Installation Instructions

Installation Instructions SELECTRONIC Integrated Faucet with Above-Deck Mixing CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. Product No.'s & Options Specifications Faucet Installation Electrical Installation Start-up / Maintenance FAQ s / Troubleshooting Parts - -9 9-0 MODEL NUMBERS 70X.0 70X. 70X.0 70X. Certified to comply with ASME A.8. 06 American Standard NOTE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com For Parts, Service, Warranty or other Assistance, please call (8) CRT-TEAM / (8) 78-86 (In Canada: -800-87-069) (In Toronto Area only: -90-06-09) M966 Rev..0 (9/6)

Flexible Selectronic Platform with Universal Sensor Easy installation. All electronics in the spout; nothing below deck User adjustable above-deck mixing uses ceramic disc valve for dependability & long life Mixing handle can be removed for one time temperature setting during installation CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. M966 Rev.. (/) Certified to comply with ASME A.8. 0 American Standard To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com For Parts, Service, Warranty or other Assistance, please call (8) CRT-TEAM / (8) 78-86 (In Canada: -800-87-069) (In Toronto Area only: -90-06-09) MODEL NUMBERS Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.. Installation Instructions. Spout Assembly (less mixing) a. Spout Assembly (mixing). Mounting Kit. " Deck plate (optional, must be ordered separately). Mixing Valve (optional, must be ordered separately) 6. Filter Screen(s) 7. Assembly Parts POWER KITS SOLD SEPARATELY B a s e P r o d u c t DO NOT REMOVE PROTECTIVE FILM FROM SENSOR EYE UNTIL INSTALLATION IS COMPLETE. PRODUCT No.s 70X.0 70X. a DO NOT REMOVE PROTECTIVE FILM FROM SENSOR EYE UNTIL INSTALLATION IS COMPLETE. PRODUCT No.s 70X.0 70X. PWRX Plug-In AC Hard-Wired AC Multi-AC PK00.WRK PK00.PAC PK00.HAC PK00.MAC 6 7 Installation Instructions SELECTRONIC Integrated Faucet with Above-Deck Mixing Product No.'s & Options Specifications Faucet Installation Electrical Installation Start-up / Maintenance FAQ s / Troubleshooting Parts - -9 9-0 70X.0 70X. 70X.0 70X. NOTE TO INSTALLER: Please give this manual to the customer after installation. 70P00 60XTMV070 Deck Plate Mixing Valve M966 Rev..0 (9/6)

Fig. FINISHED WALL OR BACKSPLASH 9mm (7-/) Roughing-in Dimensions CLEARANCE 9mm mm (min) - 7mm (max) (7-/) (" min - " max) 6mm 0mm (6-/) (-/) MOUNTING SURFACE 8mm (-/ ) 66mm ( -/8) 8mm (-/8) Note: All plumbing and electrical wiring must be installed in accordance with applicable codes, regulations and standards. CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. 7mm (8) RECOMENDED CONTROL BOX OR EQUIVALENT BY OTHERS " (0mm) SQ. X -/" (89mm) DEEP CONTROL BOX Hubbel-RACO #6 OR EQUAL (BY OTHERS). /8" COMPRESSION CONNECTORS HARD-WIRED AND MULTI AC 0' MAX. CABLE LENGTH TOOLS REQUIRED; Fig. Fig.. mm Hex Wrench (Included) Adjustable Wrench Plumbers' Putty or Caulking Phillips Screwdriver Tape Measure 0' INSTALLATION SPOUT ASSEMBLY INSTALLATION; Fig. Fig. IMPORTANT: Do not use putty when installing faucet without escutcheon. CAUTION Turn off hot and cold water supplies before beginning. Make sure O-RING () is installed in spout base. If installing ESCUTCHEON () (optional): Apply a bead of putty to bottom edge of ESCUTCHEON PUTTY PLATE (). IMPORTANT: Do not use putty when installing faucet without escutcheon.. Insert supply HOSES (), SHANK () and SENSOR CABLE () (if equipped) through hole in ESCUTCHEON with PUTTY PLATE () and mounting surface. (Make sure PIN (6) is in back).. Assemble RUBBER WASHER (7), BRASS WASHER (8) and THREADED LOCKNUT (9) onto SHANK () from underside of sink or mounting surface. Hand tighten LOCKNUT (9).. Use a screwdriver to tighten SCREWS (0) on LOCKNUT (9). Work your way around LOCKNUT (9), tightening the screws slightly each time until all are snug to ensure even pressure. 7 8 9 0 6 PUTTY (If required) MOUNTING SURFACE (OPTIONAL) TIGHTEN SPIN NUTS IMPORTANT: Do not use sealent on threads M966 Rev..0 (9/6)

ELECTRICAL INSTALLATION Fig. Product Page PWRX (PK00.WRK) Plug-in AC Powe Kit (PK00.PAC) Hard-Wired AC Prower Kit (PK00.HAC) MULTI-AC (PK00.MAC) A PWRX 0-Year Battery Pack Important: The 70 series faucets come with the standard CR-P lithium battery installed in the faucet. No further action required. PWRK VERSION;. Connect PWRX BATTERY PACK () to SENSOR CABLE ().. Secure the connections by installing into CONNECTOR LOCKING DEVICE () as shown. Rotate the END CAPS () to secure the connection within the CONNECTOR LOCKING DEVICE (). BRACKET INSTALLATION. Determine the mounting location of the PWRX BATTERY PACK () by marking center lines as shown.. Place the BRACKET () on the horizontal center line and mark the location of the mounting holes to be drilled.. Using /" diameter drill bit, drill two mounting holes aproximately " deep. 6. Install the two ANCHORS (6) provided into the mounting holes. Use a hammer to lightly tap the ANCHORS (7) into place and flush with the finished wall. HORIZONTAL C/L 7. Place the BRACKET () over the ANCHORS (6) and secure with the SCREWS (7) provided. Do not overtighten. 8. Insert PWRX BATTERY PACK () into BRACKET (). VERTICAL C/L 6 7 M966 Rev..0 (9/6)

B AC VERSIONS (HARD-WIRED / PLUG-IN POWER SUPPLY) ; Fig. Important: Turn off power to outlet or control box. Fig.. Connect PLUG-IN AC POWER SUPPLY () or 0' EXTENSION CABLE () if using HARD-WIRED AC TRANSFORMER (7) to SINGLE AC ADAPTER (). 0' EXTENSION. Connect SENSOR CABLE () to the other terminal of the SINGLE AC ADAPTER ().. Connect PLUG-IN AC POWER SUPPLY () to wall outlet, or connect other end of 0' EXTENSION CABLE () to the HARD-WIRED AC TRANSFORMER (7). FOR HARD-WIRED VERSION;. Make Black and White power line connections to HARD-WIRED AC TRANSFORMER (7) and mount into CONTROL BOX (6). WALL OUTLET 6 BLACK & WHITE POWER CONNECTIONS 7 7 CONNECTOR NOT USED IN THIS INSTALLATION CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. " CONTROL BOX OR EQUIVALENT BY OTHERS (6) Recommended Control Box or Equivalent by others " (0 mm) SQ. x -/" (89 mm) DEEP ELECTRICAL BOX Hubbel-RACO #6 OR EQUAL (BY CONTRACTOR). Fig. Unit # (Already Installed) Unit # Unit # Unit # MAXIMUM OF UNITS PER TRANSFORMER. 0' MAXIMUM CABLE LENGTH BETWEEN UNITS. C MULTI-AC VERSION (DAISY-CHAIN); Fig. Important: Disconnect the first unit s Y-Adapter from power supply before making daisy-chain connections. Note: For Unit # electrical instructions, refer to section B (page ). For subsequent Units, refer to instructions below.... Connect one end of the 0' EXTENSION () to the available terminal of the pervious unit s Y-ADAPTER (), and the other end to the single terminal of the current unit s Y-ADAPTER ().. Connect SENSOR CABLE () to either of the two available terminals of Y-ADAPTER ().. Repeat Steps above for each additional Unit, for a Max. of Units on one AC POWER SUPPLY. M966 Rev..0 (9/6)

Certified to comply with ASME A.8.M 00 American Standard M968808 To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S. customer's e-mail us at: faucetsupport@amstd.com For Parts, Service, Warranty or other Assistance, (In Toronto Area only: -90-0609) D MAKE WATER SUPPLY CONNECTIONS; Fig.. Turn off hot and cold water supplies before beginning. Fig.. Place each SCREEN FILTER () on each wall supply outlet. Be sure that SCREEN FILTER () is inserted in the correct direction. (See Illustration) BULGE SIDE DOWN. Connect HOT FLEXIBLE SUPPLY (marked with red stripe) () to hot water control stop (). Connect COLD FLEXIBLE SUPPLY (marked with blue stripe) () to cold water control stop (). Use adjustable wrench to tighten connections. Do not over tighten. () SCREEN FILTER. Faucet supplies are 8" long from faucet base. COLD Note; If additional supply length is required, installer must purchase those parts separately. HOT IMPORTANT: Do not use sealent on threads Important; If SUPPLY HOSES (, ) are too long, loop as illustrated to avoid kinking. Fig. E INSTALL OPTIONAL MIXING VALVE; Fig. Note: An optional Thermostatic Mixing Valve may be installed (sold separately) on faucets 70X.XX & 70X.XX in addition to Above Deck Mixing valve. See setup diagram Fig.. Tee fitting is not supplied with Faucet or Thermostatic Mixing valve and must be purchased separately. If faucet inlet hoses will not reach water supplies, longer hoses must be purchased separately. Installation Instructions SELECTRONIC Thermostatic Mixing Valve 60XTMV Specifications Installation Adjust Temperature Service Replacement Parts NOTE TO INSTALLER: Please give this manual to the customer after installation. please call -800--90 (In Canada: -800-87-069) TEMPERED WATER SUPPLY Optional Mixing Valve (Sold Separately) COLD WATER For complete detailed installation and operating instructions, see installations instructions (No. M968808) supplied with Thermostatic Mixing Valve. No. M968808 HOT SUPPLY TEE FITTING COLD SUPPLY MAINTENANCE A HAND WASH SENSOR OPERATION; Fig. REMOVE PROTECTIVE FILM FROM SENSOR EYE WHEN INSTALLATION IS COMPLETE. When the Sensor detects a user, the water immediately starts to flow. Water flow will stop. seconds after user is out of sensor range. This Comfort delay allows the user to comfortably move their hands without the water turning off. As a precaution, a Safety Timer will turn off the water, after the sensor has been blocked for 9 seconds. The water will stay off until the blockage is removed from the detection zone. The Comfort and Safety time settings can be adjusted using the Optional Remote Control (60XRCT). Fig. DETECTION ZONE PROTECTIVE FILM M966 Rev..0 (9/6)

B CHANGE SENSOR RANGE; (Factory set at 6") Fig.,,, & a Fig.. Remove the FAUCET SPOUT () by unthreading the LEVER SCREW () and pulling off the LEVER HANDLE (). Unthread the FAUCET SPOUT SCREW () at the back of the FAUCET. Pull FAUCET SPOUT () up and off. Fig.. REPLACE REMOVE. Disconnect the BLACK POWER SUPPLY CONNECTOR () and reconnect. Fig... While the SENSOR CONTROL LED () is blinking slowly, place your hand - in. (.-0.8mm) in front of the sensor. Fig... When the LED stops blinking and stays "ON", move your hand to the desired position and hold in place until the LED begins to blink again. Fig. a.. Once the SENSOR CONTROL LED () begins to blink again, remove your hand from the detection zone. When the flashing stops, the detection distance is set. Fig. 6. Replace FAUCET SPOUT () and LEVER HANDLE (). Install LEVER HANDLE SCREW (), FAUCET SPOUT SCREW () and tighten. Fig.. Note: The LEVER HANDLE () can be removed to prevent users from adjusting the water temperature. Replace the LEVER HANDLE () with PLUG BUTTON () as shown. Fig.. Fig. Fig. a "-" (.mm- 0.8mm) UP TO 0" (mm) BLINKING LED BLINKING LED 6 M966 Rev..0 (9/6)

C REPLACE SENSOR; Fig. Fig., 6 & 7.. Remove the FAUCET SPOUT () by unthreading the LEVER SCREW () and pulling off the LEVER HANDLE (). Unthread the FAUCET SPOUT SCREW () at the back of the FAUCET. Pull FAUCET SPOUT () up and off. See Fig. in this section. DISCONNECT WIRE CONNECTIONS. Disconnect both ELECTRICAL CONNECTIONS. Fig... Untighten SENSOR SCREW () with a.mm HEX WRENCH. Remove SENSOR ASSEMBLY () from FAUCET SPOUT (). Remove O-RING (). Remove SENSOR (a) from CARRIER () and replace with new SENSOR (a). Replace O-RING (). Install SENSOR ASSEMBLY () into FAUCET SPOUT (). Tighten SENSOR SCREW (). Fig. 6, 7.. Replace FAUCET SPOUT () and LEVER HANDLE (). Install LEVER HANDLE SCREW (), FAUCET SPOUT SCREW () and tighten. See Fig. in this section. Fig. 6.mm HEX WRENCH Fig. 7 a 7 M966 Rev..0 (9/6)

D CLEAN FILTER SCREEN ON SOLENOID VALVE; Fig. 8 & 9. Remove the FAUCET SPOUT () by unthreading the LEVER SCREW () and pulling off the LEVER HANDLE (). Unthread the FAUCET SPOUT SCREW () at the back of the FAUCET. Pull FAUCET SPOUT () up and off. See Fig. in this section. Fig. 8. Disconnect SENSOR CABLE () from SOLENOID CABLE (). Fig. 8.. Unthread SOLENOID VALVE () from VALVE BODY (). Fig. 9.. Remove FILTER SCREEN () from base of SOLENOID VALVE (). Clean and replace. Fig. 9.. Thread SOLENOID VALVE () into VALVE BODY () and hand tighten. Reconnect SENSOR and SOLENOID CABLES (). Fig. 8. Fig. 9 6. Replace FAUCET SPOUT () and LEVER HANDLE (). Install LEVER HANDLE SCREW (), FAUCET SPOUT SCREW () and tighten. See Fig. in this section. E REPLACE DIVERTER CARTRIDGE; Fig. 0 &. Remove the FAUCET SPOUT () by unthreading the LEVER SCREW () and pulling off the LEVER HANDLE (). Unthread the FAUCET SPOUT SCREW () at the back of the FAUCET. Pull FAUCET SPOUT () up and off. See Fig. in this section. Fig. 0 9 8. Pull out LIMITER STOP () from the VALVE STEM (). Unthread COLLAR NUT () from VALVE BODY (). Fig. 0.. Pull DIVERTER CARTRIDGE () out and replace with new DIVERTER CARTRIDGE (). NOTE: Make sure the two ALIGMENT PINS (6) in the base of the DIVERTER CARTRIDGE () are facing upward. Fig.. Fig. 6. Replace FAUCET SPOUT () and LEVER HANDLE (). Install LEVER HANDLE SCREW (), FAUCET SPOUT SCREW () and tighten. See Fig. in this section. Fig. 8 M966 Rev..0 (9/6)

F CHANGE HOT LIMIT SETTING FROM 9% TO 8%; Fig.. Remove the FAUCET SPOUT () by unthreading the LEVER SCREW () and pulling off the LEVER HANDLE (). Unthread the FAUCET SPOUT SCREW () at the back of the FAUCET. Pull FAUCET SPOUT () up and off. See Fig. in this section. 9. Replace LEVER HANDLE and rotate counter-clockwise to its stop position (00% cold). Remove HANDLE.. Pull out LIMITER STOP () from the VALVE STEM (). 8 SLOT. Rotate LIMITER STOP () 80 degrees and insert back onto VALVE STEM (). ROTATE 80. Replace FAUCET SPOUT () and LEVER HANDLE (). Install LEVER HANDLE SCREW (), FAUCET SPOUT SCREW () and tighten. See Fig. in this section. Fig. SLOT G GENERAL CLEANING; Fig.. Only use a damp, soft cloth to clean the spout and the sensor.. For tougher dirt, use a soft cloth with diluted dish washing detergent. Wipe the area using a wet cloth and dry using a soft cloth. CAUTION Do not scratch the sensor when cleaning. Avoid using any abrasives or harsh detergents or chemicals. Fig. FAQ'S Q: How will I know if the battery needs to be replaced? A: Valve will not open and sensor will continuously blink times interrupted by a pause for up to 7 days. Q: Why has the flow rate of the faucet reduced significantly? A: The filter assembly, flow regulator or areator/spray may be clogged. Check and clean. Refer to Start-up/Maintenance, sections C, D and E. Q: Why doesn t the water flow out of faucet when I'm within the sensor detection zone? A: Battery may need replacement. Check. If sensor continuously blinks times interrupted by pause, replace battery or call (8) CRT-TEAM / (8) 78-86. Q: What is the normal operating pressure range? A: Faucet will operate with supply pressures ranging from 0-80 psi. 9 M966 Rev..0 (9/6)

TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? YES REPEATED DOUBLE FLASH ON SENSOR? NO RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR SECONDS? YES REPLACE SOLENOID NO YES NO NO OPEN EXTERNAL SUPPLY STOPS. CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. WATER IS CONTINUOUSLY RUNNING RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR SECONDS? NO CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. YES REPLACE SOLENOID LOW FLOW ISSUES ARE EXTERNAL SUPPLY STOPS FULLY OPEN? NO FULLY OPEN EXTERNAL SUPPLY STOPS BY TURNING COUNTER CLOCKWISE. YES CHECK FOR BLOCKAGE INSPECT FILTER ASSEMBLY, AERATOR AND SOLENOID VALVE. REMOVE, CLEAN AND INSERT BACK TO ORIGINAL POSITION. HOT LINE FOR HELP For toll-free information and answers to your questions, call: (8) CRT-TEAM / (8) 78-86 Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST Saturday 0:00 a.m. to :00 p.m. EST IN MEXICO 0-800-89-00 IN CANADA -800-87-069 (TORONTO -90-06-09) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of AS America, Inc. 06 To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com 0 M966 Rev..0 (9/6)

M967-0070A. GPM AERATOR M967-0070A 0. GPM AERATOR Appropriate finish code CHROME 00 A9790-0070A VALVE STEM O-RINGS A9070-000A PLUG BUTTON SELECTRONIC Integrated Faucet with Above-Deck Mixing MODEL NUMBERS 70X.0 70X. 70X.0 70X. M98-0070A SOLENOID VALVE M979-0070A DIVERTER CARTRIDGE M978-0070A SPOUT O-RING M9687-000A LEVER ASSEMBLY M967-0070A SENSOR M900C-0070A COLD SUPPLY HOSE M900H-0070A HOT SUPPLY HOSE PWRX PK00.WRK M9060-0070A CONNECTOR LOCKING DEVICE CR-P Lithium Battery 77. Series M906-0070A PWRX BATTERY PACK M96-0070A BRACKET A96-0070A BATTERY 6V CR-P M90-0070A FILTER SCREENS () Plug-In AC PK00.PAC M908-0070A POWER SUPPLY 70P00.00 ESCUTCHEON M9606-0070A MOUNTING KIT M9060-0070A CONNECTOR LOCKING DEVICE Hard-Wired AC PK00.HAC M9060-0070A CONNECTOR LOCKING DEVICE M9099-0070A SINGLE AC ADAPTER M900-0070A POWER SUPPLY M90-0070A 0' EXTENSION M9099-0070A SINGLE AC ADAPTER HOT LINE FOR HELP For toll-free information and answers to your questions, call: (8) CRT-TEAM / (8) 78-86 Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST Saturday 0:00 a.m. to :00 p.m. EST IN MEXICO 0-800-89-00 IN CANADA -800-87-069 (TORONTO -90-06-09) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of AS America, Inc. 06 To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com Multi-AC PK00.MAC M90-0070A 0' EXTENSION M90-0070A MULTI-AC ADAPTER M966 Rev..0 (9/6)