Puddle/Rock Light Kit Installation Manual: for Jeep JK 2 and 4 door 2007-2018 81901 2 light / 81904 dd on Kit - - 2 Light kit 2 Light dd-on Primary Light locations Light installed on Frame 1 x Controller box (81901 only) 1 x RF Remote (81901 only) 2 x Lights/rackets 2 x Rubber Mounting Pads 4 x 3mm bolts/nuts/washers 2 x 4mm bolts/nuts/washers 1 x Wire Splice (81901 only) 5 x Zip ties (81901 only) Coil of wire (81901 only) Sealant Putty (81901 only) 1 x 8 extension (81904 only) lade screw driver 3 mm llen wrench 4 mm llen wrench djustable wrench (For battery terminals) Pliers NOTE: This kit can be installed on any vehicle using the clamp brackets or the included rubber mounts without the clamp brackets. These instructions are for the Jeep JK speci cally but can be used as a guide for installing on any vehicle. dditional lights can be added up to eight. The controller has four standard outputs and a Y adapter is available to split each of the standard four into an additional circuit. Y harness part # 81905, available separately.
PRT : Install the Frame Lights and rackets. Passenger side Pinch weld Outside of vehicle Locate the Front mounting hole position on the vehicle frame. (Fig 1) Locate the rear mounting hole position on the vehicle frame. NOTE: 4 door only (Fig 2) 3 MM Nut Rubber Pad LED Frame Flat Washer 3 mm Screw Light assy Clamp 4 mm olt Hole Stainless racket ssemble the LED lamps onto the Stainless brackets using the included hardware as shown. Pre-assemble the internal clamp to the external bracket by tightening the internal clamp just far enough so the tab keeps it from spinning when the fastener is tightened. (Fig 3) Install the lamp to the vehicle frame by sliding the internal clamp into the desired frame hole (,). Once the tab is inside the frame, slide it back until the complete tab is in contact with the inside of the frame structure and then tighten.(fig 4) racket Mounting Detail ody FRME FRME Front location Rear Location
PRT : Controller Install and Wiring. Figure 5 Figure 6 Carefully remove side panel of dash on passenger side. It is held in place with several clips and can be pulled loose by hand. e careful nut to break the mounting clips. (Fig 5) Locate the 1 dia. hole with the yellow foam in it on the metal bracket inside the dash. Use a blade screwdriver to punch a hole through the foam to the engine bay. (Fig 6) Controller Figure 8 Figure 7 att Yellow Rigid wire + - lack Red With the controller in the engine bay, use the included coil of rigid wire to pull the yellow controller wire through the 1 rewall hole. Straighten the rigid wire and feed it from the inside of the vehicle to the engine bay. Hook on the yellow wire and pull through to the interior. (Fig 8) Install controller on passenger side rewall above battery and connect red wire to positive terminal, and black wire to negative terminal on battery. (Fig 7) 3
PRT : Controller Install and Wiring Cont.. Harness to frame mounted lights Controller att Factory harness Passenger foot well Figure 9 Figure 10 Remove passenger side door sill trim. Figure 12 + - Figure 11 Use the included wire tap to connect the yellow wire from the controller to the Yellow/White wire in the vehicle loom. With tap open slide yellow/white wire in all the way and then close tap on wire. Now install solderless terminal (included) onto yellow wire and plug into tap. (Fig 11) With lights installed on the vehicle frame, run the wires up to the passenger side re wall and connect to controller. Use zip ties to attach wires to appropriate points along the way. (Fig 12) CUTION: e sure wires will not be damaged or melted. 4
PRT C: Final steps. Putty Figure 13 Use included putty to ll around yellow wire where it comes in from engine bay. (Fig 13) Figure 14 Now replace side panel on dash board and trim inside passenger door to complete installation. (Fig 14) PRT D: Functions and Warnings Functions The Yellow/White wire in the factory harness is the interior lamp line and provides the trigger for the Entry/Exit lamps to turn on. Whenever the interior lamp comes on they will turn on as well. This means they will be activated when the locks are activated and when the interior lamps are turned on via the dash switch WRNING: It is illegal in some states to have these lamps on while driving on city streets. e sure to check local regulations. RF Remote The RF Remote controls On and Off functions. It can be used at any time to turn the lights on or off. WRNING: The ignition of the vehicle does not have to be on to activate the lights with the remote. e sure not to leave the lights on when using the remote. The controller has a built in timer that will turn off the lights after two hours in case they are accidentally activated or left on. The lights can be turned on with the remote while driving off road for added visibility in dif cult terrain. They can also be turned on from outside the vehicle with the RF remote from up to 35 feet away. LWYS CHECK LIGHTING FUNCTIONS FTER INSTLLTION. DO NOT DRIVE ON CITY STREETS WITH THE ENTRY LIGHTS ON S THIS IS ILLEGL IN SOME STTES. Warranty details: C is not responsible for product failures if the parts are not installed properly or used in a manor appropriate for the item. C will warrant for manufacturers defects for a period of 30 days from purchase. Returns without an RM will not be accepted. Please contact us before returning a product and we will be happy to work with you to nd solutions. www.britesaber.com dvanced ccessory Concepts Corona, C 951.339.1460 5