Alarms & Remote Start

Alarms & Remote Start INSTALL GUIDE DOCUMENT NUMBER 809 REVISION DATE 0608 FIRMWARE COL-AL(RS)-VW6-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) OMEGA-CARLINK-GPS (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately) Automotive Data Solutions Inc. 06

VEHICLE LIST - OF PAGE OF DOC.: #809 0608 FEATURES MAKE MODEL YEAR INSTALL TYPE SECURE TAKEOVER X LOCK START/STANDALONE MOD. ARM OEM ALARM AUDI DISARM OEM ALARM DOOR LOCK DOOR UNLOCK TRUNK/HATCH RELEASE DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT* AUTOLIGHT CTRL TACHOMETER OUTPUT BRAKE PEDAL STATUS OUTPUT E-BRAKE OUTPUT A6 PTS AT -6 A6 TDI PTS AT -6 A7 PTS AT -6 A7 TDI PTS AT -6 A8 PTS AT -5 A8 TDI PTS AT -5 RS7 PTS AT -6 S6 PTS AT -6 S7 PTS AT -6 S8 PTS AT -5 *Available only if vehicle is equipped with factory hood switch. Automotive Data Solutions Inc. 06

BOX CONTENTS - OF PAGE OF DOC.: #809 0608 BOX CONTENTS MODULE 6 PIN WHITE CONNECTOR PIN BLACK CONNECTOR WHITE 5 6 PROGRAMMING BUTTON LED 7 PIN WHITE CONNECTOR 0 PIN BLACK CONNECTOR WHITE WHITE 5 6 7 A B C F 0 9 8 7 6 5 BLACK PIN WHITE CONNECTOR DATA CABLE BLUE D E BLACK DATA PORT (WEBLINK, RF, TELEMATIC) PIN BLUE CONNECTOR DATA CABLE WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc. 06

COMPATIBLE ACCESSORIES - OF PAGE OF DOC.: #809 0608 TELEMATIC KIT (accessories sold separately) 5 AMPS CARLINK MODULE DATA PORT DATA CABLE V (+) RED WHITE BLUE BLACK RED BLUE BROWN BLACK (NC) Automotive Data Solutions Inc. 06

TYPE - WIRE CHART - OF PAGE 5 OF DOC.: #809 0608 MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION AUDI WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR A6 PTS AT A6 TDI PTS AT S6 PTS AT A7 PTS AT A7 TDI PTS AT S7 PTS AT RS7 PTS AT A8 PTS AT A8 TDI PTS AT S8 PTS AT -6-6 -6-6 -6-6 -6-5 -5-5 V ~ ~ ~ ~ Red (+) Behind fuse box ~ Brake ~ ~ 0 pin 0 Red/Black (+) At brake switch ~ CanH ~ ~ ~ ~ Orange/LtGreen (DATA) Twisted wires in door harness in driver kick panel ~ CanL ~ ~ ~ ~ Orange/Brown (DATA) Twisted wires in door harness in driver kick panel ~ Ignition OBDII Black 6 pin 0 Blue/Black (+) OBDII connector ~ PTS ~ Black 06 pin 05 Black/Red (-) Push-button ~ PTS ~ Black 06 pin 06 Blue (-) Push-button ~ PTS ~ Black 06 pin 0 Black (-) Push-button ~ V ~ ~ ~ ~ Red (+) Behind fuse box ~ Brake ~ ~ 0 pin 0 Red/Black (+) At brake switch ~ CanH ~ ~ ~ ~ Orange/LtGreen (DATA) Twisted wires in door harness in driver kick panel ~ CanL ~ ~ ~ ~ Orange/Brown (DATA) Twisted wires in door harness in driver kick panel ~ Ignition OBDII Black 6 pin 0 Blue/Black (+) OBDII connector ~ PTS ~ Black 06 pin 05 Black/Red (-) Push-button ~ PTS ~ Black 06 pin 06 Blue (-) Push-button ~ PTS ~ Black 06 pin 0 Black (-) Push-button ~ V ~ ~ ~ ~ Red (+) Behind fuse box ~ Brake ~ ~ 0 pin 0 Red/Black (+) At brake switch ~ CanH ~ ~ ~ ~ Orange/LtGreen (DATA) Twisted wires in door harness in driver kick panel ~ CanL ~ ~ ~ ~ Orange/Brown (DATA) Twisted wires in door harness in driver kick panel ~ Ignition OBDII Black 6 pin 0 Blue/Black (+) OBDII connector ~ PTS ~ Black 06 pin 05 Black/Red (-) Push-button ~ PTS ~ Black 06 pin 06 Blue (-) Push-button ~ PTS ~ Black 06 pin 0 Black (-) Push-button ~ Automotive Data Solutions Inc. 06

TYPE - WIRING DIAGRAM - OF PAGE 6 OF DOC.: #809 0608 MODULE PTS PTS SWITCH A B F C D E DATA PTS (-) - 0 PTS (-) - 06 PTS (-) - 05 5 6 A B C 5 6 5 6 7 0 GRAY/YELLOW (NC) 0 GRAY/RED - PTS (-) OUTPUT 0 GREEN/YELLOW (NC) 0 GREEN/RED - PTS (-) OUTPUT 05 BLUE/YELLOW (NC) 06 BLUE/RED (NC) 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 0 ORANGE (NC) 0 ORANGE/WHITE (NC) 05 ORANGE/BLACK - PTS (-) OUTPUT 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) N00 DIODE V (+) CANL CANH IGNITION (+) - 0 BRAKE (+) - 0 OBDII A 5 6 7 8 9 TWISTED WIRES IN DOOR HARNESS IN DRIVER KICK PANEL OBDII CONNECTOR 0 5 6 BRAKE SWITCH D E 0 WHITE - V (+) CONSTANT 0 WHITE/RED (NC) 0 WHITE/BLACK 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 0 RED - V (+) WITHOUT A COMPATIBLE ACCESSORY 85 87 87A 0 86 REMOVE BATTERY A DATA CABLE COMPATIBLE ACCESSORY OR WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. 7.5 A V (+) 0 LOOPS (0 AWG) AROUND KEYFOB BEHIND DASH PANEL F 5 6 7 8 9 0 0 GREEN/BLACK- HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITCH: AFTERMARKET HOOD SWITCH (-) 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH 0 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) 0 LOOPS (0 AWG) ON KEY READER (B) (BEHIND KEY SYMBOL, BEHIND PANEL) B TWO KEYS ARE REQUIRED FOR THIS INSTALLATION. ONE KEY WILL REMAIN PERMANENTLY IN THE VEHICLE. THE OTHER KEY WILL BE USED FOR THE PROGRAMMING PROCEDURE. IT WILL THEN BE RETURNED TO THE OWNER. Automotive Data Solutions Inc. 06

MODULE PROGRAMMING PROCEDURE - OF PAGE 7 OF DOC.: #809 0608 0 STOP ACC ON START Push start button twice [x] to ON position. ENGINE START STOP 0 Wait, LED will turn solid GREEN then will turn OFF. 0 STOP ACC ON START Push start button once [x] to OFF position. ENGINE START STOP 0 Module Programming Procedure completed. Automotive Data Solutions Inc. 06

VALET MODE PROGRAMMING PROCEDURE - OF PAGE 8 OF DOC.: #809 0608 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to 5. 0 Time restriction. Complete next step within 7 seconds. 0 OFF ACC ON START Cycle ignition ON five times [5x OFF/ON] rapidly. ENGINE START STOP 0 Wait, LED will turn solid RED for seconds. 0 OFF ACC ON START Set ignition to OFF position. ENGINE START STOP 05 Valet Mode Programming Procedure completed. Automotive Data Solutions Inc. 06

PAGE 9 OF DOC.: #809 0608 MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to OFF position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 OFF ACC ON START TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP 0 0 [X] Automotive Data Solutions Inc. 06

MODULE NAVIGATION CHART - OF PAGE 0 OF DOC.: #809 0608 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 DISARM/UNLOCK BEFORE START 0 OFF 0 ON 0 RELOCK AFTER START 0 OFF 0 ON 0 RELOCK AFTER SHUTDOWN 0 OFF 0 ON 0 FORCE UNLOCK ALL ON FIRST PRESS 0 OFF 0 ON 05 N/A 0 N/A 06 N/A 0 N/A 0 DISABLE 07 FACTORY KEYLESS RS SEQUENCE 0 N/A 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 0 MIN 0 CONFIGURATION 0 05 MIN 0 0 MIN 08 MODULE RUN TIME 0 5 MIN 05 5 MIN 06 0 MIN 07 5 MIN 08 5 MIN 0 0 SEC 0 05 SEC 0 08 SEC 09 WAIT TO START DELAY 0 0 SEC 05 5 SEC 06 0 SEC 07 5 SEC 08 0 SEC 0- N/A 0 N/A 0-07 Technical Support only 0 N/A 0 N/A Automotive Data Solutions Inc. 06

REMOTE STARTER ERROR CODES - OF PAGE OF DOC.: #809 0608 REMOTE STARTER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Foot brake is ON. 0 Hood is open. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. Automotive Data Solutions Inc. 06

MODULE DIAGNOSTICS - OF PAGE OF DOC.: #809 0608 TEST MODULE LED STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence. Automotive Data Solutions Inc. 06

MODULE RESET PROCEDURE - OF PAGE OF DOC.: #809 0608 0 Disconnect all connectors from module except the BLACK -PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK -PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK -PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. 06 Module RESET completed. Automotive Data Solutions Inc. 06

INSTALLATION CHECKLIST - OF PAGE OF DOC.: #809 0608 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question : Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question : Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST 9 Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. 5 Enter vehicle and close the doors. 6 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc. 06