HPA terminal filter units eiling diffusers: 60, 650, 65, 655, 656, 659, 660 Wall grilles: 670 or critical air purity and hygiene requirements Used in medicine, biology, pharmaceuticals, and sensitive technical areas onstructions with shut-off damper or volume flow controller ontent overview eneral information... ace plates...... Special information... eiling diffuser 60... eiling diffuser 650... eiling diffuser 65... 2 3 5 6 8 9 eiling diffuser 655... 10 eiling diffuser 656... 11 eiling diffuser 659... 12 eiling diffuser 660... 13 Wall grille 670... 1 Specification text... 15 eaflet 6 / 1 / 2 / N
eneral information etail Application HPA terminal filter units for ceiling and wall installation as final filters (last filter stage) and for air distribution. itting of filter elements for the separation of suspended particles such as aerosols, toxic dusts, viruses, and bacteria from the supply and extract air. aterial asing made of sheet steel with powder coating (RA 9010). Available in stainless steel upon request. onstruction -Type 60: With side entry circular spigot -Type 650: With side entry rectangular spigot -Type 65: With manually adjustable shutoff damper and side entry circular spigot -Type 655: With shut-off damper, with pneumatic actuator and side entry circular spigot -Type 655: With shut-off damper, with pneumatic actuator and side entry circular spigot -Type 656: With shut-off damper, with electric actuator and side entry circular spigot -Type 659: With volume flow limiter and side entry circular spigot -Type 660: With top circular entry spigot -Type 670: Wall grille quipment - asing with clamping mechanism (two-point fixing) for the HPA filter. - Sealing integrity test facility and pressure measuring points to monitor differential operating pressure. - iffuser face plate for ceiling applications: Types Q-A,, VW, and Q made of sheet steel with powder coating (RA 9010). Type AQ-A made of anodised aluminium profiles. - rille face plate for wall application: Type S-A made of sheet steel with powder coating (RA 9010). Type AS-A made of anodised aluminium profiles. Options - lamping mechanism for the minipleat filter panel as four-point fixing. - Side suspension points and locations of differential pressure measurement points. - Sealing integrity test facility and internal measuring tube. Associated TROX filter elements Associated filters to be ordered separately. Installation and maintenance iffuser face plate with central fixing to facilitate its removal for filter change and decontamination. Suitable filter elements inipleat filter panels used as HPA filters (7/9/../..) - High-performance filters for the most critical requirements of air purity and sterility - Type 780 (11), Type 781 (H13), Type 782 (H1). -onstruction: rame made of, galvanised sheet steel, or stainless steel with flat section seal; frame made of extruded aluminium profiles with flat section seal or fluid seal. 2 HPA terminal filter units - eaflet 6/1/2/N
ace plates etail ace plates - iffuser face plate for ceiling applications: Types Q-A,, VW, and Q made of sheet steel with powder coating (RA 9010). Type AQ-A made of anodised aluminium profiles. - rille face plate for wall application: Type S-A made of sheet steel with powder coating (RA 9010). Type AS-A made of anodised aluminium profiles. onfiguration and code letters iffuser face plate Type ode letter 2 iffuser face Type ode letter 2 plate AQ-A Q-A A S VW VW 625 x 8 VW 680 x 5 V Other types of diffuser face plate and filter cell constructions available upon request. Table 1: iffuser face plates for ceiling application Q Table 2: iffuser face plates for ceiling application Possible combinations of unit size and diffuser face plate The diffuser face plates are a part of the unit and must be included in the purchase order. rille face plates for wall applications, see page 1. Type AQ-A/Q-A AQ-A/Q-A AQ-A/Q-A AQ-A/Q-A AQ-A/Q-A VW 00 x 16 VW 500 x 2 VW 600 x 2 VW 625 x 2 VW 680 x 2 VW 625 x 8 VW 680 x 5 Q Q Q Q Q Unit size /N P/Q / / / /N P/Q / / / /N P/Q / / / / / /N P/Q / / / iffuser face plate imensions in Size 00 398 500 98 600 598 625 623 680 676 00 398 500 98 600 598 625 623 680 676 00 398 500 98 600 598 625 623 680 676 625 623 680 676 00 398 500 98 600 598 625 623 680 676 iffuser face plate ax. 1) volume flow rate m 3 /h 320 600 850 970 1100 320 50 600 600 600 320 500 700 700 700 825 825 320 50 600 600 600 urther information lima 1-2/11/0/ lima 1-2/11/0/ lima 1-2/11/0/ lima 1-2/11/0/ lima 1-2/11/0/ lima 1-2/6/0/ lima 1-2/6/0/ lima 1-2/6/0/ lima 1-2/6/0/ lima 1-2/6/0/ lima 1-2/7/0/ lima 1-2/7/0/ lima 1-2/7/0/ lima 1-2/7/0/ lima 1-2/7/0/ lima 1-2/7/0/ lima 1-2/7/0/ lima 1-2/15/0/ lima 1-2/15/0/ lima 1-2/15/0/ lima 1-2/15/0/ lima 1-2/15/0/ ode letter 2 A/S A/S A/S A/S A/S V V V V V Table 3: Volume flow rates for the ceiling diffusers 1) Volume flow rate at 0 db (A) HPA terminal filter units - eaflet 6/1/2/N 3
10 Unit type: Type 60 (last number = spigot code number) Type 650 Type 65 Type 655 Type 656 Type 659 Type 660 (last number = spigot code number) Type 670 or the diffuser face plate, see pages 3 and 1: A=AQ-A (ceiling diffuser), AS-A (wall grille) S=Q-A (ceiling diffuser), S-A (wall grille) = V=VW = VW 625 x 8 = VW 680 x 5 =Q Sealing integrity test facility: 1 = Sealing integrity test facility (standard) 2 = Sealing integrity test facility and internal measuring tube 1) Unit size: See the technical data in Tables to 1. Number of fixing points: 0 = 2 fixing points (standard) = fixing points 1) aterial of casing: 0 = Sheet steel, powder-coated in RA 9010 (standard) S = Sheet steel, powder-coated in RA 9005 = Stainless steel, pickled lange width: 0 = lange width (standard) = lange width, limiting size 10-55 1) Zero Suspension and measuring points: 1) 0 = Top (standard) S=Side Zeros 1) Options only available for ceiling-mounted HPA filter units. xample: Type 68 with spigot code number eiling-mounted HPA filter Type 60 with spigot diameter of 28 with spigot code number 8: 68 iffuser face plate Type : Sealing integrity test facility and internal measuring tube: 2 Unit size: 575 x 575 x 78 : Two-point fixing: 0 asing made of sheet steel, powder-coated in RA 9010 (standard): 0 lange width (standard): 0 Side suspension and measuring points: S xample: Type 65 without spigot code number eiling-mounted HPA filter Type 65: 65 iffuser face plate Type VW: V Sealing integrity test facility and internal measuring tube: 2 Unit size: 575 x 575 x 78 : our-point fixing: asing made of sheet steel, powder-coated in RA 9010 (standard): 0 lange width (standard): 0 Side suspension and measuring points: S 6 8 2 0 0 0 0 S 0 0 6 5 V 2 0 0 0 S 0 0 HPA terminal filter units - eaflet 6/1/2/N
Special information Sealing integrity test facility and measuring tube 3 2 0 3 Test groove ilter seal onnection for sealing integrity test facility easuring tube ø 8 x 1.5 heesehead screw 6 x 10 etail drawing 1: Sealing integrity test facility etail drawing 2: Internal measuring tube Suspension and measuring points 50 0 0 S 0 0 9 Suspension easuring point on upstream side (plus) easuring point on downstream side (minus) Suspension easuring point on upstream side (plus) easuring point on downstream side (minus) etail drawing 3: Top suspension and measuring points etail drawing : Side suspension and measuring points HPA terminal filter units - eaflet 6/1/2/N 5
eiling diffuser 60 1 eiling diffuser Type 60 X S U 0 etail drawing 5: 60 with side entry circular spigot etail drawing 6: etail X Seal etail drawing 7: minipleat filter panels with flat section seal etail drawing 8: minipleat filter panels with fluid seal 6 HPA terminal filter units - eaflet 6/1/2/N
eiling diffuser 60 imensions of 60 and filter element size 6 6 A 1 A 2 0 0 Unit size N N P P Q Q ilter element size B H T 1) 35 35 78/91 35 35 78/91 35 35 150 35 35 150 35 35 78/91 35 35 78/91 35 35 150 35 35 150 535 535 150 535 535 150 535 535 150 575 575 150 575 575 150 575 575 150 610 610 150 610 610 150 610 610 150 Nominal volume flow rate 2) l/s m³/h 90 320 90 320 165 590 165 590 150 50 150 50 285 1025 285 1025 20 850 20 850 20 850 0 1585 0 1585 0 1585 515 1850 515 1850 515 1850 585 2100 585 2100 585 2100 imensions in U S 1 371 388 398 330 10 85 119 21 299 371 388 398 330 10 135 69 189 299 371 388 398 330 10 85 186 281 366 371 388 398 330 10 135 136 256 366 61 88 98 20 15 85 11 209 29 61 88 98 20 15 135 6 18 29 61 88 98 20 15 85 186 281 366 61 88 98 20 15 135 136 256 366 561 588 598 520 15 135 6 18 29 561 588 598 520 15 135 6 209 3 561 588 598 520 15 135 6 23 39 561 588 598 520 15 135 136 256 366 561 588 598 520 15 135 136 281 16 561 588 598 520 15 135 136 306 66 601 618 623 560 10 135 69 189 299 601 618 623 560 10 135 69 21 39 601 618 623 560 10 135 69 239 399 601 618 623 560 10 135 136 256 366 601 618 623 560 10 135 136 281 16 601 618 623 560 10 135 136 306 66 636 663 676 595 15 135 6 18 29 636 663 676 595 15 135 6 209 3 636 663 676 595 15 135 6 23 39 636 663 676 595 15 135 136 256 366 636 663 676 595 15 185 86 231 366 636 663 676 595 15 185 86 256 16 Weight Spigot code no. Approx. (last digit kg of 1 ) 17 1, 3 17, 6 17 1, 3 17, 6 21 3 21, 6 21 3 21, 6 22 6 22 8 22 9 22 6 22 8 22 9 23 6 23 8 23 9 23 6 23 8 23 9 23 6 23 8 23 9 23 6 23 8 23 9 Table : for 60 1) inipleat filter panel with flat section seal / minipleat filter panel with fluid seal 2) Related to minipleat filter panel 781 in the specified filter size Spigot dimensions Ø Spigot code number (last digit of 1) 123 1 18 3 158 198 6 28 8 298 9 Table 5: Spigot dimensions and code numbers ist of abbreviations A = Overall width of rectangular inlet spigot flange 650 = iameter of entry spigot = Overall dimension of case including entry spigot 650 = ace flange width = imensions from face flange to centerline of spigot 1 = asing height = Overall dimensions of flange = Overall dimensions of diffuser face plate N = Overall length of grille face plate (Type 670) = Top suspension distance between holes = Overall dimensions of casing S = istance from casing flange to damper operator cover U = asing extension HPA terminal filter units - eaflet 6/1/2/N 7
eiling diffuser 650 A 1 98 18 eiling diffuser Type 650 X etail drawing 9: 650 with side entry rectangular spigot etail drawing 10: etail X imensions of 650 and filter element size Unit size N P Q ilter element size B H T 1) 35 35 78/91 35 35 150 35 35 78/91 35 35 150 535 535 150 575 575 150 610 610 150 l/s Table 6: for 650 Nominal volume flow rate 2) m³/h 90 320 165 590 150 50 285 1025 20 850 0 1585 515 1850 585 2100 1) inipleat filter panel with flat section seal / minipleat filter panel with fluid seal 2) Related to minipleat filter panel 781 in the specified filter size imensions in A 1 371 18 01 388 398 330 10 29 299 371 18 01 388 398 330 10 316 366 61 508 91 88 98 20 15 2 29 61 508 91 88 98 20 15 316 366 561 608 591 588 598 520 15 2 29 561 608 591 588 598 520 15 316 366 601 68 631 618 623 560 10 29 299 601 68 631 618 623 560 10 316 366 636 683 666 663 676 595 15 2 29 636 683 666 663 676 595 15 316 366 Weight Approx. kg 17 17 21 21 22 22 23 23 23 23 8 HPA terminal filter units - eaflet 6/1/2/N
eiling diffuser 65 etail onstruction Air-tight shut-off damper according to IN N 1751, lass (nominal size 125, lass 3) for use in ventilation systems with critical hygiene requirements. Installation and maintenance ue to the integral shut-off damper, filter change and maintenance work is possible without disturbance to the system operation. With additional manually adjustable shut-off damper, sealing integrity test facility, and internal pressure measuring point. eiling diffuser Type 65 120 S 1 X etail drawing 11: 65 with side entry circular spigot etail drawing 12: etail X imensions of 65 and filter element size Unit size P ilter element size B H T 1) 35 35 78/91 35 35 78/91 Nominal volume flow rate 2) l/s m³/h 90 320 150 50 20 850 imensions in Ø 1 S 371 388 398 330 10 125 313 28 5 61 88 98 20 15 160 308 23 9 561 588 598 520 15 200 308 23 9 601 618 623 560 10 200 313 28 5 636 663 676 595 15 200 308 23 9 Weight Approx. kg 27 31 32 33 35 Table 7: for 65 1) inipleat filter panel with flat section seal / minipleat filter panel with fluid seal 2) Related to minipleat filter panel 781 in the specified filter size HPA terminal filter units - eaflet 6/1/2/N 9
eiling diffuser 655 etail eiling diffuser Type 655 onstruction Air-tight, automatic shut-off damper according to IN 196 Part with pneumatic actuator (fail safe closed). This guarantees that in the case of loss of control pressure the room is isolated. eiling diffuser with internal pressure measuring point. Installation and maintenance ilter change and maintenance work is possible without interruption of the system operation; access to the actuator without having to open the ceiling. Pneumatic actuator - ontrol pressure: 0.6 to max. 1.0 bar. -ompressed air connection: push-on fitting for PT hose 6 x 1. 65 7 1 U X etail drawing 13: 655 with side entry circular spigot U = 89 ; only for unit size for filter size 35 x 35 etail drawing 1: etail X imensions of 655 and filter element size Unit size P ilter element size B H T 1) 35 35 78/91 35 35 78/91 Nominal volume flow rate 2) l/s m³/h 90 320 150 50 20 850 imensions in Ø 1 371 388 398 330 10 125 313 28 61 88 98 20 15 160 308 23 561 588 598 520 15 200 308 23 601 618 623 560 10 200 313 28 636 663 676 595 15 200 308 23 Weight Approx. kg 29 33 3 35 37 Table 8: for 655 1) inipleat filter panel with flat section seal / minipleat filter panel with fluid seal 2) Related to minipleat filter panel 781 in the specified filter size 10 HPA terminal filter units - eaflet 6/1/2/N
eiling diffuser 656 etail onstruction As Type 655, with electric actuator for the shut-off damper (fail safe closed). lectric actuator - ains connection: 230 V, 50 Hz. - Power consumption: Approx. 10 W. - Supply wiring: 2 x 0.75 ². eiling diffuser Type 656 65 7 1 U X etail drawing 15: 656 with side entry circular spigot U = 89 ; only for unit size for filter size 35 x 35 etail drawing 16: etail X imensions of 656 and filter element size 6 5 6 A 1 Unit size P ilter element size B H T 1) 35 35 78/91 35 35 78/91 Nominal volume flow rate 2) l/s m³/h 90 320 150 50 20 850 imensions in Ø 1 371 388 398 330 10 125 313 28 61 88 98 20 15 160 308 23 561 588 598 520 15 200 308 23 601 618 623 560 10 200 313 28 636 663 676 595 15 200 308 23 Weight Approx. kg 29 33 3 35 37 Table 9: for 656 1) inipleat filter panel with flat section seal / minipleat filter panel with fluid seal 2) Related to minipleat filter panel 781 in the specified filter size HPA terminal filter units - eaflet 6/1/2/N 11
eiling diffuser 659 etail onstruction With integral volume flow limiter Type V made of high-quality plastic for the limitation and control of constant volume flow rates. Type V volume flow limiter The volume flow limiter is set to a reference volume flow rate at the factory and can be readjusted within a volume flow rate range of > 5:1. or more information regarding the volume flow limiter, see the separate V eaflet. eiling diffuser Type 659 50 1 Ø X etail drawing 17: 659 with side entry circular spigot etail drawing 18: etail X imensions of 659 and filter element size Unit size P ilter element size B H T 1) 35 35 78/91 35 35 78/91 Nominal volume flow rate 2) l/s m³/h 90 320 150 50 20 850 imensions in Ø 1 371 388 398 330 10 160 313 28 61 88 98 20 15 200 308 23 561 588 598 520 15 250 333 73 601 618 623 560 10 250 338 78 636 663 676 595 15 250 333 73 Weight Approx. kg 28 32 33 3 36 Table 10: for 659 1) inipleat filter panel with flat section seal / minipleat filter panel with fluid seal 2) Related to minipleat filter panel 781 in the specified filter size 12 HPA terminal filter units - eaflet 6/1/2/N
eiling diffuser 660 1 eiling diffuser Type 660 X etail drawing 19: 660 with top circular entry spigot etail drawing 20: etail X imensions of 660 and filter element size 6 6 6 A 1 A 2 0 0 Unit size N P Q ilter element size B H T 1) 35 35 78/91 35 35 150 35 35 78/91 35 35 150 535 535 150 575 575 150 610 610 150 Nominal volume flow rate 2) l/s m³/h 90 320 165 590 150 50 285 1025 20 850 0 1585 515 1850 585 2100 imensions in 1 371 388 398 330 10 299 371 388 398 330 10 366 61 88 98 20 15 29 61 88 98 20 15 366 561 588 598 520 15 29 561 588 598 520 15 366 601 618 623 560 10 299 601 618 623 560 10 366 636 663 676 595 15 29 636 663 676 595 15 366 Weight Spigot code number Approx. (last digit kg of 1 ) 17 1, 3,, 6 17 1, 3,, 6 21 6, 8, 9 21 6, 8, 9 22 6, 8, 9 22 6, 8, 9 23 6, 8, 9 23 6, 8, 9 23 6, 8, 9 23 6, 8, 9 Table 11: for 660 1) inipleat filter panel with flat section seal / minipleat filter panel with fluid seal 2) Related to minipleat filter panel 781 in the specified filter size Spigot dimensions Ø 123 18 158 198 28 Spigot code number (last digit of 1 ) 1 3 6 8 298 9 Table 12: Spigot dimensions and code numbers HPA terminal filter units - eaflet 6/1/2/N 13
Wall grille 670 etail onstruction Three different installation depths, with sealing integrity test facility and measuring point for monitoring of the differential operating pressure. rille face plate made of sheet steel with powder coating (RA 9010) Type S-A or made of anodised aluminium profiles Type AS-A. aintenance rille face plate with concealed fixing to facilitate its removal for filter change and decontamination. Wall grille Type 670 etail drawing with code letters rille face plate Type ode letter 2 AS-A S-A A S Table 13: rille face plate for wall application 663 585 331 280 680 N 38 35 etail drawing 21: 670 imensions of 670 and filter element size Type AS-A AS-A AS-A S-A S-A S-A Unit size 1 2 3 1 2 3 ilter size in B H 305 610 305 610 305 610 305 610 305 610 305 610 T 78 150 292 78 150 292 Nominal volume flow rate 1) l/s m³/h 150 50 270 980 325 1165 150 50 270 980 325 1165 Wall grille imensions in 213 285 27 213 285 27 N 690 690 690 696 696 696 Weight Approx. kg 10 10 11 10 10 11 ode letter 2 A A A S S S 1 Table 1: for 670 1) Related to minipleat filter panel 781 in the specified filter size 1 HPA terminal filter units - eaflet 6/1/2/N
Specification text Specification text HPA terminal filter units: HPA terminal filter unit for ceiling and wall installation as final filter (last filter stage) and for air distribution. itting of filter elements for separation of suspended particles. asing made of sheet steel with powder coating (RA 9010). asing with clamping mechanism (two-point or four-point fixing) for the HPA filter. Sealing integrity test facility, at the top of the unit, pressure measuring points to monitor differential operating pressure. iffuser face plate made of sheet steel with powder coating (RA9010) or anodised aluminium profiles. eiling diffuser Type 60: With side entry circular spigot eiling diffuser Type 650: With side entry rectangular spigot eiling diffuser Type 65: With manually adjustable shut-off damper and side entry circular spigot eiling diffuser Type 655: With automatic adjustable shut-off damper (pneumatic actuator) and side entry circular spigot eiling diffuser Type 656: With automatic adjustable shut-off damper (electric actuator) and side entry circular spigot eiling diffuser Type 659: With volume flow limiter and side entry circular spigot eiling diffuser Type 660: With top entry circular spigot Wall grille Type 670: Three different installation depths, with sealing integrity test facility and pressure measuring point : Nominal volume flow rate l/s (m³/h) imensions of casing imensions of diffuser/grille face plate Net weight kg Order number Type of diffuser/grille face plate ake: TROX ist of abbreviations A = Overall width of rectangular inlet spigot flange 650 = iameter of entry spigot = Overall dimension of case including entry spigot 650 = ace flange width = imensions from face flange to centerline of spigot 1 = asing height = Overall dimensions of flange = Overall dimensions of diffuser face plate N = Overall length of grille face plate (Type 670) = Top suspension distance between holes = Overall dimensions of casing S = istance from casing flange to damper operator cover U = asing extension HPA terminal filter units - eaflet 6/1/2/N 15
TROX mbh Siemensstraße 2 757 och, ermany Phone +9 (0) 28 23/10 09-0 ax +9 (0) 28 23/10 09-1 -mail troxfilter@trox.de www.troxtechnik.com ilters Subject to change / All rights reserved / TROX mbh (1/2010)