EURO 90 Subrack and Caseframe www.apw.eu.com
Subracks This range of subracks is made in aluminium, supplied with a conductive surface finish that gives excellent electrical conductivity. (Alodine 1000) available in 3U and 6U heights and thee different Board depth in 160, 220 and 280 mm. Subracks can be supplied with DIN41612 connector or backplane mounting with rear extrusion. The subrack is light weight, but strong. The fixed puncture guides are on multiples of 5.08 mm with a minimum distance of 10.16 mm. Subrack EURO 90 ALO 3U - 6U C1040 Note: card guides are not included in the kit (see pag. 277)
Subracks 3 Unit A B C D E 3HE C2 3/160 176.4 90 123.4 118.5 C1040-04A 3HE C2 3/220 236.4 90 183.4 118.5 C1040-05A 3HE C2 3/280 296.4 90 243.4 118.5 C1040-06A 6HE C2 6/160 176.4 90 123.4 118.5 C1040-13A 6HE C2 6/220 236.4 90 183.4 118.5 C1040-14A 6HE C2 6/280 296.4 90 243.4 118.5 C1040-15A 3HE C4 3/160 176.4 122.4 123.4 118.5 C1040-25A 3HE C4 3/220 236.4 122.4 183.4 118.5 C1040-26A 3HE C4 3/280 296.4 122.4 243.4 118.5 C1040-27A 6HE C4 6/160 176.4 122.4 123.4 118.5 C1040-28A 6HE C4 6/220 236.4 122.4 183.4 118.5 C1040-29A 6HE C4 6/280 296.4 122.4 243.4 118.5 C1040-30A Item Quantity per kit 3U end plates angles 1 1033-03ALO 2 2 2 2 2 2 6U end plates angles 1 1033-06ALO 2 2 2 2 2 2 84TE front tie bars 4 1034-01ALO 2 2 2 2 2 2 2 2 2 2 2 2 84TE rear tie bars DIN 41494 2 1037-01ALO 2 2 2 2 2 2 84TE rear tie bars backplane 7 1041-01ALO 2 2 2 2 2 2 84TE centre tie bars DIN 41494 8 1043-01ALO 1 1 1 84TE centre tie bars backplane 9 1046-01ALO 1 1 1 Screw 4 MA x 15 TC ZIN. 5 V1204-15004 20 20 20 16 16 16 20 20 20 16 16 16 Packaging 0688-01 1 1 1 1 1 1 Packaging 0688-02 1 1 1 1 1 1 End plates 3/160 3 1047-01ALO 2 2 End plates 3/220 3 1047-02ALO 2 2 End plates 3/280 3 1047-03ALO 2 2 End plates 6/160 3 1047-04ALO 2 2 End plates 6/220 3 1047-05ALO 2 2 End plates 6/280 3 1047-06ALO 2 2 C1040-30A C1040-29A C1040-28A C1040-27A C1040-26A C1040-25A C1040-15A C1040-14A C1040-13A C1040-06A C1040-05A C1040-04A www.apw.eu.com Tel: +39 011 7725024
Subracks Different configuration The examples below shows different possibilities of ap plication accessories available like hinged front panels, modular panel, plug-in units, divider kit or rear cover. Plug-in (see pag.270-271-272) Modular panel (see pag. 273-274) Hinged panel (see pag. 276) Rear cover (see pag. 276). Horizontally hinged panel Code C0620 Vertically hinged panel Code C0625 Modular panel Code C0731... Subrack with rear cover Code C1060
19 Caseframe 3HE and 6HE 19 EURO 90 Caseframe The 19 caseframe has the same technical characteristic of the desk top version. The 3U side aluminium extrusion can be used to form the 6U case frame version. The 19 rack version is only supplied in the 84TE wide version and available with four different depth. The top and bottom covers are fixed through screws and therefore are totally independent. 5 Unit A B 3HE 3U/160 132.5 238.3 C1110-03A 6HE 6U/160 265.9 238.3 C1110-06A 3HE 3U/220 132.5 298.3 C1110-13A 6HE 6U/220 265.9 298.3 C1110-16A 3HE 3U/280 132.5 358.3 C1110-23A 6HE 6U/280 265.9 358.3 C1110-26A 3HE 3U/340 132.5 418.3 C1110-33A 6HE 6U/340 265.9 418.3 C1110-36A 1 Top cover 9 Front tie bar 17 Side cover 2 Side cover 10 Handle screw 18 Bottom cover (plain) 3 19 end plates angle 11 Rear panel 19 M4 x 14 TC screw 4 5 6 7 8 Top handle support Handle extrusion Front handle cover Bottom handle support Endplate extrusion 12 13 14 15 16 Plastic bush M2.5 front panel screw Rear angle screw Rear endplates angle M2.5 tapped strip 20 2.9 x 9.5 TS screw 21 Plastic insert cover fixing 22 Plastic insert cover support www.apw.eu.com Tel: +39 011 7725024
19 Caseframe 1 Top cover 9 Endplate extrusion 17 Rear endplates angle 2 Side cover 10 Front tie bar 18 Rear panel 3 19 end plates angle 11 Bottom cover (plain) 19 Side cover 4 Top handle support 12 Handle screw 20 M4 x 14 TC screw 5 Handle extrusion 13 M2.5 tapped strip 21 2.9 x 9.5 TS screw 6 19 angle fixing screw 14 Plastic bush 22 Plastic insert cover fixing 7 Front handle cover 15 M2.5 front panel screw 23 Plastic insert cover support 8 Bottom handle support 16 Rear angle screw
19 Caseframe 2HE and 4HE 19 EURO 90 caseframe This caseframe model is specifically developed for 2U and 4U versions. Available only in the 84TE. The rear panel is already included in the kit. A table version is available upon request. 7 Unit A C 2HE 2U/160 88.1 238.3 C1050-02A 4HE 4U/160 177 238.3 C1050-04A 2HE 2U/220 88.1 298.3 C1050-12A 4HE 4U/220 177 298.3 C1050-14A 2HE 2U/280 88.1 358.3 C1050-22A 4HE 4U/280 177 358.3 C1050-24A 2HE 2U/340 88.1 418.3 C1050-32A 4HE 4U/340 177 418.3 C1050-34A DIN 41612 and motherboard mounting accessories For insertion and installation of motherboard on DIN41612 connector, rear tie bars kit has to be ordered separately. Kit contents : 2 rear tie bars with 8 screws, 3U caseframe 3 rear tie bars with 12 screws, 6U caseframe Unit A (width) B C D Weight Kg DIN 41612 connector kit 84TE 3 431.8 90-122.5 0.450 C1063-32A Motherboard kit 84TE 3 431.8-122.4 122.5 0.360 C1063-35A DIN 41612 connector kit 42TE 6 218.44 90-255.9 0.427 C1064-52A Motherboard kit 42TE 6 218.44-122.4 255.9 0.305 C1064-55A DIN 41612 connector kit 84TE 6 431.8 90-255.9 0.700 C1064-82A Motherboard kit 84TE 6 431.8-122.4 255.9 0.530 C1064-85A www.apw.eu.com Tel: +39 011 7725024
19 Caseframe 3HE and 6HE 19 EURO 90 caseframe This range of aluminium desk top caseframes is available in two different European card dimensions, 100 and 233,4 mm and four different depth. With the rear tie bars kit, the motherboard or DIN 41612 connector can be mounted inside. 2 raised feet that can be altered and a rear panel are included in the kit while a bottom vented cover is available upon request. Top, side and bottom covers are supplied in pale grey colour. 1 2 3 4 5 6 7 8 Top cover Front endplate Top handle grip Handle extrusion Front handle cover Bottom handle support Side cover Endplate extrusion Bottom cover (plain) 9 Front tie bar 18 Side cover 10 11 12 13 14 15 16 17 Handle screw Rear panel Plastic bush 2.5MA front panel screw Rear angle screw Rear endplate angle 2.5 strapped strip 19 Feet fixing screw 20 Rear feet 21 Concealed front feet 22 Plastic insert cover fixing 23 2.9 x 9.5 TS x screw 24 Plastic insert cover fixing 25 Plastic insert cover support
19 Caseframe 9 1 2 3 4 5 6 7 8 Top cover Side cover Front endplate Top handle support Handle extrusion Rear angle screw Front handle cover Bottom handle support Front tie bar 9 Endplate extrusion 18 Rear panel 10 11 12 13 14 15 16 17 Bottom cover (plain) Handle screw 2.5 tapped strip Plastic bush 2.5MA front panel screw Rear angle screw Rear endplate angle 19 Side cover 20 Feet fixing screw 21 Rear feet 22 Concealed front feet 23 Tie bar screw 24 2.9 x 9.5 TS screw 25 Plastic insert cover fixing 26 Plastic insert cover support Unit A B C D 3HE 84TE 3U/160 132.5 238.3 431.8 447.8 C1120-01A 6HE 84TE 6U/160 265.9 238.3 431.8 447.8 C1120-02A 3HE 84TE 3U/220 132.5 298.3 431.8 447.8 C1120-03A 6HE 84TE 6U/220 265.9 298.3 431.8 447.8 C1120-04A 3HE 84TE 3U/280 132.5 358.3 431.8 447.8 C1120-05A 6HE 84TE 6U/280 265.9 358.3 431.8 447.8 C1120-06A 3HE 84TE 3U/340 132.5 418.3 431.8 447.8 C1120-07A 6HE 84TE 6U/340 265.9 418.3 431.8 447.8 C1120-08A 3HE 42TE 3U/160 132.5 238.3 218.44 234.44 C1120-31A 6HE 42TE 6U/160 265.9 238.3 218.44 234.44 C1120-32A 3HE 42TE 3U/220 132.5 298.3 218.44 234.44 C1120-33A 6HE 42TE 6U/220 265.9 298.3 218.44 234.44 C1120-34A 3HE 42TE 3U/280 132.5 358.3 218.44 234.44 C1120-35A 6HE 42TE 6U/280 265.9 358.3 218.44 234.44 C1120-36A 3HE 42TE 3U/340 132.5 418.3 218.44 234.44 C1120-37A 6HE 42TE 6U/340 265.9 418.3 218.44 234.44 C1120-38A Concealed tilt feet Concealed tilt feet www.apw.eu.com Tel: +39 011 7725024
Plug-in units 3HE EURO 90 modular plug-in units The modular plug-in units can be fitted into 3U EURO 90 subracks or caseframes through four standard card guides (see number part 0577). The plug-in unit can carry one or two single 100 x 160, 100 x 220, 100 x 280 EURO. The cards can be inserted at the left or the right. The drawers can be covered horizontally with a screen upon request. Connector hole on request Front dimension Contents of kit Qty Material Front panel 1 Alodine 1000 Rear panel 1 Alodine 1000 Side extrusion 2 Alodine 1000 Extruded handle 1 Alodine 1000 Fixings Side extrusion Rear view Connector hole on request (MOQ) The rear panel can be supplied with the holes for DIN41612 connection upon request. A B C D Plug-in 3U/160 10TE 50.46 167 47.66 - C1035-01A Plug-in 3U/160 12TE 60.62 167 56.02 29.7 *C1035-02A Plug-in 3U/160 14TE 70.78 167 66.18 39.86 C1035-03A Plug-in 3U/160 15TE 75.86 167 71.26 44.94 C1035-04A Plug-in 3U/160 18TE 91.1 167 86.5 60.18 C1035-05A Plug-in 3U/160 21TE 106.34 167 101.74 75.42 C1035-06A Plug-in 3U/220 10TE 50.46 227 47.66 - C1035-10A Plug-in 3U/220 12TE 60.62 227 56.02 29.7 *C1035-11A Plug-in 3U/220 14TE 70.78 227 66.18 39.86 C1035-12A Plug-in 3U/220 15TE 75.86 227 71.26 44.94 C1035-13A Plug-in 3U/220 18TE 91.1 227 86.5 60.18 C1035-14A Plug-in 3U/220 21TE 106.34 227 101.74 75.42 C1035-15A Plug-in 3U/280 10TE 50.46 287 47.66 - C1035-19A Plug-in 3U/280 12TE 60.62 287 56.02 29.7 *C1035-20A Plug-in 3U/280 14TE 70.78 287 66.18 39.86 C1035-21A Plug-in 3U/280 15TE 75.86 287 71.26 44.94 C1035-22A Plug-in 3U/280 18TE 91.1 287 86.5 60.18 C1035-23A Plug-in 3U/280 21TE 106.34 287 101.74 75.42 C1035-24A * M.O.Q. (Minimum order quantity)
Plug-in units 4HE EURO 90 plug-in units The 4U plug-in unit has the same technical characteristic as the 3U and 6U version. Height and four rail extrusions are the main differences. 11 Contents of kit Qty Material Front panel 1 Alodine 1000 Rear panel 1 Alodine 1000 Module rails 4 Alodine 1000 Extruded handle 1 Alodine 1000 Fixings Rear panel Unit A B C D E F 4HE Plug-in 4/160 14TE 173 70.78 155 66.18 167 131 C0735-22A 4HE Plug-in 4/160 15TE 173 75.86 155 71.26 167 131 *C0735-23A 4HE Plug-in 4/160 18TE 173 91.1 155 86.5 167 131 *C0735-24A 4HE Plug-in 4/160 21TE 173 106.34 155 101.74 167 131 *C0735-25A 4HE Plug-in 4/220 14TE 173 70.78 155 66.18 227 131 *C0735-29A 4HE Plug-in 4/220 15TE 173 75.86 155 71.26 227 131 *C0735-30A 4HE Plug-in 4/220 18TE 173 91.1 155 86.5 227 131 *C0735-31A 4HE Plug-in 4/220 21TE 173 106.34 155 101.74 227 131 *C0735-32A 4HE Plug-in 4/220 27TE 173 136.82 155 132.22 227 131 *C0735-33A * M.O.Q. (Minimum order quantity) www.apw.eu.com Tel: +39 011 7725024
Plug-in units 6HE EURO 90 modular plug-in units Front dimension This modular drawer can be fitted into 6U EURO 90 subrack or caseframe through four standard card guide (see 0577... part number). The plug-in unit allows one or two double 233.4 x 160, 233.4 x 220, 233.4 x 280 EURO cards that can be entered through grooves to the left or right. In the back panel there are 2 groves to be used for connections. Horizontal or vertical drawer covers are supplied upon request. Contents of kit Qty Material Front panel 1 Alodine 1000 Rear panel 1 Alodine 1000 Side extrusion 4 Alodine 1000 Extruded handle 1 Alodine 1000 Fixings Side view Rear view Unit A B C D 6HE Plug-in 6/160 14TE 70.78 167 66.18 39.68 C0735-64A 6HE Plug-in 6/160 15TE 75.86 167 71.26 44.94 C0735-65A 6HE Plug-in 6/160 18TE 91.1 167 86.5 60.18 *C0735-66A 6HE Plug-in 6/160 21TE 106.34 167 101.74 75.42 C0735-67A 6HE Plug-in 6/220 14TE 70.78 227 66.18 39.68 C0735-71A 6HE Plug-in 6/220 15TE 75.86 227 71.26 44.94 C0735-72A 6HE Plug-in 6/220 18TE 91.1 227 86.5 60.18 *C0735-73A 6HE Plug-in 6/220 21TE 106.34 227 101.74 75.42 C0735-74A 6HE Plug-in 6/280 14TE 70.78 287 66.18 39.68 C0735-78A 6HE Plug-in 6/280 15TE 75.86 287 71.26 44.94 C0735-79A 6HE Plug-in 6/280 18TE 91.1 287 86.5 60.18 *C0735-80A 6HE Plug-in 6/280 21TE 106.34 287 101.74 75.42 C0735-81A * M.O.Q. (Minimum order quantity)
Front panel 3HE - 6HE modular front panel EURO 90 13 The aluminium front panel has an Alodine 1000 treated surface that is mechanically fixed to the card. The card can be fitted through a noryl V0 bracket. It is assembled on EURO 90 subrack and caseframe through a special fast turn screws without the use of a tapped strips. Contents of kit - 3U Qty Front panel 0729... 1 Noryl bracket 0730 1 Handle C0733... 1 Fast turn special screw C0725 2 Fixings Contents of kit - 6U Qty Front panel 0729... 1 Noryl bracket 0730 2 Handle C0733... 2 Fast turn C0725 2 Fixings Unit A B C 3HE Front panel 3TE 14.9 - - *C0731-03A 3HE Front panel 4TE 19.98 - - C0731-04A 3HE Front panel 5TE 25.06 - - *C0731-05A 3HE Front panel 6TE 30.14 15.24 - C0731-06A 3HE Front panel 7TE 35.22 20.32 - C0731-07A 3HE Front panel 8TE 40.3 20.32 24.4 C0731-08A 3HE Front panel 9TE 45.38 30.48 30.48 C0731-09A 3HE Front panel 10TE 50.46 35.36 35.36 C0731-10A 6HE Front panel 3TE 14.9 - - *C0731-53A 6HE Front panel 4TE 19.98 - - *C0731-54A 6HE Front panel 5TE 25.06 - - *C0731-55A 6HE Front panel 6TE 30.14 15.24 - C0731-56A 6HE Front panel 7TE 35.22 20.32 - C0731-57A 6HE Front panel 8TE 40.3 24.4 25.4 C0731-58A 6HE Front panel 9TE 45.38 30.48 30.48 *C0731-59A 6HE Front panel 10TE 50.46 35.36 35.56 *C0731-60A * M.O.Q. (Minimum order quantity) www.apw.eu.com Tel: +39 011 7725024
Modular front panel Modular front panel EURO 90 3HE / 6HE This series of aluminium front panels in Alodine 1000 treated surface completes the range from page 270. The card can be fitted through a noryl V0 bracket. It is assembled on EURO 90 subrack and caseframe through a fast turn special screw without the use of tapped strips. The following models have a larger range of modular front panels available. 0730 (kit C-0757) Contents of kit - 3U Qty Front panel 0729... 1 Noryl bracket 0730 2 Handle C0733... 1 Fast turn special screw C0725 4 Fixings Contents of kit - 6U Qty Front panel 0729... 1 Noryl bracket 0730 4 Handle C0733... 2 Fast turn C0725 4 Fixings Material: Alluminium 2.5 mm Material: Alluminium 2.5 mm Unit A 3HE Modular front panel 11TE 55.54 *C0731-11A 3HE Modular front panel 12TE 60.62 C0731-12A 3HE Modular front panel 14TE 70.78 C0731-14A 3HE Modular front panel 15TE 75.86 *C0731-15A 3HE Modular front panel 16TE 80.94 C0731-16A 3HE Modular front panel 18TE 91.1 C0731-18A 3HE Modular front panel 20TE 101.26 *C0731-20A 3HE Modular front panel 21TE 106.34 C0731-21A 3HE Modular front panel 27TE 136.82 *C0731-27A 3HE Modular front panel 28TE 141.9 *C0731-28A Unit A 6HE Modular front panel 11TE 55.54 *C0731-61A 6HE Modular front panel 12TE 60.62 *C0731-62A 6HE Modular front panel 14TE 70.78 *C0731-64A 6HE Modular front panel 15TE 75.86 *C0731-65A 6HE Modular front panel 16TE 80.94 *C0731-66A 6HE Modular front panel 18TE 91.1 *C0731-68A 6HE Modular front panel 20TE 101.26 *C0731-70A 6HE Modular front panel 21TE 106.34 *C0731-71A 6HE Modular front panel 27TE 136.82 *C0731-77A 6HE Modular front panel 28TE 141.9 *C0731-78A * M.O.Q. (Minimum order quantity)
Accessories Extruded handle This new series of handles has a modern design and is composed of two noryl moulding supports, one strong grip handle, a plastic cover and all fixing. 15 A B 2U extruded handle EURO-90 72.7 57.7 C1080-02A 3U extruded handle EURO-90 117.1 102.1 C1080-03A 4U extruded handle EURO-90 161.6 146.6 C1080-04A 6U extruded handle EURO-90 250.5 235.5 C1080-06A Front panel Having only the standard sight hole and retaining screw holes, this panel has no handles, leaving the area completely free. They can also be used at the rear of the subrack. Please do not forget to order tapped strip. A B Weight (Kg) 42TE 2U 213 84 0.135 C0597-02A 42TE 3U 213 128.5 0.205 C0597-03A 42TE 4U 213 173 0.265 C0597-04A 42TE 6U 213 261.9 0.395 C0597-06A 60TE 2U 304.5 84 0.187 C0597-12A 60TE 3U 304.5 128.5 0.280 C0597-13A 60TE 4U 304.5 173 0.389 C0597-14A 60TE 6U 304.5 261.9 0.560 C0597-16A 84TE 2U 426.3 84 0.265 C0597-32A 84TE 3U 426.3 128.5 0.416 C0597-33A 84TE 4U 426.3 173 0.553 C0597-34A 84TE 6U 426.3 261.9 0.830 C0597-36A Divider kit For use with 6U subracks, this divider kit provides a useful way to mix 3U and 6U board heights within a unit. The divider kit is available in two different widths 42TE an 60TE. Contents of kit Qty Material Divider plate 2 Alluminio Front panel 2TE with 2 front extrusion and 2 rear extrusion 1 Fixings Code Front Rear A 6U 42TE H = 90 divider kit 1034-04 1037-04 218.44 C1090-02A 6U 42TE H = 122.4 divider kit 1034-04 1041-04 218.44 C1090-05A 6U 60TE H = 90 divider kit 1034-03 1037-03 309.88 C1090-12A 6U 60TE H = 122.4 divider kit 1034-03 1041-03 309.88 C1090-15A www.apw.eu.com Tel: +39 011 7725024
Accessories Horizontally and vertically hinged panels The whole panel consists of an aluminium 25/10 Alodine 1000, an aluminium side border that runs the length of the panel, two blocks made with hinges made of nylon 66% and vetro 3%. Typically used in situations where quick access is needed to equipment, but do not want to remove the panel completely. Supplied with 1/4 rotary locks as standard. Panels with predrilled holes designed by the client and aluminium side borders in 1 mt. size are available upon request. Code(0551) The border is treated with 1000 Alodine while the blocks are black. Code N. C0620... Code N. C0625... A B Orizontal type Vertical type Weight Kg Weight Kg 2U 42TE horizontally and vertically hinged panel 213.3 84 0.250 *C0620-02A 0.226 *C0625-02A 3U 42TE horizontally and vertically hinged panel 213.2 128.5 0.300 C0620-03A 0.296 *C0625-03A 4U 42TE horizontally and vertically hinged panel 213.2 173 0.350 *C0620-04A 0.342 *C0625-04A 6U 42TE horizontally and vertically hinged panel 213.2 261.9 0.450 C0620-06A 0.483 *C0625-06A 2U 84TE horizontally and vertically hinged panel 426.4 84 0.439 *C0620-32A 0.347 *C0625-32A 3U 84TE horizontally and vertically hinged panel 426.4 128.5 0.570 C0620-33A 0.480 C0625-33A 4U 84TE horizontally and vertically hinged panel 426.4 173 0.701 *C0620-34A 0.613 *C0625-34A 6U 84TE horizontally and vertically hinged panel 426.4 261.9 0.963 C0620-36A 0.879 C0625-36A * M.O.Q. (Minimum order quantity) Rear cover kit Suitable for EURO 90 subrack, available in 3U height (2 for the 6U version). It is typically used to protect connector and wiring at back of the subrack. Produced with 15/10 treated aluminium Alodi ne. It is supplied with 4, A 055 square rotating bolts and fixing screws. Subrack rear cover kit C1060-A
Accessories Card guides These card guides are produced using light blue V0 noryl and are available in three different lengths. The insertion on the aluminium extrusion is very fast and secure. Compatible with PCBS from 1.6 to 2 mm thickness. 17 Normal card guides A B 1 pc. 10 pcs. kit 50 pcs. kit 141.4 123.4 C0577-01 C0577-0110 C0577-0150 201.4 183.4 C0577-02 C0577-0210 C0577-0250 Reinforced card guides A B 1 pc. 10 pcs. kit 50 pcs. kit 201.4 183.4 C0577-12 C0577-1210 C0577-1250 Reinforced card guides A B 1 pc. 10 pcs. kit 50 pcs. kit 261.4 243.4 C0577-13 C0577-1310 C0577-1350 www.apw.eu.com Tel: +39 011 7725024
Accessories SUBRACK COVER Top and base cover kits This range of top and base covers is suitable for fitting to EURO 90 subracks. Three depths are available for protecting guide area of 160 mm, 220 mm or 280 mm boards. The covers are available in a ventilated version. The plastic insert (0574) has to be mounted on the extrusion before the subrack can be assembled. A Weight Kg C/160 84TE 162 0.400 C1105-01A C/220 84TE 222 0.500 C1105-02A C/280 84TE 282 0.700 C1105-03A C/160 42TE 162 0.200 C1105-11A C/220 42TE 222 0.250 C1105-12A C/280 42TE 282 0.350 C1105-13A Plastic insert Code 0574 Plastic sleeve The plastic sleeve cover is necessary to keep in place the front panel screw and knob so they won t become loose. It also acts as protection against panel scratching. Plastic bush A0611 Special screw to fix panels This 2.5MA special screw has to be used with the plastic sleeve for fixing front panels to the EURO 90 subrack or caseframe through the tapped strips (code 0591 page 279). Material: nicholed steel. Special screw to fix panels A0613-NIC Special knob This 2.5MA special knob has the same functions of the special screw P/N 0613 and is supplied with hinged front panel. Material: nicholed steel. Special knob A0612-NIC
Accessories TAPPED STRIPS To fix front panels 19 The fixing strips are made of 5x2 flat brass 2.5MA and perforated in holes at a distance of M2.5 at 5.08 mm. Tapped strip are ordered separately and are required to fix unforeseen front panels or backplane onto the subrack. N. holes A Weight Kg 84TE tapped strip 84 426.6 0.035 0591-01ZIN 60TE tapped strip 60 304.7 0.025 0591-03ZIN 42TE tapped strip 42 213.3 0.018 0591-04ZIN INTERNAL SHELVES EURO 90 horizontal shelves The horizontal shelf is made with 15/10 aluminium treated alodine 1000 and is folded on four sides. Can be fixed on the inside the subrack or case frame, all fixing screws are included. A B Weight Kg 42 TE/160 218 164 0.180 C1066-01A 42 TE/220 218 224 0.240 C1066-02A 42 TE/280 218 284 0.300 C1066-03A 84 TE/160 431.3 164 0.400 C1066-31A 84 TE/220 431.3 224 0.480 C1066-32A 84 TE/280 431.3 284 0.560 C1066-33A 84 TE/340 431.3 344 0.640 C1066-34A Plug-in insulating spacer The isolating spacers are useful for attaching the card to the modular drawer.the depth is adaptable for DIN 41612 and DIN 41617. Material: Black Macralon. Plugh-in insulating spacer A0745 Backplane insulating spacer strip Backplane insulating spacer strip Material: V0 light blue noryl. Spacer strips are needed to insulate the backplane and to provide the correct depth dimension of PCB and plug-in modules. Backplane insulating spacer strip 0755 www.apw.eu.com Tel: +39 011 7725024
Accessories 1/4 rotary lock with defined stop This 1/4 rotary lock can only be used on our EURO 80, EURO 90 subracks and caseframes. Tapped strips are not needed to lock a panel. It is located externally with a plastic receptacle, internally with a spring that gives blocking elasticity at the hinge. 1/4 Rotary lock C0725 Extruded modular handle 1/4 Rotary lock Contents of kit Qty Material Extruded handle 1 Alodine 1000 Fixing insert 1 / 2 2.5 x 8 TC fixing screws 1 / 2 2.5 x 8 TSCR fixing screws 1 / 2 A EURO 90 modular handle 3TE 14.1 C0733-03A EURO 90 modular handle 4TE 19.18 C0733-04A EURO 90 modular handle 5TE 24.26 C0733-05A EURO 90 modular handle 6TE 29.34 C0733-06A EURO 90 modular handle 7TE 34.42 C0733-07A EURO 90 modular handle 8TE 39.5 C0733-08A EURO 90 modular handle 9TE 44.58 C0733-09A EURO 90 modular handle 10TE 49.66 C0733-10A EURO 90 modular handle 11TE 54.74 C0733-11A EURO 90 modular handle 12TE 59.82 C0733-12A EURO 90 modular handle 14TE 69.98 C0733-14A EURO 90 modular handle 15TE 75.06 C0733-15A EURO 90 modular handle 16TE 80.14 C0733-16A EURO 90 modular handle 18TE 90.3 C0733-18A EURO 90 modular handle 20TE 100.46 C0733-20A EURO 90 modular handle 21TE 105.54 C0733-21A EURO 90 modular handle 27TE 136.02 C0733-27A EURO 90 modular handle 28TE 141.1 C0733-28A Card mounting brackets Card mounting brackets 0608-CRO Card mounting brackets
SISTEMA EURO 90 Various Brushed stainless steel handle 21 Handle 32mm height, 74mm length, 64mm wheelbase, 10mm diameter. * Handle 32mm height, 106mm length, 96mm wheelbase, 10mm diameter. * Handle 32mm height, 138mm length, 128mm wheelbase, 10mm diameter. * Handle 32mm height, 170mm length, 160mm wheelbase, 10mm diameter. * Handle 32mm height, 298mm length, 288mm wheelbase, 10mm diameter. * Handle 32mm height, 362mm length, 352mm wheelbase, 10mm diameter. * *M4 fixing not included MS32-074-10 MS32-106-10 MS32-138-10 MS32-170-10 MS32-298-10 MS32-362-10 Brushed stainless steel handle L B A d d1 MS32-074-10 74 64 32 10 M4 MS32-106-10 106 96 32 10 M4 MS32-138-10 138 128 32 10 M4 MS32-170-10 170 160 32 10 M4 MS32-298-10 298 288 32 10 M4 MS32-362-10 362 352 32 10 M4 www.apw.eu.com Tel: +39 011 7725024
GOMA ELETTRONICA SpA 10146 Torino - Italy Via Carlo Capelli, 89 Tel: +39 011 7725024 Fax: +39 011 712298 www.gomaelettronica.it All trademarks are the property of their respective owners GOMA ELETTRONICA SpA MKA-CTG-EN 0517