TABLE OF CONTENTS Bulb Specifications and Functional Check...13-2 Location of Exterior Lamps...13-3 Replacing the Exterior Lamps...13-4 Replacing the Interior Lamps...13-6 13 Lamp 1 2 3 4 5 6 7 8 9 10 11 12 13 14
BULB SPECIFICATIONS AND FUNCTIONAL CHECK 1 BULB SPECIFICATIONS FUNCTIONAL CHECK 2 3 4 5 6 7 8 9 10 11 12 13 Exterior Interior Description Numbers Specification Head High beam 2 H1-55W Low beam 2 H7-55W Turn signal 2 P21W Position - LED Front fog light 2 H16-19W Rear fog light 2 21W Side repeater - LED Rear combination Tail - LED Turn signal 2 PY21W Back-up 2 W16W Stop 2 P21W License plate 2 W5W High mounted stop - LED Puddle 2 LED Front room 2 10W Glove box 1 5W Center room 1 10W Luggage 1 10W Door courtesy 2 5W 111 Check whether the comes on or off by turning its switch. 222 Check the corresponding fuse when the doesn t come on. 333 If the fuse is blown, replace it with a new one. 444 For replacing procedures, refer to the In Case of Emergency section in this manual. 555 If the fuse is not blown, check the bulb and replace it with a new one if needed. 666 If the bulb is not defective, have the system checked by a Ssangyong Dealer or Ssangyong Authorized Service Center. Caution y Use only a specified capacity bulb for replacement. y Disconnect the negative cable on the battery before replacing the bulb. Remove the ignition key. y Do not apply excessive force to remove the bulb cover. y Make sure that the corresponding switch and the ignition switch are turned off before replacing a bulb. y Do not touch a bulb with bare hands immediately after turning off the. y Do not touch a bulb with bare hands. Fingerprints, dust, or moisture stuck to the bulb may shorten its life or cause it to explode. If you accidentally touch the bulb, wipe the bulb glass with a soft cloth. y Never try to adjust the head aiming angle. It should be done by a qualified technician in a Ssangyong Dealer or Ssangyong Authorized Service Center. 14 13-2 Lamp
LOCATION OF EXTERIOR LAMPS High mounted stop Side repeater License plate Front fog light Puddle Head (Low beam) Turn signal Stop Tail Back-up Turn signal Head (High beam) Tail, DRL (EU)* Stop, Rear fog light (EU) Lamp 13-3
REPLACING THE EXTERIOR LAMPS REAR COMBINATION LAMP 111 Remove the ignition key from the key cylinder. 222 Open the tailgate. 333 Disconnect the two mounting bolts from the rear combination. Back-up Stop Turn signal Rear fog light 444 Remove the rear combination from the body. 555 Turn the bulb housing to remove it. 666 Remove the bulb while pushing and turning it. 777 Replace it with a new one. 888 Install in the reverse order of removal. Rear combination 13-4 Lamp
LICENSE PLATE LAMP 111 Remove the ignition key from the key cylinder. 222 To take out the license plate light assembly, remove the two fastening screws on the license plate light and push the assembly downward. 333 Remove the housing by turning the connector. 444 Remove the bulb. 555 Replace it with a new one. 666 Install in the reverse order of removal. License plate Lamp 13-5
REPLACING THE INTERIOR LAMPS Front Room Lamp Center Room and Luggage Room Lamps 111 Remove the ignition key from the key cylinder. 222 Cover the tip of a flat blade screwdriver with a cloth and insert the tip into a cover slot. Then, pry off the cover. 333 Replace the bulb with a new one. 444 Install the cover. 111 Remove the ignition key from the key cylinder. 222 Cover the tip of a flat blade screwdriver with a cloth and insert the tip into a cover slot. Then, pry off the cover. 333 Replace the bulb with a new one. 444 Install the cover. Caution The cover should be pried up from the rear section (indicated by the arrow). Otherwise, the cover may be damaged. 13-6 Lamp
Glove Box Lamp Door Courtesy Lamp 111 Remove the ignition key from the key cylinder. 222 Open the glove box. 333 Open the cover as shown in the figure. 444 Replace the bulb with a new one. 555 Install in the reverse order of removal. 111 Remove the ignition key from the key cylinder. 222 Cover the tip of a flat blade screwdriver with a cloth and insert the tip into a cover slot. Then, pry off the cover. 333 Replace the bulb with a new one. 444 Install the cover. Lamp 13-7
MEMO