INSTALL GUIDE DOCUMENT NUMBER 5506 REVISION DATE 08098 FIRMWARE OEM-AL(RS)-NI9-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
VEHICLE LIST - OF PAGE OF 9 DOC.: #5506 08098 FEATURES MAKE MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS SECURE TAKEOVER PARKING LIGHT CTRL X LOCK REMOTE START ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK RAP SHUTDOWN CTRL DOOR STATUS MONITORING TRUNK STATUS MONITORING NISSAN BRAKE PEDAL STATUS MONITORING TACHOMETER STATUS MONITORING HORN CTRL Qashqai STD Key AT 7 Rogue STD Key AT -6 Rogue STD Key AT 7 Rogue STD Key AT 8 Rogue Sport STD Key AT 7
BOX CONTENTS - OF PAGE OF 9 DOC.: #5506 08098 BOX CONTENTS MODULE 6 PIN WHITE PIN BLACK WHITE 5 6 PROGRAMMING BUTTON LED 7 PIN WHITE 0 PIN BLACK WHITE WHITE 5 6 7 M M M M6 0 9 8 7 6 5 BLACK PIN WHITE DATA CABLE BLUE M M5 BLACK DATA PORT (WEBLINK, RF, TELEMATIC) PIN BLUE DATA CABLE WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT PIN BLACK CABLE
COMPONENT LOCATOR - OF PAGE OF 9 DOC.: #5506 08098 INTERIOR VIEW A B DRIVER SIDE VIEW PASSENGER SIDE VIEW
TYPE - WIRE CHART - OF PAGE 5 OF 9 DOC.: #5506 08098 MAKE MODEL YEAR NISSAN WIRE DESCRIPTION NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR CanH OBDII White 6 pin 06 Blue (DATA) At OBDII connector B CanL OBDII White 6 pin Pink (DATA) At OBDII connector B Negative Ignition M8 Gray 0 pin 7 Yellow (-) At BCM A Negative Ignition M8 Gray 0 pin 8 LtPurple/White or Green/White (-) At BCM A Negative Ignition M8 Gray 0 pin 5 Brown (-) At BCM A Rogue STD key AT -6 Ignition OBDII White 6 pin 08 Yellow (+) At OBDII connector B V OBDII White 6 pin 6 White (+) At OBDII connector B Unlock M9 Black 0 pin Pink (-) At BCM A Lock M9 Black 0 pin Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 6 pin 0 Black (-) At OBDII connector B Negative Starter E9 Black pin 9 Green (-) At BCM A Hazard Light M8 Gray 0 pin Yellow (-) At BCM A
TYPE - WIRING DIAGRAM - OF PAGE 6 OF 9 DOC.: #5506 08098 OBDII (UNDER DRIVER SIDE DASH) M M M M M6 M5 DATA M 0 GRAY/YELLOW (NC) 0 GRAY/RED - LOCK (-) OUTPUT 0 GREEN/YELLOW (NC) 0 GREEN/RED - UNLOCK (-) OUTPUT 05 BLUE/YELLOW - STARTER (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT 5A IGNITION (+) - 08 CANL - CANH - 06 GROUND (-) - 0 V (+) - 6 5 6 7 8 9 : E9 BLACK 0 5 6 BCM (LEFT OF STEERING COLUMN) M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE (NC) 0 ORANGE/WHITE - TRUNK (-) OUTPUT 05 ORANGE/BLACK (NC) 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH M 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) STARTER (-) - 9 CONNECT ONLY WHENUSING A COMPATIBLE ACCESSORY LOCK/ARM (-) - UNLOCK/DISARM (-) - 0 9 8 7 6 5 0 9 8 7 6 5 : M9 BLACK 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 M 0 WHITE - GROUND (-) INPUT 0 WHITE/RED (NC) 0 WHITE/BLACK - IGNITION (-) OUTPUT M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 0 RED - V (+) M5 DATA CABLE M6 0 GREEN/BLACK - HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) COMPATIBLE ACCESSORY WITHOUT A COMPATIBLE ACCESSORY OR WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. IGNITION (-) - 5 IGNITION (-) - 7 IGNITION (-) - 8 HAZARD LIGHT (-) - POWER LIFTGATE (-) - 06 : M8 GRAY 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 GREEN 8 7 6 5 POWER LIFTGATE SWITCH OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
TYPE - WIRE CHART - OF PAGE 7 OF 9 DOC.: #5506 08098 MAKE MODEL YEAR WIRE DESCRIPTION NAME COLOR TYPE NISSAN POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR Qashqai STD Key AT Rogue STD Key AT 7 7 CanH ~ Green 0 pin 0 Blue (DATA) At BCM A CanL ~ Green 0 pin 0 Pink (DATA) At BCM A Negative Ignition M8 Gray 0 pin 7 LtPurple/LtGreen (-) At BCM A Negative Ignition M8 Gray 0 pin 8 LtPurple/Blue (-) At BCM A Negative Ignition M8 Gray 0 pin 5 LtPurple/Pink (-) At BCM A Ignition OBDII White 6 pin 08 Yellow (+) At OBDII connector B V OBDII White 6 pin 6 White (+) At OBDII connector B Unlock M9 Black 0 pin Pink (-) At BCM A Lock M9 Black 0 pin Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 6 pin 0 Black (-) At OBDII connector B Negative Starter E9 Black pin 9 Blue (-) At BCM A Hazard Light M8 Gray 0 pin LtPurple/Yellow (-) At BCM A CanH ~ Green 0 pin 0 Blue (DATA) At BCM A CanL ~ Green 0 pin 0 Pink (DATA) At BCM A Negative Ignition M8 Gray 0 pin 7 Yellow (-) At BCM A Negative Ignition M8 Gray 0 pin 8 LtPurple/White or Green/White (-) At BCM A Negative Ignition M8 Gray 0 pin 5 Brown (-) At BCM A Ignition OBDII White 6 pin 08 Yellow (+) At OBDII connector B V OBDII White 6 pin 6 White (+) At OBDII connector B Unlock M9 Black 0 pin Pink (-) At BCM A Lock M9 Black 0 pin Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 6 pin 0 Black (-) At OBDII connector B Negative Starter E9 Black pin 9 Green (-) At BCM A Hazard Light M8 Gray 0 pin Yellow (-) At BCM A
TYPE - WIRE CHART - OF PAGE 8 OF 9 DOC.: #5506 08098 MAKE MODEL YEAR NISSAN WIRE DESCRIPTION NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR CanH ~ Green 0 pin 0 Blue (DATA) At BCM A CanL ~ Green 0 pin 0 Pink (DATA) At BCM A Negative Ignition M8 Gray 0 pin 7 LtPurple/LtGreen (-) At BCM A Negative Ignition M8 Gray 0 pin 8 LtPurple/Blue (-) At BCM A Negative Ignition M8 Gray 0 pin 5 LtPurple/Pink (-) At BCM A Rogue Sport STD Key AT 7 Ignition OBDII White 6 pin 08 Yellow (+) At OBDII connector B V OBDII White 6 pin 6 White (+) At OBDII connector B Unlock M9 Black 0 pin Pink (-) At BCM A Lock M9 Black 0 pin Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 6 pin 0 Black (-) At OBDII connector B Negative Starter E9 Black pin 9 Blue (-) At BCM A Hazard Light M8 Gray 0 pin LtPurple/Yellow (-) At BCM A
TYPE - WIRING DIAGRAM - OF PAGE 9 OF 9 DOC.: #5506 08098 OBDII (UNDER DRIVER SIDE DASH) M M M M M6 M5 DATA 5A IGNITION (+) - 08 GROUND (-) - 0 V (+) - 6 5 6 7 8 9 0 5 6 M 0 GRAY/YELLOW (NC) 0 GRAY/RED - LOCK (-) OUTPUT 0 GREEN/YELLOW (NC) 0 GREEN/RED - UNLOCK (-) OUTPUT 05 BLUE/YELLOW - STARTER (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE (NC) 0 ORANGE/WHITE - TRUNK (-) OUTPUT 05 ORANGE/BLACK (NC) 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH M 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) STARTER (-) - 9 CONNECT ONLY WHENUSING A COMPATIBLE ACCESSORY LOCK/ARM (-) - UNLOCK/DISARM (-) - : E9 BLACK 0 9 8 7 6 5 0 9 8 7 6 5 : M9 BLACK BCM (LEFT OF STEERING COLUMN) 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 5 M 0 WHITE - GROUND (-) INPUT 0 WHITE/RED (NC) 0 WHITE/BLACK - IGNITION (-) OUTPUT M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 0 RED - V (+) M5 DATA CABLE M6 0 GREEN/BLACK - HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) COMPATIBLE ACCESSORY WITHOUT A COMPATIBLE ACCESSORY OR WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. IGNITION (-) - 5 IGNITION (-) - 7 IGNITION (-) - 8 HAZARD LIGHT (-) - CANH - 0 CANL - 0 POWER LIFTGATE (-) - 06 : M8 GRAY 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 5 : GREEN 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 GREEN 8 7 6 5 POWER LIFTGATE SWITCH OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
TYPE - WIRE CHART - OF PAGE 0 OF 9 DOC.: #5506 08098 MAKE MODEL NISSAN YEAR WIRE DESCRIPTION NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR CanH ~ Green 0 pin 0 Blue (DATA) At BCM A CanL ~ Green 0 pin 0 Pink (DATA) At BCM A Negative Ignition M8 Gray 0 pin 7 Yellow (-) At BCM A Negative Ignition M8 Gray 0 pin 8 LtPurple/White or Green/White (-) At BCM A Negative Ignition M8 Gray 0 pin 5 Brown (-) At BCM A Rogue STD Key AT 8 Ignition OBDII White 6 pin 08 Yellow (+) At OBDII connector B V OBDII White 6 pin 6 White (+) At OBDII connector B Unlock M9 Black 0 pin Pink (-) At BCM A Lock M9 Black 0 pin Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 6 pin 0 Black (-) At OBDII connector B Negative Starter E9 Black pin 9 Green (-) At BCM A Hazard Light M8 Gray 0 pin Yellow (-) At BCM A Driver Door Pin ~ Green 0 pin 7 LtBlue (-) At BCM A
TYPE - WIRING DIAGRAM - OF PAGE OF 9 DOC.: #5506 08098 OBDII (UNDER DRIVER SIDE DASH) M M M M M6 M5 DATA 5A IGNITION (+) - 08 GROUND (-) - 0 V (+) - 6 5 6 7 8 9 0 5 6 M M 0 GRAY/YELLOW (NC) 0 GRAY/RED - LOCK (-) OUTPUT 0 GREEN/YELLOW (NC) 0 GREEN/RED - UNLOCK (-) OUTPUT 05 BLUE/YELLOW - STARTER (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE (NC) 0 ORANGE/WHITE - TRUNK (-) OUTPUT 05 ORANGE/BLACK (NC) 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH STARTER (-) - 9 MANDATORY WITH OEM ALARM : E9 BLACK 0 9 8 7 6 5 0 9 8 7 6 5 BCM (LEFT OF STEERING COLUMN) 5 M 0 YELLOW - RAP SHUTDOWN (-) OUTPUT 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) LOCK/ARM (-) - UNLOCK/DISARM (-) - : M9 BLACK 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 M 0 WHITE - GROUND (-) INPUT 0 WHITE/RED (NC) 0 WHITE/BLACK - IGNITION (-) OUTPUT M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 0 RED - V (+) M5 DATA CABLE M6 0 GREEN/BLACK - HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) COMPATIBLE ACCESSORY WITHOUT A COMPATIBLE ACCESSORY OR WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. IGNITION (-) - 5 IGNITION (-) - 7 IGNITION (-) - 8 HAZARD LIGHT (-) - DRIVER DOOR PIN (-) - 7 CANH - 0 CANL - 0 POWER LIFTGATE (-) - 06 : M8 GRAY 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 5 : GREEN 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 GREEN 8 7 6 5 POWER LIFTGATE SWITCH OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
MODULE PROGRAMMING PROCEDURE - OF PAGE OF 9 DOC.: #5506 08098 0 ACC ON START Set ignition to ON position. 07 ACC ON START Set ignition to position. ACC ON START Set ignition to position. 0 Wait, LED will turn solid RED, then solid GREEN for second, then solid RED. 08 WARNING: Disconnect power last. Disconnect module from vehicle. Module Programming Procedure completed. 0 ACC ON START Set ignition to position. 09 Connect module to computer and proceed with extended programming. 0 Wait, LED will turn. 0 Connect power first. Connect module to vehicle. 05 ACC ON START Set ignition to ON position. ACC ON START Set ignition to ON position. 06 If LED flashes GREEN rapidly, proceed with step 7. If LED turns solid GREEN for seconds, proceed with step. Wait, LED will turn solid GREEN for seconds.
VALET MODE PROGRAMMING PROCEDURE - OF PAGE OF 9 DOC.: #5506 08098 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to 5. 0 Time restriction. Complete next step within 7 seconds. 0 ACC ON START Cycle ignition ON five times [5x /ON] rapidly. ENGINE START STOP 0 Wait, LED will turn solid RED for seconds. 0 ACC ON START Set ignition to position. ENGINE START STOP 05 Valet Mode Programming Procedure completed.
PAGE OF 9 MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 ACC ON START DOC.: #5506 08098 TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP 0 0 [X]
MODULE NAVIGATION CHART - OF PAGE 5 OF 9 DOC.: #5506 08098 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 DISARM/UNLOCK BEFORE START 0 0 ON 0 RELOCK AFTER START 0 0 ON 0 RELOCK AFTER SHUTDOWN 0 0 ON 0 FORCE UNLOCK ALL ON FIRST PRESS 0 0 ON 05 N/A 0 N/A 06 N/A 0 N/A 0 DISABLE 07 FACTORY KEYLESS RS SEQUENCE 0 N/A 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 0 MIN 0 CONFIGURATION 0 05 MIN 0 0 MIN 08 MODULE RUN TIME 0 5 MIN 05 5 MIN 06 0 MIN 07 5 MIN 08 5 MIN 0 0 SEC 0 05 SEC 0 08 SEC 09 WAIT TO START DELAY 0 0 SEC 05 5 SEC 06 0 SEC 07 5 SEC 08 0 SEC 0- N/A 0 N/A 0-07 Technical Support only 0 N/A 0 N/A
REMOTE STARTER ERROR CODES - OF PAGE 6 OF 9 DOC.: #5506 08098 REMOTE STARTER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Foot brake is ON. 0 Hood is open. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error.
MODULE DIAGNOSTICS - OF PAGE 7 OF 9 DOC.: #5506 08098 TEST MODULE LED STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.
MODULE RESET PROCEDURE - OF PAGE 8 OF 9 DOC.: #5506 08098 0 Disconnect all connectors from module except the BLACK -PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK -PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK -PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. 06 Module RESET completed.
INSTALLATION CHECKLIST - OF PAGE 9 OF 9 DOC.: #5506 08098 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. Exit vehicle. 5 Installation checklist completed.