GENERAL INFORMATION SIVAG Pumpen Ges.m.b.H. is primarily concerned with manufacturing and distributing of pumps for many years. Basically the products are used for industrial purposes. Since 1989 the head office of SIVAG Pumpen has been in Hollabrunn. The support for national and international customers is raised without any distributors or sales organisations directly from SIVAG Hollabrunn. THE BUSINESS STRATEGY IS CONCENTRATED ON: Customer- and target oriented solutions on unbureaucratic way in cooperative collaboration Best price/performance ratio Competent contact persons and high qualified technical personal Short delivery times in consequence of transparent and accurate business processes THE PRODUCT RANGE CONTAINS PUMPS FOR: Chemicals Clean water Foods Viscous fluids Waste water 3
INDEX page 6 page 7 Volute casing pumps acc. EN 22858 NC Volute casing pumps in bloc design NCB page 8 page 9 Self-priming centrifugal pumps S Self-priming internal gear pumps R page 10 page 11 Lobe pumps B Stainless steel centrifugal pumps acc. EN 733 3S page 12 page 13 Stainless steel centrifugal pumps acc. EN 733 3M Stainless steel centrifugal pumps acc. EN 733 3P page 14 page 15 Close coupled centrifugal pumps in stainless steel CD_2CD Centrifugal pump in stainless steel with open impeller DWO page 16 page 17 Submersible pumps with Vortex-impeller DG Submersible pumps with multi-channel impeller DR page 18 page 19 Submersible pumps with grinder system GR Submersible pumps with high head impeller AP page 20 page 21 Centrifugal pumps for chemicals TMR_ZMR Centrifugal pumps for chemicals acc. EN 22858 ZGE 4
INDEX page 22 page 23 Chemical vertical sump pumps KG Air operated double diaphragm pumps DDA page 24 page 25 Impeller pumps EP Self-priming liquid ring pumps EP 5
NC VOLUTE CASING PUMP NC NC ACC. EN EN 22858 Horizontal single-stage volute casing pumps, with bearing bracket. Nominal duty points and main dimensions in accordance with DIN 24256 EN 22858. Single-stage volute casing pumps of series NC are used for pumping clean and low contaminated liquids without abrasive, coarse or extended solids. - Maximum nominal pressure: 16 bar - Temperature: up to 260 C - Volute casing pumps are made of stainless steel 1.4408 (AISI 316) and cast iron. Special material combinations are produced on request. - Shaft sealing alternative with mechanical seal or stuffing box. The materials and the execution of the mechanical seal and the packing in accordance to the pumped liquid. TECHNICAL CHARACTERISTICS - Capacity: up to 1100 m³/h - Discharge head: up to 158 m W.S. - Connections: from DN 32 to DN 300 - Motor rotation speed: 1450 min -1 and 2900 min -1 GENERAL PERFORMANCE CURVE 6
VOLUTE CASING PUMP IN BLOC DESIGN NCB NCB Close coupled horizontal single-stage volute casing pumps, with IEC-norm electric motor. Single-stage volte casing pumps of series NCB are used for pumping clean and low contaminated liquids without abrasive, coarse or extended solids. - Maximum nominal pressure: 16 bar - Temperature: up to 180 C - Volute casing pumps are made of stainless steel 1.4408 (AISI 316) and cast iron. Special material combinations are produced on request. - Shaft sealing alternative with mechanical seal or stuffing box. The materials and the execution of the mechanical seal and the packing in accordance to the pumped liquid. TECHNICAL CHARACTERISTICS - Capacity: up to 500 m³/h - Discharge head: up to 158 m W.S. - Connections: from DN 32 to DN 200 - Motor rotation speed: 1450 min -1 and 2900 min -1 GENERAL PERFORMANCE CURVE 7
SELF-PRIMING CENTRIFUGAL PUMP S Self-priming centrifugal pumps with open impeller are used for pumping liquids containing solids up to 80 mm diameter and for abrasive liquids. The special design makes the S series a quick self-priming pump. - Maximum nominal pressure: 16 bar - Self-priming up to 8-9 m H2O - Self-priming pumps are made of stainless steel 1.4408 (AISI 316) and cast iron. Special materials are produced on request. - Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 1500 m³/h - Discharge head: up to 70 m H2O - Connections: from DN40 to DN300 PERFORMANCES Type Connections Solids Capacity Head Motor Impeller Bearing- Zoll mm Ø mm m³/h m kw Ø mm bracket 2900 min -1 S 40 1 ½ 40 20 20/16/7 5/10/15 1,1 110 1 S 45 1 ½ 40 15 22/14/5 10/20/30 2,2 172 2 S 50 2 50 25 40/30/13 5/10/15 2,2 120 2 S 60 2 50 17 42/30/14 10/20/30 4,0 172 3 S 63 2 50 15 45/28/18 30/40/45 7,5 195 3 S 68 2 50 25 42/30/16 35/45/55 11 220 4 S 80 3 80 30 80/47/20 5/15/20 4 140 3 S 83 3 80 20 80/57/20 15/25/20 7,5 172 3 S 88 3 80 30 93/70/32 25/35/45 15 220 4 S 100 4 100 45 135/100/60 10/20/25 11 160 4 S 108 4 100 40 135/105/65 25/35/45 22 220 5 1450 min -1 S 65 2 50 25 40/28/10 5/10/15 2,2 220 4 S 85 3 80 40 80/62/20 5/10/15 4,0 220 4 S 105 4 100 45 140/100/50 5/10/15 5,5 220 4 S 121 4 100 45 178/100/50 10/20/25 11 280 5 S 150 6 150 60 260/180/80 5/10/15 11 220 5 S 161 6 150 60 310/230/110 10/15/20 18,5 280 5 S 180 6 150 45 320/250/160 20/25/30 30 358 6 S 201 8 200 57 500/400/250 5/10/15 22 280 6 S 230 8 200 72 630/440/250 20/30/35 45 358 6 960 min -1 S 170 6 150 50 300/240/120 5/10/15 11 358 6 S 220 8 200 72 530/420/180 5/10/15 18,5 358 6 S 300 12 300 76 1200/1000/450 5/10/15 55 405 7 8
SELF-PRIMING INTERNAL GEAR PUMP R The self-priming internal gear pumps of series R are positive displacement rotary pumps. The capacity is directly proportional to the rotation speed. This pump is available as bare shaft pump with bearing bracket. - Maximum nominal pressure: 16 bar - Temperature: -60 C to +300 C - Internal gear pumps are made of stainless steel 1.4408 (AISI 316), cast iron EN-GJL-250 and nodular cast iron EN-GJS-400. Special materials are produced on request. - Shaft sealing alternative with mechanical seal, stuffing box or magnetic drive. The materials and the execution of the mechanical seal, packing or magnetic drive in accordance to the liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 350 m³/h - Viscosity: up to 100.000 mm²/s (cst) - Connections from DN 40 to DN 250 PERFORMANCES Type Connection Viscosity Rotation speed Capacity Performance at: Weight DN PN16 4 bar 8 bar (l/ min -1 ) (Zoll) mm²/s (cst) min -1 m³/h kw kw kg R 35 (0,043) R 40 (0,08) R 50 (0,22) R 65 (0,48) R 80 (1,15) R 105 (2,25) R 150 (3,8) R 180 (6,8) R 200 (14) R 250 (21) 40 (1 ¼ ) 40 (1 ¼ ) 50 (2 ) 65 (2 ½ ) 80 (3 ) 100 ( 4 ) 150 (6 ) 150 (6 ) 200 (8 ) 250 (10 ) 200 1450 3,7 1,4 1,7 4000 720 1,9 1,2 1,4 25000 450 1,2 1 1,2 200 1450 7 2 2,8 4000 720 3,5 1,6 2 25000 450 2,2 1,3 1,6 200 960 12,6 3 4,5 4000 560 7,5 2,7 3,6 25000 355 5 2,2 2,8 200 720 20,5 5,6 8,1 4000 450 13 5 6,6 25000 280 8,3 3,6 4,6 200 630 43 8,9 14 4000 400 28 9,1 12,5 25000 250 18 7,5 9,6 200 560 75,5 15 23,7 4000 355 49 16 22 25000 224 31,3 14,3 18,3 200 500 114 20,7 34 4000 315 73 21,6 30,3 25000 200 47 19 24,8 200 400 163 4000 250 102 25000 160 65 200 315 265 4000 200 168 25000 125 105 200 280 350 4000 180 330 25000 112 140 On request On request On request 11 12 32 46 84 152 240 9
LOBE PUMP B Lobe pumps of series B are positive displacement rotary pumps. The capacity is directly proportional to the rotation speed. Two synchronously driven rotors are rotating in a casing. This construction provides a very gentle pumping of fluids. - Maximum working pressure: 10 (20) bar - Temperature: up to 180 C - All hydraulic parts are made of stainless steel AISI 316. The gear box is made in cast iron EN-GJL- 250. Special alloys and surface hardenings are available on request. - Shaft sealing alternative with mechanical seal, stuffing box or special lip seal. The materials and the execution of the mechanical seal, packing or lip seal in accordance to the liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 300 m³/h - Viscosity: up to 100.000 mm²/s (cst) - Connections from DN25 to DN200 PERFORMANCES Type Theor. Max. Max. Max. working pressure (bar) Connection Capacity Rot. speed Performance ST with shaft SM with shaft HP Duplex+ l/100 min -1 min -1 kw AISI 316 Duplex AISI 316 Duplex Acteon DN Zoll B 100 3 1400 1,5 7 10 - - - 25 1 B 105 7 1000 4 10 13 15 18-40 1 ½ B 110 12 1000 4 10 13 15 18 20 40 1 ½ B 115 18 1000 5,5 7 10 12 15-40 1 ½ B 215 23 950 7,5 10 13 15 18 20 40 1 ½ B 220 34 950 7,5 7 10 12 15-50 2 B 325 55 720 18,5 10 13 15 18 20 65 2 ½ B 330 70 720 18,5 7 10 12 15-80 3 B 390 90 720 18,5 5 7 10 12-80 3 B 430 116 600 30 10 13 15 18 20 80 3 B 440 155 600 30 7 10 12 15-100 4 B 470 240 500 45 10 13 15 18 20 100 4 B 490 330 500 45 7 10 12 15-100 4 B 550 400 500 45 5 - - - - 125 5 B 660 700 500 75 7 - - - - 150 6 B 680 1050 500 75 4 - - - - 200 8 10
STAINLESS STEEL CENTRIFUGAL PUMP 3S ACC. EN 733 3S Horizontal single-stage volute casing pumps in stainless steel with dimensions and performances acc. EN 733. The 3S -series is a close coupled execution with standard IEC-norm electric motor. These pumps are used for pumping clean and low contaminated liquids (also used for various chemicals). - Maximum nominal pressure: 10 bar - Temperature: -20 C to +120 C - Centrifugal pumps are made in stainless steel 1.4301 (AISI 304) and 1.4571 (AISI 316). - Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 240 m³/h - Discharge head: up to 90 m W.S. - Connections from DN 32 to DN 100 - Motor rotation speed: 1450 min -1 and 2900 min -1 CURVES 2900 MIN -1 CURVES 1450 MIN -1 11
STAINLESS STEEL CENTRIFUGAL PUMP 3M ACC. EN 733 Horizontal single-stage volute casing pumps in stainless steel with dimensions and performances acc. EN 733. The 3M -series is a close coupled execution with electric motor with extended shaft. These pumps are used for pumping clean and low contaminated liquids (also used for various chemicals). - Maximum nominal pressure: 10 bar - Temperature: -20 C to +120 C - Centrifugal pumps are made in stainless steel 1.4301 (AISI 304) and 1.4571 (AISI 316). - Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid. TECHNIAL CHARACTERISTICS - Capacity: up to 240 m³/h - Discharge head: up to 90 m W.S. - Connections from DN 32 to DN 100 - Motor rotation speed: 1450 min -1 and 2900 min -1 CURVES 2900 MIN -1 CURVES 1450 MIN -1 12
STAINLESS STEEL CENTRIFUGAL PUMP 3P ACC. EN 733 Horizontal single-stage volute casing pumps in stainless steel with dimensions and performances acc. EN 733. Pumps of 3P -series are available as bare shaft pumps with bearing bracket. These pumps are used for pumping clean and low contaminated liquids (also used for various chemicals). - Maximum nominal pressure: 10 bar - Temperature: -20 C to +120 C - Centrifugal pumps are made in stainless steel 1.4301 (AISI 304) and 1.4571 (AISI 316). - Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 240 m³/h - Discharge head: up to 90 m W.S. - Connections from DN 32 to DN 100 - Motor rotation speed: 1450 min -1 and 2900 min -1 CURVES 2900 MIN -1 CURVES 1450 MIN -1 13
CENTRIFUGAL PUMP IN STAINLESS STEEL STEEL CD_2CD Close coupled horizontal pumps in single-stage (CD) or two impeller (2CD) execution in stainless steel with electric motor with extended shaft directly connected to the pump. The centrifugal pumps CD and 2CD are used for pumping clean and low contaminated liquids without abrasive, coarse or extended solids. - Maximum nominal pressure: 8 bar - Temperature: -5 C to +120 C - Centrifugal pumps are only made in stainless steel 1.4301 (AISI 304). - Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 15 m³/h - Discharge head: up to 70 m W.S. - Connections from G1 to G1 ½ - Motor rotation speed: 2900 min -1 CURVES CD CURVES 2CD 14
CENTRIFUGAL PUMP IN STAINLESS STEEL DWO WO Horizontal single-stage centrifugal pump with open impeller in stainless steel with electric motor with extended shaft directly connected to the pump. Centrifugal pumps of series DWO are used for pumping clean and contaminated liquids without abrasive components. - Maximum nominal pressure: 8 bar - Temperature: -5 C to +110 C - Centrifugal pumps are only made in stainless steel 1.4301 (AISI 304). - Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 65 m³/h - Discharge head: up to 18 m W.S. - Connections from G2 to G2 ½ - Motor rotation speed: 2900 min -1 CURVES 15
SUBMERSIBLE PUMP DG DG Submersible pumps series DG with vortex-impeller with wide flow, for pumping all kinds of waste water, sewage and sludge. The vortex-impeller grants pumping fluids containing solids up to 150 mm diameter. - Maximum nominal pressure: 6 bar - Temperature: up to +40 C - Pumps are made of cast iron, stainless steel AISI 316 and bronze. Special materials are produced on request. - Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid. TECHNICAL CHARACTERISTICS - Capacity: up to 380 m³/h - Discharge head: up to 23 m W.S. - Connections from G1 ½ to DN 150 - Motor rotation speed: 960 min -1, 1450 min -1 and 2900 min -1 GENERAL PERFORMANCE CURVE 16
SUBMERSIBLE PUMP DR DR Submersible pumps series DR with open multi-channel impeller for pumping clean and waste water, with solids contaminated sewage and sludge. This kind of impeller grants pumping fluids containing solids up to 120 mm diameter. - Maximum nominal pressure: 6 bar - Temperature: up to +40 C - Pumps are made of cast iron, stainless steel AISI 316 and bronze. Special materials are produced on request. - Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid. TECHNICAL CHARATERISTICS TICS - Capacity: up to 500 m³/h - Discharge head: up to 52 m W.S. - Connections from G1 ¼ to DN 150 - Motor rotation speed: 960 min -1, 1450 min -1 and 2900 min -1 GENERAL PERFORMANCE CURVE 17
SUBMERSIBLE PUMP GR GR Submersible pumps series GR with open multi-channel impeller and cutting system. This kind of pumps with special impeller and grinder system is used for pumping waste water with long fibers and cutting able solids. - Maximum nominal pressure: 6 bar - Temperature: up to +40 C - Pumps are only made in cast iron. - Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid. TECHNICAL CHARACTERISTICS - Capacity: up to 110 m³/h - Discharge head: up to 54 m W.S. - Connections from G1 ½ to DN 100 - Motor rotation speed: 1450 min -1 and 2900 min -1 GENERAL PERFORMANCE CURVE 18
SUBMERSIBLE PUMP AP AP Submersible pumps series AP with open multi-channel high head impeller. This kind of pumps with special impeller is designed for high delivery heads. They are used for pumping clean and waste water and low contaminated liquids with small solids. - Maximum nominal pressure: 8 bar - Temperature: up to +50 C - Pumps are only made in cast iron. - Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid. TECHNICAL CHARACTERISTICS - Capacity: up to 42 m³/h - Discharge head: up to 60 m W.S. - Connections from G1 ½ to G2 - Motor rotation speed: 2900 min -1 GENERAL PERFORMANCE CURVE 19
CENTRIFUGAL PUMP FOR CHEMICALS TMR_ZMR TMR_ZMR Close coupled horizontal single-stage centrifugal pumps with standard IEC-norm electric motor. This centrifugal pumps series TMR and ZMR is used for pumping clean liquids (mainly Chemicals). Shaft sealing is available with mechanical seal or magnetic drive. - Maximum nominal pressure: 8 bar - Temperature: -20 C to +100 C - Centrifugal pumps are made of PP (glass fiber reinforced Polypropylene) or E-CTFE (Etylene- Chloro TrifluoroPolyetylene carbon fibers filled / PVDF-similar). - Shaft sealing is available with mechanical seal or magnetic coupling. Pump execution and materials, mechanical seals and bushings in accordance to the pumped liquid. TECHNICAL CHARACTERISTICS - Capacity: up to 55 m³/h - Discharge head: up to 40 m W.S. - Connections from DN 40 to DN 50 - Motor rotation speed: 2900 min -1 GENERAL PERFORMANCE CURVE 20
ZGE CENTRIFUGAL PUMP FOR CHEMICALS ZGE ZGE ACC. EN EN 22858 Horizontal single-stage volute casing pumps, with bearing bracket. Nominal duty points and main dimensions in accordance with EN 22858. Single-stage volute casing pumps of series ZGE are used for pumping clean liquids (mainly chemicals) without abrasive, coarse or extended solids. - Maximum nominal pressure: 16 bar - Temperature: -40 C to +120 C - Centrifugal pumps are made of PP (Polypropylene), PE (Polyethylene), PVDF (Polyvinilidene Fluoride) or PVC (polyvinyl chloride). - Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 1700 m³/h - Discharge head: up to 155 m W.S. - Connections from DN 32 to DN 300 - Motor rotation speed: 1450 min -1 and 2900 min -1 CURVE 2900 MIN -1 CURVE 1450 MIN -1 21
CHEMICAL VERTICAL SUMP PUMP KGK KGK The vertical sump pumps series KGK are used for pumping clean liquids (mainly chemicals) without abrasive, coarse or extended solids. They have column and volute casing submerged, own mechanical support and motor mounted above the liquid to be pumped. - Maximum immersion depth: 4 m - Temperature: -10 C to +40 C - Centrifugal pumps are made of PP (glass fiber reinforced Polypropylene) and PVDF (Polyvinilidene Fluoride) - Pump execution and materials and bushings in accordance to the pumped liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 270 m³/h - Discharge head: up to 85 m W.S. - Connections from DN 25 to DN 100 - Motor rotation speed: 1450 min -1 and 2900 min -1 CURVE 2900 MIN -1 CURVE 1450 MIN -1 22
AIR OPERATED DOUBLE DIAPHRAGM PUMP DDA DDA The air operated double diaphragm pumps of series DDA are used for pumping a variety of different liquids (mainly chemicals), without abrasive, coarse or extended solids. These pumps can be installed submerged in the pumped liquid. The DDA-pumps are self-priming. And they can be used for thin and viscose fluids. - Maximum suction head: 6 m - Temperature: -10 C to +40 C - The air operated double diaphragm pumps are made of PP (glass fiber reinforced Polypropylene), PVDF, carbon fiber filled PVDF, Aluminium, stainless steel AISI 316 (AISI 316 polished FDA). - Pump execution and materials, diaphragms and valves in accordance to the pumped liquid. TECHNICAL CHARACTERISTICS - Capacity: up to 40 m³/h - Discharge head: up to 70 m W.S. - Connections from G ¼ to G2 23
IMPELLER PUMP EP EP The special construction of impeller pumps provides a very gentle pumping of fluids. The flexible impeller grants pumping thin and high viscose liquids (up to 50.000 cp). The impeller pump is selfpriming up to 6 m and can be used in both directions. - Maximum nominal pressure: 4 bar - Temperature: up to +100 C - Impeller pumps are made in stainless steel AISI 304 and AISI 316. - Shaft sealing with mechanical seal. Materials of mechanical seal and impeller in accordance to the pumped liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 45 m³/h - Discharge head: up to 30 m W.S. - Connections from ¾ to DN 100 - Motor rotation speed: 470 min -1 to 1400 min -1 GENERAL PERFORMANCE CURVE 24
SELF-PRIMING LIQUID RING PUMP EP EP The liquid ring pumps are used for pumping clean fluids without solids up to viscosity of 100 cp. The special construction of the pump casing grants that the pump is self-priming and can be used in both directions. - Maximum nominal pressure: 6 bar - Temperature: up to +100 C - Liquid ring pumps are made in stainless steel AISI 316 and bronze. - Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid. TECHNICAL CAL CHARACTERISTICS - Capacity: up to 30 m³/h - Discharge head: up to 40 m W.S. - Connections from ¾ to DN 65 - Motor rotation speed: 1400 min -1 to 2800 min -1 GENERAL PERFORMANCE CURVE 25
Aumühlgasse 12 14 A-2020 Hollabrunn Tel: +43(0)2952-3144-0 Fax: +43(0)2952-3144-4 office@sivag-pumpen.at www.sivag-pumpen.at