Hydro 88 & 96 Flail Rev 0- PARTS MANUAL Part No.8033 ALAMO INDUSTRIAL 50 E. Walnut Seguin, Texas 7855 830-37-9595 An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial (800-356-686) to obtain a Free copy before operating the equipment. 03 Alamo Group, Inc.
TORQUE Mounting procedures for mowers will require a significant amount of bolt nut and washer installation. Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values listed in the torque chart based on the bolt size and hardness. Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry values indicated in the chart. Bolt tightness should be completed with and checked with a suitable torque wrench. Torque checks should be completed throughout the life of the mower in accordance with the maintenance chart provided in this manual. Loose bolts on a frame or in a casting may be a result of: Vibration from the mower due to imbalance of the mower blades Pulled threads due to over tightening Distortion of the hole due to under tightening during installation Bolts broken or sheared in the mounting structure or tractor may be the result of: Improper alignment of the Mounting Plate or Structure such that it is not sitting flat on the mating surface Distortion of the bolt due to over-tightening Under tightening of the bolts Check the bolt torque during installation and prior to delivery with a suitable torque wrench.
To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
CHANGE PAGES Date of Change Page Number 0-03-03 (EXAMPLE ONLY: ECN##### - chg pages 7, 3, 37) 0-03-03 document release date Change Pages - 5
CHANGE PAGES The following is a listing of pages that have been changed since the latest publication date for the overall document. Change Pages - 6
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. Note: Please refer to The Safety Section in the front of this Manual for the proper part number when ordering replacement safety decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Industrial Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: ALAMO INDUSTRIAL 50 E. Walnut Seguin, Texas 7855 830-379-80 03 Alamo Group Inc. Parts Section
PART NAME INDEX FILTER ASY. P/N 09678... GENERAL ASY... 6 HYD. MOTOR ASY. P/N 703875... 8 HYD. MOTOR REPLACEMENT PARTS - P/N 0060... 0 HYD. MOTOR REPLACEMENT PARTS - P/N 09855... HYD. SCHEMATIC... MOWER ASY 88 (PART )... 6 MOWER ASY 88 (PART )... 8 MOWER ASY. 96 (PART )... 0 MOWER ASY. 96 (PART )... 3 PUMP ASY... 5 PUMP CONNECTION... 6 SPEED INCREASER & PUMP ASY... 7 SPEED INCREASER P/N 00768956 ( NEW STYLE )... 9 SPEED INCREASER P/N 0897900 ( OLD STYLE )... 3 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -3
FILTER ASY. P/N 09678 ITEM PART NO. QTY. DESCRIPTION 09678 - FILTER ASY. W/ ELEMENT 09600 FILTER ELEMENT ONLY 097678 SPRING FILTER CARTRIDGE 3 097378 VALVE, FILTER BYPASS 097839 FILTER COVER 5 097835 SEAL KIT 6 0978355 NUT & KIT, F/ FILTER COVER. 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -
THIS PAGE INTENTIONALLY LEFT BLANK 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -5
GENERAL ASY ITEM PART NO. QTY. DESCRIPTION 070 HYDRAULIC TANK WLD`MT 09678 FILTER HOUSING ASY. 3 09677 O-RING 00065 5 009500 LOCKWASHER 7 0000800 5 LOCKNUT TLM / NC PLC 9 007883 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -6
GENERAL ASY Continued... ITEM PART NO. QTY. DESCRIPTION 0 0700 MOUNT 0069500 6 NUT,TOPLOCK 5/8 NC PLC 085500 3 00008300 070 OVERARM WLD`MT 5 00059000 6 0703 SPACER 7 0375 A-FRAME 8 0776600 3 9 0073 HITCH - PIN 0 96 CLIP - LYNCH PIN 0667 SPACER 095933 3 0003700 LOCKNUT 0703 BRACE 5 0075530 FILTER ELEMENT - BREATHER 7 09600 FILTER ELEMENT 8 009700 SIGHT - GAUGE 9 0779 PIN 30 0377 SPACER 3 0376 SPACER 3 097678 SPRING FILTER CARTRIDGE 33 097378 VALVE FILTER BYPASS 3 097839 FILTER COVER --- 097835 SEAL KIT 0978355 NUT AND KIT 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -7
HYD. MOTOR ASY. P/N 703875 ITEM PART NO. QTY. DESCRIPTION 703875 - MOTOR ASY, HYD. (ITEMS THRU 7) 03005 KEY 0076 HUB 3 0000 3 00067 PULLEY 5 0658 MOTOR MOUNT PLATE 6 0065 ADAPTER - ELBOW 7 007883 8 0000800 LOCKNUT TLM / NC PLC 9 0060 MOTOR. 0 0090900 ADAPTER - ELBOW 030083 STRAIGHT ADAPTER 0057 CAP NUT 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -8
HYD. MOTOR ASY. P/N 703875 Continued... ITEM PART NO. QTY. DESCRIPTION 3 630900 000700 7 LOCKWASHER 5 00759 RELIEF VALVE 6 09656 MANIFOLD BLOCK 7 096793 O-RING 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -9
HYD. MOTOR REPLACEMENT PARTS - P/N 0060 ITEM PART NO. QTY. DESCRIPTION 0060 MOTOR W/KEY.8 CU/IN. 006 ROTATING KIT ASY 006 PLATE ASY, BACKING 3 0063 SHAFT, KEYED NFS HOUSING ASY, (NOT FURNISHED AS PARTS) 5 006 BEARING & RACE SET 6 0065 PLATE, CAM INSERT 7 030009 O-RING 8 000600 HHCS 5/6NC PL5 9 0300 WASHER 0 096695 RING, SPIRAL 09770 RETAINING RING 096696 KIT, SEAL ADAPTER 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -0
HYD. MOTOR REPLACEMENT PARTS - P/N 0060 Continued... ITEM PART NO. QTY. DESCRIPTION A 09669 O-RING,.0 X -3/6 B 09669 SEAL, HIGH PRESSURE C 096693 SEAL ADAPTER,.00 BORE 3 03005 STEP KEY, / X 5/6 0300587 PLUG, HEX HD # 8MB 5 00339 BEARING, BACKPLATE 6 0030 BEARING HOUSING 0068 SEAL KIT 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -
HYD. MOTOR REPLACEMENT PARTS - P/N 09855 ITEM PART NO. QTY. DESCRIPTION 09855 MOTOR W/KEY.8 CU/IN. 006 ROTATING KIT ASY 098603 PLATE ASY, BACKING 3 0063 SHAFT, KEYED NFS HOUSING ASY, (NOT FURNISHED AS PARTS) 5 006 BEARING & RACE SET 6 0065 PLATE, CAM INSERT 7 030009 O-RING 8 000600 HHCS 5/6NC PL5 9 0300 WASHER 0 096695 RING, SPIRAL 09770 RETAINING RING 096696 KIT, SEAL ADAPTER 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -
HYD. MOTOR REPLACEMENT PARTS - P/N 09855 Continued... ITEM PART NO. QTY. DESCRIPTION A 09669 O-RING,.0 X -3/6 B 09669 SEAL, HIGH PRESSURE C 096693 SEAL ADAPTER,.00 BORE 3 03005 STEP KEY, / X 5/6 0300587 PLUG, HEX HD # 8MB 5 00339 BEARING, BACKPLATE ASY 6 0030 BEARING HOUSING 7 0986033 VALVE PLATE 0068 SEAL KIT 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -3
HYD. SCHEMATIC ITEM PART NO. QTY. DESCRIPTION 0068 HOSE - CROSS OVER 0756 SUCTION - HOSE 3 07558 HOSE 07800 HOSE 5 07557 HOSE 6 075900 HOSE 7 096009 ADAPTER, TUBE, ELBOW 8 030077 HOSE 9* 095685 ADAPTER HYD. ELBOW 0 0059 STRAIGHT ADAPTER - REDUCER 030350 FILLER PLUG 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -
THIS PAGE INTENTIONALLY LEFT BLANK 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -5
MOWER ASY 88 (PART ) 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -6
MOWER ASY 88 (PART ) Continued... ITEM PART NO. QTY. DESCRIPTION 0709 CUTTER HOUSING WLD`MT 88" 703875 MOTOR ASY. 3 0658 MOTOR MOUNT PLATE 007883 5 0000800 LOCKNUT TLM / NC PLC 6 00067 PULLEY 7 0076 HUB 8 00070 V-BELTS - MATCHED PAIR 0659 IDLER ARM WLD`MT, RH 7077 IDLER ARM ASY.,RH (FWD ROT) 00000 000700 LOCKWASHER 0003500 FLATWASHER 00006 NO. RED LUBRICAPS 0 0305 IDLER PULLEY 0778 SPACER 000539 SPRING 3 0709 BELT GUARD WLD`MT 003500 00000 FLATWASHER 03066 LOCKWASHER 03065 CUTTERSHAFT PULLEY 5 00768 KEY 6 0070 WASHER 7 0000300 LOCKWASHER 8 00007 9 70385 BEARING & HOUSING ASY. ( DRIVE SIDE ) 0035 BEARING 703596 ROLLER ASY. 0778 ROLLER - 88", WLD`MT 00056 CARRIAGE 0000800 LOCKNUT TLM / NC PLC 075 CUTTERSHAFT - 88" 098633 88 COURSE CUT KNIFE 3 0076 RING 0670 PIN 5 0668700 COTTER PIN 6 0305 SHOE/WEAR PLATE 7 A383 PLOW 8 0886900 9 06 IDLER PIVOT PIN 9 0 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -7
MOWER ASY 88 (PART ) 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -8
MOWER ASY 88 (PART ) Continued... ITEM PART NO. QTY. DESCRIPTION 0075670 FITTING,GREASE STRAIGHT /-8 7037 BEARING, ASY, CUTTERSHAFT 0035 BEARING CUTTERSHAFT 3 007536 HEXB 3 0005800 LOCKNUT TLM 33 00000 FLATWASHER STD 3/8 3 0306 FENDER 35 00755 DEFLECTOR,TRASH,88 (REAR) 36 0058000 HHCS 37 00000 FLATWASHER STD / 38 09599 NUT TOPLOCK 39 0759 WLDMT, FOOT GUARD 88, INT 0 0030700 6 HHCS / NC / PL5 0009600 LOCKWASHER / HEAVY PL 000000 NUT / NC HEX PL 70369 ASY ROLLER BRG & HSG 703976 ASY- ROLLER BRG W/HEX BORE 0730 HOUSING,BEARING,MACHINED 0000 BEARING,ROLLER 30 3/8 NC X -/ PL5 3/8-NC PLC / NC PL5 PL / NC PLB 0086 BEARING-REAR ROLLER W/HEX BORE 3 00039 ASY GREASE FTG /-8 90 DEG 00037 SEAL- ROLLER BRG 5 00056 CARB 6 078 USE 097676 70363 ASSY,ROLLER BRG/BRKT,LH 07380 USE 097676 703596 ASSY,ROLLER BRG/BRKT,RH 7 0560 FENDER,GUARD 8 070 SPACER / NC -3/ 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -9
MOWER ASY. 96 (PART ) 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -0
MOWER ASY. 96 (PART ) Continued... ITEM PART NO. QTY. DESCRIPTION 0806 CUTTER HOUSING WLD`MT 96" 703875 MOTOR ASY. 3 0658 MOTOR MOUNT PLATE 007883 5 0000800 LOCKNUT TLM / NC PLC 6 00067 PULLEY 7 0076 HUB 8 00070 V-BELTS - MATCHED PAIR 0659 IDLER ARM WLD`MT, RH 7077 IDLER ARM ASY.,RH (FWD ROT) 00000 000700 LOCKWASHER 0003500 FLATWASHER 00006 NO. RED LUBRICAPS 0 0305 IDLER PULLEY 0778 SPACER 000539 SPRING 3 0709 BELT GUARD WLD`MT 003500 00000 FLATWASHER 03066 LOCKWASHER 03065 CUTTERSHAFT PULLEY 5 00768 KEY 6 0070 WASHER 7 0000300 LOCKWASHER 8 00007 9 70385 BEARING & HOUSING ASY. ( DRIVE SIDE ) 0035 BEARING 703596 ROLLER ASY. 07787 ROLLER - 96", WLD`MT 00056 CARRIAGE 0000800 LOCKNUT TLM / NC PLC 0775 CUTTERSHAFT - 96" 00759 96 COURSE CUT KNIFE 9 0 098633 96 COURSE CUT KNIFE 3 0076 8 RING 0670 8 PIN 5 0668700 8 COTTER PIN 6 0305 SHOE/WEAR PLATE 7 A383 PLOW 8 0886900 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -
MOWER ASY. 96 (PART ) Continued... ITEM PART NO. QTY. DESCRIPTION 9 06 IDLER PIVOT PIN 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -
MOWER ASY. 96 (PART ) 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -3
MOWER ASY. 96 (PART ) Continued... ITEM PART NO. QTY. DESCRIPTION 0075670 FITTING,GREASE STRAIGHT /-8 7037 BEARING, ASY, CUTTERSHAFT 0035 BEARING CUTTERSHAFT 3 007536 HEXB 3 0005800 LOCKNUT TLM 33 00000 FLATWASHER STD 3/8 3 0306 FENDER 35 07753 DEFLECTOR,TRASH,96 (REAR) 36 0058000 3 HHCS 37 00000 3 FLATWASHER STD / 38 09599 3 NUT TOPLOCK 39 0808 WLDMT,FOOT GUARD 0 0030700 6 HHCS / NC / PL5 0009600 LOCKWASHER / HEAVY PL 000000 NUT / NC HEX PL 70369 ASY ROLLER BRG & HSG 703976 ASY- ROLLER BRG W/HEX BORE 0730 HOUSING,BEARING,MACHINED 0000 BEARING,ROLLER 30 3/8 NC X -/ PL5 3/8-NC PLC / NC PL5 PL / NC PLB 0086 BEARING-REAR ROLLER W/HEX BORE 3 00039 ASY GREASE FTG /-8 90 DEG 00037 SEAL- ROLLER BRG 5 00056 CARB 6 078 USE 097676 70363 ASSY,ROLLER BRG/BRKT,LH 07380 USE 097676 703596 ASSY,ROLLER BRG/BRKT,RH 7 0560 FENDER,GUARD 8 070 SPACER / NC -3/ 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -
PUMP ASY. ITEM PART NO. QTY. DESCRIPTION 030000 ROTATING KIT ASY. 096535 BACK PLATE ASY. 3 030008 CAMPLATE INSERT 03000 SPLINED SHAFT 5 006 BEARING & CONE KIT 6 030009 O-RING 7 076600 6 8 0300 WASHER 9 0300 RETAINING RING 0 03003 RETAINING RING 0300 SHAFT SEAL 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -5
PUMP CONNECTION ITEM PART NO. QTY. DESCRIPTION 0060 PUMP ASY. W/FITTINGS 030083 STRAIGHT ADAPTER 3 09576 STRAIGHT ADAPTER 096098 ADAPTER HYD. ELBOW 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -6
SPEED INCREASER & PUMP ASY. ITEM PART NO. QTY. DESCRIPTION 00768956 - SPEED INCREASER,(NEW STYLE ALUMINUM HOUSING) 0897900 SPEED INCREASER (OLD STYLE STEEL HOUSING) 0009600 LOCKWASHER 3 00750959 0060 PUMP 5 096098 ADAPTER HYD. ELBOW 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -7
THIS PAGE INTENTIONALLY LEFT BLANK 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -8
SPEED INCREASER P/N 00768956 ( NEW STYLE ) 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -9
SPEED INCREASER P/N 00768956 ( NEW STYLE ) Continued... ITEM PART NO. QTY. DESCRIPTION 00768956 - SPEED INCREASER ASY, (NEW STYLE ALUMINUM HOUSING) 007559 HOUSING 007550 GASKET 3 00755 GASKET 00755 FLANGE 5 007553 BREATHER PLUG 6 00755 ALUMINUM WASHER 7 007555 3 PLUG 8 007556 3 LOCKWASHER 9 007557 8 0 007558 0 LOCKWASHER 007559 0 0075530 DOWEL PIN 3 007553 HOUSING 007553 GASKET 5 0075533 FLANGE 6 007553 GASKET 7 0075535 DIPSTICK 8 0075536 5 ALUMINUM WASHER 9 0075537 PLUG 0 0075538 DOUBLE LIP SEAL 0075539 BEARING 007550 RETAINING RING 3 00755 3 BEARING 00755 SHAFT 5 007553 KEY 6 00755 GEAR ( 50 RPM ) 0075653 GEAR ( 000 RPM ) 007555 PINION GEAR ( 50 RPM ) 0075653 PINION GEAR ( 000 RPM ) 8 007556 SPACER 9 0075950 PUMP FLANGE 30 007595 - PUMP ADAPTER.55" X 0 SPL O.D. & 7/8" X 3 SPL I.D. 7 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -30
SPEED INCREASER P/N 0897900 ( OLD STYLE ) 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -3
SPEED INCREASER P/N 0897900 ( OLD STYLE ) Continued... ITEM PART NO. QTY. DESCRIPTION 0897900 - SPEED INCREASER ASY, (OLD STYLE STEEL HOUSING) 09700 PUMP ADAPTER - -3/" X 3 SPL O.D. & 7/8" X -3 SPL I.D. ---------- GEAR - 8 TEETH 5 007579 GEAR, 7 TEETH 6 09600 PUMP FLANGE 7 007599 COVER, CLOSED 8 0075950 COVER, OPEN 9 0075970 8 PIPE PLUG 0 0075535 3 SEAL 007595 RETAINING RING 00759 BREATHER 3 007595 BEARING CUP 0075533 BEARING CONE 5 00790 3 BEARING CUP 6 007900 3 BEARING CONE 7 0075953 SPACER RING 8 0075955 HOUSING 9 0075956 HOUSING 0 0075957 DOWEL PIN 0075958 GASKET -.05 007597 SPACER RING 0075959 - SHIM.005 ALUM 5 0075960 - SHIM.007 ALUM 6 007596 - SHIM.00 ALUM 8 0075963 SHIM.005 ALUM 9 007596 SHIM.005 FIBRE 30 0075965 - SHIM.007 ALUM 3 0075966 - SHIM.00 ALUM 3 0075967 33 0075968 LOCKWASHER 3 0075969 8 35 000390 8 NUT 36 0000 8 LOCKWASHER 8033 - Hydro 88 and 96 (08-03)_0-0 Alamo Group Inc. Parts Section -3
TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manuals thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (98.5 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER. Provide a Roll-Over-Protective Structure that meets the requirements of this standard.. Provide seat belts that meet the requirements of this paragraph of this standard and SAE JC. 3. Ensure that each employee uses such seat belt while the tractor is moving.. Ensure that each employee tightens the seat belt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR. Securely fasten seat belt if the tractor has a ROPS.. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.. Stay off slopes too steep for safe operation. 5. Watch where you are going, especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly, no jerky turns, starts, or stops. 8. Hitch only to the draw bar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
ALAMO INDUSTRIAL Limited Warranty. Limited Warranties.0. Alamo industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( purchaser ) and warrants for six months to the original commercial or industrial purchaser ( purchaser ) that the goods purchased are free from defects in material or workmanship..0. Manufacturer will replace for the purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship..03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your operator s manual..0. Except as provided herein, no employee, agent, dealer, or other person is authorized to give any warranties of any nature on behalf of manufacturer.. Remedies And Procedures.0. This limited warranty is not effective unless the purchaser returns the registration and warranty form to manufacturer within 30 days of purchase..0. Purchaser claims must be made in writing to the authorized dealer ( dealer ) from whom purchaser purchased the goods or an approved authorized dealer ( dealer ) within 30 days after purchaser learns of the facts on which the claim is based..03. Purchaser is responsible for returning the goods in question to the dealer..0. If after examining the goods and/or parts in question, manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, manufacturer will: (A) repair or replace the defective goods or part(s) or (B) reimburse purchaser for the cost of the part(s) and reasonable labor charges (as determined by manufacturer) if purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by manufacturer. The choice of remedy shall belong to manufacturer..05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by manufacturer and for returning the goods to the dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the dealer to the designated factory. 3. Limitation Of Liability 3.0. Manufacturer disclaims any express (except as set forth herein) and implied warranties with respect to the goods including, but not limited to, merchantability and fitness for a particular purpose. 3.0. Manufacturer makes no warranty as to the design, capability, capacity, or suitability for use of the goods. 3.03. Except as provided herein, manufacturer shall have no liability or responsibility to purchaser or any other person or entity with respect to any liability, loss, or damage caused or alleged to be caused directly or indirectly by the goods including, but not limited to, any indirect, special, consequential, or incidental damages resulting from the use or operation of the goods or any breach of this warranty. Not withstanding the above limitations and warranties, manufacturer s liability hereunder for damages incurred by purchaser or others shall not exceed the price of the goods. 3.0. No action arising out of any claimed breach of this warranty or transactions under this warranty may be brought more than two () years after the cause of action has occurred.. Miscellaneous.0. Proper venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe county, Texas..0. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term..03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein..0. Applicable law may provide rights and benefits to purchaser in addition to those provided herein. Keep for your records Attention: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Alamo Industrial Implement Model Serial Number Date Purchased Dealer Attention: Read your operator s manual ALAMO INDUSTRIAL 50 E. Walnut Seguin, Texas 7855 830-379-80
50 E. Walnut St. Seguin, Texas 7855 Sales and Marketing Tel 800.88.576 Fax 830.379.086 support@alamo-industrial.com Warranty Registration/Claims www.alamoparts.com Return Authorizations Online Part Orders Techical Information www.alamoparts.com Tel 800.356.686 Fax 800.3.5 www.alamo-industrial.com Hydro 88 and 96 Parts Manual (PUB 03-08) P/N 8033