igh Pressure fi lters FP series Maximum pressure up to bar Flow rate up to 7 l/min igh Pressure fi lters
FILTER SIZING The correct filter sizing have to be based on the variable pressure drop depending by the application. For example, for the return filter the pressure drop have to be in the range..6 bar. The pressure drop calculation is performed by adding together the value of the housing with the value of the filter element. The pressure drop in the housing is proportional to the fluid density (kg/dm ); all the graphs in the catalogue are referred to mineral oil with density of.86 kg/dm. The filter element pressure drop is proportional to its viscosity (mm /s), the corrective factor Y is related to an oil viscosity different than mm /s. Sizing data for single cartridge, head at top pc = housing pressure drop [bar] pe = element pressure drop [bar] Y = Multiplication factor Y (see correspondent table), depending on the filter element size, on the filter element lenght and on the filter media Q = flow rate (l/min) V reference viscosity = mm /s (cst) V = operating viscosity in mm /s (cst) pe = Y : x Q x (V/V) p Tot. = pc + pe Calculation examples with LP Mineral oil Variation in viscosity Application data: Top tank return filter with inline connections Pressure Pmax = bar Flow rate Q = l/min Viscosity V = 6 mm /s (cst) Oil viscosity =.86 kg/dm Required filtration efficiency = μm with absolute filtration With bypass valve and / inlet connection From the working pressure and the flow rate we understand it should be possible using the following top tank return filter series: MPT, MP and FRI. Let s proceed with MPT series. The size doesn t achieve the required flow rate, therefore we have to consider the size. The final version of size (,,, and ) will be then defined in function of the mounting characteristics. pc =. bar ( see graphic below, considering size with the max available lenght * to get the lowest pressure drop) pe = (. : ) x x (6/) =.7 bar p Tot. =. +.7 =. bar The selection is correct because the total pressure drop value is inside the admissible range for top tank return filters. It is of course possible trying to find a different solution, according to the mounting position or to other commercial need, repeating the previous steps while using a different series or lenght. MPT Length.... * G / 6 8 housings p pressure drop. The curves are plotted using mineral oil with density of.86 kg/dm in compliance with ISO 968. p varies proportionally with density. Corrective factor Corrective factor Y, to be used for the filter element pressure drop calculation. The values depend to the filter size and lenght and to the filter media. Reference viscosity mm /s Return filters element Type MF MF MFX MF MFX MF 8 MFX 8 MF 9 MFX 9 MF MFX MF 7 MFX 7 CU CU CU CU CU 6 CU 8 MR MR MR 6 MR 8 A 7. 9.. 7. 8. 7.. 6..67.69.69...9.8 78..88...96.6 9..7 7.8.....6.8..6.8..7.6.7.7. Absolute filtration Nominal filtration Series N Series A6 A A6 A P P M M6 M9.8. 6. 9. 6.... 8. 7....8. 9. 6.6...68...8.. 9....7.7.7.87.6.8 8..88...68.8 7..8 6.87.97.8.8.8..6.8.9...6..6.8.6. 8.67 6.86.6..6.68.6.9.88.6.9 8.....8. 6.9..7.6.6...8.68..8.6.8....7. 6. 8.7.7...6..9..8..6...9..7. 6......9...6..76.6..8...7. 9. 6.88.......6..9.6 9..78..7..7.6..7.8.9..7.86..9.8.6...... 6..6..6.9.8...96.9.9. 9..78..7..7.9.9..7.6.8.96.77.7.8......8....96.7..96.6.9..87...9 8...7.9.6....8.7.7..8.6..7.7.7.6.8.9.7......96.8.6......6.....9..6.7........9.8.8.8..... Introduction
Corrective factor Corrective factor Y, to be used for the filter element pressure drop calculation. The values depend to the filter size and lenght and to the filter media. Reference viscosity mm /s Suction filters element Type SF Nominal filtration N Series P P 6 Low & Medium pressure filters element Type CU A 6..6 8.7.76 FILTER SIZING Absolute filtration Nominal filtration NW Series N Series A6 A A6 A P P M.6. 7.9. 8.7 6..7.8 8. 6..7.6.87....86.6..9.6.9..8.... Return / Suction filters element Type RSX 6 A.. Absolute filtration A6..87 A.8. CU DN 6... 7.9...8.9.7 7...66...9..89..66.9.8.9.7.98..7..98..6.6...8..8....6....9..8..8 RSX 6.6..9.7..86.6.96.6 CU 6...6..8..7.8.8.8.6.9.7.7...78.6..7.78....7.7.....6..7.9.8.9..8.6. CU 9.86.6.... CU 9...8..9.7..8.6... MR 6 7.88.78.6..6..96.7 Introduction
FILTER SIZING Corrective factor Corrective factor Y, to be used for the filter element pressure drop calculation. The values depend to the filter size and lenght and to the filter media. Reference viscosity mm /s igh pressure filters element Type P A.7.8. 77.76 Absolute filtration N R Series A6 A A6.7 6.6 9.68 8. 8. 7.8.8 8.7.6 9..8.67 A 8.6 7..7 6.7 Nominal filtration N Series M Stainless steel high pressure filters element Type P A.7.8. 77.76 Absolute filtration N Series A6 A A6.7 6.6 9.68 8. 8. 7.8.8 8.7.6 9..8.67 A 8.6 7..7 6.7 P 9 7.66 6.7 6.7..8.7.77 8..6.7.8 8.8.67 8..8.9.9. P 9 7.66 6.7 6.7..8.7.77 8..6.7.8.88.67 8..8 P.7. 7.7. 7...6 6..7 6.6.6.7 8.9 6..6. 9.9 7.8.7. 7.9.9.6.8..6...7.8 P.7. 7.7. 7...6 6..7 6.6.6.7 8.9 6..6. 9.9 7.8.7. 7.9.9.6.8. P 6 8..6..6.6.88.6 6. 8.8 9.66.88 6.8.7 7..9.8..8 P.. 6.8 8.8.6 6. 9.7 6.6.8 8.66 6.8.6.78.. P P.. 6.8.88..7. 8.8.6 6. 9.7.8..77 9.7 6.6.8..7..98 8.66 6.8.6.7.8.87.78.78....88.77..78....7.6.7 element Type P A.8 8.6. 9.9 Absolute filtration U Series A6 A A6 9.7. 97. 8..7 9..6 6.79 9. 7..8 9.7 A 6.78 7.6.8 8. P..7..8..67.77.98....78..9.77..68.9.86.68.6..7.68.8...8.. P 9 7.66 6.7 6.7..8.7.77 8..6.7.8 8.8.67 8..8 element Type A Absolute filtration N Series A6 A A6 A Nominal filtration N Series M P 7. 9..8. 9.86..9 9..9 9....68 7. 6...9 8.6 6.9.8.7.88.6.69. F.6..8.9.7..8.6..8...9.8.8.8.6. P 9.6.8 8.96.. 7.6. 7.86.89.7 7.6.6.9..7 Introduction
Selection Software FILTER SIZING Step Select FILTERS Step Choose fi lter group (Return, Pressure, etc.) Step Choose fi lter type (MPF, MPT, etc.) in function of the max working pressure and the max fl ow rate Step Push PROCEED Step Insert all application data to calculate the fi lter size following the sequence: working pressure working fl ow rate working pressure drop working temperature fl uid material and fl uid type fi ltration media connection type Step 6 Push CALCULATE to have result; in case of any mistake, the system will advice which parameter is out of range to allow to modify/adjust the selection Step 7 Download PDF Datasheet Report.aspx pushing the button Drawing Introduction
igh Pressure filters
igh Pressure fi lters FP series Maximum pressure up to bar Flow rate up to 7 l/min igh Pressure fi lters
FP GENERAL INFORMATION Technical data igh Pressure filters Maximum pressure up to bar Flow rate up to 7 l/min housing materials ead: Phosphatized cast iron ousing: Phosphatized steel Bypass valve: AISI 6L (FP ) Brass (FP 6 ) Steel (FP ) Reverse Flow: Steel (FP FP ) Check valve: Steel Pressure Working pressure: MPa ( bar) Test pressure: 6 MPa (6 bar) Burst pressure: 6 MPa (6 bar) Pulse pressure fatigue test: cycles with pressure from to MPa ( bar) Bypass valve Opening pressure 6 kpa (6 bar) Other opening pressures on request. p element type Microfibre filter elements series N: bar Microfibre filter elements series R: bar (not available for FP and FP ) Microfibre filter elements series : bar Microfibre filter elements series S: bar (only for FP ) Wire mesh filter elements series N: bar Fluid flow through the filter element from OUT to IN. Seals Standard NBR series A Optional FPM series V Temperature From C to + C FP 6 : Inline Inlet/Outlet FP : 9 Inlet/Outlet Note FP filters are provided for vertical mounting Weights [kg] and volumes [dm ] FP FP 6 FP FP FP Lenght Weights [kg]..8.6..6.6.8 7. 8.7 9.76.9 6.8 8.7.8 7..7.69 6.7. Lenght Volumes [dm ].........76.97..7.9..7...8 6. ydraulic symbols Style S Style B Style T Style D Style V Style Z igh Pressure filters 6
The curves are plotted using mineral oil with density of.86 kg/dm in compliance with ISO 968. Check Valve p varies proportionally with density. / FP... FP FP. 7 FP. FP 6. Check Valve /. / FP GENERAL INFORMATION.. FP... FP. 7 FP Flow rate l/min. Check Flow Valve rate l/min /.. / FP FP FP.... Check Valve Check Valve. / /. /...... Bypass valve pressure drop FP / FP. Check Valve 6 8 6 8 6... FP FP 6 9 housing with check valve. FP 6.... FP 6 7. Check Valve /. / FP / FP.. Check Valve. Valves FP.. Check Valve 6 / 7... FP 6 6 7 FP 6 8 FP 6 6 7 6 8 6 FP. FP.. /. 7 8 8 7 96 Pressure drop in reverse flow valves... Check Valve FP Pressure drop. 6 7 FP. / Valves Check Valve Bypass valve pressure drop.. FP FP 6 FP 6 8 6 FP 6 7 / 6 8 8 7 96 6 9.... 7 8.6.. FP FP FP. 6 7 Reverse flow In filter direction housings p pressure drop Pressure drop in reverse flow valves Bypass valve pressure drop Valves Valv Byp FP FP FP Reverse flow In filter direction 7 igh Pressure filters
FP Designation & Ordering code COMPLETE FILTER Series and size Configuration example: FP B A B A N P FP FP Length Valves S B V Z Seals A V FP FP Without bypass With bypass 6 bar With reverse flow, without bypass With reverse flow, with bypass 6 bar NBR FPM A G/ B / NPT C SAE / UNF D G/8 E /8 NPT F SAE 6 9/6 8 UNF Connection for differential indicator Without With connection Filtration rating (filter media) A Inorganic microfiber µm A6 Inorganic microfiber 6 µm A Inorganic microfiber µm A6 Inorganic microfiber 6 µm A Inorganic microfiber µm M Wire mesh µm Element p N bar bar Valves S B V Z Execution P MP Filtri standard Pxx Customized Element series and size P FILTER ELEMENT Configuration example: P A A N P Element length Filtration rating (filter media) A Inorganic microfiber µm A6 Inorganic microfiber 6 µm A Inorganic microfiber µm A6 Inorganic microfiber 6 µm A Inorganic microfiber µm M Wire mesh µm Seals A V NBR FPM Element p N bar bar Execution P MP Filtri standard Pxx Customized ACCESSORIES Differential indicators page page DEA Electrical differential indicator 7 DTA Electronic differential indicator DEM Electrical differential indicator 78 DVA Visual differential indicator DLA Electrical / visual differential indicator 89 DVM Visual differential indicator DLE Electrical / visual differential indicator 9 Additional features page T Plug igh Pressure filters 8
FP FP FP Dimensions Recommended clearance space for maintenance Recommended clearance space for maintenance length FP [mm] 9 A B C D E F R M6 / UNC M6 / UNC Recommended clearance space for maintenance length FP [mm] 9 A B C D E F R M6 / UNC M6 / UNC 9 igh Pressure filters
FP FP6 FP FP Designation & Ordering code COMPLETE FILTER Series and size Configuration example: FP V A G A6 S P FP6 FP FP Length FP6 FP FP Valves S B T D V Z Without bypass With bypass 6 bar With check valve, without bypass With check valve, with bypass 6 bar With reverse flow, without bypass With reverse flow, with bypass 6 bar FP6 FP FP Seals A NBR V FPM G G G G G G6 F F F F F F6 FP6 FP FP G/ G/ / NPT / NPT G/ G / NPT NPT G / G / / NPT / NPT SAE 8 / 6 UNF SAE /6 UN SAE /6 UN SAE 6 /6 UN / SAE psi/m SAE psi/m / SAE psi/unc SAE psi/unc / SAE 6 psi/m SAE /8 UN SAE 7/8 UN / SAE psi/m / SAE psi/m / SAE psi/unc / SAE psi/unc / SAE 6 psi/m / SAE 6 psi/unc / SAE 6 psi/unc Filtration rating (filter media) A Inorganic microfiber µm A6 Inorganic microfiber 6 µm A Inorganic microfiber µm A6 Inorganic microfiber 6 µm A Inorganic microfiber µm M Wire mesh µm Element p N R S bar bar bar bar Valves S B T D V Z Execution P MP Filtri standard P Maintenance from the bottom of the housing Pxx Customized length Element series and size P6 P P FILTER ELEMENT Configuration example: P A6 A S P Element length P6 P P Filtration rating (filter media) A Inorganic microfiber µm A6 Inorganic microfiber 6 µm A Inorganic microfiber µm A6 Inorganic microfiber 6 µm A Inorganic microfiber µm M Wire mesh µm Differential indicators page page DEA Electrical differential indicator 7 DTA Electronic differential indicator DEM Electrical differential indicator 78 DVA Visual differential indicator DLA Electrical / visual differential indicator 89 DVM Visual differential indicator DLE Electrical / visual differential indicator 9 Additional features page T Plug igh Pressure filters Seals A V ACCESSORIES NBR FPM Element p N R S bar bar bar bar Execution P MP Filtri standard Pxx Customized
FP6 FP FP FP Dimensions Recommended clearance space for maintenance FP6 length GG GGGG6 [mm] 96 7 9 R M8 /6 UNC igh Pressure filters
FP Dimensions FP6 FP FP Recommended clearance space for maintenance FP length GG GGGG6 FF FF F F6 [mm] 6 7 8 R M /8 UNC M /8 UNC M /8 UNC igh Pressure filters
FP6 FP FP FP Dimensions Length Length Recommended clearance space for maintenance Recommended clearance space for maintenance FP length [mm] 99 77 [mm] Execution P P GG GGGG6 FF FF F F6 R M / UNC M / UNC M / UNC igh Pressure filters
FP FP Designation & Ordering code COMPLETE FILTER Series and size Configuration example: FP V A G A6 S P FP Length Valves S B T D V Z Seals A V Without bypass With bypass 6 bar With check valve, without bypass With check valve, with bypass 6 bar With reverse flow, without bypass With reverse flow, with bypass 6 bar NBR FPM G G / G / NPT G SAE 7/8 UN F / SAE psi/m F / SAE psi/unc F SAE psi/m F F F6 F7 F8 SAE psi/unc / SAE 6 psi/m / SAE 6 psi/unc SAE 6 psi/m SAE 6 psi/unc Filtration rating (filter media) A Inorganic microfiber µm A6 Inorganic microfiber 6 µm A Inorganic microfiber µm A6 Inorganic microfiber 6 µm A Inorganic microfiber µm M Wire mesh µm Element p N S bar bar Valves S B T D V Z Execution P MP Filtri standard P Maintenance from the bottom of the housing P Drain plug on length Pxx Customized length FILTER ELEMENT Element series and size P Configuration example: P A6 A S P Element length Filtration rating (filter media) A Inorganic microfiber µm A6 Inorganic microfiber 6 µm Seals A Inorganic microfiber µm A NBR A6 Inorganic microfiber 6 µm V FPM A Inorganic microfiber µm M Wire mesh µm Element p N S bar bar Execution P MP Filtri standard Pxx Customized ACCESSORIES Differential indicators page page DEA Electrical differential indicator 7 DTA Electronic differential indicator DEM Electrical differential indicator 78 DVA Visual differential indicator DLA Electrical / visual differential indicator 89 DVM Visual differential indicator DLE Electrical / visual differential indicator 9 Additional features page T Plug igh Pressure filters
FP FP Dimensions Length Length Recommended clearance space for maintenance Recommended clearance space for maintenance FP length [mm] 96 6 8 [mm] Execution P P 8 6 G GG F F F F F F6 F7 F8 R M / UNC M / UNC M / UNC M / UNC M / UNC igh Pressure filters
FP Order number for spare parts SPARE PARTS d e FP a b c Item: series FP nr. pc. for version (with indicator port) Q.ty: pc. Q.ty: pc. (a e) Seal Kit code number Indicator connection plug element NBR FPM NBR FPM See order table 9 Q.ty: nr. pcs. for version (without indicator port) T TV d FP e g a b c c f b Item: series FP Q.ty: pc. Q.ty: pc. Q.ty: pc. (a g) Seal Kit code number Indicator connection plug element NBR FPM NBR FPM See order table T TV igh Pressure fi lters 6
SPARE PARTS FP Order number for spare parts FP 6 m h d e g 6 a m h b c c b f Item: series FP 6 FP FP Q.ty: pc. Q.ty: pc. Q.ty: pc. Q.ty: pc. Q.ty: pc. (a m) 6 Seal Kit code number Indicator connection plug Bypass assembly Nonbypass assembly element NBR FPM NBR FPM NBR FPM NBR FPM See order table 6 69 7 76 8 8 T TV 6 7 8 6 7 8 9 9 9 7 igh Pressure fi lters