Daikin McQuay. Centrifugal Chiller Single Compressor WSC, TSC, HSC 048, 050. Last Manufactured: 2008

Replacement Parts List No. 700000000 Revision N 09/2018 Daikin McQuay Centrifugal Chiller Single Compressor WSC, TSC, HSC 048, 050 Last Manufactured: 2008 To find your Daikin Applied parts distributor, call 1-800-377-2787 or visit www.daikinapplied.com

Contents Parts List Revision History... 3 Nomenclature Dataplate Locations... 4 Unit Dataplate... 5 Model Number- Unit... 5 Style Number- Unit... 5 Serial Number- Unit... 5 Model Number- Complete... 6-10 Electrical Legend...11 Control Box- MicroTech 200 Mounting of Unit Control Panel and Lube Box... 12 Front Panel & Inside of Micro Control Door Assembly... 13 Interior Panel... 14 Interior Panel... 15 Sensors... 16 Compressor Lube Box Assembly... 17-18 Control Box- MicroTech II Unit Control Box Mounting... 19 Compressor Control Box Mounting... 20 Unit Control Box Detail-Until 5/05... 21-22 Unit Control Box Detail- 5/05 and Later... 23-24 Compressor Control Box Detail... 25-26 4- Way SA/SB Solenoid Valve & Tubing- Until 7/05... 27 4- Way SA/SB Solenoid Valve & Tubing- 7/05 and Later... 28 Cables and Sensors... 29-30 Starter- Factory Installed- Units with MicroTech 200 Control Box... 31 Starter, Compact - Factory Installed- Units with MicroTech II Control Box... 32 Starter, Mini Cabinet- Factory Installed- Units with MicroTech II Control Box... 33 Starter, Free Standing - Field Installed- Units with MicroTech 200 Control Box... 34 Starter, Free Standing - Field Installed- Units with MicroTech II Control Box... 35-36 Differential Pressure Switch... 37 Hot Gas Bypass- Until 10/02... 38 Hot Gas Bypass- 10/02 to Present... 39 Condenser & Evaporator Valves... 40 Liquid Line - Thermal Expansion Valve... 41-45 Unit Insulation... 46 Condenser Nomenclature... 47 Dataplate... 47 Heads... 48 Sight Glass, Flange, Tubes, Head Gaskets... 49 Gaskets- Dish Head... 50-51 Gaskets- Water Box Heads... 52-53 Evaporator Nomenclature... 54 Dataplate... 54 Heads... 55 Sight Glass, Flange, Tubes, Head Gaskets... 56 Gaskets- Dish Head... 57 Gaskets- Water Box Heads... 58 Compressor Nomenclature... 59 Model Number- Compressor... 59 Style Number- Compressor... 59 Motor Style Number... 59 Mounting Brackets and Hardware... 60 Motor Drain Line, Motor Cooling Line, Oil Cooler Drain... 61-62 Suction & Discharge Lines, Suction Victaulics, Seals, Discharge Nozzle, Flanges, Check Valve... 63-65 Front End- Inlet- Section, Vanes, Piston, Cone, Seals... 66 Main Gear Train- Hi Speed Section, Impeller, Hi Speed Gear, Volute, Seals... 67-69 Gears- High Speed (Pinion) & Low Speed (Bull)... 69 Main Gear Train- Low Speed Section- Low Speed Gear, Lock Plate, Bearings, Seals... 70 Gear Cover, Deflector, Lee Plug, Pipe Plugs... 71 Crankcase Heater... 71 Oil Circuit & Spin Down, Oil Cooler, Spin Down Piston, Valves, Oil Lines, Mist Eliminator, Seals... 72-74 Oil... 74 Oil Pump... 75 Motor Section... 76-78 Motors- Stators, Rotor/Shaft Assembly... 78 Critical Parts List... CPL1 RPL 7000000 / Page 2

Parts List Revision History Revision Date Description A thru I Revision history details archived. J 04/12 Page 6- Corrected Code 10 to Code E (was D) = Marine Box-Flanged. Page 18- Expanded and clarified info for OITS panel. Removed Ref. 303. Page 21- Corrected retrofit kit p/n to 300040547 (was 300040573) in footnote *. Page 26- Added Until 7/05 to title. Page 27- Added page for 4-Way SA/SB Solenoid Valve & Tubing, 7/05 & later. Page 32- Removed Ref. 110 Cover Plate and Ref. 111 Screw. Pages 48,49- Removed Condenser Head p/n info (deleted 2 pages). Added note to contact McQuay Parts for Head p/n s. Added page to expand and clarify info for Ref. 352 Head Gaskets. Pages 51,52- Removed Evaporator Head p/n info (deleted 2 pages). Added note to contact McQuay Parts for Head p/n s. Added page to expand and clarify info for Ref. 352 Head Gaskets. Page 58- Removed italic text and Note pertaining to italic text. Added footnote 9. Page 60- Added Ref. 144 Brass Union (until 7/05), Fitting (7/05 & later). Added footnote 3. Page 63- Corrected descriptions for Ref. 438 to Bearing- Pinion, Rear and Ref. 440 to Bearing- Pinion, Front. Page 71- Corrected footnote 3 to...contact McQuay Parts... (was SMG). K 5/15 Update cover, logo, tagline & add CPL1 to Contents. Pages 47, 50, 67 & 70 Change contact McQuay Parts to contact Daikin Applied. CPL1- Add Critical Parts List. L 11/16 Page 18: Corrected descriptions for Ref. 15 OITS Cables. Added Power Cord w/ac Adapter. Pages 21 and 23: Updated description for BACnet to MS/TP, was RS232. Page 51: Corrected description for Evaporator Gaskets. Page CPL1: Updated CPL. M 12/17 Cover: Added Last Manufactured date. N 09/18 Major overhaul of content. Updated, corrected and added various part numbers. Removed many tubing and piping part numbers. Updated Model Number- Complete nomenclature. Updated CPL page. Daikin Applied, 13600 Industrial Park Blvd., P.O. Box 1551, Minneapolis, MN 55440 (763) 553-5330 RPL 7000000 / Page 3

Nomenclature Dataplate Locations Unit Dataplate Unit Dataplate End View- MicroTech 200 Units End View- MicroTech II Units Compressor Dataplate Evaporator Dataplate Condenser Dataplate Front View RPL 7000000 / Page 4

Nomenclature Unit Dataplate Units w/ Free Standing Starter Model Number- Unit WSC 050 K Unit Model WSC= Water- Cooled Single Compressor Centrifugal Chiller HSC= Water- Cooled Single Compressor Centrifugal Chiller with Heat Recovery Condenser TSC= Templifier, Single Compressor Centrifugal Impeller type H, J, K, M (050 only) Impeller Size 048= 4.8" Diameter 050= 5.0" Diameter Style Number- Unit E 923456 010 6- Digit G.O. Number G.O. Item Number Serial Number- Unit STN U 01 05 048 Plant Identification Abbreviation STN = Staunton U= Unit Year of Manufacture 00= 2000 01= 2001 02= 2002 03= 2003 04= 2004 etc. Serial Number (build sequence) Month of Manufacture 01= January 07= July 02= February 08= August 03= March 09= September 04= April 10= October 05= May 11= November 06= June 12= December RPL 7000000 / Page 5

Nomenclature Model Number- Complete WSC 050K AE 10B YY Y B E1812 BE 2LA B4 0450 CC Y A C1612 BLYY Code: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 2LAYYY D4 1370 CCYY YY A A 134 082 FA MAEMBA 21YY2YYY 0191 H H2 B Code: 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 1 1 B Y R Y 1 A A 0155 U C C Y Y Y A 1 Code: 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 1. Model Type WSC= Water Cooled Centrifugal Chiller- Centrifugal HSC= Water Cooled Heat Recovery Chiller- Centrifugal TSC= Centrifugal Templifier 2. Compressor Size/Impeller Type 048 (4.8" impeller) 050 (5.0" impeller) 048H, 048J, 048K, 050H, 050J, 050K, 050M 3. Gear Ratio Code (speed code) ZT, ZU, ZV, ZW, Z2, ZY, ZZ, AA, AB, AC, AD, AE, AF, AG, AH, AJ, AK, AL 4. Motor Horsepower/Voltage first 2 digits= horsepower, third digit= voltage 10= 105HP 13= 135HP 15= 150HP 60 Hz. Codes N= 200V B= 208V P= 220V V= 230V W= 240V U= 380V 4= 400V A= 440V R= 460V S= 480V D= 575V M= 2400V C= 3300V L= 4160V 3= 2300V T= 4600V 2= 6600V Q= 13200V Z= 13800V 50 Hz. Codes E= 220V Y= 346V F= 380V G= 400V K= 415V H= 440V 7= 690V J= 3300V 6= 3000V 8= 6000V 9= 6600V 5= 10000V 1= 11000V 5. Refrigerant Contamination Protection YY= None 6. Sound Control Y= None W= Suction Shut Off Valve 7. Compressor Revision Level A= Rev. Level A B= Rev. Level B 8. Evaporator Description E1809= Standard Evaporator, 18" Diameter/9' Long E2009= Standard Evaporator, 20" Diameter/9' Long E2209= Standard Evaporator, 22" Diameter/9' Long E1812= Standard Evaporator, 18" Diameter/12' Long E2012= Standard Evaporator, 20" Diameter/12' Long E2212= Standard Evaporator, 22" Diameter/12' Long 9. Evaporator Tube Description first digit= Tube Count/ second digit= Tube type Tube Count 18" diameter: B= 86 C=76; 20" diameter: B= 116 C= 102; 22" diameter; B= 138 C= 122 Tube Type E= Turbo EFP.025 Wall; F= Turbo EFP.028 Wall; Q= Turbo EFP.035 Wall 10. Evaporator Head Description first digit= Number of Water Passes: 1, 2, 3 second digit= Inlet Nozzle Location: L= Left R= Right third digit= Nozzle Type: A= Grooved; B= Flanged; C= Marine Box- Grooved; E= Marine Box- Flanged 11. Evaporator Design Pressures first digit= Refrigerant Side Pressure: B= 180 PSIG; C= 200 PSIG; D= 225 PSIG second digit= Waterside Pressure: 1= 150 PSIG ASME; 2= 250 PSIG ASME; 3= 350 PSIG ASME; 4= 150 PSIG Non-ASME; 5= 300 PSIG Non-ASME; 8= 250 PSIG Non-ASME; 9= 300 PSIG ASME RPL 7000000 / Page 6

Nomenclature Model Number- Complete 12. Evaporator Leaving Water Temperature Code is listed in tenths of F (example 0450= 45.0 F) 13. Evaporator Tube Sheet & Head Material first digit= Tube Sheet Material: C= Carbon Steel; N= Monel Clad; S= Stainless Steel Clad; T= Titanium Clad Steel; E= Enecon (Ceramalloy) second digit= Head Material: C= Carbon Steel; E= Enecon (Ceramalloy); D= Devcon 14. Evaporator Tube Cleaning System Y= None B= WSA Brushes 15. Evaporator Model Revision A= Revision A 16. Condenser Description C1609= Standard Condenser, 16" Diameter/9' Long C1612= Standard Condenser, 16" Diameter/12' Long C1809= Standard Condenser, 18" Diameter/9' Long C1812= Standard Condenser, 18" Diameter/12' Long C2012= Standard Condenser, 20" Diameter/12' Long C2012= Standard Condenser, 20" Diameter/12' Long S1609= Split-Head Condenser, 16" Diameter/9' Long S1612= Split-Head Condenser, 16" Diameter/12' Long S1809= Split-Head Condenser, 18" Diameter/9' Long S1812= Split-Head Condenser, 18" Diameter/12' Long S2012= Split-Head Condenser, 20" Diameter/12' Long S2012= Split-Head Condenser, 20" Diameter/12' Long 17. Condenser Tube Description first digit= Tower Condenser Tube Count 16" diameter: B= 128 C=98; 18" diameter: B= 171 C= 137; 20" diameter: B= 248 C= 212 D= 192 second digit= Tower Condenser Tube Type L= Turbo CSL.025 Wall; N= Turbo CSL.028 Wall; P= Turbo CSL.035 Wall third & fourth digits= Heat Recovery (Split Head Condenser) Tube Count & Tube Type Contact Daikin Applied If there is no Heat Recovery Condenser, digits 3 & 4= YY 18. Tower Condenser Head Description/Heat Recovery (Split Head Condenser Only) Head Description first & fourth digit= Number of Water Passes: 1, 2, 3 second & fifth digit= Inlet Nozzle Location: L= Left R= Right third digit= Nozzle Type: A= Grooved; B= Flanged; D= Marine Box- Grooved; F= Marine Box- Flanged sixth digit= Nozzle Type: A= Grooved; B= Flanged If there is no Heat Recovery Condenser, digits 4, 5 & 6= YYY 19. Condenser Design Pressures first digit= Refrigerant Side Pressure: C= 200 PSIG; D= 225 PSIG; E= 250 PSIG; F= 275 PSIG; G= 300 PSIG second digit= Waterside Pressure: 1= 150 PSIG ASME; 2= 250 PSIG ASME; 3= 350 PSIG ASME; 4= 150 PSIG Non-ASME; 5= 300 PSIG None-ASME; 8= 250 PSIG Non-ASME; 9= 300 PSIG ASME 20. Maximum Condenser Leaving Water Temperature Code is listed in tenths of F (example 1370= 137.0 F) 21. Condenser Tube Sheet & Head Material first & third digit= Tube Sheet Material: C= Carbon Steel; N= Monel Clad; S= Stainless Steel Clad; T= Titanium Clad Steel; E= Enecon (Ceramalloy) second & fourth digit= Head Material: C= Carbon Steel; E= Enecon (Ceramalloy); D= Devcon If there is no Heat Recovery Condenser, digits 3 & 4= YY 22. Condenser Tube Cleaning System YY= None Tower Cond./None HR Cond. YB= None Tower Cond./WSA Brushes HR Cond. BY= WSA Brushes Tower/None HR Cond. BB= WSA Brushes Tower/WSA Brushes HR Cond. 23. Condenser Model Revision A= Revision A ; B= Revision B; C= Revision C RPL 7000000 / Page 7

Nomenclature Model Number- Complete 24. Pressure Vessel Code A= ASME; J= Australian; S= Swiss; P= Chinese; K= Korean; 0= CRN British Columbia 7= CRN Nova Scotia 1= CRN Alberta 8= CRN Prince Edward Island 2= CRN Saskatchewan 9= CRN Newfoundland 3= CRN Manitoba F= CRN Nunavut 4= CRN Ontario W= CRN Northwest Territories 5= CRN Quebec U= CRN Yukon 6= CRN New Brunswick 25. Refrigerant Type 134=Refrigerant 134a 26. Refrigerant Weight Total weight divided by 10 rounded to next whole number (example: 815/10= 082) 27. Main Expansion Valve/ Pilot Valve first digit= Main Expanion Valve: F= 125 ton TXV; G= 150 ton TXV; H= 180 ton TXV; I= 250 ton TXV B= 150 ton EEXV; C= 250 ton EEXV second digit= Pilot Valve: A= 4 ton (TXV); Y=None 28. Controller Options MicroTech 200 first digit= Control Type: M= MicroTech second digit= Sensor Functions: A= Outdoor Air (OA) Thermistor S20; B= OA and HR; H= Heat Recovery(HR) Thermistors S21/S22 third digit= Language: E= English Language/English Units; M= English Language/Metric Units; J= Japanese; C= Chinese fourth digit= Instruments: M= Modem; Y= None fifth digit= Special Functions: A= Analog Outputs; B= Analog Outputs & Signal Converter; S= Signal Converter sixth digit= Enclosure: A= NEMA 1; B= NEMA 4; C= NEMA 12 MicroTech II first digit= Control Type: 2= MicroTech II second digit= Size: L= Large; S= Small; H= Heat Recovery third digit= Language: E= English Language fourth digit= Instruments: M= Modem; Y= None fifth digit= Communications: B= BACnet MS/TP; E= BACnet IP; L= Lonmark; M= MODBUS; P= Serial Port w/modem; S= Serial Port (RS232); Y= None sixth digit= Enclosure: A= NEMA 1; B= NEMA 4/ NEMA 12 29. Starter Options first digit= Starter Type: 2= Wye-Delta Closed; 3= Across-The-Line; 4= Auto Transformer; 5= Primary Reactor; 6= Solid State V= Variable Frequency Drive; Y= None second digit= Enclosure: 1= 72" Unit Mounted; 5= 90" X 36" X 21" Free Standing; 7= Med/Hi Voltage 90 X 36 X 30 Free Standing; 9= Med/High Voltage 90" X 72" X 30" Free Standing; E= Mini Cabinet Unit Mounted; L= VFD Free Standing; M= VFD Unit Mounted; R= 72" Terminal Mounted; Y= None third digit= VFD Cooling Mode: A= Air Cooled; P= Power Flex 755 Air Cooled; W= Water Cooled; Y= None fourth digit= Y fifth digit= Surge Protection Capacitor: 2= Surge Capacitor mounted in Compressor Motor Terminal Box; S= Surge Capacitor mounted in Starter Box; Y= None sixth digit= Y seventh digit= Ground Fault Protection: Y= None; G= Ground Fault Protection Module eighth digit= Meters: A= Ammeter Module; F= Full Metering Module; Y= None 30. Rated Load Amps Actual RLA 31. Hot Gas Bypass H= Hot Gas Bypass Y= None RPL 7000000 / Page 8

Nomenclature Model Number- Complete 32. Insulation first digit= Condenser & Evaporator Shell Insulation: H= 3/4 Closed Cell Foam Insulation on Evaporator Shell, Suction Piping, Compressor Inlet, MotorBarrel + High Humidity 2= 3/4" Closed Cell Foam Insulation on Condenser Shell Only 3= 1-1/2 Closed Cell Foam Insulation on Evap. Shell, 3/4 Insulation on Suction Piping, Comp. Inlet, MotorBarrel + High Humidity 5= Code H + Code 2 6= Sound Insulation on Condenser & Discharge Line 7= Sound Insulation on Discharge Line Only 8= Code H + Code 2 + Oil Pump 9= Code 3 + Code 2 + Oil Pump M= Code H + Code 7; N= Code 3 + Code 7 S= Code H + Code 6; T= Code 3 + Code 6 Y= None second digit= Condenser & Evaporator Head Insulation: Y= None; 1= Return Heads Only; 2= Evaporator Return & Connection Heads; 3= Condenser Return & Connection Heads; 4= Evaporator Return, Condenser Return & Connection Heads 33. Water Pressure Differential Switch E= Evaporator C= Condenser B= Both Evaporator & Condenser Y= None 34. Paint 1= Standard Painting; Y= None 35. Packaging 1= Standard Wood Skid; 2= Open Export Crate; 3= Totally Enclosed Export Crate; 4= Shipping Bag w/wood Skid 5= Shipping Bag Only; 6= Shipping Bag w/ Totally Enclosed Export Crate; 7= Shipping Bag w/open Export Crate; Y= None 36. Refrigerant Tag A= Full Factory Charge B= Holding Charge 37. Miscellaneous Y= None X= Special (specials are not covered in the normal code string) 38. Oil Cooler R= Refrigerant Cooled; S= Water Cooled w/factory Solenoid; Y= None 39. Knockdown Y= None 1= Type 1- Compressor and Standard Stack, Run Test, No Refrigerant 2= Type 2- Compressor and Bolted Stack, No Test, No Refrigerant 3= Type 3- Bolted Stack, Run Test, With Refrigerant 40. Testing 1= Standard Factory Performance Test 2, 9, A, B, C, D, E, F, G, H, J, Q, S= Various Witness Tests 3, 4, 5, 6, 7, 8, K, L, M, N, P, R, T= Various Certified Performance Tests Y= None 41. Approval Listing A= AHRI Approval U= UL C= Canadian UL V= AHRI + UL D= Canadian AHRI + UL Y= None B= AHRI + ETL + CETL O= AHRI + ETL + CETL + OSP-IBC E= ETL + CETL P= ETL + CETL + OSP-IBC N= AHRI + OSP-IBC Q= OSP-IBC 42. Latest Unit Model Revision A= Revision A 43. Tons Actual Tons RPL 7000000 / Page 9

Nomenclature Model Number- Complete 44. Startup Y= Export- No Startup U= Domestic Startup 7= Canadian Startup 45. Labor Warranty C= Entire Unit Parts & Compressor-only Labor P= Entire Unit Parts Only Y= Entire Unit Parts and Labor 46. Extended Warranties 1= Year 2- Entire Unit parts + Labor; Years 3 thru 5- Compressor parts + Labor 2= Year 2- Entire Unit parts + Labor; Years 3 thru 5- Compressor parts only 3= Year 2- Entire Unit parts only; Years 3 thru 5- Compressor parts only Y= None These Codes apply to Entire Unit Including Starter: C= Extended 1 year parts; D= Extended 1 year parts + Labor; E= Extended 2 year parts; F= Extended 2 year parts + Labor; G= Extended 3 year parts; H= Extended 3 year parts + Labor; J= Extended 4 year parts; K= Extended 4 year parts + Labor; 4= Extended 5 year parts; 5= Extended 5 year parts + Labor; 6= Extended 9 year parts; 7= Extended 9 year parts + Labor These Codes apply to Compressor/Drive Train Only: L= Extended 1 year parts; M= Extended 1 year parts + Labor; N= Extended 2 year parts; O= Extended 2 year parts + Labor; P= Extended 3 year parts; Q= Extended 3 year parts + Labor; R= Extended 4 year parts; S= Extended 4 year parts + Labor; T= Extended 5 year parts; U= Extended 5 year parts + Labor; V= Extended 9 year parts; W= Extended 9 year parts + Labor 47. Y= None 48. Y= None 49. Y= None 50. Motor Vendor A= A.O. Smith C= YYZ M= Ram R= Reliance 51. Refrigerant Warranty 0 thru 5= Actual number of years RPL 7000000 / Page 10

Electrical Legend Sch. Sym. Description Location 1M, 2M Contactor Starter 1S, 2S Energizing Contactor Starter ADI Analog/Digital Input Board MicroTech 200 Control Box AOX Analog Output Board MicroTech 200 Control Box CAP Capacitor Lube Box (MicroTech 200) or Compressor Control Box (MicroTech II) CB Circuit Breaker MicroTech 200 or MicroTech II Unit Control Box CF Condenser Flow Switch Tube Sheet Support- MicroTech II Units CHW1 Evaporator Flow Switch Tube Sheet Support- MicroTech 200 Units CR Relay MicroTech II Compressor Control Box CS01- CS10 Sensors- Compressor Controller Throughout Unit- MicroTech II (see MicroTech II section for sensor placement) CTB1, CTB2 Terminal Block Compressor Controller- MicroTech II Units CW1 Condenser Flow Switch Tube Sheet Support- MicroTech 200 Units DIST/ISO Dist. & Isolation Board MicroTech II Unit Controller EF Evaporator Flow Switch Tube Sheet Support- MicroTech II Units FVC Flux Vector Control VFD Panel (Code 29-1= V) HP High Pressure Switch MicroTech 200 Panel HR Relay MicroTech II Compressor Controller KDI Keypad/Display MicroTech 200 Panel LR Relay MicroTech II Compressor Controller MCB1 Main Control Board MicroTech 200 Panel MCR Motor Control Relay Starter Panel OBA Output Board MicroTech 200 Panel OIM Operator Interface Module VFD Panel (Code 29-1= V) OITS Operator Interface Touch Screen MicroTech II Units OL Oil Pump Overload Lube Box (MicroTech 200) or Compressor Control Panel (MicroTech II) OP Oil Pump Contactor Lube Box (MicroTech 200) or Compressor Control Panel (MicroTech II) pc02 Main Controller MicroTech II Unit Controller PHP1 High Pressure Transducer Discharge Nozzle plan LAN Cable Connects MicroTech II Controllers RES Transition Resistor Starter RMI Remote Meter Interface VFD (Code 29-1= V) S00- S22 Sensor- MicroTech 200 Throughout the Unit (see MicroTech 200 section for sensor placement) SA/SB 4- Way Vane Speed Solenoid Lube Box (MicroTech 200 Units) or (Needle Valves) Compressor Gear Housing (MicroTech II Units) SC Signal Converter MicroTech 200 Control Box or MicroTech II Compressor Control Box T1, T2, T3 Main Control Transformer Starter T2 24V Control Transformer MicroTech 200 Control Box T3 18V Control Transformer MicroTech 200 Control Box TB1, TB2 Terminal Block Junction Box used w/field supplied starter TR Timing Relay Starter TRP Transition Resistance Protector Starter TSW Toggle Switch- Templifier MicroTech 200 Control Box (TSC only) US02- US10 Sensor- Unit Controller Throughout Unit- MicroTech II (see MicroTech II section for sensor placement) UTB1 Unit Control Terminal Block MicroTech II Unit Control Box VC Vane Close Switch Lube Box- MicroTech 200 Unit VR Voltage Relay Lube Box- MicroTech 200 Unit or MicroTech II Compressor Control Box RPL 7000000 / Page 11

Control Box- MicroTech 200 Mounting of Unit Control Panel and Lube Box 37 36 35 201 201 11 36 37 35 303 38 37A 35A 303 304 741 742 743 744 Ref. Description Part Qty. No. Number 11 Accessory Shelf 1 070013205 1 35 Screw- w/shelf 735033230 10 35A Screw- no shelf 000086100 4 36 Washer, Plain- w/shelf 040500316 10 37 Washer, Lock- w/shelf 048164812 10 37A Washer, Lock- no shelf 048164812 4 38 Nut- no shelf 040499906 4 201 Control Box- MicroTech 200 2 303 Bracket- Control Box Mounting 18" dia. evap. 070013211 3 20" dia. evap. 070013212 3 22" dia. evap. 070013213 3 304 Bracket- Lube Box Mounting 330110202 3 741 Lube Box Assy 2 074124301 1 742 Screw- Hex Head 000164500 4 743 Nut- Hex 040499901 4 744 Washer- Lock 048164808 4 1 Accessory shelf is used for mounting the junction box used when a unit was ordered with a field installed starter (code 29 second digit= 5, 7, 9, A). 2 See following pages for component detail. 3 Qty. is 4 for units with field installed starters (with shelf), and 2 for units with factory installed starters (no shelf). RPL 7000000 / Page 12

Control Box- MicroTech 200 Front Panel & Inside of Micro Control Door Assembly 506 503 503 505 Inside of Micro Door Ass'y 418 414 504 413 418 412 418 Ref. Description Part Qty. No. Number 412 Toggle Switch- Contrast Control 735004521 1 413 Membrane Switch- Control English Language 057900901 1 Japanese Language 057900911 1 Chinese Language 074789101 1 414 KDI Control 073378501 1 418 Cover- KDI Board 073012201 1 503 Hinge- Painted 070806401 2 504 Latch- Door Lock 350065401 1 505 Door- Power 073117201 1 506 Door- Control 350108101 1 N/S Cover- Sensor 070691601 1 N/S= Not Shown on diagram. RPL 7000000 / Page 13

Control Box- MicroTech 200 Interior Panel Modem Detail 971 972 974 159 163 152 160 511 154 161 162 184 183 182 976 970 524 525 104 103 102 158 109 126 125 106 523 108 157 126 125 113 507 508 509 107 518 522 Micro Door Ass'y (see previous page) 142 130 156 150 155 143 111 RPL 7000000 / Page 14

Control Box- MicroTech 200 Interior Panel Ref. Description Specification Part Qty. No. Number 102 Main Controller- MicroTech M280 065487350 1 1 103 ADI Board until 3/03 065816003 1 ADI Board 3/03 and later 330325401 1 104 Mount- ADI Board 055727206 1 106 Cord Set- PCB Interface 049265103 1 107 Ribbon Cable 50C 18/24 OB 049265208 1 108 Ribbon Cable 50C 3" 072941801 2 109 Clip, Flat- Cable 049766201 2 111 Terminal Block AD1 AD2 072993901 2 113 Transformer- Control.03 KVA 24/18V 046738114 1 125 Terminal Block 9 Pole 1 Row 065499909 11 126 Cover- Terminal Block 065500009 11 130 Bracket- Terminal Block 073212801 3 142 Board- Signal Converter SC 049264901 1 143 Spacer- Signal Converter 048166702 4 150 Toggle Switch (TSC Templifier Only) TSW 735004521 1 152 Output Board 24 SM 072986401 1 154 Board- Guardistor 067113001 1 155 Circuit Breaker 3A 1P 735073301 1 156 Transformer 50 VA 120/24V 060630801 1 157 Terminal Block Unit & Field 073118801 1 158 Varistor 30 VRMS 049759701 1 159 Ferrules- Dual Wires 8 mm 073008204 19 160 Mount- Circuit Board 055727207 1 161 Socket, Relay- High Pressure 735003105 1 162 Relay- High Pressure HP 735020820 1 163 Relay- Output Board 073202501 19 182 AOX Board 4 Channel 066794804 1 183 Mount- AOX Board 055727203 1 184 Cord Set 9" 28AWG 065499702 1 507 Bracket- Magnetic Latch 073212701 1 508 Magnetic Latch 034905200 1 509 Fastener- Magnetic Latch 034905000 1 511 Gasket.12 X.75 070199209 1 518 Bushing- Snap In 2.00" 030188500 1 522 Bushing- Snap In 1.50" 036561900 1 523 Plug- Terminal Housing 4 Pin Female 049264502 1 524 Plug- Terminal Housing 6 Pin Female 049264501 2 525 Terminal- Socket 24-18 AWG 049264702 12 970 Modem 14.4 BAUD 063585005 1 971 Cord Set- Modem 073372702 1 972 Gasket.25 X.70 070199207 1 974 Bracket- Modem Mounting 073043505 1 976 Bracket- Vertical, Modem 073014701 1 1 Controller needs to be programmed. The Unit serial number is required to properly program the controller. RPL 7000000 / Page 15

Control Box- MicroTech 200 Sensors S20 S16 S02 S15 S18 S13 S00 S14 S17 S01 S10 S12 S22 S18 S21 S09 S08 Ref. Description Part Qty. No. Number S00 Sensor- Evaporator Leaving Water Temp. 073012002 1 S01 Sensor- Evaporator Entering Water Temp. 073012002 1 S02 Sensor- Compressor Suction Temp. 073012002 1 S08 Sensor- Condenser Liquid Line Temp. 073012002 1 S09 Sensor- Condenser Entering Water Temp. 073012002 1 S10 Sensor- Condenser Leaving Water Temp. 073012002 1 S12 Sensor- Compressor Discharge Temp. 073012002 1 S13 Sensor- Oil Feed Temp. 073012002 1 S14 Sensor- Oil Sump Temp. 073012002 1 S15 Oil Vent Low Pressure Transducer 071568501 1 S16 Evap. Refrigerant Low Press. Transducer 071568501 1 S17 Cond. Refrigerant High Press. Transducer 071568601 1 S18 Oil Feed Gauge High Press. Transducer 071568601 1 S20 Outdoor Air Sensor- 50 ft. 073012005 1 S21 Entering Heat Recovery Temp. Sensor 073012002 1 S22 Leaving Heat Recovery Temp. Sensor 073012002 1 N/S Boot- Transducer Protection 071583301 4 N/S Cable- Pressure Transducer, 10 ft. 074667501 3 N/S Cable- Pressure Transducer, 15 ft. 074667502 1 N/S High Pressure Switch- 190 PSI 074796302 1 N/S= Not Shown on diagram. RPL 7000000 / Page 16

Control Box- MicroTech 200 Compressor Lube Box Assembly 1 28 28A 53 19 20 17 5 9 18 8 26 34 31 21 27 14 15 2 7 16 RPL 7000000 / Page 17

Control Box- MicroTech 200 Compressor Lube Box Assembly Ref. Sch. Description Part Qty. No. Sym. Number Lube Box Assembly- Complete 074124301 1 Box 074124201 1 2 Cover 744417501 1 5 VC Switch- Vane Close 070180512 1 7 Washer 735043444 5 8 SA SB 4 Way Solenoid Valve 735048465 1 9 Connector.25"F X.44"T 735043925 4 14 Coupling.25"F 047139601 1 15 Tee.25"F X.25"F X.25"F 735034401 1 16 Union- Brass.25"F 735044201 5 17 Mounting Channel 775115202 1 18 Clamp- Terminal Block 735073104 2 19 Terminal Block End 735073102 1 20 Terminal Block Section 735073101 16 21 Strap- Capacitor 775107001 1 26 VR Relay- Voltage 18A 735020118 1 27 CAP Capacitor 161 MFD 250V 735002714 1 28 OL Overload until 5/02 735009309 1 OL Overload 5/02 & later 735021501 1 28A Heater- Overload 5/02 & later only 735021578 1 31 Contactor- Oil Pump 4P 2NO/2NC 21A 072997401 1 34 Fitting.50" 735047908 1 53 Jumper- Terminal Block 735073105 1 RPL 7000000 / Page 18

Control Box- MicroTech II Unit Control Box Mounting 18 27 23 21 22 24 22 24 19 25 22 23 26 15 16 18 19 NOTE: Original design Operator Interface Panel shown. Mounting hardware is the same for all panels. Ref. Description Specification Part Qty. No. Number 15 Operator Interface Panel (OITS), Original until 5/05* 071858001 1 Cable, 7-wire single, Original until 5/05* 330367901 1 Connector Only, Original until 5/05* 330332007 1 15 Operator Interface Panel w/cables, 12 Beige 5/05 & later* 330277501 1 15 Operator Interface Panel w/vga & Serial cables, 15 Beige 5/05 & later* 330276501 1 15 Operator Interface Panel w/ VGA & Serial cables, 15 Black 5/05 & later* 330276502 1 Cable, 12V DC Power w/4 Pin Molex & 2 Plugs all 5/05 & later* 300040768 1 Cable, Serial all 5/05 & later* 300043345 1 Cable Kit (includes VGA & Serial cables) all 5/05 & later* 300043289 1 Power Cord w/ac Adapter all 5/05 & later* 300053912 1 16 Support Arm Assy, Beige (includes swivel pin, washers, & nut) 330815401 1 16 Support Arm Assy, Black (includes swivel pin, washers, & nut) 330815411 1 18 Block- Mount 330406501 2 19 Shelf 330329601 1 21 Screw 040499041 4 22 Washer- Plain 040500316 12 23 Washer- Lock Spring 048164812 8 24 Washer- Lock 040500213 12 25 Washer- Nylon 330366101 4 26 Nut 040499906 4 27 Screw 040499040 4 * For units built 1/05 to 5/05, check unit to verify which panel is installed. Original panel had single cable, later panels have 3 cables. RPL 7000000 / Page 19

Control Box- MicroTech II Compressor Control Box Mounting 280 282 Compressor Control Box 261 282 283 284 285 281 294 295 290 292 293 304 Condenser Ref. Description Specification Part Qty. No. Number 261 Plate- Mounting 330366501 1 280 Screw 040499039 4 281 Washer- Nylon 330366101 4 282 Washer- Lock External Tooth 040500212 2 283 Washer- Plain 040500308 4 284 Washer- Lock 048164812 4 285 Nut 040499905 4 290 Screw 040499033 4 292 Washer- Lock External Tooth 040500210 2 293 Washer- Plain 040500307 4 294 Washer- Lock Spring 048164810 4 295 Nut 040499904 4 304 Bracket 330110202 2 RPL 7000000 / Page 20

Control Box- MicroTech II Unit Control Box Detail-Until 5/05 102 154 153 152 106 105 104 151 153 103 101 107 Electronic Expansion Valve Driver & Transformer Detail (Code 27= AY, BY or CY) Modem Detail (Code 28= 2LEYPA) 3 2 16 4 10 6 5 Unit Control Detail 1 7 8 RPL 7000000 / Page 21

Control Box- MicroTech II Unit Control Box Detail - Until 5/05* Ref. Sch. Description Specification Part Qty. No. Sym. Number 1 Enclosure- No Emergency Cut-Off Switch until 2/03 330406101 1 Enclosure- w/emergency Cut-Off Switch 2/03 & later 330406102 1 2 Bracket- Switches 330329701 1 3 UTB1 Terminal Block w/rail 330407301 1 4 pc02 Controller- with Display 1 Large 330268311 1 pc02 Controller- with Display 1 Small 330268111 1 5 CB Circuit Breaker 5 Amp SP 735073302 1 6 Switch 125V 071995301 2 7 Serial Gateway RS 232 Code 28, digit 5= P,S 330343102 1 MODBUS Code 28, digit 5= M 330343101 1 LonWorks Code 28, digit 5= L 330343401 1 BACnet MS/TP Code 28, digit 5= B 350147407 1 BACnet w/ethernet Code 28, digit 5= E 350147406 1 8 Board- Distribution & Isolation with connectors 330272602 1 10 Connector Large Controller 330803053 1 Connector Small Controller 330803051 1 16 Switch- Emergency Cut-Off 735004521 1 101 Bracket- Modem Code 28= 2LEYPA 330421601 1 102 Bracket- Modem Code 28= 2LEYPA 330421601 1 103 Circuit Board- Modem Code 28= 2LEYPA 330274501 1 104 Bracket Code 28= 2LEYPA 070199207 1 105 Cord Set- Modem Code 28= 2LEYPA 330422001 1 106 Cord Set- BACnet Code 28= 2LEYPA 330421901 1 107 Serial Gateway- RS232 Code 28= 2LEYPA 330343102 1 N/S Connector- Service 330406701 1 151 Bracket- Driver 330277701 1 152 Transformer located behind bracket 330277601 1 153 Screw #6-.37 735032716 2 154 Driver 330277803 1 N/S= Not Shown on diagram. 1 Controller must be programmed before shipping. Unit serial number and software code (located on controller label) are required when ordering to insure proper software installation. Large controllers are standard, there are a few small controllers in the field (see code 28). *This control box was used with the original operator interface panel (which is connected to the control box with one seven-wire cable). A new design flatscreen operator interface panel can be retrofitted for use with this control box using retrofit kit p/n 300040547. RPL 7000000 / Page 22

Control Box- MicroTech II Unit Control Box Detail- 5/05 and Later 25 24 23 Liquid Line Electronic Expansion Valve Driver & Transformer Detail 2 3 16 10 4 22 5 6 17 8 12 7 RPL 7000000 / Page 23

Control Box- MicroTech II Unit Control Box Detail- 5/05 and Later Ref. Sch. Description Specification Part Qty. No. Sym. Number 2 Bracket- Switches 330329701 1 3 UTB1 Terminal Block w/rail 330407301 1 4 pc02 Controller- with Display 1 330268311 1 5 CB Circuit Breaker 5 Amp SP 735073302 1 6 Switch 125V 071995301 2 7 Serial Gateway RS 232 Code 28, digit 5= P,S 330343102 1 MODBUS Code 28, digit 5= M 330343101 1 LonWorks Code 28, digit 5= L 330343401 1 BACnet MS/TP Code 28, digit 5= B 350147407 1 BACnet w/ethernet Code 28, digit 5= E 350147406 1 8 Relay 24V 330720910 1 10 Connector 330803053 1 12 Holder- Relay 330720911 1 16 Switch- Emergency Cut-Off 735004521 1 17 UCM Board- Universal Communications 330275202 22 PC Assy- Single Board PC 330277301 1 23 Driver- Liquid Line Electronic Expansion Valve 330277803 1 24 Transformer- Isolation 15VA 330277601 1 25 Bracket- EXV Board 330277701 1 N/S Connector- Service 330406701 1 N/S= Not Shown on diagram. 1 Controller must be programmed before shipping. Unit serial number and software code (located on controller label) are required when ordering to insure proper software installation. RPL 7000000 / Page 24

Control Box- MicroTech II Compressor Control Box Detail 9 11 12 10 28 32 5 4 3 7 27 18 1 31 6 17 22 15 16 2 30 21 RPL 7000000 / Page 25

Control Box- MicroTech II Compressor Control Box Detail Ref. Sch. Description Specification Part Qty. No. Sym. Number 1 pc02 Controller 1 330268311 1 2 T2/T3/T4 Transformer 120V- 24V 100VA 9/04 & later 330720902 3 until 9/04 330278102 3 3 OP Contactor- Oil Pump 4P 21A 24VAC Coil 330278203 1 4 OL Overload- Oil Pump 48DA18AA4 735021501 1 5 VR Relay- Voltage 18A 735020118 1 6 CTB1 Terminal Block w/rail 330406202 1 7 CAP Capacitor- 60 Hz. Units 161 MFD 250V 330261502 1 CAP Capacitor- 50 Hz. Units 189 MFD 250V 330261501 1 9 CB Circuit Breaker 6A 330278109 1 9/04 & later 330720909 1 until 9/04 330278109 1 10 LR/CR/HR Relay 24VAC 10A 9/04 & later 330720910 3 until 9/04 330278110 3 11 Mounting Rail- Relays 9/04 & later 330720911 3 Mounting Rail- Relays until 9/04 330278111 3 12 Springs- Relay Hold Down 330278112 3 15 Standoff- Nylon Post 330406301 10 16 SC Signal Converter Board 049264901 1 17 Guardistor Board 330343901 1 18 CTB2 Terminal Block 330406203 1 21 Board- 3 Transducer 071857701 1 22 Cover 9/04 & later 330720922 1 Cover until 9/04 330278122 1 27 Bushing 001242600 2 28 Heater- Overload 735021578 1 30 Connector Kit- Transducer 330803054 1 31 Connector Kit- Controller 330803053 1 32 Barrier 330406601 1 1 Controller must be programmed before shipping. Unit serial number and software code (located on controller label) are required when ordering to insure proper software installation. RPL 7000000 / Page 26

Control Box- MicroTech II 4- Way SA/SB Solenoid Valve & Tubing Until 7/05 753 746 747 751 754 755 765 Port 'A' 765 754 755 748 752 761 765 763 759 754 Inlet Port 'P' 755 747 755 748 749 750 755 754 Exhaust Port 'E' 754 Port 'B' Ref. Description Specification Part Qty** No. Number 746 Connector.25" Flare x.44" Thread 735043930 1 747 Fitting- Straight Thread 070789304 2 748 Fitting- Straight Thread 070789306 2 749 Fitting- Straight Thread 070789303 2 750 Valve- Solenoid SA/SB 4- Way Vane Control 073221501 1 751 Switch- Vane Close 071896001 1 752 Bracket- SA/SB Valve Mounting 330366301 1 753 Coupling.25" Flare 047139601 1 754 Fitting- Nut 070789309 6 755 Fitting- Sleeve 070789315 6 759 Tee.25" ODS 041117803 1 761 Screw 735033204 2 763 Distributor.25" x.25" 047350301 1 765 Flare Nut 000028600 7 N/S MicroTech Pressure Connector 1 070811203 1 N/S= Not Shown on above diagram. **Quantities listed are for ONE compressor. Each compressor has identical components. 1 Connects to control box oil gauge transducer. Detail shown below. 783 781 Ref # Description Part No. Qty. 781 Tee 041117803 1 783 Schrader Valve 071100801 1 RPL 7000000 / Page 27

Control Box- MicroTech II 4- Way SA/SB Solenoid Valve & Tubing 7/05 and Later 747 751 746 765 765 765 761 754 752 755 765 765 763 759 765 754 748 755 Port 'A' 754 748 750 Inlet 755 Port 'P' Exhaust Port 'E' 748 748 755 754 755 754 Port 'B' Ref. Description Specification Part Qty** No. Number 746 Connector.25" Flare x.44" Thread 070789336 1 747 Fitting- Straight Thread 070789304 1 748 Fitting- Straight Thread 070789306 4 750 Valve- Solenoid SA/SB 4- Way Vane Control 073221501 1 751 Switch- Vane Close 071896001 1 752 Bracket- SA/SB Valve Mounting 330366301 1 754 Fitting- Nut 070789309 5 755 Fitting- Sleeve 070789315 5 759 Tee.25" ODS 041117803 1 761 Screw 735033204 2 763 Distributor.25" x.25" 047350301 2 765 Flare Nut 000028600 7 N/S MicroTech Pressure Connector 1 070811203 1 N/S= Not Shown on above diagram. **Quantities listed are for ONE compressor. Each compressor has identical components. 1 Connects to control box oil gauge transducer. Detail shown below. 783 781 Ref # Description Part No. Qty. 781 Tee 041117803 1 783 Schrader Valve 071100801 1 RPL 7000000 / Page 28

403 Control Box- MicroTech II 402 Cables and Sensors 426 17 559 995 998 411 552 551 552 557 750 406 552 552 557 HSC Only Unit Sensor Location and Details 551 80 100 553 60 552 220 750 553 552 557 748 220 60 552 557 750 Liquid Line Tubing 553 100 Liquid Line Tubing 552 748 559 60 60 552 553 558 557 RPL 7000000 / Page 29

Control Box- MicroTech II Cables and Sensors Ref. Sch. Description Specification Part Qty. No. Sym. Number 17 Cable- Operator Interface Panel until 5/05 330367901 5 1 Connector Only 330332007 1 60 Conduit Fitting.375" 735048013 7 80 Conduit Fitting.250" 735048015 1 100 Valve Core 026541100 2 220 Sensor Well until 9/02 070809003 4 1 Sensor Well 9/02 and later 047441511 1 402 Cable, Empty- Comp Heater 1 330006706 1 403 Cable- Oil Pump Heater 1 330006744 1 406 Cable- Solenoids 330287403 2 411 Cable- Differential Pressure Switches 074608901 ** 426 Cable- Starter 2 Units with Factory Mounted Purchased Starter 070829981 1 Units with Field Installed Purchased Starter 070829982 1 551 CS05 Sensor 073007302 1 552 3 Sensor 073007202 *** 553 Boot- Transducer 071583301 4 557 Cable- Transducer 074667502 4 558 HP1 Switch- High Pressure until 6/03 074796302 1 HP1 Switch- High Pressure 6/03 & later 074796301 1 559 Cable- High Pressure Switch 1 070829997 1 748 CS02/06 Transducer- High 410 PSI 071568601 2 750 CS01/03 Transducer- Low 132 PSI 071568501 2 995 plan Cable- plan between Unit & Compressor Controllers 034248800 **** 998 Cable- Power between Unit & Compressor Controllers 330406402 15 ft. ** There is one cable per DPS (see code 33). Each cable is 16 ft. of the above referenced p/n. *** Quantity is 8 on WSC/TSC units, 10 on HSC units. **** There are two cables. Each made from 15 feet of the above listed p/n. 1 Cables contain 90 fitting p/n 000916900 and Anti- Short bushing p/n 047356401. 2 See Starter section for all starter- related cables and mounting components. 3 CS04, CS07, CS09, CS10, US02, US 03, US04, US05 [ US09 & US10 on HSC units only]. 4 Paste for sensor well is p/n 735026315. 5 This cable was used with the original operator interface panel. The new flat screen panel uses a VGA cable and a serial cable which come with the panel. Unit Control Sensor Application Sensor Application US02 Evaporator Entering Water Temp. US03 Condenser Entering Water Temp. US04 Condenser Leaving Water Temp. US05 Liquid Line Temp. US09 Heat Recovery Entering Water Temp. US10 Heat Recovery Leaving Water Temp. Compressor Control Sensor Application Sensor Application CS01 Oil Sump Pressure CS02 Oil Feed Gauge Pressure CS03 Evap. Refrigerant Pressure CS04 Oil Sump Temperature CS05 Compressor Suction Temp. CS06 Cond. Refrigerant Pressure CS07 Compressor Discharge Temp. CS08 % Compressor Amps (Starter) CS09 Oil Feed Temperature CS10 Evap. Leaving Water Temp. RPL 7000000 / Page 30

Starter- Factory Installed Units with MicroTech 200 Control Box Cables, Mounting 317 450 449 436 448 438 443 445 447 Ref. Description Specification Part Qty. No. Number 317 Bracket- Starter Mounting 350257302 4 436 Cable To Compressor Control Box 070829979 1 438 Cable 1 To Compressor 144 RLA Max. Motors All Compressor Terminals 331007701 1 177 RLA Max. Motors All Compressor Terminals 331007702 1 206 RLA Max. Motors All Compressor Terminals 331007703 1 238 RLA Max. Motors All Compressor Terminals 331007704 1 278 RLA Max. Motors All Compressor Terminals 331007705 1 298 RLA Max. Motors Compressor Terminals 1-3 331007706 1 298 RLA Max. Motors Compressor Terminals 4-6 331007707 1 348 RLA Max. Motors Compressor Terminals 1-3 331007708 1 348 RLA Max. Motors Compressor Terminals 4-6 331007709 1 399 RLA Max. Motors Compressor Terminals 1-3 331007710 1 399 RLA Max. Motors Compressor Terminals 4-6 331007711 1 460 RLA Max. Motors Compressor Terminals 1-3 331007712 1 460 RLA Max. Motors Compressor Terminals 4-6 331007713 1 443 Nut.50-13 735029505 16 445 Screw.50 x 1.2 735033246 16 447 Washer- Lock.50 Nom. 048164814 16 448 Angle Bracket 330107901 4 449 Cover- Terminal Box 070409501 1 450 Screw 190-16 x.5 038990703 4 1 Motor RLA is indicated on the compressor data plate. RPL 7000000 / Page 31

Starter, Compact - Factory Installed Units with MicroTech II Control Box Cables, Mounting 317 115 116 438 Starter 426 Compressor Control Box 43 Evaporator Bracket 41 42 20 41 50 40 20 40 41 50 Starter Cabinet 42 43 41 Ref. Description Specification Part Qty. No. Number 20 Angle Bracket 330107901 4 40 Screw.50 X 1.5 735033847 16 41 Washer- Plain.50 ZPS 040500311 32 42 Washer- Lock.50 ZPS 048164814 16 43 Nut.50-13 735029505 16 50 Washer- Lock Grounding 040500213 32 115 Cover- Terminal Box 070409501 1 116 Screw.19-24 X.50 046093802 4 426 Cable To Comp. Control Box 070829981 1 317 Bracket- Starter Mounting 350257302 4 438 Cable 1 To Compressor 144 RLA Max. Motors All Compressor Terminals 331007721 1 177 RLA Max. Motors All Compressor Terminals 331007702 1 206 RLA Max. Motors All Compressor Terminals 331007703 1 238 RLA Max. Motors All Compressor Terminals 331007704 1 278 RLA Max. Motors All Compressor Terminals 331007705 1 298 RLA Max. Motors Compressor Terminals 1-3 331007706 1 298 RLA Max. Motors Compressor Terminals 4-6 331007707 1 348 RLA Max. Motors Compressor Terminals 1-3 331007708 1 348 RLA Max. Motors Compressor Terminals 4-6 331007709 1 399 RLA Max. Motors Compressor Terminals 1-3 331007710 1 399 RLA Max. Motors Compressor Terminals 4-6 331007711 1 460 RLA Max. Motors Compressor Terminals 1-3 331007712 1 460 RLA Max. Motors Compressor Terminals 4-6 331007713 1 1 Motor RLA is indicated on the compressor data plate. RPL 7000000 / Page 32

Starter, Mini Cabinet- Factory Installed Units with MicroTech II Control Box Cables, Mounting 51 426 317 Starter Compressor Control Box 20 Starter Cabinet 48 Evaporator Bracket 43 41 41 50 40 20 46 47 52 46 47 Ref. Description Specification Part Qty. No. Number 20 Angle Bracket 330107901 4 40 Screw.50 X 1.5 735033847 8 41 Washer- Plain.50 ZPS 040500311 16 42 Washer- Lock.50 ZPS 048164814 8 43 Nut.50-13 735029505 8 46 Screw 735033233 8 47 Washer 040500316 16 48 Washer- Lock 048164812 8 49 Nut 040499906 8 50 Washer- Lock Grounding 040500213 16 52 Washer- Lock Grounding 040500212 16 426 Cable To Comp. Control Box 070829981 1 317 Bracket- Starter Mounting 350257302 4 RPL 7000000 / Page 33

Starter, Free Standing - Field Installed Units with MicroTech 200 Control Box Junction Box 2 5 13 3 21 14 6 7 36 37 35 424 425 426 427 9 11 8 304 111 Ref. Description Specification Part Qty. No. Number 2 Door 070414302 1 3 Hinge- Painted 070806401 1 5 Latch- Door 350065401 1 6 Screw.37 x 1.0 000086100 4 7 Washer- Lock.375 ZPS 048164812 4 8 Back Panel 070409601 1 9 Terminal- Power 735042913 1 11 Terminal Block- 310 MA TB1 & TB2 030372704 2 13 Bushing 1.75" Diameter 028387100 2 14 Terminal 1 144-177 RLA Max. Motors 072960308 6 Terminal 1 206 RLA Max. Motors 072960309 6 Terminal 1 238-348 RLA Max. Motors 072960312 6 Terminal 1 399-460 RLA Max. Motors 072960316 6 21 Washer- Plain.375 ZPS 040500316 4 35 Screw 735033230 10 36 Washer- Plain 040500316 10 37 Washer- Lock 048164812 10 111 Shelf- Control/Terminal Boxes 070013205 1 304 Bracket- Terminal Box 18" dia. evap. 070013211 5 Bracket- Terminal Box 20" dia. evap. 070013212 5 Bracket- Terminal Box 22" dia. evap. 070013213 5 424 Screw.25 x.75 735033204 6 425 Washer- Plain.25 ZPS 040500305 6 426 Washer- Lock.25 ZPS 048164808 6 427 Nut- Hex.25-20 040499901 6 1 Motor RLA is indicated on the compressor data plate. RPL 7000000 / Page 34

Starter, Free Standing - Field Installed Units with MicroTech II Control Box Junction Box Junction Box Mounting 421 420 42 41 424 426 427 Junction Box Ass'y Detail 1 35 36 2 3 14 37 304 111 13 6 7 21 9 Junction Box Terminal Block Ass'y 11 8 Terminal Block Ass'y (Detail Below) 893 891 892 1 896 RPL 7000000 / Page 35

Starter, Free Standing - Field Installed Units with MicroTech II Control Box Junction Box Ref. Description Specification Part Qty. No. Number 1 Box Assembly 071503852 1 2 Door 070414302 1 3 Hinge- Painted 070806401 1 6 Screw- Backplate.37 x 1.0 000086100 4 7 Washer, Lock- Backplate.375 ZPS 048164812 4 8 Back Panel 070409601 1 9 Terminal- Power 735042913 1 11 Terminal Block- 310 MA TB1 & TB2 030372704 2 13 Bushing 1.75" Diameter 028387100 2 14 Terminal 1 144-206 RLA Max. Motors 072960308 6 Terminal 1 238 RLA Max. Motors 072960309 6 Terminal 1 277-298 RLA Max. Motors 072960310 6 Terminal 1 348 RLA Max. Motors 072960312 6 Terminal 1 399 RLA Max. Motors 072960314 6 Terminal 1 460 RLA Max. Motors 072960316 6 21 Washer, Plain- Backplate.375 ZPS 040500316 4 35 Screw- Junction Box to Shelf 735033232 4 36 Washer, Plain- Junction Box to Shelf 040500316 4 37 Washer, Lock- Junction Box to Shelf 048164812 4 41 Extension- Control Box 330356002 1 42 Cover- Control Box Extension 330355902 1 111 Shelf- Terminal Box 330367401 1 304 Bracket- Terminal Box 18" dia. evap. 070013261 1 Bracket- Terminal Box 20" dia. evap. 070013262 1 Bracket- Terminal Box 22" dia. evap. 070013263 1 420 Screw- Comp. Control Box to Extension.164-32 x.5 046093801 2 421 Washer, Lock- Comp. Control Box to Extension.164 ZPS 040500204 2 424 Screw- Extension to Junction Box.25 x.75 735033204 6 426 Washer, Lock- Extension to Junction Box.25 ZPS 048164808 6 427 Nut, Hex- Extension to Junction Box.250-20 040499901 6 891 Bracket- Terminal Block 330421001 1 892 Terminal Block 330274001 1 893 Cover- Terminal Block 330500601 1 896 Hex Nut 032333302 2 N/S Latch- Door 350065401 1 N/S= Not Shown on diagram. 1 Motor RLA is indicated on the compressor data plate. RPL 7000000 / Page 36

Differential Pressure Switch Factory Mounted & Wired (Code 33= B, C or E) Switches, Wells, Power Cables, Fittings 667A 667C 667B 667 656 411 412 Wiring- MicroTech 200 Control CHW1- NO CW1- NO Well Detail (ref. 667) Until 5/04 CW1 & CHW1- C Wiring- MicroTech II Control 651 651 Ref. Description Part Qty.* No. Number 411 Cable- Evaporator DPS MicroTech 200 Control 071543662 1 MicroTech II Control (until 5/04) 074608901 16 ft. MicroTech II Control (5/04 & later) 330571402 1 412 Cable- Condenser DPS MicroTech 200 Control 071543661 1 MicroTech II Control (until 5/04) 074608901 16 ft. MicroTech II Control (5/04 & later) 330571402 1 651 Differential Pressure Switch (until 5/04) 070180519 2 Differential Pressure Switch (5/04 & later) 330571401 2 656 Flare Nut (2 per tube) (until 5/04) 000028600 8 667 Sensor Well (until 5/04) 072867501 4 667A Elbow (until 5/04) 001276600 4 667B Tube (until 5/04) 070221602 4 667C Nozzle (until 5/04) 072867511 4 667 Sensor Well (5/04 & later) 047441511 4 N/S Fitting (5/04 & later) 735048013 4 CF- NO EF- NO EF & CF- C NOTES: The water pressure differential switch is an optional component. It is factory installed and wired when code 33= E (evaporator only), C (condenser only) or B (both condenser and evaporator). The switches used for either the MicroTech 200 or the MicroTech II control types are the same as are the wells. However the schematic designations are different. MicroTech 200 units designate the Evaporator & Condenser switches as CHW1 & CH1, while the MicroTech II units designate the same switches as EF1 & CF1. The only component part number difference of note are the power cables. *Quantities are based on the presence of both DPS (Code 33= B). If code 33= E or C part numbers 651 & 656 quantities are 1 & 4 respectively, and only one cable (411 if C33= E or 412 if C33= C) is used. If only one DPS is used, the well (ref. # 667) has a quantity of 2-072867501 (used on the vessel with the DPS) and 2-047441511 (used on the vessel without the DPS). N/S= Not shown on diagram. Differential Pressure Switch- None (Code 33= Y) Wells Description Part Qty. Number Sensor Well (Evap & Cond in/out nozzles) 047441511 4 RPL 7000000 / Page 37

Hot Gas Bypass- Until 10/02 Valves, Connectors The Hot Gas Bypass was redesigned in late 2002. The primary changes were the removal of the shutoff valve, the repositioning of the ball valve, and a new HGBP valve (associated tubing changed as a result). 706 Check Valve 704 702 227 297 Ref. Description Specification Part Qty. No. Number 227 Adapter 735883901 1 297 Tee- Reducer 2.625" to 1.625" 041118058 1 702 Valve- Ball 1.625" ODS 036562907 1 704 Valve- Hot Gas Bypass 27 Ton 070894501 1 706 Valve- Shutoff 1.62" 735039963 1 N/S Cable HGBP Valve to Control Box 070813549 1 N/S= Not shown on diagram. RPL 7000000 / Page 38

Hot Gas Bypass- 10/02 to Present Valves, Connectors 80 140 91 202 201 200 15 50 Ref. Description Specification Part Qty. No. Number 15 Adapter 735883901 1 50 Reducer 2.125" to 1.625" 041116624 1 80 Valve- Hot Gas Bypass 24V 25 Ton 070894504 1 91 Insulation- ¾" 047662050 * 140 Valve- Ball 1.625" 330286007 1 200 Adapter 22" Evap dia. only 735049705 1 201 Flange Kit 22" Evap dia. only 735016402 1 202 Gasket 22" Evap dia. only 070199112 1 N/S Cable Hot Gas Valve to Control Box 330287404 1 N/S= Not shown on diagram. *Quantity in square feet, as needed. RPL 7000000 / Page 39

Condenser & Evaporator Valves Relief Valves, Shutoff Valves 331 330 22 21 20 22 330 331 Ref. Description Specification Part Qty. No. Number 21 Valve- Shut Off 1" NPT 735039977 1 22 Valve- Relief 200 PSI 735045817 3 330 Valve- Shutoff.625" 735039929 3 Cap for Shutoff Valve 071556909 3 331 Flare Cap.625" 073243901 3 RPL 7000000 / Page 40

Liquid Line - Thermal Expansion Valve Expansion Valve, Ball Valve, Sight Glass, King Valve, Flanges, Gaskets, O'Rings, Pilot Valve Sensor Well 82 80 81 190 140 142 End View King Valve to Condenser Detail 330 251 331 254 142 60 Condenser 251 20 21 60A 60B 253 255 252 313 314 312 Pilot Valve Bulb Detail 308 Pressure Connector (ref. #304) Detail 338 304 300 190 185 Pilot Valve Tubing Detail 200 221 260 262 264 RPL 7000000 / Page 41

Liquid Line - Thermal Expansion Valve Expansion Valve, Ball Valve, Sight Glass, King Valve, Flanges, Gaskets, O'Rings, Pilot Valve Sensor Well Ref.# Description Specification Part No. Qty. 20 Adapter- 1.625" 16" dia. cond. 735049701 1 Adapter- 2.625" 18" & 20" dia. cond. 735049702 1 21 Flange Kit- Liquid Line to King Valve 16" dia. cond. 735016401 1 Flange Kit- Liquid Line to King Valve 18" & 20" dia. cond. 735016407 1 60 Schrader Valve 071100801 1 Schrader Valve Cap 032943500 1 Schrader Valve Core 026541100 1 60A Saddle- Sight Glass 16" dia.cond. 330743301 3 1 Saddle- Sight Glass 18" & 20" dia. cond. 330508701 3 1 60B Sight Glass 022427700 1 80 Flange- Evaporator Inlet 18" & 20" dia. evap. 070350502 1 Flange- Evaporator Inlet 22" dia. evap. 330104002 1 81 O'Ring- Evaporator Inlet Flange 18" & 20" dia. evap. 735043674 1 O'Ring- Evaporator Inlet Flange 22" dia. evap. 735073633 1 82 Screw- Evaporator Inlet Flange 18" & 20" dia. evap. 735033865 4 Screw- Evaporator Inlet Flange 22" dia. evap. 735033968 4 140 Expansion Valve- Main 125 Ton 735048629 1 Cap for 125 Ton Expansion Valve 071556912 1 Gasket Kit for 125 Ton Expansion Valve 735048676 1 Flange Kit for 125 Ton expansion Valve 735048652 1 Expansion Valve- Main 150 Ton 735048609 1 Cap for 150 Ton Expansion Valve 071556912 1 Gasket Kit for 150 Ton Expansion Valve 735048676 1 Expansion Valve- Main 180 Ton 735048625 2 1 Cap for 180 Ton Expansion Valve 071556912 1 Flange Kit for 180 Ton Expansion Valve 735048653 1 Expansion Valve- Main 250 Ton 735048624 1 Cap for 250 Ton Expansion Valve 071556912 1 Gasket Kit for 250 Ton Expansion Valve 735048675 1 Flange Kit for 250 Ton expansion Valve 735048654 1 142 Reducer- 2.625" to 1.625" 125 & 150 Ton Expansion Valve 041116630 1 Reducer- 2.625" to 2.125" 180 Ton Expansion Valve 041116629 1 185 Flare Nut 000136100 1 190 Coupling- Half Union.50F x.25p 735044212 1 2 This valve is no longer manufactured. When existing stock is depleted it may be replaced with part #735048624 & qty. 2 reducers part # 041116629. 3 Prior to 10/04 the saddle was pn 070736401 and the sight glass was pn 022427700. If replacing an old saddle or glass with a new component, order both parts. RPL 7000000 / Page 42

Liquid Line - Thermal Expansion Valve Expansion Valve, Ball Valve, Sight Glass, King Valve, Flanges, Gaskets, O'Rings, Pilot Valve Sensor Well Ref. Description Specification Part Qty. No. Number 200 Expansion Valve- Pilot 125, 150, 180 Ton Main TXV 735048618 1 Cap for Pilot Valve 735048618 071556313 1 Expansion Valve- Pilot 250 Ton Main TXV 735048665 1 Cap for Pilot Valve 735048665 071556313 1 221 Reducer.625ODS x.375ods 041116509 1 251 Valve- Main Liquid (King)- 2" 16" dia. cond. 735039810 1 Valve- Main Liquid (King)- 2.625" 18" & 20" dia. cond. 735039811 1 252 Screw- 2" King Valve.50 x 3 735033852 4 Screw- 2.625" King Valve.625 x 4 735033955 4 253 Gasket- 2" King Valve 070199107 1 Gasket- 2.625" King Valve 070199108 1 254 Cap- King Valve 2" Valve 071556901 1 Cap- King Valve 2.625" Valve 071556904 1 255 Flange- Liquid Line 2.0" P 350257801 1 260 Strainer 735030506 1 262 Ball Valve.625" 330286003 1 264 Reducer.88ODM x.625ods 041116611 1 300 Tee Assembly 735061434 1 304 Pressure Connector 070811202 1 308 Flare Nut 1 000028600 1 312 Valve Core 1 026541100 1 313 Schrader Valve 1 071100801 1 314 Valve Cap 032943500 1 330 Valve- Shutoff 2.375" Flare 735039907 1 Cap for Shutoff Valve 071556909 1 331 Flare Cap 2 000540900 1 338 Sensor Well- Pilot Valve located at top of evaporator 735946401 1 1 Included in pressure connector (ref. 304) assembly. 2 Only used on units with 18" or 20" condensers. RPL 7000000 / Page 43

Liquid Line- Electronic Expansion Valve Expansion Valve, Ball Valve, Sight Glass, King Valve, Flanges, Gaskets, O'Rings 82 81 80 83 140 82 81 80 83 72 140 73 73 22 21 20 23 50 60 22 21 20 23 31 50 60 61 Piping for 250 Ton Valve Stack E22C20 Piping for 150 Ton Valve Stacks E18C16 E20C18 E22C20 82 81 80 83 72 140 251 Condenser 73 254 255 253 252 End View King Valve to Condenser Detail 22 21 20 23 31 50 60 Piping for 150 Ton Valve Stack E20C16 RPL 7000000 / Page 44

Liquid Line- Electronic Expansion Valve Expansion Valve, Ball Valve, Sight Glass, King Valve, Flanges, Gaskets, O'Rings Ref. Description Specification Part Qty. No. Number 20 Coupling 074606801 1 21 Flange 074606701 1 22 Gasket- Flange 070199108 1 23 Screw- Flange.62 x 2.0 735033862 4 31 Reducer 150 Ton EEXV 041116630 1 50 Valve- Ball 150 Ton EEXV 330286007 1 Valve- Ball 250 Ton EEXV 330286008 1 60 Schrader Valve 071100801 1 Schrader Valve Cap 032943500 1 Schrader Valve Core 026541100 1 Sight Glass Saddle 330508704 1 Sight Glass Cap 330508701 1 61 Reducer 250 Ton EEXV only 041116529 1 72 Reducer 150 Ton EEXV only 041116629 1 73 Coupling 330823502 1 80 Flange Kit 16" & 18" Condenser 735016404 1 Flange Kit 20" Condenser 330743201 1 81 Screw- Flange 20" Condenser 735033967 4 82 Gasket- Flange 20" Condenser 070199104 1 83 Adapter 735049717 1 140 Valve- Electronic Expansion 150 Ton (Code 29 = BY) 330386204 1 Valve- Electronic Expansion 250 Ton (Code 29 = CY) 330386201 1 251 Valve- Main Liquid (King)- 2" 16" dia. cond. 735039810 1 Valve- Main Liquid (King)- 2.625" 18" & 20" dia. cond. 735039811 1 252 Screw- 2" King Valve.50 x 3 735033852 4 Screw- 2.625" King Valve.625 x 4 735033955 4 253 Gasket- 2" King Valve 070199107 1 Gasket- 2.625" King Valve 070199108 1 254 Cap- King Valve 2" Valve 071556901 1 Cap- King Valve 2.625" Valve 071556904 1 255 Flange- Liquid Line 2.0" P 350257801 1 RPL 7000000 / Page 45

Unit Insulation Description Specification Part Quantity Number Insulation 0.75 thickness 047662050 Square feet - As needed RPL 7000000 / Page 46

Condenser Nomenclature Dataplate used until 8/03 Dataplate beginning 8/03 Model Number- Condenser C 18 09 B L 2 R A Condenser Type C= Standard S= Split Head Condenser Diameter 16, 18, 20 Condenser Length (in feet) 09, 12 Condenser Tube Count 16" Condenser Diameter B= 128 C= 98 18" Condenser Diameter B= 171 C= 137 20" Condenser Diameter B= 248 C= 212 D= 192 Condenser Tube Type see table on next page Contact Daikin Applied for Split Head tube counts Nozzle Configuration A= Grooved (standard) B= Flanged D= Marine Water Box- Grooved F= Marine Water Box- Flanged Inlet Nozzle Location L= Left R= Right Number of Water Passes 1, 2, 3 RPL 7000000 / Page 47

Condenser Heads To properly identify Condenser Heads, please contact Daikin Applied with the Unit SO and/or GO Number; and the Unit Serial Number. If available, also include the Condenser Style Number and Serial Number. Head Types Standard Grooved Standard Flanged Water Box Grooved Water Box Flanged Connection Return Connection Return Connection Return Connection Return 1- Pass 2- Pass 3- Pass RPL 7000000 / Page 48

Condenser Sight Glass, Flange, Tubes, Head Gaskets Return Head 355 Front View 118 Shut Off Valve** 352 Connection Head Shut Off Valve* End View King Valve* 110 King Valve* 116 100 110 *See Liquid Line Section ** See Evap & Cond. Relief Valve Section Ref. Description Specification Part Qty. No. Number 100 Tubes- See Tube Table below 110 Sight Glass 350229501 1 116 Flange- Liquid Line 16" dia. Cond. 350257801 1 Flange 18" & 20" dia. Cond. 071580505 1 118 Flange- Reducing 16" dia. Cond. 073079801 1 Flange- Reducing 18" dia. Cond. 070318401 1 Flange- Reducing 20" dia. Cond. 350262101 1 Tube Table Tube Code Wall 9 12 (6th digit) Thickness foot foot L.025 330441407 330441408 N.028 330441424 330441425 P.035 073238578 073238577 RPL 7000000 / Page 49

Condenser Gaskets- Dish Head Split-Head Condenser Gaskets (Code 16= Sxxxx) Contact Daikin Applied with the Unit SO and/or GO Number; and the Unit Serial Number. If available, also include the Condenser Style Number and Serial Number. 16 Inch Condenser, 150 PSI (Code 16= C16xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket, Head 070304642 2 2 Pass, 150 PSI, Dish Heads, non-asme 352 Gasket, Connection Head 070304642 * 1 355 Gasket, Return Head 070304642 1 3 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket, Head 070304642 * 2 * Use Gasket + Channel 070189802 (qty.= 2 ft per head). 16 Inch Condenser, 300 PSI (Code 16= C16xx) Ref. # Description Part Number Qty. 1 Pass, 300 PSI, Dish Heads, non-asme 352/355 Gasket, Head 070304611 2 2 Pass, 300 PSI, Dish Heads, non-asme 352 Gasket, Connection Head 070304611 ** 1 355 Gasket, Return Head 070304611 1 3 Pass, 300 PSI, Dish Heads, non-asme 352/355 Gasket, Head 070304611 ** 2 ** Use Gasket + Channel 070189801 (qty.= 2 ft per head). RPL 7000000 / Page 50

Condenser Gaskets- Dish Head Split-Head Condenser Gaskets (Code 16= Sxxxx) Contact Daikin Applied with the Unit SO and/or GO Number; and the Unit Serial Number. If available, also include the Condenser Style Number and Serial Number. 18 Inch Condenser (Code 16= C18xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket, Head 070304643 2 2 Pass, 150 PSI, Dish Heads, non-asme 352 Gasket Kit, Connection Head 333849803 1 355 Gasket, Return Head 070304643 1 3 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket Kit, Head 333849803 2 20 Inch Condenser (Code 16= C20xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket, Head 070304644 2 2 Pass, 150 PSI, Dish Heads, non-asme 352 Gasket Kit, Connection Head 333849804 1 355 Gasket, Return Head 070304644 1 3 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket Kit, Head 333849804 2 RPL 7000000 / Page 51

Condenser Gaskets- Water Box Heads Split-Head Condenser Gaskets (Code 16= Sxxxx) Contact Daikin Applied with the Unit SO and/or GO Number; and the Unit Serial Number. If available, also include the Condenser Style Number and Serial Number. 16 Inch Condenser, 150 PSI (Code 16= C16xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Water Box Heads, non-asme 352/366 Gasket, Head 070304642 4 2 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket, Water Box to Shell 070304642 * 1 355 Gasket, Return Head 070304642 1 366 Gasket, Water Box Cover 070304642 * 1 3 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket, Water Box to Shell 070304642 * 2 366 Gasket, Water Box Cover 070304642 * 2 * Use Gasket + Strip 073258603 (qty.= 2 ft per head). 16 Inch Condenser, 300 PSI (Code 16= C16xx) Ref. # Description Part Number Qty. 1 Pass, 300 PSI, Water Box Heads, non-asme 352/366 Gasket, Head 074521611 4 2 Pass, 300 PSI, Water Box Heads, non-asme 352 Gasket, Water Box to Shell 074521611 ** 1 355 Gasket, Return Head 074521611 1 366 Gasket, Water Box Cover 074521611 ** 1 3 Pass, 300 PSI, Water Box Heads, non-asme 352 Gasket, Water Box to Shell 074521611 ** 2 366 Gasket, Water Box Cover 074521611 ** 2 ** Use Gasket + Strip 073258602 (qty.= 2 ft per head). RPL 7000000 / Page 52

Condenser Gaskets- Water Box Heads Split-Head Condenser Gaskets (Code 16= Sxxxx) Contact Daikin Applied with the Unit SO and/or GO Number; and the Unit Serial Number. If available, also include the Condenser Style Number and Serial Number. 18 Inch Condenser (Code 16= C18xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Water Box Heads, non-asme 352/366 Gasket, Head 070304643 4 2 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket Kit, Water Box to Shell 333849903 1 355 Gasket, Return Head 070304643 1 366 Gasket Kit, Water Box Cover 333850003 1 3 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket Kit, Water Box to Shell 333850003 2 366 Gasket Kit, Water Box Cover 333850003 2 20 Inch Condenser (Code 16= C20xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Water Box Heads, non-asme 352/366 Gasket, Head 070304644 4 2 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket Kit, Water Box to Shell 333849904 1 355 Gasket, Return Head 070304644 1 366 Gasket Kit, Water Box Cover 333850004 1 3 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket Kit, Water Box to Shell 333849904 2 366 Gasket Kit, Water Box Cover 333850004 2 RPL 7000000 / Page 53

Evaporator Nomenclature Dataplate used until 8/03 Dataplate beginning 8/03 Model Number- Evaporator E 18 09 B E 2 R A Evaporator Evaporator Diameter 18, 20, 22 Nozzle Configuration A= Grooved (standard) B= Flanged C= Marine Water Box- Grooved E= Marine Water Box- Flanged Evaporator Length (in feet) 09, 12 Evaporator Tube Count 18" Evaporator Diameter B= 86 C= 76 20" Evaporator Diameter B= 116 C= 102 22" Evaporator Diameter B= 138 C= 122 Inlet Nozzle Location L= Left R= Right Number of Water Passes 1, 2, 3 Evaporator Tube Type see table on next page RPL 7000000 / Page 54

Evaporator Heads To properly identify Evaporator Heads, please contact Daikin Applied with the Unit SO and/or GO Number; and the Unit Serial Number. If available, also include the Evaporator Style Number and Serial Number. Head Types Standard Grooved Standard Flanged Water Box Grooved Water Box Flanged Connection Return Connection Return Connection Return Connection Return 1- Pass 2- Pass 3- Pass RPL 7000000 / Page 55

Evaporator Sight Glass, Flange, Tubes, Head Gaskets Return Head Sensor Well* Shut Off Valve** 355 352 Connection Head *See Liquid Line Section ** See Evap & Cond. Relief Valve Section 116 Shut Off Valve** 110 Ref. Description Specification Part Qty. No. Number N/S Tubes- See Tube Table below 110 Sight Glass 350229501 1 116 Flange- Liquid Line 070251902 1 Tube Table Tube Code Wall 9 12 (6th digit) Thickness foot foot E.025 073238596 073238590 F.028 330441417 330441418 Q.035 330441413 330441414 RPL 7000000 / Page 56

Evaporator Gaskets- Dish Head 18 Inch Evaporator (Code 8= E18xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket, Head 070304643 2 2 Pass, 150 PSI, Dish Heads, non-asme 352 Gasket Kit, Connection Head 333849803 1 355 Gasket, Return Head 070304643 1 3 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket Kit, Head 333849803 2 20 Inch Evaporator (Code 8= E20xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket, Head 070304644 2 2 Pass, 150 PSI, Dish Heads, non-asme 352 Gasket Kit, Connection Head 333849804 1 355 Gasket, Return Head 070304644 1 3 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket Kit, Head 333849804 2 22 Inch Evaporator (Code 8= E22xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket, Head 070304645 2 2 Pass, 150 PSI, Dish Heads, non-asme 352 Gasket Kit, Connection Head 333849805 1 355 Gasket, Return Head 070304645 1 3 Pass, 150 PSI, Dish Heads, non-asme 352/355 Gasket Kit, Head 333849805 2 RPL 7000000 / Page 57

Evaporator Gaskets- Water Box Heads 18 Inch Evaporator (Code 8= E18xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Water Box Heads, non-asme 352/366 Gasket, Head 070304643 4 2 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket Kit, Water Box to Shell 333849903 1 355 Gasket, Return Head 070304643 1 366 Gasket Kit, Water Box Cover 333850003 1 3 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket Kit, Water Box to Shell 333850003 2 366 Gasket Kit, Water Box Cover 333850003 2 20 Inch Evaporator (Code 8= E20xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Water Box Heads, non-asme 352/366 Gasket, Head 070304644 4 2 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket Kit, Water Box to Shell 333849904 1 355 Gasket, Return Head 070304644 1 366 Gasket Kit, Water Box Cover 333850004 1 3 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket Kit, Water Box to Shell 333849904 2 366 Gasket Kit, Water Box Cover 333850004 2 22 Inch Evaporator (Code 8= E22xx) Ref. # Description Part Number Qty. 1 Pass, 150 PSI, Water Box Heads, non-asme 352/366 Gasket, Head 070304645 4 2 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket Kit, Water Box to Shell 333849905 1 355 Gasket, Return Head 070304645 1 366 Gasket Kit, Water Box Cover 333850005 1 3 Pass, 150 PSI, Water Box Heads, non-asme 352 Gasket Kit, Water Box to Shell 333850005 2 366 Gasket Kit, Water Box Cover 333850005 2 RPL 7000000 / Page 58

Compressor Nomenclature Model Number- Compressor CE 050 K ZY 10 B Compressor Impeller Size 048= 4.8" 050= 5.0" Impeller Type H, J, K, M Motor Voltage See Compressor Section Motor Table Motor Horsepower See Compressor Section Motor Table Gear Ratio Code See Compressor Section Gear Table Style Number- Compressor 0 923456010 FR01 Always zero Compressor Unit G.O. No. Motor Style Number The motor style number is the part number. See the RPL compressor section for list of motor, stator & rotor/shafts. RPL 7000000 / Page 59