INSTALL GUIDE DOCUMENT NUMBER 54560 REVISION DE 201818 FIRMWARE OL-NI(RS)-NI5-[OL-RS-NI5] HARDWARE OL-RS-NI5 ACCESSORIES OL-LOADER (REQUIRED) RF-10/30/50-EDP (OPTIONAL) LINKR (OPTIONAL) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. BEFORE INSTALLION 1- Connect module to computer 2- Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)
VEHICLE LIST - 1 OF 2 PAGE 2 OF 27 FEURES MAKE MODEL YEAR INFINITI INSTALL TYPE DA IMMOBILIZER BYPASS SECURE TAKE OVER DISARM OEM ALARM DOOR LOCK DOOR UNLOCK 3X LOCK START/STANDALONE MOD. TRUNK/HCH RELEASE DOOR STUS OUTPUT TRUNK STUS OUTPUT HOOD STUS OUTPUT** TACHOMETER OUTPUT BRAKE PEDAL STUS OUTPUT * E-BRAKE STUS OUTPUT EX35 2 EX35-12 1 EX37 13 1 FX35 2 FX35 10-12 1 FX37 13 1 FX45 2 FX50 2 FX50 10-13 1 G25 11-12 2 G35 2 G37 2 G37-13 2 Q60 Convertible 14-15 3 Q60 Coupe 14-15 3 QX50 14-16 4 QX70 14-16 4 * Available only when ignition is in the ON position. ** Available only if vehicle is equipped with factory hood switch.
VEHICLE LIST - 2 OF 2 PAGE 3 OF 27 FEURES MAKE MODEL YEAR INSTALL TYPE NISSAN DA IMMOBILIZER BYPASS SECURE TAKE OVER DISARM OEM ALARM DOOR LOCK DOOR UNLOCK 3X LOCK START/STANDALONE MOD. TRUNK/HCH RELEASE DOOR STUS OUTPUT TRUNK STUS OUTPUT HOOD STUS OUTPUT** TACHOMETER OUTPUT BRAKE PEDAL STUS OUTPUT * E-BRAKE STUS OUTPUT 370Z -16 2 Altima Coupe 1 Altima Coupe -13 1 Altima Sedan 07-1 Altima Sedan -12 1 Altima Sedan Hybrid 07-1 Altima Sedan Hybrid -13 1 GT-R -16 2 Maxima -14 2 Murano 2 Murano 10-14 1 * Available only when ignition is in the ON position. ** Available only if vehicle is equipped with factory hood switch.
BOX CONTENTS - 1 OF 1 PAGE 4 OF 27 BOX CONTENTS MODULE T-HARNESS 1 VS1 10 PIN BLUE BLACK 2 1 4 3 6 5 2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 M1 M2 LED 2 LED 1 M7 M6 M5 PROGRAMMING BUTTON 4 3 2 1 4 3 2 1 3 2 1 BLACK RF PORT/ WEBLINK PORT BLUE TELEMIC PORT BLACK MS1 MS2 VS2 VS3 VS4 VS5 VS6 12 PIN OPTIONAL TERMINALS (OEM ALARM CONTROL) BLACK 2 1 4 3 6 5 8 7 10 9 12 11 M3 M4 9 10 7 8 5 6 3 4 1 2 WHITE MS3 VS7 VS8 AFTERMARKET HOOD SWITCH AND CABLE VS9 VS10 WARNING STICKER VS11 VS12 WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE
COMPIBLE ACCESSORIES - 1 OF 1 PAGE 5 OF 27 DOC.: #54560 201818 RF KIT (accessories sold separately) OMEGA RF KIT MODULE RF PORT ANTENNA TELEMIC KIT (accessories sold separately) OLCLLINK CARLINK MODULE TELEMIC PORT TELEMIC KIT (accessories sold separately) LINKR MODULE TELEMIC PORT
TYPE 1 - CHART - 1 OF 2 PAGE 6 OF 27 INFINITI MAKE MODEL YEAR DESCRIPTION NAME TYPE POSITION POLARITY MODULE LOCION COMPONENT LOCOR NISSAN EX35 EX37 FX35 FX37 FX50 FX50 Altima Coupe Altima Coupe -12 13 10-12 13 10-12 13-10-12 Driver Door Pin M123 Green 40 pin 150 LtGreen (-) BCM, passenger kick panel ~ Parking Light B6 white 12 pin 4G Red (+) Fuse box, rear side ~ Driver Door Pin M123 Green 40 pin 150 LtGreen (-) BCM, passenger kick panel ~ Parking Light B6 white 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light B6 white 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light M2 white 10 pin 8B Red (+) Fuse box, rear side ~ Parking Light B6 white 12 pin 4G Red (+) Fuse box, rear side ~ Lock/Arm M123 Green 40 pin ZA Empty (-) BCM, passenger kick panel (use provided terminal for connection) ~ Parking Light M2 white 10 pin 8B Red (+) Fuse box ~ Lock/Arm M18 Green 40 pin 56 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M18 Green 40 pin 34 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M18 Green 40 pin 58 LtBlue (-) BCM, behind cluster ~ Parking Light B4 Brown 12 pin 4T Blue/Red (+) Fuse box, rear side ~ Lock/Arm M18 Green 40 pin 56 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M18 Green 40 pin 34 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M18 Green 40 pin 58 LtBlue (-) BCM, behind cluster ~ Parking Light B4 Brown 12 pin 4T Blue (+) Fuse box, rear side ~
TYPE 1 - CHART - 2 OF 2 PAGE 7 OF 27 MAKE MODEL YEAR DESCRIPTION NAME TYPE POSITION POLARITY MODULE LOCION NISSAN COMPONENT LOCOR Altima Coupe Altima Sedan Altima Sedan Altima Hybrid Sedan Altima Hybrid Sedan Altima Hybrid Sedan Murano 13 07- -12 07- -12 13 10-14 Lock/Arm M18 Green 40 pin 56 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M18 Green 40 pin 34 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M18 Green 40 pin 58 LtBlue (-) BCM, behind cluster ~ Parking Light E6 White 10 pin 6M LtGreen (+) Fuse box, rear side ~ Lock/Arm M18 Green 40 pin 56 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M18 Green 40 pin 34 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M18 Green 40 pin 58 LtBlue (-) BCM, behind cluster ~ Parking Light B4 Brown 12 pin 4T Blue/Red (+) Fuse box, rear side ~ Lock/Arm M18 Green 40 pin 56 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M18 Green 40 pin 34 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M18 Green 40 pin 58 LtBlue (-) BCM, behind cluster ~ Parking Light B4 Brown 12 pin 4T Blue (+) Fuse box, rear side ~ Lock/Arm M18 Green 40 pin 56 Blue/Black (-) BCM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M18 Green 40 pin 34 Blue/Red (-) BCM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M18 Green 40 pin 58 LtBlue (-) BCM, behind cluster ~ Parking Light B4 Brown 12 pin 4T Blue/Red (+) Fuse box, rear side ~ Lock/Arm M18 Green 40 pin 56 Blue/Black (-) BCM, behind cluster ~ Unlock/Disarm M18 Green 40 pin 34 Blue/Red (-) BCM, behind cluster ~ Driver Door Pin M18 Green 40 pin 58 LtBlue (-) BCM, behind cluster ~ Parking Light B4 Brown 12 pin 4T Blue (+) Fuse box, rear side ~ Lock/Arm M18 Green 40 pin 56 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M18 Green 40 pin 34 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M18 Green 40 pin 58 LtBlue (-) BCM, behind cluster ~ Parking Light E6 White 10 pin 6M LtGreen (+) Fuse box, rear side ~ Lock/Arm M123 Green 40 pin 148 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M123 Green 40 pin 126 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M123 Green 40 pin 150 LtBlue (-) BCM, behind cluster ~ Parking Light B6 White 12 pin 4G Blue (+) Fuse box, rear side ~
TYPE 1 - WIRING DIAGRAM - 1 OF 1 PAGE 8 OF 27 VS10 SWITCH M1 M2 M3 M6 RF PORT/WEBLINK PORT M6 TELEMIC PORT M5 M4 VS9 1: 8 PIN 1: HARNESS LOCK ACC START STOP ENGINE ON M1 01 04 MS1 RELAY MS2 VS2 VS1 1: OBDII 16 PIN 1: OBDII HARNESS OBDII M2 01 04 07 10 11 12 13 14 15 16 17 18 19 20 MS3 M3 01 BROWN/BLACK GRAY - RAP SHUTDOWN (-) OUTPUT EMPTY 04 EMPTY EMPTY PURPLE/GREEN - LOCK (-) OUTPUT 07 EMPTY BLUE/GREEN EMPTY 10 EMPTY 11 GRAY/GREEN - HORN (-) OUTPUT 12 DKGREEN/GREEN - UNLOCK (-) OUTPUT VS4 VS3 VS5 VS6 WHITE VS11 VS12 VS7 VS8 PARKING LIGHT (+) THERE MAY BE NO CONNECTED TO THESE PINS, USE PROVIDED TERMINALS. SEE CHART. 1 1: BRAKE 4 PIN 1: BRAKE HARNESS 1: IMMOBILIZER 1: IMMOBILIZER HARNESS BRAKE SWITCH 1 KEYPORT SEE CHART BCM M123 / M18 M4 01 04 GRAY/WHITE - HOOD STUS (-) INPUT 07 10 LOCK/ARM (-) UNLOCK/DISARM (-) DRIVER DOOR PIN (-) 1 1 M123 OR M18 GREEN HORN (-) OPTIONAL HOOD SWITCH 2 2 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3
TYPE 2 - CHART - 1 OF 3 PAGE 9 OF 27 MAKE MODEL YEAR DESCRIPTION NAME TYPE POSITION POLARITY MODULE LOCION COMPONENT LOCOR INFINITI EX35 FX35 FX45 FX50 G35 Coupe G35 Sedan G37 G37 Convertible Driver Door Pin M123 Green 40 pin 150 LtGreen (-) BCM, passenger kick panel ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Driver Door Pin M123 Green 40 pin 150 Red (-) BCM, passenger kick panel ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~
TYPE 2 - CHART - 2 OF 3 PAGE 10 OF 27 MAKE MODEL YEAR DESCRIPTION NAME INFINITI TYPE POSITION POLARITY MODULE LOCION COMPONENT LOCOR NISSAN G37 Convertible G37 Convertible G37 Coup G37 Sedan G37 Coup/Sedan 370Z GTR Maxima 10 11-13 -10-10 11-13 -16-16 -14 Driver Door Pin M123 Green 40 pin 150 Red (-) BCM, passenger kick panel ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Driver Door Pin M123 Green 40 pin 150 Red (-) BCM, passenger kick panel ~ Parking Light M6 White 100 pin Red (+) Driver kick panel ~ Driver Door Pin M123 Green 40 pin 150 Red (-) BCM, passenger kick panel ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light M6 White 100 pin Red (+) Driver kick panel ~ Parking Light M2 White 10 pin 8B Red (+) Fuse box ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Lock/Arm M18 Green 40 pin 56 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Unlock/Disarm M18 Green 40 pin 34 Empty (-) BCM, behind cluster (use provided terminal for connection) ~ Driver Door Pin M18 Green 40 pin 58 LtBlue (-) BCM, behind cluster ~ Parking Light B4 Brown 12 pin 4T Blue (+) Fuse box, rear side ~
TYPE 2 - CHART - 3 OF 3 PAGE 11 OF 27 MAKE MODEL YEAR DESCRIPTION NAME TYPE NISSAN POSITION POLARITY MODULE LOCION COMPONENT LOCOR Murano Driver Door Pin M123 Green 40 pin 150 LtBlue (-) BCM, passenger kick panel ~ Parking Light B6 White 12 pin 4G Blue (+) Fuse box, rear side ~
TYPE 2 - WIRING DIAGRAM - 1 OF 1 PAGE 12 OF 27 VS10 SWITCH M1 M2 M3 M6 RF PORT/WEBLINK PORT M6 TELEMIC PORT M5 M4 VS9 1: 8 PIN 1: HARNESS LOCK ACC START STOP ENGINE ON M1 01 04 MS1 RELAY MS2 VS2 VS1 1: OBDII 16 PIN 1: OBDII HARNESS OBDII M2 01 04 07 10 11 12 13 14 15 16 17 18 19 20 MS3 M3 01 BROWN/BLACK GRAY - RAP SHUTDOWN (-) OUTPUT EMPTY 04 EMPTY EMPTY PURPLE/GREEN - LOCK (-) OUTPUT 07 EMPTY BLUE/GREEN EMPTY 10 EMPTY 11 GRAY/GREEN - HORN (-) OUTPUT 12 DKGREEN/GREEN - UNLOCK (-) OUTPUT VS4 VS3 VS5 VS6 WHITE VS11 VS12 VS7 VS8 PARKING LIGHT (+) THERE MAY BE NO CONNECTED TO THESE PINS, USE PROVIDED TERMINALS. SEE CHART. 1 1: BRAKE 4 PIN 1: BRAKE HARNESS 1: IMMOBILIZER 1: IMMOBILIZER HARNESS BRAKE SWITCH 1 KEYPORT SEE CHART BCM M123 / M18 M4 01 04 GRAY/WHITE - HOOD STUS (-) INPUT 07 10 LOCK/ARM (-) UNLOCK/DISARM (-) DRIVER DOOR PIN (-) 1 1 M123 OR M18 GREEN HORN (-) OPTIONAL HOOD SWITCH 2 2 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3
TYPE 3 - CHART - 1 OF 1 PAGE 13 OF 27 MAKE MODEL YEAR DESCRIPTION NAME TYPE INFINITI POSITION POLARITY MODULE LOCION COMPONENT LOCOR Q60 Convertible Q60 Coupe 14-15 14-15 Driver Door Pin M123 Green 40 pin 150 Red (-) BCM, passenger kick panel ~ Parking Light M6 White 100 pin Red (+) Driver kick panel ~ Driver Door Pin M123 Green 40 pin 150 Red (-) BCM, passenger kick panel ~ Parking Light M6 White 100 pin Red (+) Driver kick panel ~
TYPE 3 - WIRING DIAGRAM - 1 OF 1 PAGE 14 OF 27 VS10 SWITCH M1 M2 M3 M6 RF PORT/WEBLINK PORT M6 TELEMIC PORT M5 M4 VS9 1: 8 PIN 1: HARNESS LOCK ACC START STOP ENGINE ON M1 01 04 MS1 RELAY MS2 VS2 VS1 1: OBDII 16 PIN 1: OBDII HARNESS OBDII M2 01 04 07 10 11 12 13 14 15 16 17 18 19 20 MS3 M3 01 BROWN/BLACK GRAY - RAP SHUTDOWN (-) OUTPUT EMPTY 04 EMPTY EMPTY PURPLE/GREEN 07 EMPTY BLUE/GREEN EMPTY 10 EMPTY 11 GRAY/GREEN - HORN (-) OUTPUT 12 DKGREEN/GREEN VS4 VS3 VS5 VS6 WHITE VS11 VS12 VS7 VS8 PARKING LIGHT (+) 1: BRAKE 4 PIN 1: BRAKE HARNESS 1: IMMOBILIZER 1: IMMOBILIZER HARNESS BRAKE SWITCH 1 KEYPORT SEE CHART BCM M123 M4 01 04 GRAY/WHITE - HOOD STUS (-) INPUT 07 10 DRIVER DOOR PIN (-) - 150 M123 : GREEN 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 HORN (-) OPTIONAL HOOD SWITCH 2 2 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3
TYPE 4 - CHART - 1 OF 1 PAGE 15 OF 27 MAKE MODEL YEAR DESCRIPTION NAME TYPE INFINITI POSITION POLARITY MODULE LOCION COMPONENT LOCOR QX50 QX70 14-16 14-16 Driver Door Pin M123 Green 40 pin 150 LtGreen (-) BCM, passenger kick panel ~ Parking Light B6 White 12 pin 4G Red (+) Fuse box, rear side ~ Parking Light M2 White 10 pin 8B Red (+) Fuse box ~
TYPE 4 - WIRING DIAGRAM - 1 OF 1 PAGE 16 OF 27 VS10 SWITCH M1 M2 M3 M6 RF PORT/WEBLINK PORT M6 TELEMIC PORT M5 M4 VS9 1: 8 PIN 1: HARNESS LOCK ACC START STOP ENGINE ON M1 01 04 MS1 RELAY MS2 VS2 VS1 1: OBDII 16 PIN 1: OBDII HARNESS OBDII M2 01 04 07 10 11 12 13 14 15 16 17 18 19 20 MS3 M3 01 BROWN/BLACK GRAY - RAP SHUTDOWN (-) OUTPUT EMPTY 04 EMPTY EMPTY PURPLE/GREEN 07 EMPTY BLUE/GREEN EMPTY 10 EMPTY 11 GRAY/GREEN - HORN (-) OUTPUT 12 DKGREEN/GREEN VS4 VS3 VS5 VS6 WHITE VS11 VS12 VS7 VS8 PARKING LIGHT (+) 1: BRAKE 4 PIN 1: BRAKE HARNESS 1: IMMOBILIZER 1: IMMOBILIZER HARNESS BRAKE SWITCH 1 KEYPORT SEE CHART BCM M123 M4 01 04 GRAY/WHITE - HOOD STUS (-) INPUT 07 10 DRIVER DOOR PIN (-) - 150 M123 : GREEN 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 HORN (-) OPTIONAL HOOD SWITCH 2 2 3 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3
HOLD MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 17 OF 27 01 When programming, only one keyfob will be used. Place the other one at least 10 feet away from the vehicle. Insert keyfob 1 in keyport. STOP ACC ON START Do not press brake pedal. Push start button twice [2x] to ON position. ENGINE START STOP 04 Wait, LED 1 will turn solid GREEN then will turn OFF. STOP ACC ON START Do not press brake pedal. Push start button once [1x] to OFF position. ENGINE START STOP Module Programming Procedure completed.
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 18 OF 27 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps 1 to 5. 01 Time restriction. Complete next step within 7 seconds. OFF ACC ON START Cycle ignition ON five times [5x OFF/ON] rapidly. ENGINE START STOP Wait, LED 1 will turn solid RED for 2 seconds. 04 OFF ACC ON START Set ignition to OFF position. ENGINE START STOP Valet Mode Programming Procedure completed.
AFTERMARKET REMOTE PROGRAMMING - 1 OF 1 PAGE 19 OF 27 AFTERMARKET REMOTE PROGRAMMING: NOTES I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.
PAGE 20 OF 27 MODULE NAVIGION PROCEDURE - 1 OF 1 >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 13. 04 >> Module must be programmed to the vehicle. >> Use the Module Navigation Chart on the next page. Set ignition to OFF position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid GREEN. IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will flash GREEN an equal amount of times continuously. 01 OFF ACC ON START DOC.: #54560 201818 TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid RED. 10 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will flash RED an equal amount of times continuously. 11 TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid GREEN. 12 Configure every other setting and proceed to step 13. [Z] LED 1 will flash GREEN as many times as the current (or default) setting number, continuously. 13 MANDORY: EXIT MODULE NAVIGION. Press and hold programming button for 7 seconds. LED 1 will flash RED rapidly. Release programming button. LED 1 will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will flash GREEN an equal amount of times continuously. 14 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED. [Y] LED 1 will flash RED as many times as the current option number continuously. ENGINE START STOP [X]
MODULE NAVIGION CHART - 1 OF 2 PAGE 21 OF 27 MODULE NAVIGION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 01 CONFIGURION 01 DISARM/UNLOCK BEFORE START 01 OFF ON RELOCK AFTER START 01 OFF ON RELOCK AFTER SHUTDOWN 01 OFF ON 04 FORCE UNLOCK ALL ON FIRST PRESS 01 OFF ON TAKEOVER 01 ENABLE DISABLE* N/A 01 N/A 01 DISABLE 07 FACTORY KEYLESS RS SEQUENCE N/A LOCK + UNLOCK + LOCK 04 LOCK + LOCK + LOCK 01 MIN MIN 10 MIN MODULE RUN TIME 04 15 MIN 25 MIN 30 MIN 07 35 MIN 15 MIN 01 SEC SEC SEC WAIT TO START DELAY 04 10 SEC 15 SEC 20 SEC 07 25 SEC 30 SEC 10 N/A 01 N/A 11 N/A 01 N/A 12 N/A 01 N/A 13 N/A 01 N/A
MODULE NAVIGION CHART - 2 OF 2 PAGE 22 OF 27 MODULE NAVIGION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS *Vehicle will shutdown when a door is opened. 01 DOUBLE LOCK 14 HORN EVENT TRIGGER LOCK + UNLOCK LOCK + UNLOCK + START 01 CONFIGURION 04 DOUBLE LOCK + START 01 30 msec 15 HORN CHIRPS WIDTH 15 msec 60 msec -07 Technical Support only 01 N/A 01 N/A
REMOTE STARTER ERROR CODES - 1 OF 1 PAGE 23 OF 27 REMOTE STARTER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. Foot brake is ON. 04 Hood is open. Engine tach signal is lost. System is in Valet Mode. 07 Vehicle is moving (VSS). Glow plug timeout error. RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 10 N/A 11 N/A 12 N/A 13 N/A 14 N/A 15 N/A 16 CAN communication failure during RS sequence.
MODULE DIAGNOSTICS - 1 OF 1 PAGE 24 OF 27 TEST MODULE LED 1 STUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.
MODULE RESET PROCEDURE - 1 OF 1 PAGE 25 OF 27 01 Disconnect all connectors from module except the BLACK 20-PIN connector. 07 Reconnect all connectors. Disconnect the BLACK 20-PIN connector. Repeat programming procedure. PRESS AND HOLD the module s programming button while connecting the BLACK 20-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELEASE programming button. LED 1 will turn RED for 2 seconds. Module RESET completed.
TAKEOVER PROCEDURE - - 1 OF 1 PAGE 26 OF 27 >> All vehicle doors must be closed and locked prior to remote start sequence. Take over procedure completed. 01 Time restriction. Complete steps 2 to 5 within 45 seconds. >> Failure to follow procedure will result in vehicle engine shutdown. Press unlock on OEM or aftermarket remote. Open driver door and enter vehicle. 04 Close driver door. Press and release BRAKE pedal.
INSTALLION CHECKLIST - 1 OF 1 PAGE 27 OF 27 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. 10 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.