING DIAGRAM - OF PAGE 5 OF 8 IGNITION SWITCH M M2 M3 M4 M6 M5 DATA CUT AND INSULATE THE PURPLE WIRE (NEXT TO WHITE WIRE) : SKIM CONNECTOR M M2 05 06 05 06 07 GREEN/RED - CONTROL (MUX) OUTPUT PURPLE - STARTER (+) OUTPUT CONTROL (MUX) - STARTER (+) - : SKIM HARNESS 2 5 4 3 2 2 M3 M4 M5 COMPATIBLE ACCESSORY IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. HOOD SWITCH M5 GREEN/BLACK- HOOD STATUS (-) INPUT BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
TYPE 2 - WIRE CHART - OF 2 PAGE 6 OF 8 MAKE MODEL CHRYSLER YEAR WIRE DESCRIPTION DODGE CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR 200-4 Aspen 07-0 Sebring 07-0 Avenger 08-4 Caliber 07-2 Durango 07-0 Nitro 07- CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/Gray (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red/LtBlue (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White/LtBlue (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/Gray (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/LtGreen (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~
TYPE 2 - WIRE CHART - 2 OF 2 PAGE 7 OF 8 MAKE MODEL DODGE JEEP YEAR WIRE DESCRIPTION RAM CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR Ram Pickup 07-0 Compass 07-7 Liberty 08-2 Patriot 07-7 Wrangler JK STD Key AT 07-8 Pickup 0 CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Gray/Red (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red/LtGreen (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/Black (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Blue (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red/LtGreen (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/Black (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/LtBlue (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Mux ~ ~ 8 pin Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Gray/Red (+) Ignition switch ~
TYPE 2 - WIRING DIAGRAM - OF PAGE 8 OF 8 IGNITION SWITCH M M2 M3 M4 M6 M5 DATA MUX - IGNITION (+) - 2V (+) - 05 : SKIM CONNECTOR 8 7 6 5 4 3 2 M GRAY/YELLOW (NC) GRAY/RED (NC) GREEN/YELLOW (NC) GREEN/RED (NC) 05 BLUE/YELLOW (NC) 06 BLUE/RED (NC) CANH - 06 CANL - 07 M2 PINK - IGNITION (+) INPUT PINK/BLACK (NC) ORANGE (NC) ORANGE/WHITE (NC) 05 ORANGE/BLACK (NC) 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH M3 YELLOW - MUX YELLOW/RED (NC) YELLOW/BLACK (NC) M4 WHITE - 2V (+) WHITE/RED (NC) WHITE/BLACK - IGNITION (+) OUTPUT M5 BLUE/WHITE (NC) WHITE (NC) BLACK - GROUND RED - 2V (+) WITHOUT A COMPATIBLE ACCESSORY OR M5 DATA CABLE WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. 7.5A 2V (+) M6 GREEN/BLACK- HOOD STATUS (-) INPUT BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
TYPE 3 - WIRING DIAGRAM - OF PAGE 9 OF 8 IGNITION SWITCH M M2 M3 M4 M6 M5 DATA : SKIM CONNECTOR : SKIM HARNESS M 05 06 M2 M3 M4 05 06 07 COMPATIBLE ACCESSORY IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. M5 M5 GREEN/BLACK- HOOD STATUS (-) INPUT BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
MODULE PROGRAMMING PROCEDURE - STD KEY - OF PAGE 0 OF 8 Close driver door. 07 ACC ON START Turn key to position. Re-open driver door to wake up data bus. 08 Remove key. ACC ON START ACC ON START Insert key into ignition. 09 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. ACC ON START Turn key to ON position. 0 Wait, LED will turn solid GREEN for 2 seconds. 05 LED will turn solid RED. Module Programming Procedure completed. 06 Within 5 seconds, LED will flash GREEN rapidly.
VALET MODE PROGRAMMING PROCEDURE - OF PAGE OF 8 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to 5. Time restriction. Complete next step within 7 seconds. ACC ON START Cycle ignition ON five times [5x /ON] rapidly. ENGINE START STOP Wait, LED will turn solid RED for 2 seconds. ACC ON START Set ignition to position. ENGINE START STOP 05 Valet Mode Programming Procedure completed.
PAGE 2 OF 8 MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 3. >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 ACC ON START DOC.: #53964 28098 TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. 2 Configure every other setting and proceed to step 3. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. 3 MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. 4 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP [X]
MODULE NAVIGATION CHART - OF PAGE 3 OF 8 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. DISARM/UNLOCK BEFORE START ON RELOCK AFTER START ON RELOCK AFTER SHUTDOWN ON FORCE UNLOCK ALL ON FIRST PRESS ON 05 TAKEOVER ENABLE DISABLE* 45 SEC 06 SECURE TAKEOVER DELAY 90 SEC MIN MIN DISABLE 07 FACTORY KEYLESS RS SEQUENCE N/A LOCK + UNLOCK + LOCK CONFIGURATION LOCK + LOCK + LOCK MIN 05 MIN 0 MIN 08 MODULE RUN TIME 5 MIN 05 25 MIN 06 30 MIN 07 35 MIN 08 5 MIN SEC 05 SEC 08 SEC 09 WAIT TO START DELAY 0 SEC 05 5 SEC 06 20 SEC 07 25 SEC 08 30 SEC 0-2 N/A N/A -07 Technical Support only N/A N/A
REMOTE STARTER ERROR CODES - OF PAGE 4 OF 8 REMOTE STARTER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. Foot brake is ON. Hood is open. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error.
MODULE DIAGNOSTICS - OF PAGE 5 OF 8 TEST MODULE LED STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.
MODULE RESET PROCEDURE - OF PAGE 6 OF 8 Disconnect all connectors from module except the BLACK 4-PIN connector. 07 Reconnect all connectors. Disconnect the BLACK 4-PIN connector. 08 Repeat programming procedure. PRESS AND HOLD programming button while connecting the BLACK 4-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for 2 seconds. 06 Module RESET completed.
TAKEOVER PROCEDURE - STD KEY - OF PAGE 7 OF 8 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. Press unlock on OEM or aftermarket remote. Insert key into ignition. ACC ON START ACC ON START Turn key to ON position. Press and release BRAKE pedal. 05 Take over procedure completed.
INSTALLATION CHECKLIST - OF PAGE 8 OF 8 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed.