TABLE OF CONTENTS: DOOR CLOSERS v1.4
: Things to Consider:» Type of building» Use of opening» Existing hardware condition» New hardware needed:» Overhead holders» Coordinators» Other» Interior or exterior door» Public entrance or back door» Door width, height, & weight» Door material» Door panel or glass» Degree of opening» Frame / trim» Arm applications» Ceiling clearance» Handing of door» Fire rating» ADA requirements» Environmental considerations» Control» Convenience» Privacy» Security» Energy conservation» Acoustic and noise control Additional Things to Consider: Sized Multi-Sized Cover Arms Specific spring size to width and weight of door available in size 2, 3, 4, 5 or 6 Spring adjustable at time of installation. Sizes 1-6 as per door size Full cover or slim line: plastic or metal Standard arms or heavy duty based on conditions Painted or plated arm and/or covers
» Easy to install» Minimal preparation of door and frame» Accessible to the occasional adjustment that may be necessary with changes in usage or environmental conditions Concealed Closers» Installation requires considerably more door and frame preparation» Closer body mortised above the door in the header» Arm typically mortised into the top rail of the door» Closer and arm are totally concealed when the door is closed Electrified Closers» Installation requires more time due to electrical power requirement» Unit setup is simple» Minimal preparation of door and frame» Electrical power required Rack & Pinion Concealed Electrified
American National Standards Institute ANSI facilitate the development of American National Standards (ANS) by accrediting the procedures of standards developing organizations (SDOs). These groups work cooperatively to develop voluntary national consensus standards. Accreditation by ANSI signifies that the procedures used by the standards body in connection with the development of American National Standards meet the institute s essential requirements for openness, balance, consensus, and due process. ANSI/BHMA A156.4 Door Controls-Closers ANSI/BHMA A156.4-2013 DOOR CONTROLS - CLOSERS Revision of ANSI/BHMA A156.4-2008 https://www.ansi.org/about_ansi/introduction/introduction?menuid=1 Americans with Disabilities Act The Americans with Disabilities Act (ADA) prohibits discrimination against people with disabilities in employment, transportation, public accommodation, communications, and governmental activities. The ADA also establishes requirements for telecommunications relay services. http://www.dol.gov/general/topic/disability/ada
LEED & Sustainability Increasing efficiency in production as well as elevating innovation in products and processes are key strategic drivers for Norton. Continual focus on these initiatives translates to key benefits for our customers and building occupants:» Lower operating costs - many of our products far exceed ANSI/BHMA standards, translating to longer production life and easier maintenance (plus less waste in landfills).» Energy conservation - a clear result of our energy-efficient doors and frames.» Healthier and safer for occupants - comes from our using non-hazardous materials and providing effective life-safety solutions. Sustainability is a driver throughout ASSA ABLOY s value chain; it is an important element in innovation, in sourcing, in production, in employee development, in applying ASSA ABLOY s products and solutions, and in the Group s relation to external stakeholders. Our quality and environmental management systems have achieved ISO9001:2008 and ISO14001:2004 certification. ISO 9001 is the international standard that specifies requirements for a quality management system (QMS). Organizations use the standard to demonstrate the ability to consistently provide products and services that meet customer and regulatory requirements. ISO 14001: 2015 sets out the criteria for an environmental management system and can be certified to. It maps out a framework that a company or organization can follow to set up an effective environmental management system. I can bused by any organization regardless of its activity or sector.
Environmental Product Declarations An Environmental Product Declaration (EPD) documents the cradle-to-grave life cycle of a product and how it affects the environment. An EPD is a verified document that reports environmental data of products based on life cycle assessment (LCA) and other relevant information and in accordance with the international standard ISO 14025 (Type III Environmental Declarations). An important aspect of EPD is to provide the basis of a fair comparison of products and services by its environmental performance. EPDs can reflect the continuous environmental improvement of products and services over time and are able to communicate and add up relevant environmental information along a product s supply chain. EPD s are available on the following Norton products: 1600 Series Closer 5800 Series Operator 6300 Series Operator 7200 Series Closer 8000 Series Closer 9500 Series Closer 5700 Series Closer 6000 Operator 7100 SZ Series Closer 7500 Surface Closer 9300 Series Closer
Health Product Declarations A Health Product Declaration (HPD) is an open standard and format for the accurate reporting of material contents and potential health hazards. AN HPD is a transparent way for manufacturers to disclose contents and ingredients in their products to customers, suppliers, certifiers, and building standards organizations, making for a healthier built environment. HDP s are available on the following Norton products. 7500 Surface Closer 6000 Operator GreenCircle Declarations GreenCircle ensures specificity in third-party certification of manufacturer s sustainability claims. GreenCircle s rigourous evaluation process provides trusted transparency that a manufacturer s product claims are authentic. GreenCircle is recognized by the USGBC Leadership in Energy and Environmental Design (LEED) and NAHB National Green Building Standard Program. Norton GreenCircle Certifications include: Products verified to reduce energy consumption 5800 ADAEZ (wireless) 5800 ADAEZ (plug-in) 6000 Series Sustainable manufacturing practices Monroe, NC facility
Declare Labels Declare Labels are like a nutrition/ingredient label for your product, and help with the ever growing Living Building Challenge (LBC). Consumers are demanding a new kind of information about the products they buy. They want to know what s in the air they breathe, the food they eat and the buildings they occupy. By offering a platform for public disclosure that surpasses any other material label, the Declare Labels Norton provides can enable a deep connection between suppliers and consumers. Below are the Declare Labels for Norton Products: 7500 Surface Closer 6000 Operator
LEED Certification The Leadership in Energy and Environmental Design (LEED) Green Building Rating System is the nationally accepted benchmark for design, construction, and operation of high performance green buildings. Norton can help facilities to achieve prerequisites and accumulate points toward LEED certification. Learn more. Norton Product Post-Consumer Recycled Content* Pre-Consumer Recycled Content** Total LEED Recycled Content Percentage 78B/F Potbelly Closer 52% 0% 52% 1600 Aluminum Closer 88.8% 0% 88.8% 1700BC Aluminum Closer 52% 0% 52% 2800ST Cam Closer 59% 0% 59% 5600 Operator 82.8% 0% 82.8% 5700 Operator 71.9% 0% 71.9% 5800 Operator 75% 0% 75% 6000 Operator 72% 0% 72% 6300 Operator 83% 0% 83% 7100SZ SafeZone 88.6% 0% 88.6% 7200 77% 0% 77% 7500/7700 Aluminum Closer 78.3% 0% 78.3% 7900 Overhead Closer 52% 0% 52% 8000 Aluminum Closer 80.1% 0% 80.1% 9300BC Aluminum Closer 52% 0% 52% 9500 Cast Iron Closer 91.1% 0% 91.1% *Recycled content defined in accordance with industry standards. **Pre-consumer recycled content refers to waste material that is immediately placed back into the production cycle. Waste materials generated by the production of these products are collected and shipped off site where it then reenters the recycle stream. ***Must specify if a metal or ABS cover is needed for 7500 or 8000 closers. Use M for metal, G for ABS.
End-of-Life Recycle Program Norton encourages environmentally responsible practices for processing and disposing of products that have reached the end of their useful life. In support of these practices, Norton is announcing the availability of a Product End-of-Life (PEOL) Recycling program. This free program provides recycling and/or disposal of Norton products that have reached the end of their life cycle and are beyond the product s warranty period. To participate in this program, see the directions below:» All returns for recycling must be pre-approved and have a Returned Goods Authorization (RGA) prior to shipping. We reserve the right to limit or refuse any request. Contact Customer Service at 1-877-974-2255 for an RGA form.» Only Norton products may be returned and they must be free from other building materials attached to the products.» After the RGA has been approved, send products to: Norton Door Controls 3000 Highway 74 East Monroe, NC 28112 Notes:» No credits or exchanges will be issued.» All packing, freight and handling expenses are the sole responsibility of the sender. For additional information, contact your ASSA ABLOY Door Security Solutions sales consultant, call Norton at 877-974-2255 or visit www.nortondoorcontrols.com.
ANSI APPLIED STOP BACKCHECK CLOSING FORCE CONCEALED IN DOOR CUTOUT CYLINDER ASSEMBLY DELAYED ACTION DOUBLE LEVER ARM FINISH PLATE FOREARM HANDED HOLD-OPEN ARM HYDRAULIC FLUID American National Standards Institute which publishes standards for the entire door opening Surface mounted stop attached to a cased opening frame Hydraulic circuit designed to cushion the doors opening swing at about 70 to 75 degrees Energy generated by a closer to close and latch the door Closer with the cylinder concealed in the top rail of the door with either an exposed or concealed arm Preparation of the top rail of a door or frame for concealment of the closer, arm, or track Main closer component complete with any mounting plates or electronics Delays closing from maximum opening to approximately 70 to 75 degrees A two part arm hinged at the elbow that provides superior leverage. Decorative plate applied to overhead concealed closer to conceal closer mounting plate and screws Arm part that connects main arm to the shoe attachment in a double lever arm system Closer is designed for only right or left swing doors Double lever arm that provides hold-open function, adjustable at elbow or shoe Oil metered by valve system to control door
LATCH LATCH SPEED MAIN SPEED MAXIMUM OPENING MULTI-POINT HOLD OPEN NON-HANDED NON-SIZED OPENING FORCE OVERHEAD CONCEALED PARALLEL ARM REGULAR ARM REGULATING SCREW Allows adjustment of door speed from 10-12 to closed position Separate adjustment that controls the last few degrees of the doors degrees of latch Adjustment to control closing swing of the door to within a few degrees of latch Furthest degree of door opening allowed by the mechanical limits of the closer Infinite hold-open points from 0 up to the maximum opening Closer is designed for both right and left hand swinging doors Cylinder assembly with spring power adjustable over a range of sizes Force required to open door against the closers spring power Closer with cylinder concealed in head frame and either a concealed or exposed arm The closer is mounted on the push side of the door. The arm is attached to the frame soffit parallel to the door. The closer is mounted on the pull side of the door. The arm is attached to the frame face or hinge side of the door. Valve that adjusts flow of hydraulic fluid within cylinder to control door closing speed
SHOE SIZED SOFFIT SPRING POWER STANDARD COVER STANDARD CYLINDER STANDARD TRACK WITH BUMPER STANDARD TRACK SWEEP TOP JAMB ARM TRACK BUMPER TRI-STYLE Attaches forearm to frame or door face in a double lever arm system Closer with a specific minimum closing power Horizontal surface of a frame between vertical stops on a double rabbeted frame Closing force exerted by the spring inside cylinder to close door Conceals cylinder with only arm/pinion attachment exposed Cylinder with main speed, latch speed, and backcheck adjustments Non-hold open track with bumper assembly installed Non-hold open track Provides adjustment of door speed from full opening position to 10-12 from the closed position The closer is mounted on the opposite to hinge side frame face, above the door. The arm is attached to the top rail of the door at a right angle to the door. Mounts in track to cushion opening swing, but reduces maximum opening The closer is packed with all necessary hardware for mounting in any of the three traditional mounting styles: Regular Arm, Parallel Arm or Top Jamb
Basic function of a closer: provide smooth control through the opening cycle of the door as well as the closing action after the door has been released.» As door opens, closer arm transmits motion to the piston in the closer housing» Compresses the spring which provides energy to close the door» Force generated by compressed spring is governed by hydraulic circuit in the closer» Opening cycle: gear teeth of pinion engage with gear teeth of rack milled into piston» As pinion rotates, spring is compressed» Movement of piston forces hydraulic fluid from reservoir side to flow to area vacated by piston.» Regulating flow controls door s closing speed» Closing cycle: compressed spring moves piston to it s original position; reversing flow of hydraulic fluid
» Two points of control in hydraulic fluid passage during the closing cycle: sweep and latch speed» Sweep speed of closing short of the last 10-12» Latch last 10-12 of closing» Desirable sweep is generally medium to low (4-6 seconds)» Desirable latch varies depending on the door/application
Anatomy of a Closer Door Closer Cutaway View 1 Back- check Adjustment Valve Spring Power Adjustment Backcheck Posi<oning Valve 2 Spring chamber 3 4 Precision Ground Piston Sweep/Delayed Ac<on Valve 5 Sweep Valve (only with DA) 6 Latch Speed Valve Rack Aluminum alloy body
DOOR CLOSERS Spring Power 1 Spring Adjustment Provides adjustment between size 1 thru size 6 on mul7- sized closers Sized closers can be adjusted 50% up or down Product Enhancements 2 3 1 4 5 6
Opening Cycle Adjustment 60-85
Opening Cycle Adjustment opening cycle
Closing Cycle Adjustment Provides adjustment of door speed from full opening position to 10-12 from the closed position
Closing Cycle Adjustment
Closing Cycle Adjustment Allows adjustment of door speed from 10-12 to closed position
» Regular Arm, Top Jamb and Parallel Arm» The method the architect chooses is influenced by some combination of these five factors:» Closer position, relative to the locations of door, frame and hinges» Space limitations on the top rail of the door» Space limitations on the frame face above the door» Appearance» Accessibility of the closer arm Regular Top Jamb Parallel
Mounting Options Regular Arm Advantages:» Less space on door s top rail than parallel arm installation» Maximum power for larger doors» Easy installation» Allows door to swing 180 degrees» Mounted on pull side of the door Disadvantages:» Not suitable for external doors Parallel Arm Advantages:» Forearm mounts to underside of frame (soffit) with a soffit plate no space required on frame face» Parallel arm is less subject to tampering» Depth of door s top rail must be considered» Slightly less power-efficient than regular arm mounting Disadvantages:» Provides 25-30% less power than standard applications» Larger top rail required Top Jamb Advantages:» Good choice for exterior doors» Handles large reveals» Allows door to swing 180 degrees» Installs on push side of door» Suitable for doors with narrow top rails (aluminum storefronts) Disadvantages:» Appearance may be objectionable» Space needed on frame for mounting closer
Mounting Options Track Mounting» Closer is mounted on either the hinge side or opposite hinge side» Slide track is mounted to the frame face on the hinge side and frame soffit on the opposite to hinge side Track Mounting Advantages» Clean appearance» Allows for features such as holders without compromising appearance» Track applications can be mounted on the push or pull side of the door Disadvantages» Least efficient application» Difficult to comply with ADA*» Not to be used on exterior doors * Except Cam Action Closers
Special Mounting Options Corner Brackets:» Installation when the closer cannot be mounted to either the door or the frame» Bracket is mounted on the upper corner of the push side hinge jamb of the frame» Closer is mounted to the bracket; arm is attached to the top rail of the door at a right angle to the door
Handing Viewing the Door from the Stop/Push Side» Hinges on the Left = Left Hand Door» Hinges on the Right = Right Hand Door
Door Closers Selection Guide HIGH USE MODERATE USE LOW USE 160 Aluminum Light-Duty 210 Aluminum Light-Duty 1700 Aluminum Light-Duty 1600 Aluminum Medium-Duty 78-B/F Aluminum Light-Duty 8000 Aluminum Medium-Duty 2800ST* Cam Action Heavy-Duty 410 Cast Iron Medium-Duty 7500 Aluminum Heavy-Duty 9500* Cast Iron Heavy-Duty * 2800ST and 9500 Series Closers are primarily specified. All others are for both specified and discretionary projects. FEATURES
Product Overview Chart 9500 9540 410 7500 7570 Aluminum Cast Iron Cam Action Overhead Concealed EM 8301/ 8501 1601 1700BC 210 160 78B/F 2800ST 7900 7100SZ 7200 7700PT
Product Comparison CERTIFICATION & WARRANTY CAST IRON ALUMINUM 9500 9540 410 2800ST 7500 8000 1600 1700BC 78B/F 210 160 ANSI/BHMA A156.4 Grade 1 Grade 1 Grade 1 N/A Grade 1 Grade 1 Grade 1 Grade 3 Grade 3 Grade 1 Grade 1 UL & ULC Listed Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Warranty 25 Year 25 Year 10 Year 10 Year 25 Year 25 Year 25 Year 5 Year 10 Year 10 Year 5 Year Extended Cycle Testing 25 Million Per Standard Per Standard N/A 25 Million 25 Million 25 Million Per Standard Per Standard Per Standard Per Standard End of Life Recycling Program Available SIZE & CONSTRUCTION Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Construction (Body) Cast Iron Cast Iron Cast Iron Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Mounting Hole Pattern 1" x 10" 2-1/4" x 5"* 2-1/4" x 5"* 1"x 11-1/8" 2-3/8" x 6-3/4" 3/4" x 12" 3/4" x 9-1/16" 3/4" x 8" 4-1/8" x 1-3/8" 3/4" x 12" 3/4" x 9-1/16" Spring Size Adjustable 1-6 Adjustable 1-6 Adjustable 1-6 Adjustable 1-6 Adjustable 1-6 Adjustable 1-6 Adjustable 1-6 Size 3, 4 Size 2, 3, 4 Size 2-4; Size 5-6 Adjustable 1-6 Adjustable 1-4 Size 4 Closer Body (Handing) Non-Handed Non-Handed Non-Handed Non-Handed Non-Handed Non-Handed Non-Handed Non-Handed Handed Non-Handed Non-Handed Standard Backcheck Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes OPTIONS Plastic Cover Standard Standard Standard Standard Standard Standard Optional Optional No Standard Optional Metal Cover Option Optional Optional No No Optional Optional No No No No No Slim Line Cover Option No No No No No Optional No No No No No Delayed Action Option Yes Yes Yes No Yes Yes No No Yes No No Sex Nuts & Bolts (Tri-Style pack) Optional Optional Standard Optional Optional Optional Optional Optional Optional Standard Standard Multiple Multiple 689, 690 only Multiple Multiple Multiple Multiple 689, 690 only Multiple 689, 690 only 689, 690 only
Product Comparison APPLICATION / ARM TYPE AVAILABILITY CAST IRON ALUMINUM 9500 9540 410 2800ST 7500 8000 1600 1700BC 78B/F 210 160 Regular Top Jamb Parallel Regular Rigid Parallel Rigid CloserPlus CloserPlus Spring CloserPlus Ramp Cushion Stop Unitrol Low Profile Slide Track *Retrofit LCN4040XP
Competitive Products Cross Reference ARCHITECTURAL COMMERCIAL NORTON LCN Dorma PDQ Cal Royal Stanley Falcon Hager 9500 4040XP X X X X X X 7500 4050 8900 X X D4550 SC70A X 8501 1460-72FC 8600 5500 X D3551 X X 8301 1460-72 8600 5300 X D3550 X X 1600 1260X 7400 X X D1650 X X 1700 X TS77 X X X SC90A X 9300 X 640 X 700 D1650 X 5400 2800ST X TS93 X X X X X 78B/F X X X X X X X 410 X X 7100 CR441 QDC112 X 5100 210 1450 X 5100 900/800 QDC211 SC80A 5200 160 1250 7300 3100 300/400 QDC311 SC60A 5300 NOTE: No two products are exactly alike. This cross reference represents our judgment of products that are most similar. Information has been obtained from trade sources. It is not represented nor guaranteed that any product exactly equals any other products.
Cast Iron Closers 9500 Series» Premium closer» New construction 9540 Series» Premium closer for replacement opportunities» Replacement for LCN 4040XP 410 Series» Lower price point» Same footprint/direct replacement for LCN 4040XP
Cast Iron Closer 9500 Series Features» Cast iron closer body» Adjustable spring sizes 1-6» Heavy-duty arms available: Regular Rigid, Parallel Rigid, CloserPlus, Parallel Rigid Offset and Unitrol» Slide Track: push or pull side mounting» Closer mounting plate for easy installation» 25+ million cycles» 25-year limited warranty Certifications» ANSI/BHMA A156.4 Grade 1 certified» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test» Complies with requirements for the Americans with Disabilities Act (ADA) and ANSI standard A117.1 Market Segment» Government» Industrial» Institutional
Cast Iron Closer 9540 Series Features» Cast iron closer body» Adjustable spring sizes 1-6» Mounting bracket for retrofit applications» Non-hold open» 25-year limited warranty Certifications» ANSI/BHMA A156.4, Grade 1 certified» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test» Complies with requirements for the Americans with Disabilities Act (A.D.A) and ANSI standard A117.1 Market Segment» Government» Industrial» Institutional
Cast Iron Closer 410 Series Features» Cast iron closer body» Adjustable spring sizes 1 6» Optional arms: Heavy-duty arm with removable stop, heavy-duty arm with removable stop and spring buffer» Same footprint/direct replacement for LCN 4040XP» 10-year limited warranty Certifications» Certified for ANSI/BHMA A156.4 Grade 1» UL/cUL listed for use on fire rated doors» UL10C listed for positive pressure fire test» Meets requirements for Americans with Disabilities Act (ADA) and ANSI/BHMA A117.1 Market Segment» Industrial» Institutional» Commercial
Aluminum Closer 7500 Series Features» Cast aluminum closer body» Adjustable spring sizes 1-6» Heavy-duty arms: Regular Rigid, Parallel Rigid, CloserPlus, CloserPlus Spring and Unitrol» Slide Tracks: push or pull side mounting» Corrosion resistant model available (specify 7500SS)» 25+ million cycles» 25-year limited warranty Certifications» ANSI/BHMA A156.4, Grade 1 certified» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test» Complies with requirements for the Americans with Disabilities Act (A.D.A) and ANSI standard A117.1 Market Segment» Government» Industrial» Institutional
Aluminum Closer 7570 Series Features» Cast aluminum closer body» Adjustable spring sizes 1-6» Heavy-duty arms: Parallel Rigid, CloserPlus, and CloserPlus Spring» Slide Tracks: push or pull side mounting» 25-year limited warranty Certifications» ANSI/BHMA A156.4, Grade 1 certified» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test» Complies with requirements for the Americans with Disabilities Act (A.D.A) and ANSI standard A117.1 Market Segment» Government» Industrial» Institutional
Aluminum Closer 8000 Series Features» Cast aluminum closer body» Adjustable spring sizes 1-6» Heavy-duty arms available: Parallel Rigid, CloserPlus, CloserPlus Spring and Unitrol» Slide track - push or pull side mounting» Available with full or slim line cover» 25+ million cycles» 25-year limited warranty Certifications» ANSI/BHMA A156.4, Grade 1 certified» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test» Complies with requirements for the Americans with Disabilities Act (A.D.A) and ANSI standard A117.1 Market Segments» Government» Industrial» Commercial
Aluminum Closer 1600 Series Features» Cast aluminum closer body» Adjustable sizes (1-6) and fixed sizes (3 or 4) available» Heavy-duty arms: Parallel Rigid, CloserPlus, CloserPlus Spring, Closer Stop and Unitrol» Corrosion resistant model available (specify 1601SS)» 25+ million cycles» 25-year limited warranty Certifications» ANSI/BHMA A156.4, Grade 1 certified» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test» Complies with requirements for the Americans with Disabilities Act (A.D.A) and ANSI standard A117.1 Market Segments» Institutional» Commercial» Retail
Aluminum Closer 1700 Series Features» Cast aluminum closer body» Spring size 1, 2, 3, or 4» Installs regular arm, parallel arm or top jamb» 5-year limited warranty Certifications» ANSI/BHMA A156.4 Grade 3 certified» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test Market Segments» Commercial» Retail» Multi-Housing
Aluminum Closer 78B/F Series Features» Cast aluminum closer body» Adjustable spring power» B/D - Spring size 2, 3, or 4» E/F - Spring size 5 and 6» 10-year limited warranty Certifications» ANSI/BHMA A156.4, Grade 3» UL / cul listed for use on fire rated doors Market Segments» Industrial» Commercial» Retail
Aluminum Closer 210 Series Features» Cast aluminum closer body» Adjustable spring size 1-6» Full plastic cover» Optional heavy-duty arm with removable stop» 10-year limited warranty Certifications» ANSI/BHMA A156.4, Grade 1» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test» Meets requirements for Americans with Disabilities Act (ADA) and ANSI/BHMA A117.1 Market Segments» Commercial» Retail» Multi-Housing
Aluminum Closer 160 Series Features» Cast aluminum closer body» Adjustable sizes (1-4) and fixed size (4) available» Hold open arms available for 161BF only» 5-year limited warranty Certifications» ANSI/BHMA A156.4, Grade 1» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test» Meets requirements for Americans with Disabilities Act (ADA) and ANSI/BHMA A117.1 Market Segments» Commercial» Retail» Multi-Housing
Aluminum Cam Action Series 2800ST Series Features» Cast aluminum closer body» Adjustable spring size 1 through 6» Slide track application with regular arm operating efficiency» Push or pull side mounting» 10-year limited warranty Certifications» Meets requirements for Americans with Disabilities Act (ADA)» UL / cul listed for use on fire rated doors Market Segments» Industrial» Institutional» Commercial https://www.youtube.com/watch?v=sikfimbxfqi&feature=youtu.be
Heavy Duty Arms Aluminum Closers Heavy-Duty Arms Unitrol (UNI) CloserPlus Spring (CPS) CloserPlus (CLP) Parallel Rigid (PR) Regular Rigid (R) Buffer Spring Stop» Combines the features of a overhead door stop/holder with the backcheck feature of the door closer» Heavy traffic / high abuse areas; reduces door stopping shock loads» MOST controlled stop available» Door opens; forces go into frame. Other heavy duty arms rack the frame» Incorporates all CLP arm features with an added buffer spring» Heavy traffic and moderate abuse areas» Buffer spring is compressed prior to the arm hitting dead stop point» Incorporates a stop at the arm s soffit plate» For applications that do not allow auxiliary door stops; heavy traffic and moderate abuse areas» Dead stops the door at a predetermined degree of door swing» Heavy duty arm» Heavy traffic areas» Applications require auxiliary door stops» Heavy duty arm» Non-adjustable secondary arm
Heavy Duty Arms Aluminum Closers Ramp Hold Open Arm (CLP-R)» Patented design - ramp and plunger» Exceptional service life» Heavy duty, dead stop arm» Plunger easily slides into place reducing wear and tear on the arm» Available on the 7500 and 8000 Series Ramp
Heavy Duty Arms Aluminum Closers Cushion Stop Arm (CA)» Protects door and frame in applications where auxiliary stop cannot be used and moderate abuse is anticipated» Prevents overextension of arm» Regular arm mounting» Non-hold open applications» Allows door to swing 85 and 110 based on templating» Available with 1600 Series
Heavy Duty Arms Cast Iron and Aluminum Closers Arm Assemblies Overview Cast Iron Aluminum 9500 9540 410 7500 8301/ 8501 1600 1700BC 78B/F 210 160 Regular Top Jamb Parallel Regular Rigid Parallel Rigid CloserPlus CloserPlus Spring CloserPlus Ramp Cushion Stop Unitrol Low Profile Slide Track
Closer 7900 Series Features» Closer concealed in the header» Adjustable spring sizes (1-6) and fixed sizes (4, 5 or 6) available» Fully adjustable, multi-point hold open (7900)» Shock-absorbing door stop» Handed» Can be used with butt hinges, offset or center hung pivots» Installs in hollow metal, aluminum or wood doors and frames» 10-year limited warranty Certifications» ANSI/BHMA A156.4, Grade 1 certified» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test Market Segments» Industrial» Institutional» Commercial
Closer 7200 Series Features» Multi-point hold open» Fixed spring sizes 3, 4 or 5» Push or pull side mounting» Handed» Selective Hold Open allows door to hold open at any degree of opening beyond a pre-set hold open point, up to 175» Voltage - 24VAC/DC or 120VAC» Detectored or non-detectored units» 2-year limited warranty Optional Features» Radio Frequency - RFS (selective) - RF units are not UL listed for fire doors» Free Swing arm (7240 pull side only)» Infinite Hold Open (optional) - door will hold open at any degree of opening up to 175. Infinite Hold Open can be set in the field by turning the cam. Functions» Master Unit: Suffix MPDO» Slave/Support Unit: Suffix MPSO» Executive Unit: Suffix RFS Certifications Certifications» ANSI/BHMA A156.15 certified» UL / cul listed for use on fire rated door» UL10C listed for positive pressure fire test
Closer 7700PT Power Track Features» Selective single-point hold open» Fixed spring size 5» Push or pull side mounting» Handed units» 24 VAC/DC or 120VAC, 60Hz» 2-year limited warranty Functions» Master Unit Suffix PTDO» Support Unit Suffix PTO Certifications Certifications» ANSI/BHMA A156.15 certified» UL listed (All Support units are UL listed for application with any compatible UL listed fire/smoke detection equipment)
Closer 7100SZ Series SafeZone Features» Multi-point, electromechanical closer/holder» Fixed spring sizes (2, 3, 4 or 5) available» Push or pull side mounting» Handed units» Sensor detects movement in both directions» Selectable hold open time and sensitivity» 2-year limited warranty Certifications» Certified to meet ANSI/BHMA A156.15 Release Devices» UL / cul listed for use on fire rated doors» UL10C listed for positive pressure fire test» Specific models comply with requirements for the Americans with Disabilities Act (A.D.A) and ANSI standard A117.1 Benefits» Reduces the chance that someone will get hit by closing door; door held open as long as movement is detected» Reduces the likelihood the door will be propped open, providing higher security for the facility» Energy Efficiency - The door is open only as long as it needs to be reducing potential for excessive heat loss and maintaining proper compartmentalization» Fewer door opening cycles are required while a stream of people move through the opening, increasing the life of the opening
BSP Black Suede
3 DOOR CLOSERS 2-3/8 6-3/4 13-1/4 3/4 12 Date Code - underneath; not shown (2 Alpha Characters) 1-6 = Blank 2 = 8302/8502 3 = 8303/8503 4 = 8304/8504 5 = 8305/8505 6 = 8306/8506 7500/7700 SERIES Standard 7500 = 4 valves (S/D, L, P&B) Delayed Action 7500DA = 5 valves (S/D, S, L, P&B) 1-6 S S/D P B LISTED 149A R668 R785 DOOR CLOSER BODY Closer Size Closer Size Date Code (2 Alpha Characters) 1-6 = 7500 2 = 7702 3 = 7703 4 = 7704 5 = 7705 6 = 7706 8000 SERIES FA
3/4 3/4 9-1/16 Older 1601 models may be stamped "BF". They can be replaced with the "1-6" model. 8 1-6 = 1601 2 = 1602BC 3 = 1603BC 4 = 1604BC 5 = 1605BC 6 = 1606BC Closer Size 3-6 BE 1600 SERIES Date Code (2 Alpha Characters) 7500/7700 1700 SERIES SERIES Closer Size 1 = 1701(BC) 2 = 1702(BC) 3 = 1703(BC) 4 = 1704(BC) 3 KC Date Code (2 Alpha Characters)
A - January B - February C - March D - April E - May F - June G - July H - August I - September J - October K - November L - December M - 1995 L - 1996 K - 1997 J - 1998 I - 1999 H - 2000 G - 2001 F - 2002 E - 2003 D - 2004 C - 2005 B - 2006 A - 2007 Z - 2008 Y - 2009 X - 2010 W - 2011 V - 2012 U - 2013 T - 2014 S - 2015 R - 2016 Q - 2017 P - 2018 O - 2019 N - 2020 Example: for closers are signified by a combination of two (2) letters. The first letter is the month the second letter is the year. For example, a date code of CS = March 2015
RESOURCES Norton offers educational resources and tools to help guide in the selection, sale and installation of door closers:» ASSA ABLOY Academy Trainings [https://assaabloyds.csod.com/globalsearch/search.aspx?s=1&q=door%2520closer#q=door%2520closers&s=1&a=]» Presentations [link https://extranet.assaabloydss.com/extranet/library/presentations/index.cfm?brand=n] (must first log into extranet to access)» Brochure [https://content.assaabloyusa.com/doc/aadss1054162&.pdf]» Sell Sheets: Architectural Openings [http://content.assaabloyusa.com/doc/aadss1047037&.pdf] Aluminum Storefronts [http://content.assaabloyusa.com/doc/aadss1047036&.pdf]» Instructional and Promotional Videos [https://www.nortondoorcontrols.com/en/site/norton/library/videos/] 43412-05/18