Water Heater Feel the drive Thermo Top Evo5+ Parking Heater e 00 058 Installation documentation Mercedes Benz C Class S0, W0 / from model 007 GLK Class X0 / from model 008 Gasoline and Diesel Left-hand drive vehicle Automatic air-conditioning Blue Efficiency / Blue Tec Sport package AMG 950 Not at C 6 AMG Not for GLK 50 CDI WARNING! Hazard warning: Incorrect installation or repair of Webasto heating systems may cause a fire or result in the emission of carbon monoxide, which can be fatal. Serious or fatal injuries can be caused as a result. Specialist company training, technical documentation, specialised tools and equipment are required to install and repair Webasto heating and cooling systems. Only original Webasto parts must be used. For this, also see the catalog of air and water heater accessories from Webasto. NEVER attempt to install or repair Webasto heating or cooling systems if you have not successfully completed the company training and thereby acquired the required technical skills, or if you do not have access to the required technical documentation, tools and equipment needed to carry out correct installation and repairs. ALWAYS follow all Webasto installation and repair instructions and observe all warnings. The initial startup is to be executed with the Webasto Thermo Test Diagnosis. Webasto does not accept any liability for defects and damage that are attributable to installation by untrained staff. Ident. No.: 5959C_EN Fee Euro 0.00 Webasto AG
Mercedes Benz C Class S0, W0 / GLK Class X0 Table of contents Heater/Installation Kit Foreword General instructions Special tools Validity Explanatory Notes on Document 5 Preliminary Work 6 Heater installation location 6 Preparing electrical system 7 Electrical system 8 Fan controller 9 Push button installation Telestart Preparing installation location heater 6 Exhaust gas 7 Fuel 9 Metering pump of 60l fuel tank Metering pump of 80l fuel tank Gasoline fuel stand pipe Diesel fuel standpipe 6 Connecting metering pump 7 Coolant circuit 9 Combustion air 5 Exhaust end section 7 Final Work 8 Heater/Installation Kit Quantity Description Order No.: Delivery scopethermo Top Evo Mercedes Benz C Class 595A S0, W0 / GLK Class X0 Gasoline with Telestart T9 black (sw) or Delivery scopethermo Top Evo Mercedes Benz C Class S0, W0 / GLK Class X0 Gasoline with Telestart T9 black (sw) 5955A Option heater controls to be ordered according to choice: Quantity Description Order No.: Digital timer See price list Telestart T00 HTM black (sw) See price list The installation location of the digital timer/push button should be confirmed with the end customer before installation. When installing a parking heater, we recommend the use of the next larger vehicle battery. Foreword This installation documentation applies to the Mercedes Benz C-Class S0, W0 vehicles - for validity, see page - from model year 007 and later, also GLK Class X0 Gasoline and Diesel from model year 008, assuming technical modifications to the vehicle do not affect installation, any liability claims excluded. Depending on the vehicle version and equipment, modifications may be necessary during installation with respect to this installation documentation. However, where this is the case, the stipulations of this "installation documentation", the "operating instructions" and the "installation instructions" of thethermo Top Evo should be observed. The corresponding rules of technology and any information from the vehicle manufacturer should be observed during the installation work. Note: Due to the lack of available space, the replacement of the bulb of the right front fog light/cornering light is more complicated after the parking heater is installed. The time required for replacement will be increased. Please inform your customers accordingly! General instructions Installation should be carried out according to the general, standard rules of technology. Unless specified otherwise, fasten hoses, lines and wiring harnesses to original vehicle lines and wiring harnesses using cable ties. Sharp edges should be fitted with edge protectors (split-open plastic hose). Spray unfinished body areas, e.g. drilled holes, with anti-corrosion wax (Tectyl 00K, Order No. 9). While installing an IPCU, the corresponding settings are to be checked or adjusted before the installation. Special tools - Torque wrench for.0-0 Nm - Hose clamping pliers - Metric thread-setter kit 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Validity Manufacturer Model Type EG-BE No./ABE Daimler AG C Class W0 e * 00/6 * 0 *... Daimler AG C Class S0 e * 00/6 * 0 *... Daimler AG GLK Class X0 e * 00/6 * 080 *... W 0 Sedan Type Engine model Output in kw Displacement in cm³ C 80 K Gasoline / R 5 796 C 80 CGI Gasoline / R 5 796 C 00 K Gasoline / R 5 796 C 00 CGI Gasoline / R 5 796 C0 Gasoline / R 50 96 C 50 CGI Gasoline / R 50 796 C80 Gasoline / V6 70 996 C 80 Matic Gasoline / V6 70 996 C 00 Gasoline / V6 70 996 C 00 Matic Gasoline / V6 70 996 C 50 Gasoline / V6 00 98 C 50 Matic Gasoline / V6 00 98 C 50 CGI Gasoline / V6 5 98 C 00 CDI Diesel / R 00 C 0 CDI Diesel / R 5 / 50 C 50 CDI Diesel / R 50 C 50 CDI Matic Diesel / R 50 C 0 CDI Diesel / V6 65 987 C 0 CDI Matic Diesel / V6 65 / 70 987 C 50 CDI Diesel / V6 65 / 70 987 C 50 CDI Matic Diesel / V6 65 987 S 0 Station wagon Type Engine model Output in kw Displacement in cm³ C 80 K Gasoline / R 5 796 C 80 CGI Gasoline / R 5 796 C 00 K Gasoline / R 5 796 C 00 CGI Gasoline / R 5 796 C 0 Gasoline / R 50 96 C 50 CGI Gasoline / R 50 796 C 80 Gasoline / V6 70 996 C 80 Matic Gasoline / V6 70 996 C 00 Gasoline / V6 70 996 C 50 Gasoline / V6 00 98 C 50 Matic Gasoline / V6 00 98 C 00 CDI Diesel / R 00 8 C 0 CDI Diesel / R 5 8 C 50 CDI Diesel / R 50 C 50 CDI Matic Diesel / R 50 C 0 CDI Diesel / V6 65 987 C 0 CDI Matic Diesel / V6 65 987 C 50 CDI Diesel / V6 65 / 70 987 C 50 CDI Matic Diesel / V6 65 / 70 987 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 X 0 GLK Type Engine model Output in kw Displacement in cm³ GLK 80 Matic Gasoline / V6 70 996 GLK 50 Matic Gasoline / V6 00 98 GLK 0 CDI Matic Diesel / V6 65 / 70 987 GLK 50 CDI Matic Diesel / V6 65 /70 987 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Explanatory Notes on Document To provide you with a quick overview of the individual working steps, you will find an identification mark on the outside top right corner of the page in question. Mechanical system Electrical system Coolant circuit Fuel Exhaust gas Combustion air Special features are highlighted using the following symbols: Specific risk of injury or fatal accidents. Specific risk of damage to components. Specific risk of fire or explosion. Reference to these, the general installation instructions of the Webasto operating elements and to vehicle-specific documents of the manufacturer Reference to a special technical feature. The arrow in the vehicle icon indicates the position on the vehicle and the viewing angle. All dimensions are in mm! Tightening torque of 5x heater bolts = 8Nm! Tightening torque of 5x5 bolt of water connection piece retaining plate = 7Nm! 5959C_EN 5
Mercedes Benz C Class S0, W0 / GLK Class X0 Preliminary Work WARNING! - Open the fuel tank cap, ventilate the tank. - Close the tank cap again. - Depressurize the cooling system. - Copy the factory number from the original type label to the duplicate type label. - Remove years that do not apply from the duplicate label. - Attach the duplicate label (type label) in the appropriate place. - Remove the windshield wipers. - Remove the coolant reservoir cap. - Remove the dome strut on the left. - Remove entire windshield wiper linkage with engine. - Remove battery with carrier fully (if installed at the right) - Remove engine control device (if installed on the right)) - Remove the battery cover in the engine compartment on the right. - Remove the trim of the passenger compartment fan air inlet - Detach the coolant expansion tank. - Take off the cover off the positive distributor in the engine compartment. - Remove the air intake pipe on the right (V6 only). - Remove the lower engine cover. - Discharge engine coolant according to manufacturer specification - Remove the lower right vehicle trim. - Remove the right-hand wheel. - Remove the right-hand wheel well trim. - Remove the seat bench of the rear bench seat. - Open the right-hand fuel sender service lid. - Detach the fuel-tank sending unit on the right as described in the manufacturer's instructions. - Remove the A/C control panel. - Lift the shift lever cover. - Remove the ashtray or storage compartment with the socket outlet below the A/C control panel. - Remove the A-pillar trim in the footwell on the right. - Remove the front right door sill cover. - Remove the lower right instrument panel trim. - Remove the lower left instrument panel trim. - Remove the front right floor trim. - Loosen right footrest Heater installation location Heater Installation location 5959C_EN 6
Mercedes Benz C Class S0, W0 / GLK Class X0 Preparing electrical system Detach 6mm dia cable shoe Preparing wiring harness of fan control IPCU view on contact side! The pre-programmed settings of both function controls in the vehicle are to be checked and adjusted if necessary. A 5 86 85 E IPCU 86 85 E A Duty cycle: 56-6% Frequency: 00Hz Voltage:.0V Function: High-side IPCU view 5959C_EN 7
Mercedes Benz C Class S0, W0 / GLK Class X0 Electrical system Ground wire Connect ground wire to the original vehicle ground support point with 6mm dia cable shoe. Route wiring harness to heater in corrugated tube of 0mm dia. Wiring harness pass through Drilling of 6mm dia hole at centre of rubber plug! Cable harnesses of engine compartment fuse holder and heater control Do not route wiring harness of metering pump until later together with fuel line on underbody Wiring harness installation diagram Fuse holder of engine compartment Replace F with A fuse. 5mm dia. hole, M5x6 bolt, washers [x], retention plate of fuse holder, nut F+ fuses mounted 5 Plus wire Manufacturer to install different positive support points. Connect power supply of heater to positive terminal (battery or starter cable of positive support point)! 6 5959C_EN 8
Mercedes Benz C Class S0, W0 / GLK Class X0 Fan controller Webasto HG X 5 X F Mercedes 0 5 Wiring diagram F F rt 0,5² rt/ge rt/ge ws GE M 7 rt ² rt/sw 0,5² br 8 0,5² ge 0,5² gn/ws 0,75² 6 A sw 0,5² ws Kl. X0 5 St KB sw St br 86 87 85 0 87a K A 85 86 IPCU bl ² bl ² rt rt LIN-Bus 9 rt br 86 87 85 0 87a K B M M M M br br 0,5² Webasto components Vehicle components Colours and symbols HG TT-Evo heater GE Fan unit rt red X 6-pin heater connector KB A/C control element ws white X -pin heater connector A Socket outlet/lighter sw black X0 -pin connector B Flap positioning module bl blue Heater control F Fuse ge yellow K Fan relay ST Connector, -pin, KB br brown K Additional relay gn green F Fuse, 0A F 0A fuse replaced with A IPCU Pulse width modulator IPCU adjustment values: Duty cycle: 56% Frequency: 00Hz Voltage:.0V X Cutting point Function: High-side Wiring colours may vary. Legend 5959C_EN 9
Mercedes Benz C Class S0, W0 / GLK Class X0 Prepare wiring harness of engine compartment fuse holder in the passenger compartment. Connect red (rt) wire ² and red/black (rt/sw) 0.5² wire soldering connector. Produce connections as shown in wiring diagram. Preparing wiring harness of engine compartment fuse holder 7 6 5 Route wiring harness of engine compartment fuse holder 5 in the foot well on the front passenger side, and secure with cable tie. Produce connections as shown in wiring diagram. Original vehicle stud bolt, original vehicle ground wires Angle bracket M5x6 bolt, washer, flanged nut Base of IPCU 6 Relay base relay base and IPCU base 8 Install green/white (gn/ws) wire 6 in the IPCU/86 base. Produce connections as shown in wiring diagram. Brown (br) wire of wiring harness of engine compartment fuse holder Brown (br) wire 9 of fan controller wiring harness Connecting wiring harnesses 9 Route wiring harness of fan control to centre console and secure with cable tie. Mount K and K relay Plug IPCU Mounting relay [x] and IPCU 0 5959C_EN 0
Mercedes Benz C Class S0, W0 / GLK Class X0 Connection to -pin connector from A/C control element. Produce connections as shown in wiring diagram. White (ws) wire of fan unit Black (sw) wire K/0 White (ws) wire of -pin KB connector Connecting A/C control panel Connection to -pin connector from A/C control element. Produce connections as shown in wiring diagram. 5 Blue (bl) wire K/0 Red (rt) wire of flap positioning module Red (rt) wire of -pin KB connector 5 Blue (bl) wire K/87 Connecting A/C control panel Connection to plug-in connector of socket outlet/lighter. Produce connections as shown in wiring diagram. Red (rt) wire 5 K/86 Pink/yellow (ro/ge) wire Pink/yellow (ro/ge) wire Connection to socket outlet/lighter 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Push button installation Only in connection with Telestart. Use wiring harness extension! WARNING: If the push button cannot be installed in the trim piece due to parts lying behind it, the installation is undertaken according to Figure 9. Removing cover Cover Mount cap nut of push button, align in centre and drill 6mm dia hole in the cover (step drill)! Hole in cover 5 Install push button, align and secure it with cap nut! push button 6 When drilling, watch components located behind. mm dia hole Hole for wiring harness 7 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Cover Mounting cover 8 Alternative installation location Only in connection with Telestart. Use wiring harness extension! mm dia hole, push button push button 9 Telestart Receiver, adhesive tape receiver 0 Antenna antenna 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Preparing installation location 5 Figure shows W0 with daytime running light! Loosen original vehicle bolt at position, and 5. Insert large diameter washer at position 5 between bracket and bumper. Tighten bolts at position and 5. Bend twist protection at position toward rear. Turn cylinder of the headlight cleaning system and fix with cable tie (observe distance between connector of fog light, if available, and bracket of heater). Detaching bracket Remove joint sealer in the area of the holes or on the inner side of the frame side member! 0 5 0 S0 and W0 7 mm dia. hole X0 Hole in frame side member 7 mm dia. hole Figure shows W0 with daytime running light! Mount heater bracket with oblong hole between detached bracket and bumper at position. Original vehicle bolt Mounting heater S0 and W0 When drilling, watch components located behind. M6x0 bolt, flanged nut Loosely mounting heater 5 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 X0 Insert 8 mm shim between bracket of heater and frame side member. M6x5 bolt, 8 mm shim, flanged nut Loosely mounting heater 6 S0, W0 and X0 with daytime running light Copy 7 mm dia. hole pattern Copying hole pattern 7 S0 and W0 with fog light 5 Ensure proper spacing between connector of front fog light and bracket of heater (at least 5mm! Copy 7 mm dia. hole pattern Copying hole pattern 8 X0 with fog light Copy 7 mm dia. hole pattern Copying hole pattern 9 5959C_EN 5
Mercedes Benz C Class S0, W0 / GLK Class X0 Figure shows W0 with daytime running light! Remove heater. For vehicles with fog light, it must be removed for the hole. 7 mm dia. hole [x] Hole in bumper 0 Figure shows W0 with daytime running light! Install horn with original vehicle bolt. M6x5 bolt,pin lock bolt 6 heater Figure shows W0 with daytime running light! Mount bracket of heater on bolt between detached bracket and bumper. Align heater and fasten at position and 6. Tighten original vehicle bolt at position 5. Tighten bolt on retaining strut. heater 5 Flanged nut 6 M6x0 bolt, flanged nut Figure shows X0 with fog light. Mount bracket of heater on bolt between detached bracket and bumper. Insert 8 mm shim between bracket of heater and frame side member at position. Align heater and fasten at position and. Tighten bolt on retaining strut. Flanged nut M6x0 bolt, 8 mm shim, flanged nut heater 5959C_EN 6
Mercedes Benz C Class S0, W0 / GLK Class X0 Exhaust gas Shape exhaust pipe Hose clamp Push on pipe insulation Preassembling exhaust pipe Mount exhaust muffler on exhaust pipe and align relative to hole. Mount wiring harness 5 on heater. 5 Hose clamp Preassembling muffler 5 Cut tab off exhaust end section. Cutting point Preparing exhaust end section 6 Vehicles with daytime running light M6x bolt, spring lockwasher Hose clamp Exhaust end section muffler and end section 7 5959C_EN 7
Mercedes Benz C Class S0, W0 / GLK Class X0 Ensure sufficient distance to neighbouring components, align bracket if necessary. Minimum distance between bracket of daytime running light and muffler at Position must be observed Aligning muffler min. 5mm 8 Vehicles with fog light Ensure sufficient distance to neighbouring components, correct if necessary. S0 and W0 Slide incomplete exhaust end section onto exhaust muffler (5 mm distance between end section and muffler), align and fasten. X0 Slide complete exhaust end section onto exhaust muffler. muffler and end section 9 M6x bolt, spring lockwasher Hose clamp 5959C_EN 8
Mercedes Benz C Class S0, W0 / GLK Class X0 Fuel CAUTION! Open the vehicle's fuel tank cap, ventilate the tank and then re-close the tank lock. Catch any fuel running off with an appropriate container. Install fuel line and metering-pump wiring harness so that they are protected against stone impact. Unless specified otherwise, always fasten using cable ties. Mount the fuel line and wiring harness with rub protection on sharp edges. WARNING! The fuel line and wiring harness are routed to the metering pump in as shown in the wiring harness routing diagram. Pin out connector housing of metering-pump wiring harness before pulling into corrugated tube. 9 mm dia. corrugated tube, wiring harness of metering pump Cable tie Fuel line, 0 mm dia. clamp Moulded hose of heater Connection to heater 0 Degrease adhesive surface for adhesive base. Adhesive base, cable tie Corrugated tube lines Degrease adhesive surface for adhesive base. Adhesive base, cable tie Corrugated tube lines 5959C_EN 9
Mercedes Benz C Class S0, W0 / GLK Class X0 Degrease adhesive surface for adhesive base. Adhesive base [x], cable tie [x] Corrugated tube Cable tie, existing hole lines Degrease adhesive surface for adhesive base. Adhesive base [x], cable tie [x] Fuel line, wiring harness of metering pump lines Distribute retaining clips [0x] evenly along vehicle underbody and insert fuel line and wiring harness of metering pump. lines 5 Fuel line, wiring harness of metering pump Hose section 8x dia Cable tie Original vehicle retaining strap lines 6 5959C_EN 0
Mercedes Benz C Class S0, W0 / GLK Class X0 Metering pump of 60l fuel tank 0 S0 and W0 0 Drill 9. mm dia. hole, mount M6 rivet nut. Rivet nut for metering pump 7 Degrease adhesive surface for adhesive base. M6x5 bolt Wiring harness of dosing pump, connector mounted 90 F moulded hose, 0 mm dia. clamp [x], fuel line Adhesive base, cable tie 5 Mounting of metering pump 6 Metering pump metering pump 6 5 8 X0 5 Drill 9. mm dia. hole, mount M6 rivet nut. 5 Rivet nut for metering pump 9 Degrease adhesive surface for adhesive base. M6x5 bolt Wiring harness of dosing pump, connector mounted 90 F moulded hose, 0 mm dia. clamp [x], fuel line Adhesive base, cable tie 5 Mounting of metering pump 6 Metering pump metering pump 6 5 50 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Metering pump of 80l fuel tank Angle down perforated bracket and drill hole at Position to 8.5mm dia. 75 Preparing perforated bracket 90 6 M6x5 bolt, flanged nut Mounting of metering pump Metering pump Cable tie 5 Perforated bracket 6 80 moulded hose, 0 mm dia. clamp Premounting metering pump 5 5 Install perforated bracket on original vehicle bolt of fuel tank fastening. Paste insulation strip. Wiring harness of dosing pump, connector mounted 90 Moulded hose, 0 mm dia. clamp [x] Fuel line metering pump 5 Gasoline fuel stand pipe Version Remove fuel-tank sending unit in accordance with manufacturer's specifications. Watch drilling chips while drilling! Mount large diameter washer d a = 7.6mm dia, copy 6mm dia hole pattern 6 mm dia. hole Removing fuel 5 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Cut standpipe obliquely! 5 Section, discard Cutting standpipe to size 5 7 6 Observe tightening torque 5 Nm of flanged nut 6 on fuel standpipe 7. Mount.5 mm dia. moulded hose on fuel standpipe 7. 5 Fuel-tank sending unit Standpipe 0 mm dia. clamp 5 8 mm dia. clamp fuel standpipe 55 7 Install fuel-tank sending unit in accordance with manufacturer's specifications. Mount.5 mm dia. hose on fuel standpipe. 6 5 8 mm dia. clamp 5 6x hose (rattle protection) 6 Fuel line 7 0 mm dia. clamp line 56 Version Remove fuel-tank sending unit in accordance with manufacturer's instructions. Remove upper section from lower section in accordance with manufacturer's instructions. Removing fuel 57 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Cut off connection piece flush on underside. Drill 6 mm dia. hole in centre. Removing fuel 58 Insert fuel standpipe in upper section of fuel-tank sending unit. Removing fuel 59 Observe tightening torque 5 Nm of flanged nut on fuel standpipe. Removing fuel 60 Cut standpipe obliquely! Section, discard 60 Cutting standpipe to size 6 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Mount standpipe in.5 mm dia. moulded hose. 0 mm dia. clamp Premounting standpipe 6 Premount standpipe on fuel standpipe and secure with 8 mm dia. clamp. Fuel-tank sending unit standpipe 6 Install fuel-tank sending unit in accordance with manufacturer's specifications. Insert line holder for guiding standpipe in lower section of fuel-tank sending unit. standpipe 6 5 Install fuel-tank sending unit in accordance with manufacturer's specifications. Mount.5 mm dia. moulded hose on fuel standpipe. 8 mm dia. clamp 5 0 mm dia. clamp 6 Fuel line 7 6x hose (rattle protection) line 6 7 65 5959C_EN 5
Mercedes Benz C Class S0, W0 / GLK Class X0 Diesel fuel standpipe Remove fuel-tank sending unit in accordance with manufacturer's specifications. Watch drilling chips while drilling! 6 mm dia. hole Removing fuel 66 Insert fuel standpipe into fuel-tank sending unit. Removing fuel 67 Observe tightening torque 5 Nm of flanged nut on fuel standpipe. Fuel-tank sending unit Removing fuel 68 Cut standpipe obliquely! 55 Discard section Cutting standpipe to size 69 5959C_EN 6
Mercedes Benz C Class S0, W0 / GLK Class X0 6 5 Mount.5 mm dia. moulded hose on fuel standpipe 6. Fuel-tank sending unit Standpipe 0 mm dia. clamp 5 8 mm dia. clamp standpipe 70 Install fuel-tank sending unit in accordance with manufacturer's specifications. Mount 90 moulded hose with.5mm dia on fuel standpipe 5. 7 6 0 mm dia. clamp 8 mm dia. clamp 6 6x hose (rattle protection) 7 Fuel line fuel line 5 7 Connecting metering pump S0 and W0 6 5 Degrease adhesive surface for adhesive base 6. Metering pump 0 mm dia. clamp 90 moulded hose 0 mm dia. clamp 5 Fuel line 6 Cable tie, adhesive base Connecting metering pump 7 X0 Degrease adhesive surface for adhesive base. 90 moulded hose, 0 mm dia. clamp Cable tie, adhesive base Fuel line Connecting metering pump 7 5959C_EN 7
Mercedes Benz C Class S0, W0 / GLK Class X0 80l fuel tank 0 mm dia. clamp Fuel line 80 moulded hose Connecting metering pump 7 5959C_EN 8
Mercedes Benz C Class S0, W0 / GLK Class X0 Coolant circuit WARNING! Any coolant running off should be collected using an appropriate container! Install hoses so that they are kink-free. Unless specified otherwise, always fasten using cable ties. Position clamps so that no other hose can be damaged! When installing the hoses, the heater must be filled with coolant. The connection should be "inline" based on the following diagram: Hose routing diagram A B Ø 7 All spring clips without a specific designation = Black (sw) rubber isolator [x]! = 5 mm dia. = Original vehicle spring clip 5959C_EN 9
Mercedes Benz C Class S0, W0 / GLK Class X0 Discard section X. Hose A = 8mm dia hose Hose B = 80, 8x8 moulded hose B A X A = 50 B = 50 Cutting hoses to length X B Slide braided protection hoses on to hoses A and B and cut to length. Cut heat shrink plastic tubing to size. Heat shrink plastic tubing, length 50 [x] Preparing hoses A Detach pass through at the marking and remove! Removing pass through 75 Turn original vehicle spring clamp [x] according to figure Aligning clamps 76 5959C_EN 0
Mercedes Benz C Class S0, W0 / GLK Class X0 Cut out corrugated tube according to length and slide onto brake line! corrugated tube 77 Battery carrier Edge protection 00 Mounting edge protection 78 8 mm dia. hole Hole in shield plate 79 Hose bracket -fold, can be locked hose bracket 80 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Remove original vehicle hose and discard. Original vehicle spring clips will be reused. Cutting point A 8 Original vehicle spring clip Connection piece on engine outlet Connecting engine outlet 8 A Route hose A into hose bracket and route forward through pass-through! Routing in engine compartment 8 Insert hose bracket between hose A and the coolant pipe of the heat exchanger outlet lying under it. Routing in engine compartment A 8 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Connecting piece of circulating pump Connecting heater inlet A B 85 Connection piece on heat exchanger inlet Original vehicle spring clip Connecting heat exchanger inlet B 86 Route hose B into hose bracket and route forward through pass-through! Close lock! Routing in engine compartment B A 87 Battery carrier mounted Routing in engine compartment A 88 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 B Slide black (sw) rubber isolator onto hose B. A 89 Connection piece on engine outlet Align black (sw) rubber isolator Routing in engine compartment Connecting heater outlet B 90 5959C_EN
Mercedes Benz C Class S0, W0 / GLK Class X0 Combustion air a Discard section X. Combustion air pipe a = 80 Cutting combustion air pipe to length X Perforated bracket 80 Angling down perforated bracket 90 Original vehicle bolt Angle bracket angle bracket 9 Combustion air pipe 5 mm dia. spring clip combustion air pipe 9 5959C_EN 5
Mercedes Benz C Class S0, W0 / GLK Class X0 Combustion air pipe Cable tie Routing fuel line 9 5 mm dia. pipe clamp Muffler M5x0 bolt, flanged nut muffler 9 5959C_EN 6
Mercedes Benz C Class S0, W0 / GLK Class X0 Exhaust end section S0 and W0 Cut out wheel well inner panel at the markings. Discard section Cut out wheel well inner panel 95 wheel well inner panel. The exhaust end section, must be centered relative to the hole and aligned flush with the wheel well inner panel ; realign exhaust end section if necessary. Aligning exhaust end section 96 X0 Drill 5 mm dia. hole in trim. The exhaust end section, must be centered relative to the hole and aligned flush with the trim ; realign exhaust end section if necessary. Exhaust end section Aligning exhaust end section 97 Exhaust end section Aligning exhaust end section 98 5959C_EN 7
Mercedes Benz C Class S0, W0 / GLK Class X0 Final Work WARNING! Reassemble the disassembled components in reverse order. Check all hoses, clamps and all electrical connections for firm seating. Secure all loose cables using cable ties. Only use manufacturer-approved coolant. Spray the heater components with anti-corrosion wax (Tectyl 00K, Order No. 9). - Connectbattery - Fill and bleed the coolant circuit according to the vehicle manufacturer s specifications. - Teach Telestart according to "Installation documentation T9 / T00 HTM", adjust digital timer if necessary - Activate push button according to "Installation documentation T9 / T00 HTM" ( Repositioning of switch input) - Define settings of air conditioning control panel according to the "operating and maintenance instructions of TT-Evo" - Mount information label "Switch off parking heater before refueling" in area of filler neck. - For initial startup and function check, please see installation instructions WARNING: After conducting an operating test of the parking heater, carry out an "input short test" with the "Diagnosis assistance system" of the manufacturer on the vehicle. Reprogram the positioning motors in the KLA air conditioner. Feel the drive Webasto AG Postfach 80 D-8 Stockdorf / Germany National Hotline: 0805 9 78 ( Cent aus dem deutschen Festnetz) Hotfax: 095 559 5 Hotmail: hotline@webasto.de http://www.webasto.de 5959C_EN Printed in Germany 0/0 Printing: Steffen 8