Operating and Installation Instructions Mini Diaphragm Vacuum Pumps Type ranges: UN828KNI UN838KNI UN838.1.2KNI UN828ANI UN838ANI UN828KNDCB UN828KNDC UN838KNDC UN838KNDCB UN828ANDC UN838ANDC UN838.1.2KNDCB Fig. 1: UN828KNDC Fig. 2: UN828ANI Fig. 3: UN838.1.2KNI You have selected a high-quality KNF product; the following tips will help you operate it safely and reliably over a long period of time. Carefully study the Operating and Installation Instructions before using the pumps and observe at all times the relevant instructions to avoid dangerous situations. The manual was produced for the serial pumps stated above. With customer-specified projects (pump types starting with PU or MPU ) there could be differences in detail. For customer-specified projects please therefore take into account any agreed technical specifications, as well as these instructions. KNF Neuberger, Inc 2 Black Forest Rd Trenton, NJ 08691-1810 Phone: 609-890-8600 Fax: 609-890-8323 www.knf.com/usa.htm Ident#121249-125933 Revision (05/12) List of Contents Page 1. Description, Operating Conditions... 2 2. Safety... 4 3. Installation... 6 4. Operation... 8 5. Servicing... 10 6. Cleaning... 17 7. Trouble Shooting... 18 8. Spare parts and accessories... 20 9. Tables... 21 10. Product Return... 22
Description, Operating Conditions Diaphragm Vacuum Pumps UN828, UN838_I 1. Description, Operating Conditions KNF pumps in the UN828 and UN838 range transfer and evacuate 100% oil-free. In operation they are gas-tight, and maintenancefree. 1.1. Electrical Equipment See the motor-plate for full electrical data. Protection class of standard version is: N828 KNE, N828 ANE, N828 KNDC, N828 ANDC, N838 KNE, N838 ANE, N838 KNDC, N838 ANDC: o IP 00 N838.1.2 KNE, N828 KNDCB, N838 KNDCB, N838.1.2 KNDCB: o IP 20 The ac motors used in the N 828 and N 838 range are fitted as standard with thermal switch to protect against overloading. The pumps with brushless DC motor are protected against overheating by a temperature sensor on the motor board and equipped with overcurrent protection. 1.2. Operating Conditions Handling air, gases, and vapours at temperatures between + 5 C + 40 C. For maximum permissible operating pressure, ultimate vacuum, and flow capacity see section 10. The pumps must not be used in areas where there is a danger of explosion. The pumps are not suitable for aggressive media. For aggressive media there are other pumps in the KNF product programme - please ask us for detail. For vacuum pumps, the exhaust gases must be safely disposed. Before pumping a medium, the compatibility of materials of pump head, diaphragm and valves with the medium must be checked (for pump materials: section 10). KNF pumps in the UN828 and UN838 range must not be used for liquids. You will find suitable liquid pumps in our Product Program. If your potential application lies outside the above limits discuss it with our technical adviser (see last page for contact telephone number). 2
Diaphragm Vacuum Pumps UN828, UN838_I Description, Operating Conditions 1.3. Ambient Conditions When the pump is operating the following ambient conditions must be maintained: Ambient temperature during operation: between + 5 C + 40 C. The pumps must not be used in areas where there is a danger of explosion. The pumps must be protected from the effects of dust and water. During operation an adequate supply of air for cooling must be provided. 1.4. Pump materials See section 10. 3
Safety Diaphragm Vacuum Pumps UN828, UN838_I EC Directives / Standards 2. Safety For pumps with ac motors: The pumps have Protection Class IP00 or IP20, and so offer no protection against contact or foreign bodies. It is therefore essential to provide protection for persons against contact with live parts (e.g. electrical connections, motor windings), and moving parts (e.g. fan). Protection against the entry of foreign bodies must also be provided. The pumps have no protection against water. In this case too, as far as is relevant, measures to protect the pump must be taken before putting it into service. Note that the pumps may only be used for their intended purpose. The pumps must not be used in areas where there is a danger of explosion. The pumps are not suitable for aggressive media. For aggressive media there are other pumps in the KNF product programme - please ask us for detail. Components connected to the pump must be designed to withstand the pneumatic performance of the pump. For vacuum pumps, the exhaust gases must be safely disposed. Take care that safety regulations are observed when connecting the pump to the electricity supply. For pumps with a thermal switch: When the operation of the pump is interrupted by the thermal switch, the pump will re-start automatically after cooling down. Take all care necessary to prevent this leading to a dangerous situation. Specific safety instructions for the media being handled must be observed. Use only original KNF spare parts. For the purposes of the Machinery Directive 2006/42/EC, pumps are partly completed machinery, and are therefore to be regarded as not ready for use. Partly completed machinery may not be commissioned until such time as it has been determined that the machine in which the partly completed machinery is to be assembled is in conformity with the provisions of the Machinery Directive 2006/42/EC. The following essential requirements of Annex I of Directive 2006/42/EC (general principles) are applied and observed: General Principles No. 1 No. 1.1.3 / 1.1.3 /1.3.1 / 1.3.4 / 1.4.1 / 1.5.1* / 1.5.2* / 1.5.8 / 1.5.9 / 1.7.4 / 1.7.4.1 / 1.7.4.3 (* only for pumps with AC motor) As these partly completed machinery are OEM-models the power supplies and the equipment for disconnecting and switching-off the partly completed machinery respectively have to be considered 4
Diaphragm Vacuum Pumps UN828, UN838_I Safety when mounting as well as over-current and overload protective gear. In addition a protection against mechanical parts in motion and hot parts, if existing, has to be provided when mounting. The pumps conform to the EC Directive 201/65/EU (RoHS2). The pumps conform to the EC Directive 2004/108/EC concerning Electromagnetic Compatibility. The following harmonized standards have been used: UN828_NE UN838_NE UN838.1.2KNE UN828_NDC UN838_NDC DIN EN 55014-1/2 DIN EN 55014-1/2 DIN EN 61000-3-2/3 DIN EN 60034-1 DIN EN 60335-1 Tab. 1 5
Installation Diaphragm Vacuum Pumps UN828, UN838_I Mechanical Electrical 3. Installation Pumps in the UN828 and UN838 range are OEM models intended for installation in equipment. When installing them make certain that accident prevention regulations, and safety instructions, including those for subsequent operation are observed. The safety instructions in section 2 must be observed. The dimensions of the mountings are given in Data Sheet. Install the pump so that the fan can draw in sufficient cooling air. For pumps with fan: Install the pump so as accidental finger contact is with the fan is impossible. Fit the pump at the highest point in the system, so that condensate cannot collect in the head of the pump - that prolongs working life. When making the electrical installation the safety regulations must be observed. In particular make sure that the electricity supply is isolated before trying to connect the pump. Compare the supply data with the data on the motor-plate. The voltage must not vary by more than +10 % and 10 % from that shown on the type-plate. The earth (ground) wire must be connected to the motor (not necessary on dc motors up to 24 V). With dc motors the wires must be connected to the correct poles. In the electrical installation, arrangements (complying with EN 60335-1) must be made for disconnecting the pump motor from the electrical supply. The pump must be installed so that contact with live parts (connection, possibly windings) is impossible. For pumps with ac motor: We recommend that a fuse is installed in the motor supply circuit; the operating current is given in Data Sheet. For pumps with ac motor: We recommend that a fuse is installed in the motor supply circuit; the operating current is given in Data Sheet. EMC-compatible Installation (for N828/838 DC) The Tests: Magnetic field with energy-technical frequency Electromagnetic HF field, amplitude-modulated Electromagnetic HF field, pulse-modulated Discharging of static electricity High frequency, asymmetric Fast transients were not carried out, cause the products do not contain electronic modules, which can be affected by these tests. The Surge-test can only be passed with additional means, or is not mandatory, if: From EN61000-6-1 technical norm for EMC protection, part 1,10 test demands for EMC protection, table 3, EMC 6
Diaphragm Vacuum Pumps UN828, UN838_I Installation protection, D.C.- power in- and outputs. Remark 3: (quotation) Not to be used with input connections which are foreseen for a connection with a battery or a rechargeable battery which has to be removed or disconnected from the device for the recharge. Devices with a D.C. power input which are foreseen to be operated with an A.C. / D.C. converter have to be tested at an A.C. power input of an A.C. / D.C. converter fixed by the manufacturer. In case the converter was not fixed they have to be tested at an A.C. power input of a typical (usual) A.C. / D.C. converter. The test is applicable for D C power inputs which are foreseen for a permanent connection to cables which are longer than 10 m. Pneumatic Remove the protection plugs from the port threads. The accessories silencer, and hose connectors (if existing) are screwed into the port threads. Connect the suction and pressure lines. For flow direction see marking on the pump head or data sheet. Arrange the suction and pressure lines so that condensate cannot run into the pump (sloping lines). For vacuum pumps, the exhaust gases must be safely disposed. 7
Operation Diaphragm Vacuum Pumps UN828, UN838_I 4. Operation The pumps must not be used in areas where there is a danger of explosion. Specific safety instructions for the media being handled must be observed. If combustible media are used: Hazard of fires and explosions due to excessively high media temperature. Be aware that the pumps are not designed to be explosion-proof. Make sure the temperature of the medium is always sufficiently below the ignition temperature of the medium, to avoid ignition or explosion. This also applies for unusual operational situations. Note that the temperature of the medium increases when the pump compresses the medium. Hence, make sure the temperature of the medium is sufficiently below the ignition temperature of the medium, even when it is compressed to the maximum permissible operating pressure of the pump. The maximum permissible operating pressure of the pump is stated in the technical specifications (section 10). If necessary, consider any external sources of energy, such as radiation, that may add heat to the medium. In case of doubt, consult the KNF customer service. Before pumping a medium, the compatibility of materials of pump head, diaphragm and valves with the medium must be checked (for pump materials: see section 10). The pump must not start against pressure or vacuum. When it is switched on the pressure in the suction and pressure lines must be atmospheric. This must be so even when the pump restarts after the power has been cut off for a short period. The maximum permissible operating pressure (see section 10) must not be exceeded. To prevent the maximum permissible operating pressure being exceeded, restriction or control of the air or gas flow should only be carried out in the suction line. If restriction or control of the air or gas flow is made on the pressure side ensure that the maximum permissible operating pressure is not exceeded. When the pump is at a standstill the inlet and exhaust must be at normal atmospheric pressure. For vacuum pumps, the exhaust gases must be safely disposed 8
Diaphragm Vacuum Pumps UN828, UN838_I Operation For pumps that may be employed as vacuum pump and compressor must not be used to produce vacuum and pressure at the same time. For pumps with a thermal switch: when the operation of the pump is interrupted by the thermal switch, it will re-start automatically after cooling down. Take all care necessary to prevent this leading to a dangerous situation. Diaphragm and valve plates/sealings are the only parts subject to wear. Wear is usually indicated by a drastic reduction in the pneumatic performance. When replacing parts proceed as described in section 5. Ambient conditions: see section 1.3. 9
Servicing Diaphragm Vacuum Pumps UN828, UN838_I 5. Servicing 5.1. AN_-versions (versions with pump head made of aluminium) Diaphragm and valve plates/sealings are the only parts of the pump subject to wear. They are simple to change. Always change valve plates/sealings and diaphragm at the same time. If the diaphragm and the valve plates/sealings are not changed at the same time the nominal performance of the pump is not guaranteed after the servicing. If aggressive, toxic or other types of gases hazardous to health have been pumped please observe: 1. Clean the pump and its components before servicing. 2. Ensure that the service personnel is not subject to a health hazard during diaphragm and valve plate changes. Apply the necessary safety measures (example: the use of protective gloves). 3. Ensure that the discarded parts and materials are safely and correctly disposed of. Parts and tools required Part/tool 1 Service Set* Phillips screwdriver no. 2 Phillips screwdriver no. 1 (only for dc pumps N 828) Felt-tip marker Tab. 2: Parts/tools *according to section 8 Change the structured diaphragm and valve plates/sealings in the following sequence: a.) Preparatory steps b.) Remove pump head c.) Change structured diaphragm d.) Change valve plates/sealings e.) Refit pump head f.) Final steps 10
Diaphragm Vacuum Pumps UN828, UN838_I Servicing Fig. 5: One-headed pump (UN828 ANI) Specification Pos. Description Fig. 4: Section for AN_-version (pump heads made from aluminium) 1 Housing 2 Intermediate plate 3 Ribbed plate 4 Screw 5 Cover 6 Valve plate/sealing 7 Structured diaphragm 8 Diaphragm spacer 9 Connecting rod 10 Counter weight M: Mark Proceed as follows (see figs. 4 and 5): a.) Preparatory steps 1. Remove the pump from the source of electrical power. Make sure the pump is voltage-free and secure it. 2. Only for models with dc motors (no cooling fan): Remove cover (5) from pump housing after loosening the four screws. On these models, which have no fan, where reference is made to turning or holding the cooling fan, the necessary operations must be carried out by turning or holding the counterweight (10). b.) Remove pump head 1. Mark the position of the ribbed plate (3), intermediate plate (2), and housing (1) relative to each other by a drawing line (M) with a felt-tip marker. This helps avoid incorrect assembly later. 2. Undo the 4 screws (4) in the ribbed plate and lift the ribbed plate with the intermediate plate off the pump housing. c.) Change structured diaphragm 1. Turn the fan to bring the structured diaphragm (7) to top dead center. 11
Servicing Diaphragm Vacuum Pumps UN828, UN838_I 2. Lift the edge of the structured diaphragm and, gripping it on opposite sides, unscrew it by turning counter-clockwise. 3. Take the diaphragm spacer(s) (8) off the threaded portion of the structured diaphragm and retain it/them. 4. Check that all parts are free from dirt and clean them if necessary (see section 6. Cleaning). 5. Put the diaphragm spacer(s) (8) on the thread of the new structured diaphragm. 6. Turn the fan until the connecting rod (9) is at top dead center. 7. Screw the new structured diaphragm (7), complete with diaphragm spacer(s) (8) into the connecting rod (9) (clockwise) and tighten it by hand. d.) Change valve plates/sealings 1. Separate the ribbed plate (3) from intermediate plate (2). 2. Remove the valve plates/sealings (6) from the intermediate plate. 3. Check that the valve seats in the ribbed plate and intermediate plate are clean; if scratches, distortion, or corrosion are evident on these parts they should be replaced. 4. Lay the new valve plates/sealings (6) in the recesses in the intermediate plate (2). The valve plates/sealings for suction and pressure sides are identical, as are upper and lower sides of the plates. 5. Check that the valve plates/sealings are not deformed by moving them gently sideways in their recesses. e) Refit pump head 1. Turn the fan to bring the structured diaphragm (7) to top dead center. 2. Place the intermediate plate (2) with valve plates/sealings (6), and ribbed plate (3) on the housing, in the position indicated by the marking (M). 3. Check that the ribbed plate (3) is centred by moving it gently sideways. 4. Gently tighten the screws (4), evenly and diagonally. 5. Turn the fan to check that the pump rotates freely. 6. Turn the fan again to bring the structured diaphragm (7) to top dead center. 7. Now tighten screws (4) firmly diagonally (torque: 3.5 Nm). f.) Final steps 1. In the case of dc version (no cooling fan): refix the cover (5) to housing (1). 12
Diaphragm Vacuum Pumps UN828, UN838_I Servicing 2. Connect the pump to the electrical supply. If you have any questions about servicing call our technical adviser (see last page for contact telephone number). 5.2. KN_-versions (versions with pump head made of plastic) Diaphragm and valve plates/sealings are the only parts of the pump subject to wear. They are simple to change. Always change valve plates/sealings and diaphragm at the same time. In the case of models with two pump heads service both heads at the same time. If the diaphragm is not changed in borh heads at the same time or the diaphragm and the valve plates/sealings are not changed at the same time, the nominal performance of the pump is not guaranteed after the servicing. If aggressive, toxic or other types of gases hazardous to health have been pumped please observe: 1. Clean the pump and its components before servicing. 2. Ensure that the service personnel is not subject to a health hazard during diaphragm and valve plate changes. Apply the necessary safety measures (example: the use of protective gloves). 3. Ensure that the discarded parts and materials are safely and correctly disposed of. For the two-headed pump N 838.1.2 KNE: Except for the preparatory and final steps, perform and finish all work on one pump head before working on the second pump head. Parts and tools required Part/tool 1 Service Set* Phillips screwdriver no. 2 Phillips screwdriver no. 1 (only for dc pumps N 828) Small screw driver Felt-tip marker Tab. 3: Parts/tools *according to section 8 Change the structured diaphragm and valve plates/sealings in the following sequence: a.) Preparatory steps b.) Remove pump head c.) Change structured diaphragm 13
Servicing Diaphragm Vacuum Pumps UN828, UN838_I d.) Change valve plates/sealings e.) Refit pump head f.) Final steps Fig. 6: Pump head KN_-versions (pump head made from plastic) Specification Pos. Description 1 Cover 2 Intermediate plate 3 Ribbed plate 4 Screw 5 Housing 6 Valve plate/sealing 7 Structured diaphragm 8 Diaphragm spacer 9 Screw* 10 Screw cap* 11 Disk spring 12 Washer 13 Pneumatic connection hose M Markierung Fig. 7: Two-headed pump (N 838.1.2 KNE) * UN828KN_: 2x * UN838KN_: 1x 14
Diaphragm Vacuum Pumps UN828, UN838_I Servicing Proceed as follows (see figs. 6 and 7): a.) Preparatory steps 1. Remove the pumps from the source of electrical power. Make sure the pump is voltage-free and secure it. 2. Only for models with dc motors (no cooling fan) and for pump UN838.1.2KNI: Remove cover (1) from pump housing after loosening the four screws. On these models, which have no fan, where reference is made to turning or holding the cooling fan, the necessary operations must be carried out by turning or holding the counterweight (10) (see fig. 4). 3. Only for UN838.1.2KNI: At one pump head, remove both pneumatic connection hoses (13). b.) Remove pump head 1. Mark the position of the ribbed plate (3), intermediate plate (2) and housing (5) relative to each other by a drawing line with a felt-tip marker. This helps avoid incorrect assembly later. 2. Undo the 4 screws (4) in the ribbed plate (3) and lift the ribbed plate with the intermediate plate off the pump housing. c.) Change structured diaphragm 1. Turn the fan to bring the structured diaphragm (7) to top dead center. 2. Lift the edge of the structured diaphragm and, gripping it on opposite sides, unscrew it by turning counter-clockwise. 3. Take the diaphragm spacer(s) (8) off the threaded portion of the structured diaphragm and retain it/them. 4. Check that all parts are free from dirt and clean them if necessary (see section 6. Cleaning). 5. Put the diaphragm spacer(s) (8) on the thread of the new structured diaphragm. 6. Turn the fan until the connecting rod (connecting part between motor shaft and structured diaphragm) is at top dead centre. 7. Screw the new structured diaphragm (7), complete with diaphragm spacer(s) (8) into the connecting rod (clockwise) and tighten it by hand. d.) Change valve plates/sealings 1. Use a small screwdriver to remove the screw cap (10) (UN828KN_: two screw caps (10)) on the pump head and then undo the screw(s) (9). 2. Separate the ribbed plate (3) from intermediate plate (2). 15
Servicing Diaphragm Vacuum Pumps UN828, UN838_I 3. Remove the valve plates/sealings (6) from the intermediate plate. 4. Check that the valve seats in the ribbed plate and intermediate plate are clean; if scratches or distortion corrosion are evident on these parts they should be replaced. 5. Lay the new valve plates/sealings (6) in the recesses in the intermediate plate (2). The valve plates/sealings for suction and pressure sides are identical, as are upper and lower sides of the valve plates/sealings. 6. Check that the valve plates/sealings are not deformed by moving them gently sideways in their recesses. 7. Place the ribbed plate (3) on the intermediate plate (2), in the position indicated by the marking (M). 8. Check that the ribbed plate (3) is centred by moving it gently sideways. 9. Join the ribbed plate (3) and the intermediate plate (2) by tightening the two screws (9) (N 838 KN_: screw (9)) with disk spring (11) and washer (12). For orientation of disk spring see fig. 6. Torque for tightening the screw(s): UN828 : 25 Ncm; UN838 : 35 Ncm. 10. Install the screw cap(s) (10). e.) Refit pump head 1. Turn the fan to bring the structured diaphragm (8) to top dead center. 2. Place the pump head (consisting of intermediate plate (2) with valve plates/sealings (6), and ribbed plate (3) on the housing, in the position indicated by the marking (M). 3. Gently tighten the screws (4), evenly and diagonally. 4. Turn the fan to check that the pump rotates freely. 5. Turn the fan again to bring the structured diaphragm to top dead center. 6. Now tighten screws (4) firmly (torque: 3.5 Nm). Only UN838.1.2KNI and UN8381.2.KNDCB: Repeat operations b.), c.) d.) and e.) for the second pump head. 16
Diaphragm Vacuum Pumps UN828, UN838_I Cleaning f.) Final steps 1. Only in the case of dc versions (no cooling fan) and UN838.1.2KNI: refix the cover (1). 2. Only UN838.1.2KNI: Place both pneumatic connection hoses (13) on the hose connectors at the pump head. 3. Connect the pump to the electrical supply. If you have any questions about servicing call our technical adviser (see last page for contact telephone number). 6. Cleaning When changing structured diaphragm(s) and valve plates/sealings, inspect all parts for dirt before assembling the pump head and clean them if necessary. As far as possible, clean the parts with a dry cloth. Solvents should not be used as they can attack the plastics, and synthetic rubber parts. If a compressed air line is available, blow the parts out with it. 17
Trouble Shooting Diaphragm Vacuum Pumps UN828, UN838_I 7. Trouble Shooting Before working on the pump isolate the power supply securely, then check that the lines are not live. The following tips for fault-finding are best employed in the sequence shown. Pump produces no flow Thermal switch has opened due to over-heating. Disconnect pump from mains and allow to cool. Trace cause of over-heating and eliminate it. Connections or lines are blocked An external valve is closed, or a filter blocked. Liquid (condensate) has collected in the pump head. Let the pump run for a few minutes pumping air (if necessary for safety reasons: pumping an inert gas.) Install the pump at the highest point in the system. Diaphragms or valve plates/sealings are worn. Section 5 Servicing. Flow, pressure, or vacuum too low Compare the actual performance with the figures in section 10 or the data sheet. There is pressure on the pressure side, and at the same time vacuum, or a pressure above atmospheric, on the suction side. The pump is not designed for this condition. Liquid (condensate) has collected in the pump head. Let the pump run for a few minutes pumping air (if necessary for safety reasons: pumping an inert gas.) Install the pump at the highest point in the system. The cross-section of pneumatic lines, or connected components is too small, or they are restricted. To measure the performance, disconnect the pump from the system (small diameter tubing or a valve can significantly affect performance). There is a leak at a connector, in a line, or in the pump head. Diaphragm or valve plate/sealings are worn, or dirt is in the head: Section 5 Servicing. 18
Diaphragm Vacuum Pumps UN828, UN838_I Trouble Shooting If the pump does not operate properly and you cannot find any of the above faults, send it to the KNF Service Department. In order for KNF to repair the pump, the customer must provide a statement on the media which were pumped and on pump cleaning. Please fill out the corresponding KNF form, and submit it together with the pump. A sample statement for copying can be found in section 11 of these Operating and Installation Instructions. 19
Spare parts and accessories Diaphragm Vacuum Pumps UN828, UN838_I 8. Spare parts and accessories A Service Set contains all replacement parts needed for one complete service; for one-headed pumps: 1 structured diaphragm and 2 valve plates/sealings; for two-headed pumps: 2 structured diaphragms and 4 valve plates/sealings. Service Set for UN828ANI UN828KNI UN828ANDC UN828KNDC UN828KNDCB Order-No. 073466 Service Set for UN838ANI UN838KNI UN838ANDC UN838KNDC UN838KNDCB Order-No. 074287 Service Set for UN838.1.2KNI UN838.1.2KNDCB Order-No. 208596 Accessories Description Order No. Silencer/Filter 072233 Hose connector (straight) for all pump types except N 838.1.2 KNI: 1/8NPTM-3/8HID 073896 20
Diaphragm Vacuum Pumps UN828, UN838_I 9. Tables Pump type Max. permissible operating pressure (bar g) Ultimate vacuum (mbar abs.) UN828ANI 1 100 28 UN828KNI 1 100 28 UN828ANDC 1 100 27 UN828KNDC 1 100 27 UN838ANI 0.5 100 34 UN838KNI 0.5 100 34 UN838ANDC 0.5 100 32 UN838KNDC 0.5 100 32 UN838.1.2KNI 0.5 90 42 Delivery rate* (l/min) at atm. pressure Tab. 5: Pneumatic Data *Litre at STP Pump type Material* Pump head Structured diaphragm UN828ANI Aluminium alloy EPDM FPM UN828KNI PPS EPDM FPM UN828ANDC Aluminium alloy EPDM FPM UN828KNDC PPS EPDM FPM UN838ANI Aluminium alloy EPDM FPM UN838KNI PPS EPDM FPM UN838ANDC Aluminium alloy EPDM FPM UN838KNDC PPS EPDM FPM Valve plates/ sealings UN838.1.2KNI PPS EPDM EPDM Tab. 6: Pump Materials *Material abbreviations according DIN ISO 1629 and 1043.1 21
Product Return Diaphragm Vacuum Pumps UN828, UN838_I KNF Neuberger, Inc 2 Black Forest Rd Trenton, NJ 08691-1810 Phone 609-890-8600 Fax 609-890-8323 10. Product Return KNF provides warranty and non-warranty repair services for all products. A Return Material Authorization (RMA) number is required for all product returns. To receive an RMA number, submit a completed Decontamination Declaration form to rma@knf.com The Decontamination Declaration form can obtained from our website or by contacting KNF Technical Services. http://www.knf.com/pdfs/decontamdec.doc Phone: 609-890-8600 Product return instructions will be provided when the RMA is issued. www.knf.com/usa.htm. 22
Diaphragm Vacuum Pumps UN828, UN838_I www.knf.com/usa.htm 23
Benelux Netherlands KNF Verder B.V. Utrechtseweg 4a NL-3451 GG Vleuten Tel. 0031 (0)30 677 92 40 Fax 0031 (0)30 677 92 47 E-mail: info@knf-verder.nl www.knf-verder.nl Benelux Belgium, Luxembourg KNF Verder N.V. Kontichsesteenweg 17 B-2630 Aartselaar Tel. 0032 (0)3 8719624 Fax 0032 (0)3 8719628 E-mail: info@knf.be www.knf.be China KNF Neuberger Trading (Shanghai) Co., Ltd No. 36 Lane 1000 Zhang Heng Road Shanghai 201203, P.R. China Tel. 0086 (0)21 685 965 66 Fax 0086 (0)21 339 006 26 E-mail: info@knf.com.cn www.knf.com.cn Germany KNF Neuberger GmbH Alter Weg 3 D-79112 Freiburg Tel. 0049 (0)7664 5909-0 Fax 0049 (0)7664 5909-99 E-mail: info@knf.de www.knf.de France, Morocco, Algeria KNF Neuberger 4, Bld. d Alsace Z.I. F-68128 Village-Neuf Tel. 0033 (0)389 70 35 00 Fax 0033 (0)389 69 92 52 E-mail: info@knf.fr www.knf.fr KNF worldwide Great Britain KNF Neuberger U.K. Ltd. Avenue 2 Station Lane Industrial Estate Witney Oxon OX28 4FA Tel. 0044 (0)1993 77 83 73 Fax 0044 (0)1993 77 51 48 E-mail: info@knf.co.uk www.knf.co.uk India KNF Pumps + Systems (India) Pvt. Ltd. RAJIV GANDHI INFOTECH PARK Phase 1 Ganga Estate, Survey No. 152/2/2 Above AXIS BANK Hinjewadi Pune 411 057 Tel. 0091 (0)20 640 13 923 0091 (0)20 640 08 923 Fax 0091 (0)20 229 33 923 E-mail: info@knfpumps.in www.knfpumps.in Italy KNF ITALIA S.r.l. Via Flumendosa, 10 I-20132 Milano Tel. 0039 02 27 20 38 60 Fax 0039 02 27 20 38 48 E-mail: info@knf.it www.knf.it Japan KNF Japan Co.Ltd. Chichibu, Bldg. 7F 1-8-6 Shinkawa, Chuo-ku, Tokyo, Japan 104-0033 Tel. 0081 (0)3 3551-7931 Fax 0081 (0)3 3551-7932 E-mail: info@knf.co.jp www.knf.co.jp Korea KNF Neuberger Ltd. Woosan Bldg.RM#202, 336-4, Hwikyung-Dong Dongdaemun-Ku., 130-090, Seoul Tel. 0082 (0)2 959-0255/6 Fax 0082 (0)2 959-0254 E-mail: knf@knfkorea.com www.knfkorea.com KNF product centres Sweden, Denmark, Finland, Norway KNF Neuberger AB Mejerivägen 4, P.O. Box 44060 SE-10073 Stockholm Tel. 0046 (0) 87445113 Fax 0046 (0) 87445117 E-mail: info@knf.se www.knf.se Switzerland Sales KNF Neuberger AG Stockenstrasse 6 CH-8362 Bichelsee-Balterswil Tel. 0041 (0)71 973 993 0 Fax 0041 (0)71 973 993 1 E-mail: knf@knf.ch www.knf.ch Taiwan KNF Neuberger Ltd. 9-2 FL., No., 24, Lane 123, Section 6, Ming Chuan East Road Taipei City, Taiwan Tel. 00886-2-2794-1011 Fax 00886-2-8792-1648 E-mail: knftwn@knftwn.com.tw www.knftwn.com.tw USA, Canada, South America KNF NEUBERGER, INC. Two Black Forest Road Trenton, New Jersey 08691-1810 Tel. 001 (609) 890 86 00 Fax 001 (609) 890 83 23 E-mail: knfusa@knf.com www.knf.com/usa.htm South America Direct Phone: 001 609 649 1010 E-mail: gb@knf.com Product centre for gas pumps: Germany KNF Neuberger GmbH Alter Weg 3 D-79112 Freiburg Phone 0049(0)7664 5909-0 Fax 0049(0)7664 5909-99 E-mail: info@knf.de www.knf.de Product centre for fluid pumps: Switzerland KNF FLODOS AG Wassermatte 2 CH-6210 Sursee Phone 0041(0)41 925 00 25 Fax 0041(0)41 925 00 35 E-mail: info@knf-flodos.ch www.knf-flodos.ch Product centre for micro pumps: Switzerland KNF Micro AG Zelglimatte 1b CH-6260 Reiden Tel. 0041(0)62 787 88 88 Fax 0041(0)62 787 88 99 E-mail: info@knf-micro.ch www.knf-micro.ch