S4D45-AP3- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-74673 Mulfingen Phone +49 7938 8- Fax +49 7938 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart HRA 59344 General partner Elektrobau Mulfingen GmbH Headquarters Mulfingen County court Stuttgart HRB 594 Nominal data Type Motor S4D45-AP3- M4D74-GA Phase 3~ 3~ Nominal voltage VAC 46 46 Connection Y Y Frequency Hz 5 6 Type of data definition cs cs Speed min - 33 46 Power input W 85 38 Current draw A.54.6 Max. back pressure Pa 8 75 Min. ambient temperature C -5-5 Max. ambient temperature C 65 55 ml = Max. load me = Max. efficiency fa = Running at free air cs = Customer specs cu = Customer unit Subject to alterations Item no. 3846-5-998 ENG Revision 8466 Release 5-3- Page / 6
S4D45-AP3- Technical features Mass Size Surface of rotor Material of terminal box Material of blades Material of guard grille Number of blades 5 Direction of air flow Direction of rotation 7. kg 45 mm Coated in black ABS plastic Sheet steel, coated in black Steel, coated in black plastic (RAL95) "V" Counter-clockwise, seen on rotor Type of protection IP 44; Depending on installation and position as per EN 634-5 Insulation class "F" Humidity class F- Max. permissible ambient motor temp. (transp./ storage) Min. permissible ambient motor temp. (transp./storage) Mounting position Condensate discharge holes Operation mode Motor bearing Touch current acc. IEC 699 (measuring network Fig. 4, TN system) Electrical leads Cable exit Protection class Product conforming to standard + 8 C - 4 C Shaft horizontal or rotor on bottom; rotor on top on request Rotor-side S Ball bearing <.75 ma Via terminal box Variable I (if protective earth is connected by customer) EN 6335-, motor does not have factory-installed overheating protection Item no. 3846-5-998 ENG Revision 8466 Release 5-3- Page / 6
S4D45-AP3- Product drawing Direction of air flow "V" Tightening torque.5 ±. Nm 3 Cable diameter: max. mm, tightening torque.3±. Nm Item no. 3846-5-998 ENG Revision 8466 Release 5-3- Page 3 / 6
S4D45-AP3- Connection screen Y Star connection L black L blue L3 brown PE green/yellow Item no. 3846-5-998 ENG Revision 8466 Release 5-3- Page 4 / 6
S4D45-AP3- Charts: Air flow 5 Hz pfs [Pa] 5 5 95 9 85 8 75 7 65 6 55 5 45 4 35 3 5 5 5 5 5 pfs @ rho=, kg/m³ qv [CFM]..5. 5 5 3 35 qv [m³/h] 4.5 45 3.,48,46,44,4,4,38,36,34,3,3,8,6,4,,,8,6,4,,,8,6,4, 5 pfs [InHO] Measurement: LU-38669 Air performance measured as per ISO 58 Installation category A. For detailed information on the measuring set-up, please contact ebm-papst. Suction-side noise levels: LwA measured as per ISO 3347 / LpA measured with m distance to fan axis. The values given are valid under the measuring conditions mentioned above and may vary according to the actual installation situation. With any deviation from the standard set-up, the specific values have to be checked and reviewed with the unit installed. Measured values U V 46 46 f Hz 5 5 n min - 375 33 P e W 4 85 I A.49.54 qv m 3 /h 498 3475 p fs Pa 8 U = Supply voltage f = Frequency n = Speed P e = Power input I = Current draw qv = Air flow p fs = Pressure increase Item no. 3846-5-998 ENG Revision 8466 Release 5-3- Page 5 / 6
S4D45-AP3- Charts: Air flow 6 Hz pfs [Pa] 5 5 95 9 85 8 75 7 65 6 55 5 45 4 35 3 5 5 5 5. pfs @ rho=, kg/m³ qv [CFM].5. 3 qv [m³/h] 4.5 3. 5,48,46,44,4,4,38,36,34,3,3,8,6,4,,,8,6,4,,,8,6,4, pfs [InHO] Measurement: LU-3867 Air performance measured as per ISO 58 Installation category A. For detailed information on the measuring set-up, please contact ebm-papst. Suction-side noise levels: LwA measured as per ISO 3347 / LpA measured with m distance to fan axis. The values given are valid under the measuring conditions mentioned above and may vary according to the actual installation situation. With any deviation from the standard set-up, the specific values have to be checked and reviewed with the unit installed. Measured values U V 46 46 f Hz 6 6 n min - 535 46 P e W 3 38 I A.53.6 qv m 3 /h 555 435 p fs Pa 75 U = Supply voltage f = Frequency n = Speed P e = Power input I = Current draw qv = Air flow p fs = Pressure increase Item no. 3846-5-998 ENG Revision 8466 Release 5-3- Page 6 / 6