CX36B COMPACT EXCAVATOR TIER 4 INTERIM CERTIFIED ENGINE Model Yanmar 3TNV88-BPYB Tier 4 Interim Certified Cylinders 3 Bore/Stroke 3.46 x 3.54 in (88 x 90 mm) Displacement 100 in 3 (1.6 L) Fuel injection Direct Fuel injection pump Mechanical Fuel Diesel Fuel filter Full flow Cooling Liquid Net horsepower @ 2400 RPM SAE J1349: 28.4 hp (21.2 kw) Net maximum torque @ 1440 RPM: 72.6 lb ft (98.4 N m) POWERTRAIN Travel speeds: Forward/Reverse Low 1.6 mph (2.6 kph) High 2.8 mph (4.5 kph) Gradeability 58% (30 ) Drawbar pull 8,655 lb (38 kn) ELECTRICAL Voltage Alternator rating Battery 12 Volts 24 amp 12-volt low-maintenance OPERATOR ENVIRONMENT ROPS/FOPS three post canopy; Pilot operated hand controls and foot pedals; Adjustable seat w/ seat belt; Arm rests. Display includes: Engine oil pressure; Water temperature lamp; Air filter lamp; Water separator detection lamp; Low fuel warning lamp; Battery charge lamp; Glow plug indicator lamp; Water temperature gauge; Fuel gauge and hourmeter. OPERATING WEIGHT Operating weight 7,958 lb (3610 kg) w/ operator/full fuel/standard equipment HYDRAULICS Main pumps Tandem variable displacement/ axial piston pump Max. rated flow 2 x 10.1 gpm (2 x 38.4 L/min) Auxiliary flow 15.5 gpm (59.0 L/min) System relief pressure: Standard 3,336 psi (230 bar) Pilot control hydraulic system: Pump Gear pump Maximum capacity 3.2 gpm (12.2 L/min) Relief pressure 514 psi (35.4 bar) Control valves 10 spool Pilot control for left/right track travel, boom, arm, bucket and swing. Manual control for breaker and backfill blade. Swing/Dozer blade: Motor Travel: Motors 2 Final drive Fixed displacement axial piston Two-speed axial piston Planetary gear reduction Boom cylinder One (1) Bore diameter 3.15 in (80 mm) Rod diameter 1.97 in (50 mm) Stroke 22.7 in (578 mm) Arm cylinders Two (2) Bore diameter 3.15 in (80 mm) Rod diameter 1.77 in (45 mm) Stroke 22.05 in (560 mm) Bucket cylinder One (1) Bore diameter 2.56 in (65 mm) Rod diameter 1.38 in (35 mm) Stroke 19.6 in (497 mm) SERVICE CAPACITY Fuel tank 10 gal (38 L) Hydraulic tank: Refill capacity 10 gal (38 L) Total system 12.7 gal (48 L) Engine w/ filter change 1.8 gal (6.7 L) Radiator 1.2 gal (4.6 L) OTHER SPECIFICATIONS Swing speed 0 8.9 RPM Swing brake Spring applied, hydraulically released w/ dual cushion relief Undercarriage: Top tracks each 1 roller Bottom tracks each 4 rollers Boom: Swing 70 left/60 right Length 8 ft 2 in (2.49 m) Boom w/ arm cylinder and plumbing 485 lb (220 kg) Arm: Length 4 ft 4 in (1.32 m) Bare arm 165 lb (75 kg) Bucket cylinder linkage and plumbing 111 lb (50.3 kg) Total weight 276 lb (125.3 kg) Page 1 of 5
LIFT CAPACITIES Canopy model 4 ft 4 in (1.32 m) Arm Lift capacities calculated using 11.8 in (300 mm) shoes, 196 lb (89 kg) bucket, blade down. Load (Lift Point) Height +10 ft (3.0 m) 5 ft (1.5 m) 7.5 ft (2.3 m) 10 ft (3.0 m) END SIDE END SIDE END SIDE END SIDE END SIDE 1,190 lb (540 kg) 12.5 ft (3.8 m) 1,120 lb (510 kg) 15 ft (4.6 m) +7.5 ft (2.3 m) 1,380 lb (620 kg) 1,380 lb (620 kg) 1,280 lb (580 kg) 1,100 lb (500 kg) +5 ft (1.52 m) 2,760 lb (1250 kg) 2,380 lb (1080 kg) 1,830 lb (830 kg) 1,510 lb (680 kg) 1,480 lb (670 kg) 1,050 lb (470 kg) +2.5 ft (0.8 m) 3,760 lb (1700 kg) 2,180 lb (990 kg) 2,270 lb (1030 kg) 1,420 lb (640 kg) 1,690 lb (760 kg) 1,000 lb (450 kg) 1,390 lb (630 kg) 750 lb (340 kg) Ground Level 2,550 lb (1150 kg) 2,550 lb (1150 kg) 4,020 lb (1820 kg) 2,120 lb (960 kg) 2,520 lb (1140 kg) 1,360 lb (610 kg) 1,820 lb (820 kg) 970 lb (440 kg) -2.5 ft (-0.8 m) 4,080 lb (1850 kg) 4,080 lb (1850 kg) 3,830 lb (1740 kg) 2,120 lb (960 kg) 2,520 lb (1140 kg) 1,340 lb (610 kg) 1,800 lb (810 kg) 960 lb (430 kg) -5 ft (-1.52 m) 5,790 lb (2620 kg) 4,550 lb (2060 kg) 3,290 lb (1490 kg) 2,150 lb (970 kg) 2,210 lb (1000 kg) 1,360 lb (620 kg) -7.5 ft (-2.3 m) 3,470 lb (1570 kg) 3,470 lb (1570 kg) 2,110 lb (950 kg) 2,110 lb (950 kg) *Rated loads are hydraulic limits rather than tipping load limits. Cab model 4 ft 4 in (1.32 m) Arm Lift capacities calculated using 11.8 in (300 mm) shoes, 196 lb (89 kg) bucket, blade down. Load (Lift Point) Height +10 ft (3.0 m) 5 ft (1.5 m) 7.5 ft (2.3 m) 10 ft (3.0 m) END SIDE END SIDE END SIDE END SIDE END SIDE 1,190 lb (540 kg) 12.5 ft (3.8 m) 1,190 lb (540 kg) 15 ft (4.6 m) +7.5 ft (2.3 m) 1,280 lb (580 kg) 1,160 lb (530 kg) +5 ft (1.52 m) 2,760 lb (1250 kg) 2,510 lb (1140 kg) 1,830 lb (830 kg) 1,600 lb (720 kg) 1,480 lb (670 kg) 1,120 lb (500 kg) +2.5 ft (0.8 m) 3,760 lb (1700 kg) 2,310 lb (1050 kg) 2,270 lb (1030 kg) 1,500 lb (680 kg) 1,690 lb (760 kg) 1,070 lb (480 kg) 1,390 lb (630 kg) 800 lb (360 kg) Ground Level 2,550 lb (1150 kg) 2,550 lb (1150 kg) 4,020 lb (1820 kg) 2,250 lb (1020 kg) 2,520 lb (1140 kg) 1,450 lb (660 kg) 1,820 lb (820 kg) 1,040 lb (470 kg) -2.5 ft (-0.8 m) 4,080 lb (1850 kg) 4,080 lb (1850 kg) 3,830 lb (1740 kg) 2,250 lb (1020 kg) 2,520 lb (1140 kg) 1,430 lb (650 kg) 1,800 lb (810 kg) 1,030 lb (460 kg) -5 ft (-1.52 m) 5,790 lb (2620 kg) 4,800 lb (2180 kg) 3,290 lb (1490 kg) 2,280 lb (1030 kg) 2,210 lb (1000 kg) 1,450 lb (660 kg) -7.5 ft (-2.3 m) 3,470 lb (1570 kg) 3,470 lb (1570 kg) 2,110 lb (950 kg) 2,110 lb (950 kg) *Rated loads are hydraulic limits rather than tipping load limits. Canopy model 5 ft 3 in (1.59 m) Arm Lift capacities calculated using 11.8 in (300 mm) shoes, 196 lb (89 kg) bucket, blade down. Load (Lift Point) Height +10 ft (3.0 m) 5 ft (1.5 m) 7.5 ft (2.3 m) 10 ft (3.0 m) END SIDE END SIDE END SIDE END SIDE END SIDE 1,110 lb* (450 kg)* 12.5 ft (3.8 m) 1,010 lb* (450 kg)* 15 ft (4.6 m) +7.5 ft (2.3 m) 1,140 lb* (510 kg)* 1,140 lb* (510 kg)* 1,120 lb* (510 kg)* 1,100 lb (500 kg) 1,120 lb* (510 kg)* 780 lb (350 kg) +5 ft (1.52 m) 2,260 lb* (1020 kg)* 2,260 lb* (1020 kg)* 1,600 lb* (720 kg)* 1,520 lb* (690 kg)* 1,340 lb* (600 kg)* 1,050 lb (470 kg) 1,210 lb* (540 kg)* 760 lb (340 kg) +2.5 ft (0.8 m) 3,430 lb* (1550 kg)* 2,210 lb (1000 kg) 2,090 lb* (950 kg)* 1,420 lb (640 kg) 1,570 lb* (710 kg)* 1,000 lb (450 kg) 1,310 lb* (590 kg)* 730 lb (330 kg) Ground Level 2,310 lb* (1040 kg)* 2,310 lb* (1040 kg)* 3,930 lb* (1780 kg)* 2,100 lb (950 kg) 2,420 lb* (1100 kg)* 1,350 lb (610 kg) 1,750 lb* (790 kg)* 950 lb (430 kg) 1,380 lb* (630 kg)* 710 lb (320 kg) -2.5 ft (-0.8 m) 3,540 lb* (1600 kg)* 3,540 lb* (1600 kg)* 3,910 lb* (1770 kg)* 2,080 lb (940 kg) 2,510 lb* (1140 kg)* 1,320 lb (590 kg) 1,800 lb* (810 kg)* 930 lb (420 kg) -5 ft (-1.52 m) 4,990 lb* (2260 kg)* 4,440 lb (2010 kg) 3,520 lb* (1590 kg)* 2,100 lb (950 kg) 2,330 lb* (1050 kg)* 1,320 lb (600 kg) 1,620 lb (730 kg) 940 lb (430 kg) -7.5 ft (-2.3 m) 4,610 lb* (2090 kg)* 4,580 lb (2070 kg) 2,620 lb* (1180 kg)* 2,170 lb (980 kg) *Rated loads are hydraulic limits rather than tipping load limits. CX36B Page 2 of 5
B C K A L H J G D E F Line drawings are for illustrative purpose only and may not be exact representation of unit. DIMENSIONS A. Overall height 8 ft 5 in (2.57 m) B. Overall length 15 ft 5 in (4.71 m) C. Width of upperstructure 5 ft 1 in (1.55 m) D. Track overall length 7 ft 1 in (2.15 m) E. Track overall width with 11.8 in (300 mm) shoes 5 ft 7 in (1.70 m) F. Track shoe width 11.8 in (300 mm) G. Center to center idler to sprocket 5 ft 7 in (1.70 m) H. Upperstructure ground clearance 1 ft 10 in (570 mm) J. Minimum ground clearance 12.9 in (330 mm) K. Tail swing radius 2 ft 9 in (850 mm) L. Backfill blade height 1 ft 1 in (345 mm) Working weight 7,958 lb (3610 kg) Ground pressure 4.6 psi (32 kpa) Boom swing Left 70 /Right 60 Tail swing overhang 0 ft 0 in (0 m) CX36B Page 3 of 5
M N S R Q T P Line drawings are for illustrative purpose only and may not be exact representation of unit. PERFORMANCE SPECS 5 ft 3 in (1.59 m) Arm 4 ft 4 in (1.32 m) Arm M. Maximum dig radius 18 ft 0 in (5.50 m) 17 ft 2 in (5.24 m) N. Dig radius at groundline 17 ft 7 in (5.37 m) 16 ft 8 in (5.11 m) P. Maximum dig depth 11 ft 0 in (3.35 m) 10 ft 1 in (3.07 m) Q. Dump height 12 ft 4 in (3.76 m) 11 ft 8 in (3.58 m) R. Overall reach height 16 ft 11 in (5.16 m) 16 ft 3 in (4.98 m) S. Bucket rotation 178 178 T. Vertical straight wall dig depth 8 ft 8 in (2.65 m) 7 ft 10 in (2.39 m) Arm digging force 3,731 lb (17 kn) 4,203 lb (19 kn) Bucket digging force: 2 position bucket 8,430 lb (37 kn) 8,430 lb (37 kn) CX36B Page 4 of 5
STANDARD EQUIPMENT OPERATOR ENVIRONMENT See page 1 ENGINE Yanmar 3TNV88-BPYB diesel 4 Cycle Water cooled Direct injection One touch decelerator Engine access under rear hood Dry type air cleaner with restriction indicator Glow plug starting aid ELECTRICAL 12-volt electrical starting system Heavy-duty battery Horn HYDRAULICS Auxiliary hydraulics single/bi-directional and plumbing to arm Large hydraulic oil cooler Control pattern selector valve TRACK DRIVE Rubber tracks Automatic 2-speed travel Fully hydrostatic drive system Sealed and lubricated track rollers Track tension adjustment grease type Disc type parking brake auto release and apply UPPER STRUCTURE Zero tail swing Swing lock Swing brake Swing shock valve OTHER Swing boom 70 left/60 right Hydraulic backfill blade OPTIONAL EQUIPMENT OPERATOR ENVIRONMENT Cab enclosure with heater OTHER Steel tracks 5 ft 3 in (1.59 m) arm Mechanical coupler Rigid thumb Rigid thumb-coupler BUCKETS Width SAE Heaped Capacity Weight 12 in (305 mm) 2.13 ft 3 (0.060 m 3 ) 155 lb (70 kg) 24 in (610 mm) 4.25 ft 3 (0.120 m 3 ) 218 lb (99 kg) 36 in (914 mm) 6.60 ft 3 (0.186 m 3 ) 290 lb (132 kg) NOTE: All specifications are stated in accordance with SAE Standards or Recommended Practices, where applicable. NOTE: All engines meet current EPA emissions requirements. IMPORTANT: Case Construction Equipment Inc. reserves the right to change these specifications without notice and without incurring any obligation relating to such change. Case Construction Equipment Inc. does not warrant the safety or reliability of attachments from other manufacturers. Case is a registered trademark of CNH America LLC. Any trademarks referred to herein, in association with goods and/or services of companies other than CNH America LLC, are the property of those respective companies. www.casece.com Form No. CCE201212CX36B Printed in U.S.A. 2012 CNH America LLC Replaces form no. CCE5010801 CX36B Page 5 of 5 All Rights Reserved All Case construction equipment is biodiesel ready.
CX B SERIES COMPACT EXCAVATORS CX17B CX27B CX31B CX36B CX55B
MINI EXCAVATORS. MANY ADVANTAGES. Whether you re a small business or a general contractor needing impressive power within a small space, the full line of CASE compact excavators offer all the features and functionality needed to handle the toughest jobs in the tightest places. Four Tier 4 Interim models and the Tier 4 Final CX55B deliver breakout forces from 3,417 to 11,028 lbs. and digging depths up to nearly 13 feet. And it s all powered by high-efficiency hydraulics that maximize performance, and precision controls that instantly feel familiar. Experience the big-time benefits of the CX B Series. Zero Tail Swing* *Excludes CX55B Center-Swing Boom Control Integrated-Flow Pump System Exclusive In-Frame Sliding Door* *Excludes CX55B 2
Models Available CX17B CX27B CX31B CX36B Three-Post ROPS Design Automatic* Two-Speed Travel *Manual two-speed travel on CX17B and CX27B CX55B 3
IT HOLDS NOTHING BACK. IN THE CLEAR WITH ZERO TAIL SWING* CASE compact excavators offer a true, zero-radius tail swing that keeps the sides and back of the machine within the width of the tracks when rotating even with the door open. You can dig and dump 180, right against obstacles, without a problem and with less risk of damaging the machine or worksite. *Excludes CX55B FOOT PEDAL CENTER-SWING BOOM CONTROL A foot-controlled boom swing allows for simultaneous operation of the house and boom. Coupled with a center-swing design that angles the boom up to 80 left and 65 right, operators are able to dig and use attachments around trees and parallel with foundations, fences, walls or whatever s on the worksite. INTEGRATED-FLOW PUMP SYSTEM: SMART POWER PLACEMENT This innovative system helps improve fuel efficiency and maximize strength by directing hydraulic power to where you need it, when you need it. With dozing, flow is focused on the tracks and blade. When swinging or raising the arm, pump power is diverted to the boom. During digging, all flow is pumped to the bucket and arm. FASTER CYCLE TIMES WITH TWO-SPEED TRAVEL Automatic on the CX31B, CX36B and CX55B, and push-button activated on the CX17B and CX27B, the two-speed travel drive function matches speed and performance to jobsite conditions. All models also include one-touch engine deceleration to quickly cut engine RPMs for greater fuel savings and reduced noise levels. RETRACTABLE TRACKS Getting through backyard gates or any tight spot is easy for the CX17B, thanks to tracks that hydraulically retract from 52 inches to a narrow 39-inch width. And all our compact excavators come standard with durable rubber tracks with big, deep nubs for greater grip. CASE even offers steel tracks on every model for heavy-duty applications. 4
My two CASE compact excavators just shine. We have had zero problems. Benoit Drainage 5
3-POST CANOPY*. 360 VISIBILITY. Our ROPS-certified three-post canopy design creates a wideopen entry area for easier access in and out of the operating platform. And as an added benefit, the absence of a fourth post provides greater visibility of the attachment and around the machine. *CX55B features a four-post ROPS/ FOPS-certified canopy. 6
GET A LITTLE MORE COMFORTABLE. SMARTEST CAB DOOR IN ITS CLASS What s the point of a zero tail swing design if the open door hangs over the tracks? CASE compact excavators* come standard with a cab door that slides all the way open within the machine frame, keeping it securely out of the way. *Excludes CX55B Exclusive sliding cab door maintains zero tail swing. PRECISION CONTROLS COME STANDARD All CASE compact excavators even our smallest models come standard with hydraulic pilot controls for comfortable, highly responsive operation. On top of that, all models also feature a pattern control selector valve that lets you easily toggle between ISO and SAE patterns to meet operator preference. Proportional auxiliary hydraulics joystick with thumb toggle puts precision at your fingertips. CONSTRUCTED FOR COMFORT With an adjustable seat and standard arm rest, as well as an optional heating and A/C system* for our enclosed cabs, the spacious operating platforms of the CX B Series help keep you comfortable all day long and all year round. *HVAC system only available on the CX31B and larger. Spacious CX55B cab offers an optional LCD display. 7
COMPACT CLASS, MID-SIZE MUSCLE. CX55B The CX55B pushes the envelope of what it means to be a mini-excavator. It features best-in-class power, a wider operating range and a cab design that offers plenty of room and superior visibility all while maintaining minimum tail swing and an overall cab height of only 8-feet 4-inches. It s perfect for when you need a lot of strength in a little package. 8
7.5-INCH MINIMAL TAIL SWING Minimal tail overhang allows for excellent maneuverability in tight areas. ECO MODE Achieve 25% less fuel consumption at the push of a button (compared to previous generation). indr COOLING SYSTEM A revolutionary Integrated Noise and Dust Reduction (indr) filter removes dust before cooling components to maximize cooling efficiency and reduce cleaning intervals. It also delivers amazingly quiet operation. DOZER-STYLE BLADE A new, one-pass backfill blade design forms material into an arc that always falls forward. LCD MONITOR An optional LCD monitor makes performance data and machine diagnostics readily available. 9
MAINTENANCE MADE EASY. SERVICEABILITY IS IN OUR DNA When you invest in CASE equipment, you need it to last. We make it simple. CASE compact excavators are no exception. From wide-open, swing-out access panels to ground-level site gauges and service points, you can do daily maintenance in a matter of minutes. It s the easiest way to help you get the most performance and longest life out of your machine. Update Livery EASY ACCESS TO EVERYTHING 10 1. Air filter 2. Water separator 3. Fuel filter 4. Hydraulic oil fill 5. Radiator 6. Grouped hydraulic hoses 7. Hydraulic site gauge 8. Hour meter 9. ISO/SAE pattern changer 10. Single/bi-directional select 11. Lockable fuel cap 12. Engine oil fill 13. Engine oil filter 14. Fuel drain 15. Coolant reservoir
SUPPORT COMES STANDARD Base & Extended Warranty Coverage* 1-Year/1,000-Hour Full-Coverage Limited Base Warranty. * Please see your CASE dealer for limitations, exclusions and confirmation of policies in effect. Purchased Protection Plan Extension of the factory base and extended coverage is available at an additional cost. Plans are available up to three years/3,000 hours on CASE compact excavators. Talk to your CASE dealer to determine the plan that best fits your needs. Breakdown Assistance Standard on all CASE equipment. NO TOOLS NEEDED The CX B Series continues the CASE hallmark of simple serviceability with features like tool-free access to routine maintenance points. STRONGER PRODUCT SUPPORT SOLUTIONS Your CASE dealer knows best how you can maximize your equipment investment and uptime, with genuine CASE parts, expert service and a complete range of product support solutions including CASE remanufactured and all-makes parts. CASE supports better parts availability and faster deliveries, through nine parts distribution centers in North America and a forecasting system to ensure that the right parts will be there when you need them. And only CASE dealers have exclusive access to the Electronic Service Tool that quickly pinpoints machine issues to help maximize uptime. 11
AUXILIARY EXCELLENCE Auxiliary hydraulics come standard with lines plumbed all the way down the arm for easy hook-up. 12
ATTACHMENTS GALORE. BUCKETS AND MUCH MORE There s a full range of attachments, including a full line of CASE buckets with a wide range of sizes and digging forces. INDUSTRY-EXCLUSIVE BLADE DESIGN CASE dozer blades feature an increased 38 approach angle and a unique shape that efficiently rolls dirt as it pushes, leaving a smooth and level surface. And with the optional 4-way blade*, operators can raise and lower the blade for added stability and improved backfilling or grading. *4-way angle blade available on the CX31B and larger SMARTFIT BUCKET TEETH CASE compact excavator buckets come standard with the innovative SmartFit bucket tooth system. These heavy-duty, self-sharpening teeth combine exceptional strength and unmatched ease of installation, thanks to a hammerless fastener system with reusable locking pins. Available in a full range of styles. 13
THE CX B SERIES COMPACT EXCAVATORS SPECIFICATIONS CX17B CX27B CX31B CX36B CX55B Tier 4 Final Engine Mitsubishi L3E-W231KBS Yanmar 3TNV82-A-SYB Yanmar 3TNV88-BPYB Yanmar 3TNV88-BPYB Yanmar 4TNV88-C-PYB Net hp (kw) 15.2 (11.3) @ 2200 RPM 21.3 (15.9) @ 2200 RPM 28.4 (21.2) @ 2400 RPM 28.4 (21.2) @ 2400 RPM 39.3 (29.3) @ 2400 RPM Emissions certification* Tier 4 Interim Tier 4 Interim Tier 4 Interim Tier 4 Interim Tier 4 Final (CEGR/DPF) Bucket digging force lb. (kn) 3,417 (15.2) 6,351 (28.2) 8,430 (37.5) 8,430 (37.5) 11,128 (49.5) Arm digging force lb. (kn) 1,956 (8.7) 2,877 (12.8) 3,373 (15.0) 3,731 (17.0) 5,300 (23.7) Operating weight lb. (kg) 3,638 (1 650) 5,556 (2 520) 6,679 (3 030) 7,958 (3 610) 11,310 (5 130) DIMENSIONS Overall height 7 ft. 9 in. (2.35 m) 8 ft. 2 in. (2.50 m) 8 ft. 5 in. (2.57 m) 8 ft. 5 in. (2.57 m) 8 ft. 4 in. (2.55 m) Overall length 11 ft. 3 in. (3.42 m) 13 ft. 11 in. (4.13 m) 14 ft. 4 in. (4.39 m) 15 ft. 5 in. (4.71 m) 17 ft. 10 in. (5.42 m) Width of upperstructure 2 ft. 11 in. (0.89 m) 4 ft. 7 in. (1.40 m) 5 ft. 1 in. (1.55 m) 5 ft. 1 in. (1.55 m) 6 ft. 4 in. (1.94 m) Track overall length 5 ft. 2 in. (1.56 m) 6 ft. 6 in. (1.98 m) 6 ft. 7 in. (2.00 m) 7 ft. 1 in. (2.15 m) 8 ft. 1 in. (2.48 m) Track overall width with shoes** 4 ft. 4 in. (1.32 m) 4 ft. 11 in. (1.50 m) 5 ft. 1 in. (1.55 m) 5 ft. 7 in. (1.70 m) 6 ft. 6 in. (1.98 m) Track shoe width 9.1 in. (230 mm) 9.8 in. (250 mm) 11.8 in. (300 mm) 11.8 in. (300 mm) 15.7 in. (400 mm) Upperstructure ground clearance 18.0 in. (445 mm) 20.0 in. (520 mm) 22.0 in. (570 mm) 22.0 in. (570 mm) 24.5 in. (625 mm) Minimum ground clearance 6.9 in. (175 mm) 9.8 in. (250 mm) 12.9 in. (330 mm) 12.9 in. (330 mm) 14.0 in. (350 mm) Rear tail swing radius 2 ft. 2 in. (0.66 m) 2 ft. 5 in. (0.75 m) 2 ft. 7 in. (0.79 m) 2 ft. 9 in. (0.85 m) 4 ft. 2 in. (1.28 m) Digging depth 7 ft. 1 in. (2 159 mm) 8 ft. 4 in. (2 540 mm) 9 ft. 2 in. (2 794 mm) 10 ft. 1 in. (3 073 m) 12 ft. 10 in. (3 912 mm) NOTE: *CEGR = Cooled Exhaust Gas Recirculation; DPF = Diesel Particulate Filter. **Measurements taken using standard equipment. 14
BUILDING A STRONG CASE Already in high gear with the arrival of founder J.I. Case s portable steam engine in 1869, we found ourselves at the heart of the road construction boom of the early 1900s. The path was set. Today, CASE is a game changer in construction equipment, financing, parts and service. Revolutionary is nothing new to CASE, as innovations like the integrated loader/backhoe (1957), Ride Control, over-center boom design and ProCare have shown. It s this ingenuity and spirit that fuels our ongoing pursuit of building industry-leading performance and productivity into every machine throughout our full line of light, medium and heavy equipment. All of this is backed by a portfolio of more than 10,000 OEM, REMAN and Gold Value parts, more than 350 North American dealer locations, and unmatched financial and insurance services that ensure the best support is always within reach. When all is said and done, our strength is only as solid as the machines we engineer, the support and service we give, and most importantly, the vote of confidence CASE customers have with every bit of it. Specialized finance programs and flexible leasing packages put you in the driver s seat of industryleading CASE equipment, while no-nonsense warranties and comprehensive protection plans ensure that your equipment is protected. As the only finance company dedicated to CASE, we offer strong products and services designed around your unique needs and are the only ones supported by the helpful service professionals at your CASE dealer. To learn more about CASE or for attentive customer service, visit your nearest dealer, call 1-866-54CASE6 or visit us online at CaseCE.com. 15
CaseCE.com 2014 CNH Industrial America LLC. All rights reserved. CASE is a trademark registered in the United States and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates. CNH Industrial Capital is a trademark in the United States and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates. Printed in U.S.A. Form No. CCE201401CEXC Always read the Operator s Manual before operating any equipment. Inspect equipment before using it, and be sure it is operating properly. Follow the product safety signs and use any safety features provided. NOTE: All engines meet current EPA emission regulations. NOTE: All specifications are stated in accordance with SAE Standards or Recommended Practices, where applicable. Contains 10% post-consumer fiber IMPORTANT: CASE Construction Equipment Inc. reserves the right to change these specifications without notice and without incurring any obligation relating to such change. Availability of some models and equipment builds vary according to the country in which the equipment is used. The illustrations and text may include optional equipment and accessories and may not include all standard equipment. Your CASE dealer/distributor will be able to give you details of the products and their specifications available in your area. CASE Construction Equipment is biodiesel friendly.