TR & WR TR ST S Y TR SYSTM TTS S ST... 3 ST USTMT... 3 T SRV W R TR UT (M)...3 T SRV W R TR UT (M) :...3 T SRV W R TR UT (M) : Special Repair Requirement...3 URT (M)...3 URT (M) :...3 URT (M) : Special Repair Requirement...4 URT (M) : onfiguration list...5 UT SS... 7 Y TR SYSTM... 7 System...7 omponent arts ocation...8 MT SWT R SYSTM... 9 System iagram...9 System...9 omponent arts ocation...12 S UR SYSTM...13 System iagram...13 System...13 WR SUMT TR SYS- TM...14 System iagram...14 System...14 omponent arts ocation...16 SS SYSTM (M)...17 MM TM...17 MM TM : SUT- unction (M - MM TM)...17 R...18 R : SUT- unction (M - R )...18 RR WW R...20 RR WW R : SUT- unction (M - RR R)...20 UZZR...20 UZZR : SUT- unction (M - UZZ- R)...20 T M...21 T M : SUT- unction (M - T M)...21 MUT RMT T...22 MUT RMT T : SUT- unction (M - MUT RMT T)...22 M...24 M : SUT- unction (M - M)...24 WR...26 WR : SUT- unction (M - WR)...26 SR...27 SR : SUT- unction (M - SR)...27 TT Y...28 TT Y : SUT- unction (M - TT Y)...28 M SW...31 M SW : SUT- unction (M - M SW)...31 M...32 M : SUT- unction (M - M)...32 S S-1
MMU... 32 MMU : SUT- unction (M - MMU)... 32 TTRY SVR... 33 TTRY SVR : SUT- unction (M - TTRY SVR)... 33 TRU... 34 TRU : SUT- unction (M - TRU)... 34 TT M... 35 TT M : SUT- unction (M - TT)... 35 RT WR... 36 RT WR : SUT- unction (M - RT WR)... 36 S UR... 36 S UR : SUT- unction (M - S UR)... 36 R RSSUR MTR... 37 R RSSUR MTR : iagnosis... 37 R RSSUR MTR : SUT- unction (M - R RSSUR MTR)... 38 MT SS... 40 U1000 MM RUT... 40... 40 T ogic... 40 iagnosis rocedure... 40 U1010 TR UT ()... 41 T ogic... 41 iagnosis rocedure... 41 U0415 V S S... 42... 42 T ogic... 42 iagnosis rocedure... 42 2562 W VT... 43 T ogic... 43 iagnosis rocedure... 43 WR SUY RU RUT... 44 iagnosis rocedure... 44 MT SWT UT RUT... 45 iagnosis rocedure... 45 MT SWT UTUT RUT... 47 iagnosis rocedure... 47 U SS... 49 M (Y TR MU)... 49 Reference Value... 49 Wiring iagram - M -... 73 ail-safe... 87 T nspection riority hart... 90 T ndex... 91 SYMTM SS... 94 MT SWT SYSTM SYM- TMS... 94 Symptom Table... 94 RUT... 95 RUTS... 95 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SR"... 95 -V RR... 96 M (Y TR MU)... 96 xploded View... 96 Removal and nstallation... 96 MT SWT... 97 xploded View... 97 Removal and nstallation... 97 S-2
< S ST > ST USTMT S ST ST USTMT T SRV W R TR UT (M) T SRV W R TR UT (M) : :0000000003486680 R RMT When replacing M, save or print current vehicle specification with SUT- configuration before replacement. f R URT can not be used, use the WRT URT - Manual selection after replacing M. TR RMT UT: When replacing M, you must perform WRT URT with SUT-. - omplete the procedure of WRT URT in order. - f you set incorrect WRT URT, incidents might occur. - onfiguration is different for each vehicle model. onfirm configuration of each vehicle model. When replacing M, perform the system initialization (TS). T SRV W R TR UT (M) : Special Repair Requirement :0000000003486681 1.SV V ST SUT- onfiguration erform R URT to save or print current vehicle specification. Refer to S-3, "U- RT (M) : ". f R URT can not be used, use the WRT URT - Manual selection after replacing M. >> T 2. 2.R M Replace M. Refer to S-96, "xploded View". >> T 3. 3.WRT V ST SUT- onfiguration erform WRT URT - onfig file or WRT URT - Manual selection to write vehicle specification. Refer to S-4, "URT (M) : Special Repair Requirement". >> T 4. 4.TZ M (TS) erform M initialization. (TS) S >> WR URT (M) URT (M) : :0000000003486682 Vehicle specification needs to be written with SUT- because it is not written after replacing M. S-3
< S ST > onfiguration has three functions as follows ST USTMT unction R URT WRT URT - Manual selection WRT URT - onfig file Reads the vehicle configuration of current M. Saves the read vehicle configuration. Writes the vehicle configuration with manual selection. Writes the vehicle configuration with saved data. Manual setting item: tems which need selection by vehicle specifications utomatic setting item: tems which are written in automatically (Setting can not be changed) UT: When replacing M, you must perform WRT URT with SUT-. omplete the procedure of WRT URT in order. f you set incorrect WRT URT, incidents might occur. onfiguration is different for each vehicle model. onfirm configuration of each vehicle model. ever perform WRT URT except for new M. URT (M) : Special Repair Requirement 1.WRT M ST SUT- onfiguration Select URT of M. :0000000003486683 When writing saved data>> T 2. When writing manually>> T 3. 2.RRM WRT URT - SUT- onfiguration erform WRT URT - onfig file. >> WR 3.RRM WRT URT - MU ST SUT- onfiguration 1. Select WRT URT - Manual selection. 2. dentify the correct model and configuration list. Refer to S-5, "URT (M) : onfiguration list". 3. onfirm and/or change setting value for each item. UT: Thoroughly read and understand the vehicle specification. ncorrect settings may result in abnormal control of U. 4. Select STT. UT: Make sure to select STT even if the indicated configuration of brand new M is same as the desirable configuration. f not, configuration which is set automatically by selecting vehicle model can not be memorized. 5. When MM S, select. >> T 4. 4.RT onfirm that each function controlled by M operates normally. >> WR S-4
< S ST > ST USTMT URT (M) : onfiguration list :0000000003486684 UT: Thoroughly read and understand the vehicle specification. ncorrect settings may result in abnormal control of U. XT R MX tems MU STT TM : tems which confirm vehicle specifications Setting value UT T WT WTUT TR WT WTUT T WT: With daytime running light system WTUT: Without daytime running light system V /U WT WTUT UT R WT WTUT TT M R WTUT M2 WTUT: Without vehicle security system M2: With vehicle security system -Y WT WTUT R SSR WT WTUT ey ob Type tems UT STT TM M7 M9 Setting value M7: With automatic back door system M9: Without automatic back door system / U UT R M WT T RR M WT ven on a vehicle without rear fog lamp. t displays WT. TRSMSS T with S TMS WT TR RSSUR 230ka TR SW (T) M1 M U S U M VRT M2 T R M4 RR WR M1 ZR SW TY M1 M TR M1 Trunk/lass atch select lass atch ven on a vehicle without glass hatch. t displays lass atch. WM T ST WTUT WM T TMR M1 RR WR WT TRU T UTUT M2 R S TY M2 R W UT WTUT WM T TMR2 M1 S R MX S-5
< S ST > ST USTMT tems MU STT TM : tems which confirm vehicle specifications Setting value UT T WT WTUT TR WTUT V /U WT WTUT UT R WT WTUT TT M R WTUT M2 T WTUT: Without vehicle security system M2: With vehicle security system ZR SW TY M1 -Y WT WTUT R SSR WT WTUT ey ob Type M7 M9 M7: With automatic back door system M9: Without automatic back door system tems UT STT TM Setting value / U UT R M WT T RR M WT ven on a vehicle without rear fog lamp. t displays WT. TRSMSS T with S TMS WTUT TR SW (T) M1 M U S U M VRT M2 T R M4 RR WR M1 M TR M1 Trunk/lass atch select lass atch ven on a vehicle without glass hatch. t displays lass atch. WM T ST WTUT WM T TMR M1 RR WR WT TRU T UTUT M2 R S TY M2 R W UT WTUT WM T TMR2 M1 S-6
< UT SS > UT SS Y TR SYSTM System Y TR SYSTM :0000000003441350 UT M (ody ontrol Module) controls the various electrical components. t inputs the information required to the control from communication and the signal received from each switch and sensor. M has combination switch reading function for reading the operation status of combination switches (light, turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical components. t also has the signal transmission function as the passed point of signal and the power saving control function that reduces the power consumption with the ignition switch. M is equipped with the diagnosis function that performs the diagnosis with SUT- and various settings. M TR UT ST System ombination switch reading system Signal buffer system ower consumption control system uto light system Turn signal and hazard warning lamp system eadlamp system arking, license plate and tail lamps system ront fog lamp system xterior lamp battery saver system aytime running light system nterior room lamp control system Step lamp system nterior room lamp battery saver system ront wiper and washer system Rear wiper and washer system Warning chime system oor lock system ack door opener system (Without ntelligent ey system) utomatic back door system utomatic drive positioner system issan Vehicle mmobilizer System (VS) - TS (With ntelligent ey system) S-9, "System iagram" S-13, "System iagram" S-14, "System iagram" X-13, "System iagram" Reference X-17, "System iagram" (Xenon type headlamp) X-197, "System iagram" (alogen type headlamp) X-8, "System iagram" (Xenon type headlamp) X-191, "System iagram" (alogen type headlamp) X-19, "System iagram" (Xenon type headlamp) X-199, "System iagram" (alogen type headlamp) X-15, "System iagram" (Xenon type headlamp) X-195, "System iagram" (alogen type headlamp) X-21, "System iagram" (Xenon type headlamp) X-201, "System iagram" (alogen type headlamp) X-11, "System iagram" (Xenon type headlamp) X-193, "System iagram" (alogen type headlamp) -5, "System iagram" -8, "System iagram" WW-5, "WT R SSR : System iagram" (With rain sensor) WW-9, "WTUT R SSR : System iagram" (Without rain sensor) WW-14, "System iagram" WS-5, "WR M SYSTM : System iagram" -18, "System iagram" (With ntelligent ey system) -388, "System iagram" (Without ntelligent ey system) -396, "System iagram" -48, "System iagram" -13, "UTMT RV STR SYSTM : System iagram" S-18, "System iagram" S S-7
< UT SS > Y TR SYSTM issan Vehicle mmobilizer System (VS) - TS (Without ntelligent ey system) Vehicle security system anic alarm Rear window defogger system System omponent arts ocation ngine start function Warning function Remote keyless entry system (Without ntelligent ey system) oor lock function ack door function Remote keyless entry ntelligent ey system/engine start system function ey reminder function Warning function ngine start function ower window system Retained accessory power (R) system Tire pressure monitor system (TMS) - R RSSUR M- TR S-244, " STRT UT : System iagram" S-248, "WR UT : System " S-23, "System iagram" (With ntelligent ey system) S-253, "System iagram" (Without ntelligent ey system) -4, "WT S SYSTM : System iagram" (With S system) -6, "WTUT S SYSTM : System iagram" (Without S system) -392, "System iagram" -22, "TT Y SYSTM : System iagram" W-7, "System iagram" W-7, "System " WT-8, "System iagram" Reference :0000000003441351 M0897ZZ 1. M. ehind of combination meter S-8
< UT SS > MT SWT R SYSTM MT SWT R SYSTM System iagram :0000000003441352 System M0901 :0000000003441353 UT M reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the status of each switch. M is a combination of 5 output terminals (UTUT 1-5) and 5 input terminals (UT 1-5). t reads a maximum of 20 switch status. MT SWT MTRX ombination switch circuit S M0902 ombination switch UT-UTUT system list System UTUT 1 UTUT 2 UTUT 3 UTUT 4 UTUT 5 UT 1 R WSR R WR W TUR TUR R UT 2 R WR R WR T SS M 1 UT 3 T VUM 1 RR WSR M 2 M S-9
MT SWT R SYSTM < UT SS > System UTUT 1 UTUT 2 UTUT 3 UTUT 4 UTUT 5 UT 4 RR WR T T VUM 3 UT T T M UT 5 T VUM 2 RR WR R eadlamp has a dual system switch. MT SWT R UT M reads the status of the combination switch at 10 ms interval normally. M0067 M reads the status of the combination switch at 60 ms interval when M is controlled at low power consumption mode. M operates as follows and judges the status of the combination switch. - UT 1-5 outputs the voltage waveforms of 5 systems simultaneously. - t operates the transistor on UTUT side in the following order: UTUT 5 4 3 2 1. - The voltage waveform of UT corresponding to the formed circuit changes according to the operation of the transistor on UTUT side if any (1 or more) switches are. - t reads this change of the voltage as the status signal of the combination switch. peration xample n the following operation example, the combination of the status signals of the combination switch is replaced as follows: UT 1-5 to 1-5 and UTUT 1-5 to -. xample 1: When a switch (TUR R switch) is turned M0068 S-10
< UT SS > MT SWT R SYSTM The circuit between UT 1 and UTUT 5 is formed when the TUR R switch is turned. M0903 M detects the combination switch status signal 1 when the signal of UTUT 5 is input to UT 1. M judges that the TUR R switch is when the signal 1 is detected. xample 2: When some switches (turn R switch, front wiper switch) are turned The circuits between UT 1 and UTUT 5 and between UT 1 and UTUT 3 are formed when the TUR R switch and R WR W switch are turned. M0904 M detects the combination switch status signal 1 when the signals of UTUT 3 and UTUT 5 are input to UT 1. M judges that the TUR R switch and R WR W switch are when the signal 1 is detected. WR TRMTTT ST M judges the wiper intermittent dial 1-7 by the status of T VUM 1, 2 and 3 switches. Wiper intermittent dial position Switch status T VUM 1 T VUM 2 T VUM 3 1 2 3 4 5 S S-11
MT SWT R SYSTM < UT SS > Wiper intermittent dial position 6 7 or details of wiper intermittent dial position, refer to WW-5, "WT R SSR : System " (with rain sensor) or WW-9, "WTUT R SSR : System " (without rain sensor). omponent arts ocation Switch status T VUM 1 T VUM 2 T VUM 3 :0000000003441354 M0898ZZ 1. ombination switch 2. M. ehind of combination meter S-12
< UT SS > S UR SYSTM System iagram S UR SYSTM :0000000003441355 M1014 System :0000000003441356 UT M has the signal transmission function that outputs/transmits each input/received signal to each unit. Signal transmission function list Signal name nput gnition switch signal gnition switch signal oor switch signal ush-button ignition switch (push switch) ny door switch M /R () river seat control unit () utomatic back door control unit () ombination meter () M /R () river seat control unit () V control unit () il pressure switch signal M /R () ombination meter () Stop lamp switch signal Stop lamp switch TM () nputs the push-button ignition switch (push switch) signal and transmits the ignition switch status judged with M via communication. nputs the door switch signal and transmits it via communication. Transmits the received oil pressure switch signal via communication. nputs the stop lamp switch 1 signal and stop lamp switch 2 signal, and transmits it via communication. S S-13
WR SUMT TR SYSTM < UT SS > WR SUMT TR SYSTM System iagram :0000000003441357 M0906 System :0000000003441358 UT M incorporates a power saving control function that reduces the power consumption according to the vehicle status. M switches the status (control mode) by itself with the power saving control function. t performs the sleep request to each unit (M /R, combination meter, driver seat control unit and automatic back door control unit) that operates with the ignition switch. ormal mode (wake-up) - communication is normally performed with other units - ach control with M is operating properly communication sleep mode ( sleep) - transmission is stopped - ontrol with M only is operating ow power consumption mode (M sleep) - ow power consumption control is active - transmission is stopped W WR SUMT TR WT M M reduces the power consumption with the following operation in the low power consumption mode. The reading interval of the each switches changes from 10 ms interval to 60 ms interval. Sleep mode activation M receives the sleep-ready signal (ready) from M /R and combination meter via communication. M transmits the sleep wake up signal (sleep) to each unit when all of the sleep conditions are fulfilled. ach unit stops the transmission of communication with the sleep wake up signal. M is in communication sleep mode. M is in the low power consumption mode and perform the low power consumption control when all of the M sleep conditions are fulfilled with sleep condition. S-14
< UT SS > Sleep condition WR SUMT TR SYSTM sleep condition Receiving the sleep-ready signal (ready) from all units gnition switch: Vehicle security system and panic alarm: ot operation Warning chime: ot operation ntelligent ey system buzzer: ot operation Stop lamp switch: ey slot (card switch) status: o change Turn signal indicator lamp: ot operation xterior lamp: oor lock status: o change SUT- communication status: ot communication Meter display signal: on-transmission oor switch status: o change Rear window defogger: uto back door: ot operation M sleep condition nterior room lamp battery saver: Time out R system: ower window switch communication: o transmission ush-button ignition switch illumination: issan Vehicle mmobilizer System (VS) - TS: ot operation Remote keyless entry receiver communication status: o communication Tire pressure monitor system (TMS) - R RSSUR M- TR: Stop indicator lamp: ot operation indicator lamp: ot operation Wake-up operation M changes from the low power consumption mode to the communication sleep mode when the any of the M wake-up conditions is fulfilled. ly the control with M is activated. M transmits the sleep wake up signal (wake up) to each unit when any of the wake-up conditions is fulfilled. t changes from the low power consumption mode or the communication sleep mode to the normal mode. ach unit starts the transmission of communication with the sleep wake up signal. n addition, the combination meter transmits the wake up signal to M via communication to report the communication start. Wake-up condition M wake-up condition ower window switch communication: Receiving Remote keyless entry receiver communication: Receiving wake-up condition Receiving the sleep-ready signal (ot-ready) from any units ey slot (key switch):, ush-button ignition switch (push switch): azard switch: SS switch:, T M switch: river door switch:, assenger door switch:, Rear R door switch:, Rear door switch:, ack door switch:, river door request switch: assenger door request switch: ack door request switch: Stop lamp switch: S S-15
WR SUMT TR SYSTM < UT SS > omponent arts ocation :0000000003441359 M0899ZZ 1. ombination meter 2. M /R 3. M 4. river seat control unit 5. utomatic back door control unit. ngine room (). ehind of combination meter. ackside of the seat cushion (driver seat). ash side lower (assenger side) S-16
< UT SS > SS SYSTM (M) MM TM SS SYSTM (M) MM TM : SUT- unction (M - MM TM) T TM SUT- performs the following functions via communication with M. iagnosis mode Work Support Self iagnostic Result iag Support Monitor ata Monitor ctive Test cu dentification onfiguration unction SYSTM T M can perform the following functions for each system. t can perform the diagnosis modes except the following for all sub system selection items. System :0000000003441360 hanges the setting for each system function. isplays the diagnosis results judged by M. Monitors the reception status of communication viewed from M. Refer to SUT- operation manual. The M input/output signals are displayed. The signals used to activate each device are forcibly supplied from M. The M part number is displayed. Read and save the vehicle specification. Write the vehicle specification when replacing M. Sub system selection item iagnosis mode : pplicable item Work Support ata Monitor ctive Test oor lock R Rear window defogger RR R Warning chime UZZR nterior room lamp timer T M Remote keyless entry system MUT RMT T* 1 xterior lamp M Wiper and washer WR * 2 Turn signal and hazard warning lamps SR ntelligent ey system ngine start system R TR* 3 TT Y ombination switch M SW ody control system M VS - TS MMU nterior room lamp battery saver TTRY SVR ack door opener system TRU Vehicle security system TT M R system RT WR Signal buffer system S UR TMS TMS (R RSSUR MTR) S *1: t models with ntelligent ey system this item is displayed, but is not used. *2: t models with rain sensor this mode is displayed, but is not used. S-17
< UT SS > *3: This item is displayed, but is not used. SS SYSTM (M) RZ RM T () The M records the following vehicle condition at the time a particular T is detected, and displays on SUT-. SUT screen item ndication/unit Vehicle Speed km/h Vehicle speed of the moment a particular T is detected do/trip Meter km Total mileage (dometer value) of the moment a particular T is detected Vehicle ondition R S> S> > > RU> R>RU RU>URT > > > >R >S >S ounter 0-39 RU R ower position status of the moment a particular T is detected R : SUT- unction (M - R ) M SUT- UT SUT- performs the following functions via communication with M. While turning M status from low power consumption mode to normal mode (ower supply position is ) While turning M status from low power consumption mode to normal mode (ower supply position is.) While turning power supply position from to While turning power supply position from to While turning power supply position from RU to (Vehicle is stopping and selector lever is except position.) While turning power supply position from R to RU (rom cranking up the engine to run it) While turning power supply position from RU to (mergency stop operation) While turning power supply position from to While turning power supply position from to While turning power supply position from to While turning power supply position from to R While turning M status from normal mode (ower supply position is.) to low power consumption mode While turning M status from normal mode (ower supply position is.) to low power consumption mode ower supply position is (gnition switch with steering is locked.) ower supply position is (gnition switch with steering is unlocked.) ower supply position is (gnition switch ) ower supply position is (gnition switch with engine stopped) ower supply position is RU (gnition switch with engine running) ower supply position is R (t engine cranking) The number of times that ignition switch is turned after T is detected The number is 0 when a malfunction is detected now. The number increases like 1 2 3...38 39 after returning to the normal condition whenever ignition switch. The number is fixed to 39 until the self-diagnosis results are erased if it is over 39. :0000000003729363 S-18
< UT SS > SS SYSTM (M) iagnosis mode WR SURT T MTR TV TST WR SURT Monitor item R -U ST UTMT R S- T UTMT R U ST UTMT /U ST T MTR unction hanges the setting for each system function. The M input/output signals are displayed. The signals used to activate each device are forcibly supplied from M. Selective unlock function mode can be changed to operate (WT) or not operate (WTUT) with this mode. utomatic door lock function mode can be selected from the following in this mode. V S: ll doors are locked when vehicle speed more than 24km/h (15M) R: ll doors are locked when shifting the selector lever from position to other than the position utomatic door unlock function mode can be selected from the following in the mode. M 1: ll doors are unlocked when the power supply position is changed from to M 2: ll doors are unlocked when shifting the selector lever from any position other than the to position M 3: river side door is unlocked when the power supply position is changed from to M 4: river side door is unlocked when shifting the selector lever from any position other than the to position utomatic door lock/unlock function mode can be selected from the following in this mode. : non-operational Unlock ly: door unlock operation only ock ly: door lock operation only ock/unlock: lock/unlock operation Monitor tem RQ SW-R RQ SW-S RQ SW-/TR R SW-R R SW-S R SW-RR R SW-R R SW- SW U SW Y Y -SW Y Y U-SW TV TST ontents ndicated [/] condition of door request switch (driver side). ndicated [/] condition of door request switch (passenger side). ndicated [/] condition of back door request switch. ndicated [/] condition of front door switch (driver side). ndicated [/] condition of front door switch (passenger side). ndicated [/] condition of rear door switch R. ndicated [/] condition of rear door switch. ndicated [/] condition of back door switch. ndicated [/] condition of lock signal from door lock unlock switch. ndicated [/] condition of unlock signal from door lock unlock switch. ndicated [/] condition of lock signal from door key cylinder. ndicated [/] condition of unlock signal from door key cylinder. S S-19
< UT SS > SS SYSTM (M) Test item R RR WW R RR WW R : SUT- unction (M - RR R) ata monitor This test is able to check door lock/unlock operation. The all door lock actuators are locked when on SUT- screen is touched. The all door lock actuators are unlocked when U on SUT- screen is touched. The door lock actuator (driver side) is unlocked when R U on SUT- screen is touched. The door lock actuator (passenger side) is unlocked when S U on SUT- screen is touched. The door lock actuator (rear and R) is unlocked when TR U on SUT- screen is touched. :0000000003729373 Monitor tem RR SW US SW This is displayed even when it is not equipped. ndicates [/] condition of push switch. TV TST UZZR Test tem RR R This test is able to check rear window defogger operation. Rear window defogger operates when on SUT- screen is touched. UZZR : SUT- unction (M - UZZR) :0000000003729374 SUT- T TMS Test item iagnosis mode UZZR ata Monitor ctive Test isplays M input data in real time. peration of electrical loads can be checked by sending driving signal to them. T MTR isplay item [Unit] US SW [/] U S-R [/] V S 1 [m/h] Y SW-ST [/] T M SW [/] R SW [/] R SW-R [/] Status of push button ignition switch judged by M. Status of unlock sensor judged by M. Value of vehicle speed signal received from S actuator and electric unit (control unit) with communication line. Status of key slot judged by M. Status of each switch judged by M using the combination switch readout function. Status of front fog lamp switch judged by M. Status of driver side door switch judged by M. S-20
< UT SS > TV TST isplay item [Unit] Y WR M ST T WR TST RST WR T WR M T M SS SYSTM (M) T M : SUT- unction (M - T M) WR SURT The key warning chime operation can be checked by operating the relevant function (/). The seat belt warning chime operation can be checked by operating the relevant function (/). The regist warning chime operation can be checked by operating the relevant function (/). The light warning chime operation can be checked by operating the relevant function (/). :0000000003729375 0093 Service item Setting item Setting ST / -U T * With the interior room lamp timer function Without the interior room lamp timer function M 2 7.5 sec. RM M TMR ST M 3* 15 sec. Sets the interior room lamp time. (Timer operating time) M 4 30 sec. M 1 0.5 sec. M 2* 1 sec. RM M TM ST M 3 2 sec. Sets the interior room lamp gradual brightening time. M 4 3 sec. M 5 0 sec. M 1 0.5 sec. M 2 1 sec. RM M TM ST M 3 2 sec. Sets the interior room lamp gradual dimming time. M 4* 3 sec. M 5 0 sec. M 1* nterior room lamp timer activates with synchronizing all doors. R M TMR ST nterior room lamp timer activates with synchronizing the driver door M 2 only. *: actory setting T MTR S S-21
< UT SS > SS SYSTM (M) RQ SW-R [/] RQ SW-S [/] US SW [/] Y SW-ST [/] R SW-R [/] R SW-S [/] R SW-RR [/] R SW-R [/] R SW- [/] SW [/] U SW [/] Y Y -SW [/] Y Y U-SW [/] R SW [/] R- [/] R-U [/] Monitor item [Unit] The switch status input from request switch (driver side) The switch status input from front request switch (passenger side) The switch status input from push-button ignition switch ey switch status input from key slot The switch status input from front door switch (driver side) The switch status input from front door switch (passenger side) The switch status input from rear door switch R The switch status input from rear door switch The item is indicated, but not monitored. ock switch status received from door lock/unlock switch by power window switch serial link Unlock switch status received from door lock/unlock switch by power window switch serial link ock switch status received from key cylinder lock/unlock switch by power window switch serial link Unlock switch status received from key cylinder lock/unlock switch by power window switch serial link The switch status input from back door switch ock signal status received from remote keyless entry receiver Unlock signal status received from remote keyless entry receiver TV TST T M Test item peration ST M TST U M TST MUT RMT T s the interior room lamp control signal to turn map lamp and personal lamp (Map lamp switch is in R position). Stops the interior room lamp control signal to turn map lamp and personal lamp. s the step lamp control signal to turn step lamp. Stops the step lamp control signal to turn step lamp. The item is displayed, but cannot be tested. MUT RMT T : SUT- unction (M - MUT RMT T) M SUT- UT SUT- performs the following functions via communication with M. :0000000003729366 S-22
< UT SS > iagnosis mode WR SURT T MTR TV TST T MTR Monitor tem R SW-R R SW-S R SW-RR R SW-R R SW- SW U SW R- R-U R-TR/ R- R-/W R-M Y Y -SW Y Y U-SW Y Y SW-TR TV TST Test item T M U M TST R SR R TRU/SS T TRU/ R UTMT R SS SYSTM (M) unction hanges the setting for each system function. The M input/output signals are displayed. The signals used to activate each device are forcibly supplied from M. ondition ndicates [/] condition of front door switch (driver side). ndicates [/] condition of front door switch (passenger side). ndicates [/] condition of rear door switch R. ndicates [/] condition of rear door switch. ndicates [/] condition of back door switch. ndicates [/] condition of door lock and unlock switch. ndicates [/] condition of door lock and unlock switch. ndicates [/] condition of signal from keyfob. ndicates [/] condition of U signal from keyfob. ndicates [/] condition of TRU signal from keyfob. ndicates [/] condition of button of keyfob. ndicates [/] condition of /W W signal from keyfob. ndicates [/] condition of M signal from keyfob. ndicated [/] condition of lock signal from door key cylinder. ndicated [/] condition of unlock signal from door key cylinder. This item is displayed, but cannot be monitored. This test is able to check interior room lamp operation. The interior room lamp will be activated after on SUT- screen is touched. This item is displayed, but cannot be tested. This test is able to check door lock/unlock operation. The all door lock actuators are locked when on SUT- screen is touched. The all door lock actuators are unlocked when U on SUT- screen is touched. The door lock actuator (driver side) is unlocked when R U on SUT- screen is touched. The door lock actuator (passenger side) is unlocked when S U on SUT- screen is touched. The door lock actuator (rear and R) is unlocked when TR U on SUT- screen is touched. This test is able to check flasher operation [/R/]. This test is able to check horn operation [/]. This test is able to check trunk lid opener actuator open operation. This actuator opens when on SUT- screen is touched. This test is able to check back door opener actuator open operation. This actuator opens when on SUT- screen is touched. This test is able to check back door opener actuator open operation. This actuator opens when on SUT- screen is touched. S S-23
< UT SS > WR SURT SS SYSTM (M) M Test item R -U ST R R ST ZR M ST UT ST RM ST W W ST M : SUT- unction (M - M) WR SURT Selective unlock function mode can be changed to operate (WT) or not operate (WTUT) with this mode. nswer back function (horn) mode can be changed in this mode. or the detail of the setting. nswer back function (hazard) mode can be changed in this mode. M1: on-operation M2: ock (non-operation) Unlock (blink once) M3: ock (blink towice) Unlock (non-operation) M4: ock (blink towice) Unlock (blink once) uto door lock time can be changed in this mode. M 1: 1 minute M 2: 5 minutes anic alarm button pressing time on keyfob remote control button can be selected from the following with this mode. M1: 0.5 sec. M2: 1.5 sec. M3: on-operation Unlock button pressing time on keyfob button can be selected from the following with this mode. M 1: 3 sec. M 2: on-operation M 3: 5 se :0000000003729377 *: actory setting T MTR Service item Setting item Setting TTRY SVR ST Y ST USTM /T ST- T * M 1* M 2 M 3 M 4 M 5 M 6 M 7 M 8 M 1* With the exterior lamp battery saver function Without the exterior lamp battery saver function 45 sec. Without the function 30 sec. 60 sec. 90 sec. 120 sec. 150 sec. 180 sec. ormal Sets delay timer function timer operation time. (ll doors closed) M 2 More sensitive setting than normal setting (Turns earlier than normal operation.) M 3 More sensitive setting than M 2 (Turns earlier than M 2.) M 4 ess sensitive setting than normal setting (Turns later than normal operation.) S-24
< UT SS > US SW [/] TV TST Monitor item [Unit] STT [Stop/Stall/rank/Run] V S 1 [km/h] Y SW-ST [/] TUR S R [/] TUR S [/] T M SW [/] M SW [/] M SW1 [/] M SW2 [/] SS SW [/] UT T SW [/] R SW [/] RR SW [/] R SW-R [/] R SW-S [/] R SW-RR [/] R SW-R [/] R SW- [/] T SSR [V] SS SYSTM (M) The switch status input from push-button ignition switch The engine status received from M with communication The value of the vehicle speed received from combination meter with communication ey switch status input from key slot ach switch status that M detects from the combination switch reading function The item is indicated, but not monitored. The switch status input from front door switch (driver side) The switch status input from front door switch (passenger side) The switch status input from rear door switch R The switch status input from rear door switch The item is indicated, but not monitored. The value of exterior brightness voltage input from the optical sensor S T M Test item peration Transmits the position light request signal to M /R with communication to turn the tail lamp. Stops the position light request signal transmission. S-25
< UT SS > SS SYSTM (M) M R M RR M YTM RU T RR M M S WR WR : SUT- unction (M - WR) WR SURT Test item peration *:actory setting Work support item is not indicated when the vehicle with rain sensor. T MTR i ow R Transmits the high beam request signal with communication to turn the headlamp (). Transmits the low beam request signal with communication to turn the headlamp (). Stops the high & low beam request signal transmission. Transmits the front fog light request signal to M /R with communication to turn the front fog lamp. Stops the front fog light request signal transmission. The item is indicated, but cannot be tested. The item is indicated, but cannot be tested. The item is indicated, but cannot be tested. The item is indicated, but cannot be tested. Service item Setting item WR S STT * :0000000003729379 With vehicle speed (ront wiper intermittent time linked with the vehicle speed and wiper intermittent dial position) Without vehicle speed (ront wiper intermittent time linked with the wiper intermittent dial position) US SW [/] Monitor tem [Unit] V S 1 [km/h] R WR [/] R WR W [/] R WSR SW [/] R WR T [/] R WR ST [/] The switch status input from push-button ignition switch. The value of the vehicle speed signal received from combination meter with communication. ach switch status that M judges from the combination switch reading function. ront wiper motor (stop position) status received from M /R with communication. S-26
< UT SS > SS SYSTM (M) Monitor tem [Unit] T VUM [1 7] RR WR [/] RR WR T [/] RR WSR SW [/] RR WR ST [/] TV TST ach switch status that M judges from the combination switch reading function. ach switch status that M judges from the combination switch reading function. Rear wiper motor (stop position) status input from the rear wiper motor. SR SR : SUT- unction (M - SR) WR SURT *: actory setting Test item peration R WR RR WR T MTR i o T Transmits the front wiper request signal () to M /R with communication to operate the front wiper operation. Transmits the front wiper request signal () to M /R with communication to operate the front wiper operation. Transmits the front wiper request signal (T) to M /R with communication to operate the front wiper T operation. Stops transmitting the front wiper request signal to stop the front wiper operation. s the voltage to operate the rear wiper motor. Stops the voltage to stop. Service item Setting item Setting ZR SWR ock ly* Unlk ly ock/unlk With locking only With unlocking only With locking/unlocking Without the function :0000000003729378 Sets the hazard warning lamp answer back function when the door is lock/unlock with the request switch or the key fob. S RQ SW-R [/] RQ SW-S [/] US SW [/] TUR S R [/] TUR S [/] Monitor item [Unit] The switch status input from the request switch (driver side) The switch status input from the request switch (passenger side) The switch status input from the push-button ignition switch ach switch status that M detects from the combination switch reading function S-27
< UT SS > ZR SW [/] R- [/] R-U [/] R- [/] Monitor item [Unit] SS SYSTM (M) The switch status input from the hazard switch ock signal status received from the remote keyless entry receiver Unlock signal status received from the remote keyless entry receiver anic alarm signal status received from the remote keyless entry receiver TV TST SR TT Y Test item peration TT Y : SUT- unction (M - TT Y) M SUT- UT SUT- performs the following functions via communication with M. R s the voltage to blink the right side turn signal lamps. s the voltage to blink the left side turn signal lamps. Stops the voltage to turn the turn signal lamps. :0000000003729364 iagnosis mode WR SURT S- RSUTS T MTR TV TST unction hanges the setting for each system function. isplays the diagnosis results judged by M. The M input/output signals are displayed. The signals used to activate each device are forcibly supplied from M. WR SURT Monitor item RM T R UT ST /U Y -Y STRT Y -Y TRU/SS T RM ST W W ST t can be checked whether ntelligent ey code is registered or not in this mode. uto door lock time can be changed in this mode. M 1: 1 minute M 2: 5 minutes M 3: 30 seconds M 4: 2 minutes oor lock/unlock function by door request switch (driver side, passenger side and back door) mode can be changed to operate () or not operate () in this mode. ngine start function mode can be changed to operate () or not operate () with this mode. uzzer reminder function mode by back door request switch can be changed to operate () or not operate () with this mode. anic alarm button pressing time on ntelligent ey remote control button can be selected from the following with this mode. M 1: 0.5 sec. M 2: on-operation M 3: 1.5 sec. Unlock button pressing time on ntelligent ey button can be selected from the following with this mode. M 1: 3 sec. M 2: on-operation M 3: 5 sec. S-28
< UT SS > SS SYSTM (M) Monitor item TRU Y - TT Y WR T Y UT ZR SWR S -Y S -Y U SRT R UTUT S T SS R WT YSS S- RSUT Refer to S-91, "T ndex". T MTR This item is displayed, but cannot be supported. ntelligent ey low battery warning mode can be changed to operate () or not operate () with this mode. ey reminder function mode can be changed to operate () or not operate () with this mode. azard reminder function mode can be selected from the following with this mode. Y: oor lock operation only U Y: oor unlock operation only /U: ock/unlock operation : on-operation uzzer reminder function (lock operation) mode by door request switch (driver side and passenger side) can be selected from the following with this mode. orn chirp: Sound horn uzzer: Sound ntelligent ey warning buzzer : on-operation uzzer reminder function (unlock operation) mode by door request switch can be changed to operate () or not operate () with this mode. Starter motor can operate during the times below. 70 msec 100 msec 200 msec This function allows inside key antenna self-diagnosis. orn reminder function mode by ntelligent ey button can be changed to operate () or not operate () with this mode. Monitor tem RQ SW -R RQ SW -S RQ SW -RR RQ SW -R S-29 ondition ndicates [/] condition of door request switch (driver side). ndicates [/] condition of door request switch (passenger side). This item is displayed, but cannot be monitored. This item is displayed, but cannot be monitored. RQ SW -/TR ndicates [/] condition of back door request switch. US SW ndicates [/] condition of push-button ignition switch. RY2 -/ ndicates [/] condition of ignition relay 2. RY- This item is displayed, but cannot be monitored. U SW R SW 1 R SW 2 T/ SW ST / SW S/ - S/ -U S/ RY -/ U S -R US SW -M This item is displayed, but cannot be monitored. ndicates [/]* condition of brake switch power supply. ndicates [/] condition of brake switch. ndicates [/] condition of position. ndicates [/] condition of or position. ndicates [/] condition of steering lock unit (). ndicates [/] condition of steering lock unit (U). ndicates [/] condition of ignition switch. ndicates [/] condition of driver door U status. ndicates [/] condition of push-button ignition switch. S
< UT SS > SS SYSTM (M) RY1 -/ ndicates [/] condition of ignition relay 1. T SW -M ndicates [/] condition of position. ST -M ndicates [/] condition of or position. ST -MT ndicates [/] condition of position. ST -MT ndicates [/] condition of position. STT ndicates [ST/STRT/R/RU] condition of engine states. S/ -M ndicates [/] condition of steering lock unit (). S/ U-M ndicates [/] condition of steering lock unit (U). S/ RY-RQ ndicates [/] condition of steering lock relay. V S 1 isplay the vehicle speed signal received from combination meter by numerical value [m/h]. V S 2 isplay the vehicle speed signal received from S or V or VT by numerical value [m/h]. R STT-R ndicates [/RY/U] condition of driver side door status. R STT-S ndicates [/RY/U] condition of passenger side door status. ndicates [ST/RST] condition of key. RMT STRT ndicates [ST/RST] condition of engine start possibility. RMT R STRT This item is displayed, but cannot be monitored. Y SW -ST TR/T MTR R- R-U R-TR/ Monitor tem R- R-/W R-M R U1 R U2 *: is displayed when brake pedal is depressed while brake switch power supply is. TV TST ndicates [/] condition of key slot. This item is displayed, but cannot be monitored. ndicates [/] condition of signal from ntelligent ey. ndicates [/] condition of U signal from ntelligent ey. This item is displayed, but cannot be monitored. ndicates [/] condition of button of ntelligent ey. ndicates [/] condition of /W W signal from ntelligent ey. ndicates [/] condition of M signal from ntelligent ey. When remote keyless entry receiver receives the signal transmitted while operating on ntelligent ey, the numerical value start changing. This item is displayed, but cannot be monitored. ondition Test item TTRY SVR W RMT W ST S UZZR UTS UZZR TR This test is able to check interior room lamp operation. The interior room lamp will be activated after on SUT- screen is touched. This test is able to check power window down operation. The power window down will be activated after on SUT- screen is touched. This test is able to check warning chime in combination meter operation. Take away warning chime sounds when T UT on SUT- screen is touched. ey warning chime sounds when Y WR on SUT- screen is touched. position warning chime sounds when R WR on SUT- screen is touched. warning chime sounds when WR on SUT- screen is touched. This test is able to check ntelligent ey warning buzzer operation. The ntelligent ey warning buzzer will be activated after on SUT- screen is touched. This test is able to check warning lamp operation. Y Warning lamp illuminates when Y on SUT- screen is touched. Y Warning lamp flashes when Y on SUT- screen is touched. S-30
< UT SS > SS SYSTM (M) T M TRU/SS T SR R T2 R M SW Test item SW UM TR TR T Y ST UM UTMT R UTMT S R M SW : SUT- unction (M - M SW) T MTR This test is able to check interior room lamp operation. The interior room lamp will be activated after on SUT- screen is touched. This test is able to check meter display information ngine start information displays when on SUT- screen is touched. ngine start information displays when on SUT- screen is touched. ey warning displays when on SUT- screen is touched. Steering lock information displays when RTT on SUT- screen is touched. position warning displays when ST on SUT- screen is touched. ntelligent ey insert information displays when SRT on SUT- screen is touched. ntelligent ey low battery warning displays when TT on SUT- screen is touched. Take away through window warning displays when Y on SUT- screen is touched. Take away warning display when UTY on SUT- screen is touched. position warning display when W on SUT- screen is touched. This test is able to check back door opener actuator open operation. This actuator opens when on SUT- screen is touched. This test is able to check hazard warning lamp operation. The hazard warning lamps will be activated after on SUT- screen is touched. This test is able to check horn operation. The horn will be activated after on SUT- screen is touched. This test is able to check ignition relay operation. The ignition relay will be activated after on SUT- screen is touched. This test is able to check control device power supply ontrol device power is supplied when on SUT- screen is touched. This test is able to check push-ignition switch illumination operation. ush-ignition switch illumination illuminates when on SUT- screen is touched. This item is displayed, but cannot be tested. This test is able to check indicator in push-ignition switch operation. ndicator in push-button ignition switch illuminates when on SUT- screen is touched. This test is able to check indicator in push-ignition switch operation. ndicator in push-button ignition switch illuminates when on SUT- screen is touched. This test is able to check key slot illumination operation. ey slot illumination flash when on SUT- screen is touched. This item is displayed, but cannot be tested. This item is displayed, but cannot be tested. :0000000003441369 S Monitor item [UT] R WR [/] R WR W [/] R WSR SW [/] R WR T [/] R WR ST [/] isplays the status of the R WR switch in combination switch judged by M with the combination switch reading function. isplays the status of the R WR W switch in combination switch judged by M with the combination switch reading function. isplays the status of the R WSR switch in combination switch judged by M with the combination switch reading function. isplays the status of the R WR T switch in combination switch judged by M with the combination switch reading function. isplays the status of the front wiper stop position signal received from M /R via communication. S-31
< UT SS > Monitor item [UT] SS SYSTM (M) T VUM [1-7] RR WR [/] RR WR T [/] RR WSR SW [/] RR WR ST [/] TUR S R [/] TUR S [/] T M SW [/] M SW [/] M SW 1 [/] M SW 2 [/] SS SW [/] UT T SW [/] R SW [/] RR SW [/] M isplays the status of wiper intermittent dial position judged by M with the combination switch reading function. isplays the status of the RR WR switch in combination switch judged by M with the combination switch reading function. isplays the status of the RR WR T switch in combination switch judged by M with the combination switch reading function. isplays the status of the RR WSR switch in combination switch judged by M with the combination switch reading function. isplays the status of the rear wiper stop position signal received from rear wiper motor. isplays the status of the TUR R switch in combination switch judged by M with the combination switch reading function. isplays the status of the TUR switch in combination switch judged by M with the combination switch reading function. isplays the status of the T M switch in combination switch judged by M with the combination switch reading function. isplays the status of the M switch in combination switch judged by M with the combination switch reading function. isplays the status of the M 1 switch in combination switch judged by M with the combination switch reading function. isplays the status of the M 2 switch in combination switch judged by M with the combination switch reading function. isplays the status of the SS switch in combination switch judged by M with the combination switch reading function. isplays the status of the UT T switch in combination switch judged by M with the combination switch reading function. isplays the status of the R switch in combination switch judged by M with the combination switch reading function. The item is indicated, but not monitored. M : SUT- unction (M - M) :0000000003441370 WR SURT MMU tem RST STT VU Return a value set with Work Support of each system to a default value in factory shipment. MMU : SUT- unction (M - MMU) :0000000003729368 T TM SUT- performs the following functions via communication with M. iagnosis mode T MTR TV TST unction The M input/output signals are displayed. The signals used to activate each device are forcibly supplied from M. T MTR S-32
< UT SS > SS SYSTM (M) Monitor item RM RM 4 RM 3 RM 2 RM 1 T 4 T 3 T 2 T 1 US SW Y SW -ST ontent ndicates [YT] at all time. Switch to [] when a registered ntelligent ey is inserted into the key slot. ndicates the number of which has been registered. ndicates [/] condition of push-button ignition switch. ndicates [/] condition of key slot. TV TST TT Test item TTRY SVR TTRY SVR : SUT- unction (M - TTRY SVR) WR SURT TTRY SVR ST This test is able to check security indicator lamp operation. The lamp will be turned on when on SUT- screen touched. Service item Setting item Setting RM M T SV ST * * With the exterior lamp battery saver function Without the exterior lamp battery saver function With the interior room lamp battery saver function Without the interior room lamp battery saver function :0000000003729376 RM M TMR ST *: actory setting T MTR RQ SW-R [/] RQ SW-S [/] RQ SW-RR [/] RQ SW-R [/] US SW [/] Y SW-ST [/] U S-R [/] Monitor item [Unit] M 1* 30 min. Sets the interior room lamp battery saver timer operating M 2 60 min. time. The switch status input from request switch (driver side) The switch status input from front request switch (passenger side) The item is indicated, but not monitored. The switch status input from push-button ignition switch ey switch status input from key slot river door unlock status input from unlock sensor S S-33