ISO 5011 Test Results Certified to the ISO 5011 Air Filtration Standard Replacement Filter for AFE Intake Kit 1994-07 Dodge Ram Cummins 5.9L Diesel S&B Part Number: CR-90021
ISO 5011 Air Filtration Standard AFE Intake Kit Air Filter Comparison S&B Filters CR-90021 Test Number 324 Filter INITIAL RESTRIC. CAPACITY EFFICIENCY Air Flow Net Restriction % Less Restrictive than Mfg. & Part No. ("H2O) (grams) (%) scfm (Inches of H2O) 72-90021AFE Filter #1 4.1 483.9 99.37 0.0 0.000 0.0% S&B Filters 263.7 1.114 10.9% CR-90021 396.9 2.447 7.2% 526.4 4.230 6.6% 656.2 6.506 5.7% 790.0 9.308 4.8% Filter #2 4.4 355.9 99.63 0.0 0.000 AFE 263.3 1.250 72-90021 396.0 2.637 524.4 4.530 658.7 6.902 789.2 9.773 RESTRICTION vs FLOWRATE 8.000 7.000 S&B Filters AFE Avg Restriction (" H2O) 6.000 5.000 4.000 3.000 2.000 1.000 0.000 0.0 100.0 200.0 300.0 400.0 500.0 600.0 700.0 Flow Rate (cfm) ISO 5011 Air Filtration Test Filter Efficiency % ISO 5011 Air Filtration Test Air Flow Summary 100.00 98.00 S&B Filters 99.37 AFE 99.63 AFE Air Filter p/n 72-90021 96.00 S&B Filters Part Number CR-90021 Flows: 94.00 % 6.6% Better Than AFE at rated CFM 7.0% Better Than AFE Across CFM Spectrum 92.00 90.00 88.00 86.00 1 AVERAGE ENVIRONMENTAL CONDITIONS & TEST SPECIFICATIONS Temperature: 70.55 deg F Housing: uni con Relative Humidity: 50.45 % Contaminant: Coarse Baro Pressure: 29.01 mmhg Contam. Lot #: 5457C Test Stand: #1 Dust Feed Rate: 14.73 grams/minute Inlet Size: 3.875 inches Rated Flow: 526 cfm Testing was conducted based on the ISO 5011 Air Filtration Standard.
ISO 5011, Second Edition Performance Testing: Inlet Air Cleaning Equipment for Combustion Engines & Compressors S&B Filters, Inc. 787 South Wanamaker Avenue Ontario, California 91761 (909) 947-0015 (909) 947-0603 www.sbfilters.com ISO 5011Test Results Explanation - Course Test Dust.doc ISO 5011, Second Edition Air Filter or Intake Kit Test Report The test data presented in the following report represents the restriction of airflow, efficiency and dust loading capacity. The filters tested were procured from various distributors or provided by customers. The tests were performed in accordance with ISO 5011. The following were measured in accordance with the test: (1) Pressure Drop for Clean Element, Initial Efficiency and Dust Loading Capacity. The Flow Rate used to conduct the Dust Loading and Capacity test(s) is listed under the Average Environmental Conditions and Test Specifications. PTI ISO Course Test Dust was utilized and the particle data sheet for the batch is attached. The test sequence begins with measuring the pressure drop of a clean filter as a function of the airflow rate which is measured in cubic feet per minute (CFM). Subsequently, the cumulative efficiency and dust loading capacity are measured. The termination point when measuring for capacity is shown at the bottom of the report under the heading Termination ^P. The results of the tests are recorded in the top table and charts shown on the next page. The filters are inspected before and after the tests are performed. The Top Table demonstrates the results of the testing for up to three (3) samples per filter type (part number). The Efficiency represents the amount of dust (contaminants) that was stopped by the filter during each test. The Capacity measures the dust holding capability of the filter. During the test, the filter is loaded with dust until it reaches a terminal pressure drop increase of 10 inches of water (28 H2O for Heavy Duty Vehicles) across the filter element (please refer to the Average Environmental Conditions and Test Specifications at the bottom of the next page to verify the pressure drop utilized on this particular test). The Line Graph shows the pressure drop as a function of the airflow rate for the clean filter(s). The computer controlled test equipment initiates the test at close to zero (0) cubic feet per minute (CFM) and then increases the CFM gradually until the CFM termination point is reached. During the test, the restriction of the filter is measured in inches of water ( H2O) as it relates to the air flow rate (CFM). Visual inspections of filters are performed to insure against dust leakage and manufacturing flaws. The Bar Graph illustrates the cumulative efficiency for the filter(s) tested. Definition of Terms & Test Protocol Restriction Restriction measures how difficult it is for the air to get through the filter and is measured in inches of H2O. Instead of referring to restriction, the industry uses "air flow" to describe the effect of restriction. They say for example, that a High Performance Filter "flows better" than the OEM paper filter. On a line graph, the lower the restriction of a filter the better the air flow. Efficiency Efficiency is measured in % and is the amount of dirt/contaminants that the filter stops from going into the engine. Capacity Capacity is the total amount of contaminants/dirt the filter will hold before reaching its termination point. The termination point is a predefined restriction point that is used as the cut-off point when measuring how much dirt a filter will hold. For typical vehicles, 10 H2O is used at the termination point. For heavy duty trucks, this number is 28 H2O. Note: Testing was conducted based on the ISO 5011 testing standard; however, variances from the actual test procedures may exist. The intent of the testing is to show comparative test results between various products that are intended for similar use. Tests are conducted under a climate controlled environment; however, changes in temperature and humidity between tests may occur which could alter the actual test results.
Determination of Gasoline and Diesel Engine Air Consumption CFM Calculator: Enter Data in Blue Shaded Areas Engine Displacement (cubic inches) 358.1 Liters to CID Converter Liters: 5.9 RPM at maximum horse power 2,900 Cubic Inches: 358.1 Cycle Factor: 2 Enter "2" for 4 Cycle Diesel and Gasoline Vehicle Information Enter "1" for 2 Cycle Diesel and Gasoline Model Year 03'-07' Volumetric Efficiency: 1.75 Make Dodge Naturally Aspirated Gasoline & Diesel Engines Enter "0.8" Model Ram 2500 Super Charged Diesel Engines Enter "1.30" Engine Specs Turbo DSL L6 Turbocharged Diesel Engines Enter "1.75" Based on the information entered above, the estimated CFM of the vehicle at maximum Horse Power is: 526 CYCLE FACTOR Cycle Factor 4 Cycle Diesel and Gasoline Engine 2 2 Cycle Diesel and Gasoline Engine 1 VOLUMETRIC EFFICIENCY Volumetric Efficiency (Approximate) Naturally Aspirated Gasoline & Diesel Engines 0.8 Supercharged Diesel Engines 1.30 Turbocharged Diesel Engines 1.75 Note: The 1.75 volumetric efficiency is applicable only at top governed engine speed under full load conditions. EQUATION The following is a method of determining approximated gasoline and diesel engine air flow requirement: Air Flow (CFM) = Displacement (cubic inches) x RPM x Volumetric Efficiency 1728 Cycle Factor EXAMPLE Information necessary to calculate air consumption: Ford F250 7.3L V8 Diesel Truck 4 cycle, 2800 RPM, 445.5 (cubic inches) displacement, turbocharged Air Flow (CFM) : 445.5 x 2800 x 1.75 = 631 CFM 1728 2 \\Server3\official public folder\iso Test Results - Released (Restricted)\AFE Replacements\72-90021 (S&B CR-90021)\CFM Calculator Dodge 5.9L.xls