Electric Table Truck Operating Instructions ETAD Series BEFORE YOU BEGIN Electric TableTruck Model ETAD35 ETAD75 Instruction Manual Read this operation manual completely before using. thoroughly understand and follow all safety instructions. if this is lost, please contact your local supplier for a new copy. if the warning/caution decal on the unit is lost, please contact your local supplier for a new copy. Note: On this manual, WARNING means the danger, which can lead death or serious injury. CAUTION means the danger, which can lead slight injury or property damage. Electric Table Truck ETAD Series Eoslift Warehousing Equipment Corp. No.99, Yanjia Road, Yuantong Town, Haiyan, Zhejiang
CONTENTS Warnings Cautions 3 Name of Parts Daily Inspection 5 Operation Instruction 6 Structural Data Form 7 Maintenance 8 Hydraulic Circuit 9 Parts List Page Page Page Page Page Page Page Page 5 Page 6.Warnings. DO NOT allow another person to stand in front of or behind lifter when it starts to move.. ALWAYS travel with table in lowered position. Load could fall down. 3. NEVER sit, stand or ride on platform. SEVERE PERSONAL INJURY could result.. NEVER go under platform. SEVERE PERSONAL INJURY or DEATH could result. 5. DO NOT use in area of multilevel floor surface that could create loss control and result in SEVERE INJURY and PROPERTY DAMAGE. 6. DO NOT use lifter on slope, uneven or soft surface. Lifter may become uncontrollable. SEVERE PERSONAL INJURY and PROPERTY DAMAGE could result. 7. KEEP FEET CLEAR of rolling wheels that could result in SEVERE PERSONAL INJURY. 8. DO NOT load one fork more than the other and DO NOT load tips on table. SEVERE PERSONAL INJURY and PROPERTY DAMAGE could result. 9. DO NOT overload lifter. ALWAYS stay within designated capacity and load center rating. SEVERE PERSONAL INJURY and PROPERTY DAMAGE could result. 0. SHEARING HAZARD. NEVER place hands or feet under lowering table. SEVERE PERSONAL INJURY could result.. NO FIRE during charging. Read battery operation manual.. HIGH VOLTAGE. Disconnect battery socket before opening control panel box. 3. DO NOT remove battery terminal cover. Short-circuit or electric shock could occur..cautions. Read the operation manual completely before using and thoroughly understand and follow all safety instructions.. This lifter is designed to use with stable uniform load on a solid lever floor. DO NOT use the lifter for any other purpose than its intended use. 3. TRAINED personnel shall operate lifter only. OPERATOR shall read Operation Manual completely and thoroughly understand the controls and operation of this equipment BEFORE operating the lifter.. ALWAYS observe lifter and ALWAYS stay at the controls while the lifter is in motion, RELEASE controls and STOP lifter immediately if load on lifter appears to become unstable. NEVER leave the loaded lifter unattended unless the table is in the fully lowered position and the lifter is locked reliably. 5. DO NOT slide the load on or off the table. The lift may move allowing the load to fall. SEVERE PERSONAL INJURY and PROPERTY DAMAGE could result. 6. DO NOT use lifter with unstable, unbalanced or loosely stacked load. Unbalanced loads may become unstable and fall. SEVERE PERSONAL INJURY and PROPERTY DAMAGE could result. 7. Qualified personnel must perform ALL lifter service only. 8. ALWAYS keep feet, hands and fingers away from casters, load wheels and all moving components. SEVERE INJURY could result. 9. ALWAYS perform maintenance and inspections with lifter unloaded. 0. Prolonged continuous working might cause damage of power pack.. Stop operation if temperature of hydraulic oil is too high.the lifter is NOT waterproof and is intended to be used in a dry environment.
3.Daily Inspection Daily inspection is effective to find the malfunction or fault on lift table.check lift table on the following points before operation. 5.Operation Instruction How to use the brake CAUTION CAUTION DO NOT use lift table if any malfunction or fault is found. Brake lift table when not moving it in order to prevent sudden movement. The brake is equipped with the swivel caster on the right side. () Breaking the wheel, press the brake pedal. () Releasing the brake, lift up the brake pedal. () Check for scratch,bending or cracking on the lift table. () Check if there is any oil leakage from the cylinder. (3) Check the vertical creep of the table. () Check the smooth movement of the wheels. (5) Check the function of brake. (6) Check if all the bolts and nuts are tightened firmly..name OF PARTS ETAD35 ETAD75 6. LIFTING UP FORKS CAUTION. DO NOT overload lifter. Stay within its rated capacity.. Prolonged continuous working might cause damage of hydraulic power pack. 3. Stop operation if temperature of hydraulic oil is too high. Push the button UP and the table lifts up..handle.switch 3.Brake Pedal.Platform 5. Link 6.Guide rail 3
9.CHARGING THE BATTERY TYPE OF PUMP A GR.0.5-0.5 D GR.0.5-0.75 B GR.0.5-0.5 J GR.0.5-0.9 C GR.0.5-0.56 Z GR.0.5 -.6 Curve S defines the maximum running time of the D.C. Motor expressed in a minutes. Curve S3 expresses the on-off ratio in % which has value S3 in a total work cycle (00%). () Check the quantity of Battery fluid. If it is insufficient, add the battery solution according to battery operation manual. () Disconnect the battery socket. (3) Connect the charging port of battery socket to the battery charger. 0.REGULAR INSPECTION () Check the items expressed in daily inspection (daily). () Lubricate with grease the guides where roller moves. Also, lubricate the grease nipples. (Every month) (3) Lubricate all the pivoting points and axles. (Every 6 months) () Replace the hydraulic oil for the first time: Accumulated working ten hours (5) Replace the hydraulic oil. (Every months) 7.LOWERING TABLE CAUTION DO NOT lower table with load too fast and stop suddenly. Impact load could be created and lifter could be damaged..trouble SHOOTING TROUBLE CAUSE REPAIR Platform doe s no t rise.faulty wiring..check the wiring referring while motor does not run. to the actual wiring diagram. Push the button DOWN and the table lower. 8.MOVING THE LIFTER.Battery socket is disconnected 3.Battery charge is Platform does not rise while motor insufficient. runs..faulty adjustment of relief valve..faulty hydraulic pump..connect the battery socket. 3.Charge the battery..adjust relief valve again..replace power pack. () Make the load stable to prevent it to fall. () Lower the table down. (3) Release the brake and move the lifter. WARNING DO NOT move lifter on slope or inclined surface, otherwise lifter become uncontrollable and create danger. 3.Shortage of hydraulic 3.Add oil. oil. Vertical creep of table..oil leakage in power pack..replace lowering valve..oil leakage form.check hydraulic circuit and repair. hydraulic circuit. Oil leakage from cylinder. Faulty sealing. Replace sealing. Oil leakage from piping or joint. Insufficient tightening or Tighten joint again or Replace seal. seal in valid. Oil leakage from air breather. Excessive quantity of oil. Reduce oil quantity. 5
. SPECIFICATIONS ETAD35 Model ETAD35 ETAD75 Capacity (kg) 350 750 Table (mm) 50 00 50 00 Min. table height (mm) 95 50 Max. Table height (mm) 600 0 Lifting stroke (mm) 05 930 Motor (KW) 0.7 0.7 Work cycle of hydraulic power pack 3 times of table moving up-down per 0 min. Approx. numbers of lifting at full charge and with full 5 0 load (times) Approx. time required lifting up table. (Sec) 5 5 Wheel (mm, diameter) 50 50 Handle height (mm) 80 80 Weight (kg) 83 5 3. HYDRAULIC CIRCUIT/WIRING DI AGRAM/ACTUAL WI RING DIAGRAM 3. 液压回路 / 接线图 6 7
LIFT TABLE SPARE PARTS LIST ETAD35 NO. DESCRIPTION QTY. NO. DESCRIPTION QTY. 6 Washer 89 Nut M0 Seal cover φ50 φ58 6.5 6 Charger 63 Spring washer 90 Safety rod Y-ringφ50 φ58 8. 7 Washer 5 6 Hex screw M 30 9 Screw M0 0 3 Cylinder cover 8 Screw M5 0 65 Hex screw M6 0 9 Bushing 0 Retainer ring 9 Screw M5 0 66 Washer 6 93 External scissors for chassis 5 O-ring φ56.65 30 Fuse 67 Covering plate 9 Internal scissors for chassis 6 Piston rod 3 Spring washer 5 68 Nut M8 95 Bushing 7 Bushing 3 Nut M5 69 Spring washer 8 8 96 Roller for chassis 8 Bushing 33 Screw M5 6 70 Screw M8 0 97 Pin axle for chassis 9 Pin axle 3 Fuse 7 Nut M0 6 98 Pin axle for table 0 Snap ring 50 35 Screw M 6 7 Rear wheel 99 Bushing Cylinder 36 Nut M8 73 Screw M0 5 6 00 Oil cup 5 Prevent burst valve 3 Spring Seal ring 8 37 38 39 Washer 8 Screw M0 6 Spring washer 0 7 75 76 Front wheel Chassis Screw M6x8 0 0 03 Screw M6 6 Cable Cable velcro strap 5 Prevent burst joint 0 Washer 0 77 Table 6 Seal ring Switch 7 High pressure hose Battery case weldment 8 Joint 3 Covering plate 9 Split Pin Pad 0 Covering plate 5 Battery Washer 0 6 Insulator pad Spring washer 0 7 Insulation case 3 Screw Mx0 8 8 Screw M8 0 Battery indicator 9 Battery securing tag 5 Screw M3 0 50 Screw M5 6 5 Connector block 78 Roller for table 5 Screw M5 0 79 Bushing 53 Fixing plate 80 Retaining ring for axle 0 5 Joint board 8 Internal scissors for table 55 Lifting limit switch 8 External scissors for table 56 Spring washer 6 83 Screw M8 6 57 Nut M6 8 Pin axle for scissors 58 Hydraulic power pack 85 Washer 59 Terminals 86 Split pin 3. 6 60 Handle 87 Nut M6.5 6 Nut M 88 Spring pin 8 30 8 9
ETAD75 LIFT TABLE SPARE PARTS LIST ETAD75 NO DESCRIPTION QTY NO DESCRIPTION QTY Seal cover φ60 φ68 6.5 5 Screw M3 0 Y-ringφ60 φ70 6 6 Connector block 3 Cylinder cover 7 Charger Retainer ring 8 Washer 5 0 5 O-ring φ65.65 9 Screw M5 0 6 Piston rod 30 Screw M5 0 7 Bushing 3 Fuse 8 Bushing 3 Spring washer 5 6 9 Pin axle 33 Nut M5 6 0 Snap ring 60 3 Screw M5 6 Cylinder 35 Fuse Prevent burst valve 36 Screw M 6 3 Spring 37 Nut M8 Seal ring 8 38 Washer 8 6 5 Prevent burst joint 39 Screw M0 6 6 Seal ring 0 Spring washer 0 0 7 High pressure hose Washer 0 8 Joint Switch 9 Split Pin 3 Battery case weldment 0 Covering plate Covering plate Washer 0 5 Pad Spring washer 0 6 Battery 3 Screw Mx0 8 7 Insulator pad Battery indicator 8 Insulation case 9 Screw M8 0 8 77 Internal scissors for table 50 Battery securing tag 78 External scissors for table 5 Hydraulic power pack 79 Screw M8 6 6 5 Terminals 80 Pin axle for scissors 53 Handle 8 Washer 5 Nut M 8 Split pin 3. 6 6 55 Hex screw M6 0 83 Nut M6.5 6 56 Washer 6 8 Oil cup 3 57 Covering plate 85 Internal scissors for chassis 58 Screw M5 0 86 Spring pin 8 30 59 Lifting limit switch 87 Nut M0 0
60 Spring washer 6 88 Safety rod 6 Nut M6 89 Bushing 8 6 Nut M8 90 Screw M0 0 63 Spring washer 8 9 9 External scissors for chassis 6 Washer 9 Bushing 65 Spring washer 93 Roller for chassis 66 Hex screw M 30 9 Washing 67 Screw M0 5 6 95 Bushing OPERATION INSTRUCTION ENERGY SERVICE-FREE LEAD ACID STORAGE BATTERY. Storage and Transportation Uncharged ENERGY storage battery needs no maintenance,please store it in dry and frostless place. If the density of electrolyte in filled battery is less than.3kg/l,it shall be recharged as soon as possible,if the density of electrolyte filled in is.3kg/l,the storage battery shall be recharged when it is below.8kg/l. During transportation or storage,the filled storage battery shall be kept upright vertically to prevent acid liquid from overflowing. Cover opening short circuit sliding and other damage shall be avoided in the course of transportation. 68 Front wheel 96 Pin axle 69 Nut M0 6 97 Pin axle for chassis 70 Front wheel 98 Pin axle for chassis 7 Chassis 99 Pin axle for table 7 Screw M6x8 00 Bushing 73 Table 0 Screw M6 6 7 Roller for table 0 Cable 75 Bushing 03 Cable velcro strap 76 Retaining ring for axle 0 6. PUT INTO USE Precharged but unfilled ENERGY storage battery can be put into use at once without charging after electrolyte is filled in it. When it is being filled,the temperature of battery and electrolyte should be 0 at least. Each unit of battery shall be filled with special acid whose density is.8kg/l.(.3kg/l in the area of tropics), and be filled up to the line indicating the maximum level or to the height of 5mm over the top of pole plate. Refill proper electrolyte if necessary. Screw or press the sealing hole tightly. Clean the acid liquid left on its surface. The storage battery can be in good condition without any service within 5 years at the temperature of 0. NOTE: If the output of the battery is not enough due to temperature or storage,please recharge the storage battery. 3. CHARGING Before recharging,please take the battery down. The storage battery is allowed to be charged with DC power,connect the plus pole and minus pole of storage battery correspondingly to the poles of the charger. Ensure to connect the poles rightly,switch on the charger. When the battery be charged sufficiently,cut off the charger. Recommended charging current is /0 of battery capacity(e.g./0 =.A for the storage battery with capacity of Ah.) In the course of charging,the temperature of electrolyte is not allowed to be above55. If the temperature of electrolyte is above 55,stop charging. If the density of electrolyte and the voltage of the battery stop increasing for hours,the storage battery could be thought to be charged sufficiently. When the charging is ended,please check the level of electrolyte,add pure water to the maximum level indicating line if necessary.. Maintenance To ensure the service life of storage battery,the following points must be followed. 3
WARNING AND SAFETY SIGN Follow instruction described in plate of battery,operating instruction and instruction of vehicles and ships. Wear guard-glasses. Keep children from touching electrolyte and battery. Explosive Hazard Easy-explosive mixture come to escape during charge,so fire electric spark, uncovered bulb and fireworks are strictly inhibited,when connecting wire-circuit,electric spark and short-circuit must be avoided. Hazard of strong corrosion Electrolyte is strongly corrosive,so please wear protective clothes and guard glasses,do not tilt the storage battery otherwise acid liquid will overflow. Emergency Cure when the acid liquid spatters in the eyes,wash it with a large quantity of clean water at once,then see a doctor,acid liquid on skin and clothes shall be washed with a large quantity of clean water as well,if acid liquid is swallowed,please see a doctor at once. Warning: Do not put the unprotected storage battery in the sun. Because discharged storage battery may be frozen,please store it in frostless conditions. Handling: Store discarded battery in stipulated site. Follow rules of transportation(ggvs)during transporting. Do not mix discarded battery with daily rubbish.