Mekon RV-1 and RV-2 cage ring washers Effective cleaning of cages
Mekon RV-1 cage ring washer Efficient washing float for pressure washing all cage models from Ø 315 to Ø 500 without base ring. The float runs under the collar feet and lies low in the water to avoid unnecessary lifting of the floatation collar. The washer connects to the service boat s existing hydraulics and is operated by radio control. Customer feedback indicates that washing time will be approximately 20-30 minutes when cleaning a 120 m Ø 400 floatation collar. The float itself is made of GRP, with a strong and hygienic surface that prevents dirt and growth attaching itself, and is filled with EPS foam for the lowest possible weight. It can be cleaned while still in the water. RV-1 main dimensions: Length: 5.5 m Width: 4.4 m Buoyancy: 9 000 kg Weight: 2 700 kg Loads: Lifting rings: 1 300 kg - angle tolerance +/- 45 Lifting rings: 7 800 kg - angle tolerance +/- 45 The washer requires a good high pressure pump with a minimum capacity of 500 L/min and working pressure of 230 250 bar. In addition, it can be supplied with external 220V or 400V HPU, supplied in a 400 L stainless steel tank with hour counter mounted.
20-30 min Efficient, non-abrasive floatation collar cleaning
Mekon RV-2 cage ring washer For cleaning all cage models with or without bottom ring. Well equipped and manufactured in high quality materials - for heavy duty use. The RV-2 comes with 4 dimensioned lifting hooks. The float is fitted with fender strips on its outer edge to prevent wear and damage. The RV-2 performs efficient pressure washing of cage models up to Ø 500 with Ø 400 bottom ring, and up to Ø 400 with bottom ring. An extra nozzle is required for larger dimensions, available as an option. The float lies low in the water and runs under all collar feet. The RV-2 comes standard with integrated HPU (220v or 400V) and radio control. Recommended washing time is about 30 minutes for a 120m Ø 400-Ø 500 floatation collar. RV-2 main dimensions: Length: 5.5 m Width: 4.5 m Buoyancy: 11 700 kg Weight: 4 500 kg Loads: Lifting rings: 1 300 kg - angle tolerance +/- 45 Lifting rings: 7 800 kg - angle tolerance +/- 45 The washer requires a good high pressure pump with a minimum capacity of 600 L/min and working pressure of 230 250 bar.
Disinfection: The cage ring washer can be supplied with a booster pump, injectors and separate nozzles for disinfection. The equipment is approved for chemical use and provides a correct dosage in accordance with regulations. The booster pump is installed in the engine room or other suitable place and supplies water to the injector station. The cage ring washer comes with own instructions for cleaning and disinfection of float collars and service boat. For disinfection we recommend a various range of chemicals. Please contact for details. Service agreement Regular service and preventive maintenance help prevent downtime and maintain product performance. Mekon can offer a service agreement tailored to customer needs. Preventive maintenance Yearly check Discount on timer to service technician 24 hour phone support Response time on spare parts Training of personnel The booster pump is not self-sufficient and must be provided of the boat s flushing pump or fire pump. Capacity: This must be 180 l / min and 1.5 bar pressure. The system can also be used for cleaning and desinfiltration of service boat and other equipment. As standard equipment, there is a separate flush for use on a boat. Technical inspection with state reporting In addition, we provide training in equipment and knowledge that shows how our products can help optimize operations.
The versatile Moen NabWork single-hull multi-purpose service vessel, constructed from steel, is specifically designed for use in the aquaculture industry. It is also suitable for heavier duty tasks. The vessel has an impressive bollard pull and positioning capability. Other equipment consists of tried and tested high-quality products. Our NabCat 14.98 x10.00 m single- and twin-deck boats are popular service catamarans intended for use in the aquaculture and service industry. The vessels are wellequipped, with powerful propulsion machinery, Nogva gear and propeller systems, high-capacity crane, and a number of cabins. Our NabCat 13.50x7.50 m is our best-selling boat we have so far delivered more than 60 examples. The vessel is equipped with Scania propulsion machinery and Nogva gear and rotating propeller systems. This contributes to the vessel s excellent manoeuvrability. The boat is equipped with a 32 tm Palfinger crane, and is supplied with a mounting for a small deck winch. Under light ship displacement conditions, this catamaran can reach 15+ knots. The NabWork 10.65x5.00 m is a very popular alternative as a locality boat. It is equipped with powerful propulsion machinery, as well as gear and propeller systems and a generator from Nogva. It is also equipped with side propellers, which gives the boat its excellent manoeuvrability. Our products Our Moen Aquaculture Platform has an impressive feed capacity of 700 tonnes in a silo, as well as a further 200 tonnes cargo capacity and a 100 tonnes silage capacity. It offers flexibility as regards the number of feed lines. The platform has generator operation. The platform also has a large deck area, a substantial storage area and a comfortable accommodation and service section. The Sobit Feed Hatch System makes receiving feed easier and more secure. The system, which is tailormade for both new and existing feed floats, gives you complete control over the feed level in the silos at all times. Upgrading older feed hatches to new Sobit feed hatches can be done quickly and efficiently while maintaining full operation. Moen SkaMik is a rapidly emerging mechanical, gentle and environmentally friendly delousing method. It is chemical-free, so resistance is not a problem. High capacity. Close to 100% removal, collection and destruction of both attached and moving salmon lice. The technology is continually being developed further. Moen Tarpus delousing tarpaulins are made from high-quality materials and are available in various sizes. They primarily consist of certified cargo straps and a strong polyamide fabric. The fabric s breaking and tensile strengths are tested routinely. They are available in three versions: flat, conical and profile. Mekon ring washers are available in two versions: RV-1, intended for washing pens without a bottom ring, and RV-2, for washing pens with a bottom ring. They are self-supporting structures, and are intended for all pen models from Ø315 - Ø500 mm. roksethdesign.no - august 2018 - ID:7184-200x Make a profitable investment Well-anchored in the maritime community Moen Marin AS is a company with solid traditions and a high level of expertise within ship-building with roots dating back to 1923. In addition to traditional production, our ambition is to constantly develop new concepts with a strong emphasis on innovation and user needs. Our focus areas are service vessels and work boats for the aquaculture industry, and we have also developed a new feed float concept in partnership with key players in the aquaculture sector. We are also responsible for the development, marketing and sale of many products related to an industry which is rapidly expanding and developing. Through our presence and international networks, we have forged strong working relationships with enterprises in China, Croatia, Estonia, Latvia and Poland. This strengthens our foundation and competitive edge. Our sister company Moen Marin Service AS has branches in Kolvereid and on Ottersøy near Rørvik. The Kolvereid branch has a slipway, a workshop and a workshop pier, giving it plenty of capacity for servicing, maintenance and repair tasks. Our dry dock (100 x 25 x 8.5m) on Ottersøy near Rørvik is situated close to the shipping channel midway along the Norwegian coast. A new and modern service building has recently been constructed next to the dock. For more information, prices and terms of delivery - contact one of our representatives (see contact list on our website moenmarin.no) or send an e-mail to: salg@moenmarin.no Moen Marin AS l Postal address: Postbox 1287 Sluppen, 7462 Trondheim, Norway l Visit: Havnegt. 9, Pirsenteret (entr. 1, 4th floor), Trondheim www.moenmarin.no