036-21023-002 Rev A (5/00) TECHNICAL GUIDE 16 SEER 2-5 TON CONDITIONING SPLIT-SYSTEM COOLING DESCRIPTION The HTS Stealth series condensing units use Twin Single compressor technology to provide cooling efficiencies up to 16.7 SEER. They are to be installed with the matching variable speed Enhancer air handler or Diamond furnace, or with a two-stage or single-stage indoor unit, a corresponding coil and sweat connect lines. A factory specified balanced port hard shut-off TXV kit must be used for proper installation and optimum performance. These units are backed by a 10 - year limited warranty on the compressor and 1 - year on all other parts. FEATURES QUALITY CONDENSER COILS - The coil is constructed of copper tube and hardened aluminum fins for durability and long lasting efficient operation. The fins on the unit are protected with a decorative grille. DURABLE FINISH - Cabinet is made of powder painted steel over prepainted primer. The pre-treated flat galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and glossy earth tone finish insure less fading when exposed to sunlight. This finish has been tested to provide 1/3 greater protection than conventional units. PROTECTED COMPRESSORS - The Twin Single compressor is protected against high and low pressure. Hard start components are included to ensure start-up under adverse conditions. All models have standard crankcase heat for added protection. OPTIMUM PERFORMANCE - The solid-state electronic controlboard optimizes the compressor staging based on load requirements, provides a 5-minute anti-short cycle timer for each compressor, and simplifies troubleshooting with built in self diagnostics. LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. All units contain enough refrigerant for the smallest matching indoor coil and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof. EFFECTIVE HUMIDITY CONTROL - The inherent design of the Stealth system and the staging operation of the Twin Single compressor provide effective humidity control at the lowest possible operating cost. An optional dehumidification control accessory is available to maintain the humidity at a set desired level. TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications. LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise up away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. MODELS: H4TS024 H4TS030 H4TS036 H4TS048 H4TS060 LOW MAINTENANCE - Long life permanently lubricated motor- bearings need no annual servicing. EASY SERVICE ACCESS - Fully exposed refrigerant connections and a single panel covering the electrical controls make servicing easy. Easy access for coil clearing is also provided. RE-USABLE SERVICE VALVES - Provided on both the liquid and vapor sweat connections for ease of evacuating and charging. FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
Table 1: COOLING CAPACITY - Variable Speed Air Handler UNIT MODEL VAR SPEED HANDLER MODEL ELEC. HEAT H4TS024 N+VSB12 5,7.5,10,15,18 17 H4TS030 W N-VSB12 5,7.5,10,15,18 17 COIL MODEL G+FD024S17 G+FD030S17 G+FD036S17 G+FD030S17 G+FD036S17 N-VSC16 5,7.5,10,15,20 21 G+FD042S21 H4TS036 N-VSC16 5,7.5,10,15,20 21 H4TS048 H4TS060 N-VSC16 N-VSD20 N-VSD20 5, 7.5,10,15,20 5, 7.5,10,15,20 5, 7.5,10,15,20 1. See notes on page 5. G+FD036S21 G+FD042S21 G+FD048S21 21 G+FD048S21 24 24 G+FD048S24 G+FD060S24 G+FD060S24 G+FD061H24 STAGE RATED TOTAL CAP COOLING SENS. SYSTEM EER 1 1 600 12.4 10.0 0.92 2 820 24.0 16.8 2.00 12.0 1 600 12.8 10.2 0.91 14.0 2 820 24.6 17.2 1.97 12.5 1 600 13.0 10.4 0.91 14.3 2 820 25.0 17.5 2.00 12.5 1 670 12.0 1.09 13.7 2 1035 30.0 21.6 2.59 11.6 1 670 15.4 12.2 1.12 13.7 2 1035 31.0 22.0 2.67 11.6 1 690 16.4 13.4 1.14 14.4 2 1065 31.6 23.4 2.68 11.8 1 770 20.0 16.0 1.46 13.7 2 1185 35.0 26.0 2.97 11.8 1 770 20.0 16.0 1.46 13.7 2 1185 35.0 26.0 2.97 11.8 1 770 20.6 16.6 1.43 14.4 2 1185 36.0 26.6 2.88 12.5 1 1050 25.0 20.0 1.72 2 1605 49.0 36.0 4.45 11.0 1 1050 25.0 20.0 1.72 2 1570 49.0 36.0 4.45 11.0 1 1050 25.0 21.0 1.79 14.0 2 1570 50.0 37.5 4.46 11.2 1 1250 33.0 26.4 2.44 2 1900 59.0 43.0 5.67 10.4 1 1250 33.0 26.4 2.36 14.0 2 1900 59.5 44.0 5.56 10.7 SEER 16.0 16.2 16.0 16.0 16.0 16.0 16.0 16.0 SOUND RATINGS SOUND RATINGS UNIT MODEL SOUND RATING DECIBELS H4TS 024 72 H4TS 030 72 H4TS 036 74 H4TS 048 78 H4TS 060 78 2 Unitary Products Group
Table 2: COOLING CAPACITY - Single Speed Furnace UNIT MODEL H4TS024 H4TS030 H4TS036 H4TS048 H4TS060 SINGLE SPEED FURNACE NOMINAL FLOW 800 1000 1200 1000 1200 1400 1200 1400 1600 1600 2000 2000 COIL MODEL W STAGE RATED TOTAL CAP COOLING SENS. SYSTEM EER 1 14,17 1 600 12.0 10.0 0.95 12.6 G+UA036S14,16,21 21 2 800 24.0 17.2 2.26 10.6 17 G+UA048S17 G+HD036 17 G+FD030S17 17 G+FD036S17 17,21 G-UA048S17,21 G1HD036 G1HD048 17 G+FD036S17 21 G+FD042S21 17 G+FD046S17 G+HD048 17,21 G+UA048S17,21 17,21 G+FD036S17,21 21 G+FD042S21 17 G+FD046S17 21,24 G-FD048S21,24 G+HD060 21 G+UA048S21 21,24 G+UA060S21,24 21,24 G+FD048S21,24 24 G+FD060S24 G+HD060 21,24 G+UA060S21,24 24 G+FD060S24 24 G+FD061H24 1 600 12.4 10.4 0.95 13.0 2 800 24.4 17.6 2.22 11.0 1 600 12.2 10.2 0.97 12.6 2 800 24.4 17.6 2.30 10.6 1 600 12.2 10.2 0.97 12.6 2 800 24.0 17.2 2.26 10.6 1 600 12.4 10.4 0.98 12.6 2 800 24.4 17.6 2.22 11.0 1 650 15.4 13.4 1.22 12.6 2 1000 32.0 23.6 2.91 11.0 1 650 12.2 1.27 11.8 2 1000 30.0 22.0 2.94 10.2 1 650 15.4 13.4 1.22 12.6 2 1000 32.0 23.6 2.91 11.0 1 650 12.2 1.27 11.8 2 1000 30.0 22.0 2.94 10.2 1 650 15.2 13.4 1.27 12.0 2 1000 30.6 23.4 2.89 10.6 1 650 12.2 1.27 11.8 2 1000 30.0 22.0 2.94 10.2 1 750 20.0 16.6 1.67 12.0 2 1200 35.0 26.6 3.18 11.0 1 750 19.2 16.6 1.60 12.0 2 1200 35.0 26.6 3.18 11.0 1 750 19.2 16.0 1.66 11.6 2 1200 34.0 26.0 3.27 10.4 1 750 19.2 16.0 1.66 11.6 2 1200 34.0 26.0 3.27 10.4 1 750 19.2 16.0 1.66 11.6 2 1200 34.0 26.0 3.27 10.4 1 750 20.0 16.6 1.67 12.0 2 1200 35.0 26.6 3.13 11.2 1 1050 24.4 20.0 2.00 12.2 2 1600 49.0 37.5 4.67 10.5 1 1050 24.4 20.0 2.00 12.2 2 1600 48.0 36.0 4.71 10.2 1 1050 24.0 20.0 1.97 12.2 2 1600 48.0 36.0 4.71 10.2 1 1050 24.0 20.0 1.97 12.2 2 1600 48.0 36.0 4.71 10.2 1 1050 24.4 21.0 2.00 12.2 2 1600 49.0 37.5 4.67 10.5 1 1250 32.0 26.4 2.67 12.0 2 1900 58.0 43.0 5.69 10.2 1 1250 32.0 26.4 2.67 12.0 2 1900 58.0 43.0 5.69 10.2 1 1250 32.0 26.4 2.67 12.0 2 1900 58.0 43.0 5.69 10.2 1 1250 32.4 26.4 2.70 12.0 2 1900 58.5 44.0 5.74 10.2 SEER 13.6 14.0 13.6 13.6 14.0 13.0 14.0 13.0 13.0 13.0 13.0 13.0 14.0 14.0 14.0 14.0 14.0 1. See notes on page 5. Unitary Products Group 3
Table 3: COOLING CAPACITY - Variable Speed Furnace UNIT MODEL VARIABLE SPEED FURNACE MODEL W COIL MODEL 1 STAGE RATED TOTAL CAP COOLING 2 SENS. SYSTEM EER 3 SEER H4TS024 H4TS030 P1XUB12V055 17 P1DUA12V064 14 P1XUB12V055 17 P1XUC16V075 21 G+UA036S17 G+FD024S17 G+FD030S17 G-FD036S17 G+FD046S17 G+UA030S14 G+UA036S14 G1UA036S17 G1UA048S17 G2FD030S17 G2FD036S17 G2FD046S17 G1UA036S21 G1UA048S21 G2FD036S21 G2FD042S21 G2FD048S21 P1DUA12V064 17 G1UA036S14 P1DUB16V080 17 G1UA036S17 G1UA048S17 G2FD030S17 G2FD036S17 G2FD046S17 1 600 12.6 10.2 0.92 13.7 2 820 24.4 17.2 2.09 11.7 1 600 12.4 10.2 0.95 13.0 2 820 23.8 16.8 2.07 11.5 1 600 12.6 10.2 0.93 2 820 24.4 17.2 2.10 11.6 1 600 12.8 10.2 0.93 13.7 2 820 25.0 17.4 2.14 11.7 1 600 12.8 10.4 0.93 13.7 2 820 25.0 17.4 2.14 11.7 1 600 12.4 10.0 0.95 13.0 2 820 23.8 16.8 2.11 11.3 1 600 12.6 10.2 0.92 13.7 2 820 24.4 17.2 2.09 11.7 1 670 15.4 13.4 1.18 13.0 2 1035 29.8 21.6 2.68 11.1 1 670 12.2 1.13 13.3 2 1035 29.6 21.6 2.62 11.3 1 670 15.4 12.2 1.18 13.0 2 1035 29.8 21.6 2.71 11.0 1 670 12.0 1.15 13.0 2 1035 29.6 21.6 2.69 11.0 1 670 12.0 1.15 13.0 2 1035 29.6 21.6 2.69 11.0 1 690 12.0 1.15 13.0 2 1065 29.6 21.6 2.69 11.0 1 690 15.4 12.2 1.18 13.0 2 1065 29.4 21.4 2.67 11.0 1 670 15.4 12.2 1.18 13.0 2 1065 29.4 21.4 2.67 11.0 1 690 16.0 13.0 1.15 13.9 2 1065 31.4 23.0 2.75 11.4 1 690 16.0 13.0 1.15 13.9 2 1065 31.4 23.0 2.75 11.4 1 670 15.4 12.2 1.19 13.0 2 1035 30.2 22.0 2.75 11.0 1 670 15.4 12.2 1.18 13.0 2 1035 29.8 21.6 2.71 11.0 1 670 12.0 1.13 13.3 2 1035 29.6 21.6 2.64 11.2 1 670 12.0 1.15 13.0 2 1035 29.8 21.6 2.71 11.0 1 670 12.0 1.14 13.2 2 1035 29.6 21.6 2.69 11.0 1 670 12.0 1.14 13.2 2 1035 29.6 21.6 2.64 11.2 4 Unitary Products Group
Table 3: COOLING CAPACITY - Variable Speed Furnace (Continued) UNIT MODEL VARIABLE SPEED FURNACE MODEL W COIL MODEL 1 STAGE RATED TOTAL CAP COOLING 2 SENS. SYSTEM EER 3 SEER H4TS036 H4TS048 H4TS060 P1XUB12V055 P1DUB16V080 17 17 P1XUC16V075 21 P1XUC20V095 P1DUC20V096 21 G1UA048S17 G2FD036S17 G2FD046S17 G1UA048S21 G2FD036S21 G2FD042S21 G2FD048S21 G1UA048S21 G2FD036S21 G2FD042S21 G2FD048S21 P1XUD20V112 24 G2FD048S24 P1XUC16V075 P1XUC20V095 P1DUC20V096 21 P1XUD20V112 24 P1XUC20V095 P1DUC20V096 P1XUD20V112 24 G-UA048S21 G-UA060S21 G-FD048S21 G-FD048S24 G-UA060S24 G-FD060S24 21 G-UA060S21 G-UA060S24 G-FD060S24 G-FD061H24 1 750 20.0 16.0 1.49 13.4 2 1150 34.8 26.0 3.08 11.3 1 750 20.0 16.0 1.49 13.4 2 1150 34.8 26.0 3.08 11.3 1 750 20.0 16.0 1.49 13.4 2 1150 34.8 26.0 3.08 11.3 1 770 21.0 16.6 1.49 14.1 2 1185 36.8 27.0 3.17 11.6 1 770 20.4 16.0 1.50 13.6 2 1185 35.4 26.0 3.11 11.4 1 770 20.4 16.0 1.50 13.6 2 1185 35.4 26.0 3.11 11.4 1 770 21.0 16.6 1.49 14.1 2 1185 36.8 27.0 3.17 11.6 1 770 21.0 16.0 1.47 14.3 2 1200 37.0 27.0 3.19 11.6 1 770 20.4 16.4 1.49 13.7 2 1200 35.4 26.0 3.11 11.4 1 770 20.4 16.4 1.49 13.7 2 1200 35.4 26.0 3.11 11.4 1 770 21.0 16.6 1.48 14.2 2 1200 37.0 27.0 3.19 11.6 1 770 21.0 16.6 1.48 14.2 2 1200 37.0 27.0 3.19 11.6 1 1050 25.0 1.75 14.3 2 1600 49.0 36.0 4.54 10.8 1 1050 26.0 21.0 1.82 14.3 2 1600 51.0 37.5 4.72 10.8 1 1050 25.0 20.0 1.75 14.3 2 1600 49.0 36.0 4.54 10.8 1 1050 25.0 20.0 1.75 14.3 2 1600 49.0 36.0 4.54 10.8 1 1050 26.0 21.0 1.82 14.3 2 1600 51.0 37.5 4.72 10.8 1 1050 26.0 21.0 1.82 14.3 2 1600 51.0 37.5 4.72 10.8 1 1250 33.0 26.4 2.52 13.1 2 1900 59.0 43.0 5.67 10.4 1 1250 33.0 26.4 2.52 13.1 2 1900 59.0 43.0 5.67 10.4 1 1250 33.0 26.4 2.52 13.1 2 1900 59.0 43.0 5.67 10.4 1 1250 34.0 27.0 2.54 13.4 2 1900 60.0 44.0 5.66 10.6 1. Refer to coil installation guide for proper coil application. 2. Standard cooling operation is limited to 45 F outdoor ambient. 3. EER (Energy Efficiency Ratio) is the total cooling output in BTU s at a 95 F outdoor ambient divided by the total electric power in watt-hours at those conditions. Certified in accordance with the Unitary Small Equipment certification program which is based on ARI Standard 210/240 based on 80 F entering air temperature, 50% RH, and rated air flow includes compressor, outdoor fan and indoor blower motor watts. Add-on coils include 365 watts/1000 for blowr motor. Unitary Products Group 5
Table 4: SYSTEM COOLING CAPACITY - 1 Cylinder 1 H4TS024 / G+FD024S14, 17 600 650 CONDENSER ENTERING TEMPERATURE 85/72 14.9 10.1 0.69 14.3 10.0 0.77 9.70 0.85 12.7 9.40 0.93 11.9 9.20 1.00 80/67 13.7 10.2 0.69 13.0 9.90 0.77 12.3 9.60 0.84 11.6 9.30 0.91 10.8 9.00 0.98 75/62* 12.4 10.1 0.69 11.8 9.80 0.76 11.3 9.60 0.83 10.7 9.10 0.90 10.0 8.60 0.96 70/57 11.5 9.80 0.69 10.9 9.30 0.76 10.4 8.90 0.82 9.80 8.40 0.89 9.20 7.90 0.95 85/72 15.2 10.7 0.69 14.4 10.4 0.77 13.6 10.1 0.85 12.8 9.90 0.93 12.0 9.60 1.00 80/67 13.8 10.6 0.69 13.8 10.3 0.77 12.4 10.0 0.84 11.7 9.70 0.91 11.1 9.40 0.98 75/62* 12.5 10.5 0.69 12.1 10.3 0.76 11.4 9.80 0.83 10.8 9.30 0.90 10.2 8.70 0.97 70/57 11.7 10.0 0.69 11.1 9.50 0.76 10.5 9.00 0.82 9.90 8.50 0.89 9.30 8.00 0.95 85/72 15.3 11.1 0.69 10.8 0.77 13.7 10.5 0.85 12.9 10.3 0.93 12.0 10.0 1.00 80/67 13.9 11.0 0.69 13.2 10.7 0.76 12.5 10.4 0.84 11.9 10.2 0.92 11.2 9.60 0.99 75/62* 12.8 11.0 0.69 12.2 10.4 0.76 11.6 9.90 0.83 10.9 9.40 0.90 10.3 8.80 0.97 70/57 11.8 10.1 0.69 11.2 9.60 0.76 10.6 9.10 0.83 10.0 8.60 0.89 9.40 8.00 0.95 H4TS024 / G+FD030S17 600 650 85/72 15.4 10.3 0.68 14.7 10.2 0.76 13.9 9.90 0.84 13.1 9.60 0.92 12.3 9.30 0.99 80/67 14.2 10.3 0.68 13.4 10.1 0.75 12.7 9.80 0.83 11.9 9.50 0.90 11.2 9.20 0.97 75/62* 12.9 10.3 0.68 12.2 10.0 0.75 11.7 9.80 0.82 11.0 9.30 0.89 10.4 8.70 0.95 70/57 11.9 10.0 0.68 11.3 9.50 0.75 10.7 9.00 0.81 10.1 8.50 0.88 9.50 8.00 0.94 85/72 15.6 10.9 0.68 14.8 10.6 0.76 14.0 10.3 0.84 13.2 10.0 0.92 12.3 9.70 0.99 80/67 14.3 10.8 0.68 13.6 10.5 0.75 12.8 10.2 0.83 12.0 9.90 0.90 11.4 9.60 0.97 75/62* 13.0 10.7 0.68 12.4 10.5 0.75 11.8 10.0 0.82 11.2 9.40 0.89 10.5 8.80 0.95 70/57 12.1 10.2 0.68 11.5 9.70 0.75 10.9 9.20 0.81 10.3 8.80 0.88 9.60 8.10 0.94 85/72 15.7 11.3 0.68 14.9 11.0 0.76 14.1 10.7 0.84 13.3 10.5 0.92 12.4 10.2 0.99 80/67 14.4 11.2 0.67 13.6 10.9 0.75 12.9 10.6 0.83 12.3 10.3 0.90 11.5 9.7 0.98 75/62* 13.3 11.2 0.68 12.6 10.6 0.75 12.0 10.1 0.82 11.3 9.50 0.89 10.6 8.90 0.96 70/57 12.2 10.3 0.68 11.6 9.8 0.75 11.0 9.3 0.81 10.4 8.70 0.88 9.70 8.20 0.94 H4TS024 / G+FD036S17 6 Unitary Products Group
Table 4: SYSTEM COOLING CAPACITY - 1 Cylinder 1 (Continued) 600 650 85/72 15.7 10.4 0.69 14.8 10.2 0.77 14.1 10.0 0.86 13.3 9.80 0.94 12.4 9.50 1.01 80/67 14.4 10.5 0.69 13.7 10.2 0.77 12.9 9.90 0.85 12.1 9.70 0.92 11.3 9.40 0.99 75/62* 13.1 10.5 0.69 12.4 10.2 0.77 11.8 9.90 0.84 11.2 9.40 0.91 10.5 8.80 0.97 70/57 12.1 10.1 0.69 11.5 9.60 0.76 10.9 9.10 0.83 10.3 8.60 0.89 9.70 8.10 0.96 85/72 15.9 11.0 0.69 15.1 10.8 0.78 14.2 10.5 0.86 13.4 10.2 0.94 12.5 9.90 1.01 80/67 10.9 0.69 13.8 10.7 0.77 13.0 10.4 0.85 12.2 10.1 0.92 11.6 9.70 0.99 75/62* 13.3 11.1 0.69 12.7 10.6 0.77 12.0 10.1 0.84 11.4 9.50 0.91 10.7 8.90 0.98 70/57 12.3 10.3 0.69 11.7 9.80 0.76 11.1 9.30 0.83 10.4 8.70 0.90 9.80 8.20 0.96 85/72 16.0 11.5 0.69 15.2 11.2 0.78 14.3 11.0 0.86 13.4 10.7 0.94 12.6 10.4 1.01 80/67 14.6 11.4 0.69 13.9 11.1 0.77 13.2 11.0 0.85 12.4 10.4 0.92 11.7 9.80 1.00 75/62* 11.3 0.69 12.8 10.7 0.76 12.2 10.2 0.84 11.5 9.60 0.91 10.8 9.00 0.98 70/57 12.4 10.4 0.69 11.8 9.90 0.76 11.2 9.4 0.83 10.6 8.80 0.90 9.90 8.30 0.96 H4TS030 / G+FD030S17 650 85/72 18.2 12.3 0.87 17.3 12.0 0.97 16.3 11.7 1.07 15.4 11.4 1.16 14.4 11.0 1.25 80/67 16.7 12.2 0.87 15.8 11.9 0.97 14.9 11.5 1.06 14.0 11.2 1.14 13.3 10.9 1.23 75/62* 15.1 12.1 0.87 11.9 0.96 13.8 11.3 1.05 13.0 10.6 1.13 12.2 10.0 1.21 70/57 14.1 11.5 0.87 13.4 10.9 0.96 12.7 10.4 1.04 11.9 9.80 1.12 11.2 9.20 1.19 85/72 18.3 12.8 0.87 17.4 12.5 0.98 16.4 12.2 1.07 15.4 11.8 1.17 14.4 11.5 1.26 80/67 16.8 12.7 0.87 15.9 12.3 0.97 12.0 1.06 14.3 11.7 1.15 13.4 11.0 1.24 75/62* 15.4 12.6 0.87 14.7 12.0 0.96 14.0 11.4 1.05 13.2 10.8 1.14 12.4 10.1 1.22 70/57 14.2 11.6 0.88 11.1 0.96 12.8 10.5 1.04 12.1 9.90 1.12 11.3 9.30 1.19 85/72 18.5 13.7 0.88 17.6 13.4 0.98 16.6 13.1 1.08 15.7 12.9 1.18 14.8 12.1 1.27 80/67 16.9 13.6 0.88 16.3 13.3 0.98 15.4 12.6 1.07 14.6 11.9 1.16 13.7 11.2 1.25 800 75/62* 15.8 12.9 0.88 12.3 0.97 14.2 11.6 1.06 13.4 11.0 1.14 12.6 10.1 1.22 70/57 14.6 11.9 0.88 13.8 11.3 0.97 13.1 10.7 1.05 12.3 10.0 1.13 11.5 9.4 1.21 H4TS030 / G+FD036S21 650 85/72 18.5 12.4 0.88 17.6 12.1 0.98 16.6 11.9 1.08 15.7 11.6 1.17 14.8 11.3 1.27 80/67 17.0 12.4 0.88 16.2 12.1 0.98 15.3 11.8 1.07 14.4 11.4 1.16 13.6 10.9 1.24 75/62* 15.6 12.3 0.88 14.9 11.9 0.97 14.1 11.3 1.06 13.4 10.7 1.14 12.6 10.1 1.22 70/57 14.4 11.6 0.88 13.8 11.0 0.97 13.0 10.5 1.05 12.3 9.90 1.13 11.6 9.30 1.20 85/72 18.6 13.0 0.89 17.6 12.7 0.99 16.8 12.5 1.08 15.8 12.1 1.18 14.8 11.7 1.27 80/67 17.1 12.9 0.88 16.3 12.6 0.98 15.4 12.2 1.07 14.6 11.7 1.16 13.8 11.0 1.25 75/62* 15.8 12.7 0.89 15.1 12.1 0.98 14.3 11.5 1.06 10.8 1.15 12.7 10.2 1.23 70/57 14.6 11.7 0.89 13.9 11.2 0.97 13.2 10.6 1.05 12.4 10.1 1.13 11.7 9.30 1.21 85/72 18.9 14.0 0.89 17.9 13.7 0.99 16.9 13.3 1.09 16.1 12.9 1.19 15.1 12.1 1.29 80/67 17.4 13.8 0.89 16.6 13.3 0.99 15.8 12.6 1.08 14.9 11.9 1.17 14.0 11.2 1.26 800 75/62* 16.1 13.0 0.89 15.4 12.3 0.98 14.6 11.7 1.07 13.7 11.0 1.16 12.9 10.3 1.24 70/57 14.9 12.0 0.89 14.2 11.4 0.98 13.4 10.7 1.06 12.6 10.1 1.14 11.8 9.50 1.22 H4TS030 / G+FD042S21 650 CONDENSER ENTERING TEMPERATURE 85/72 19.8 13.6 0.90 18.7 13.3 1.01 17.7 13.0 1.11 16.7 12.7 1.21 15.7 12.4 1.30 80/67 18.1 13.6 0.90 17.2 13.3 1.00 16.3 12.9 1.10 15.3 12.5 1.19 12.0 1.27 75/62* 16.6 0.90 15.8 13.1 1.00 12.4 1.09 14.2 11.7 1.17 13.4 11.0 1.25 70/57 15.4 12.7 0.91 14.6 12.1 0.99 13.9 11.5 1.08 13.1 10.8 1.16 12.3 10.2 1.23 85/72 19.9 14.2 0.91 18.8 13.9 1.01 17.9 13.7 1.11 16.8 13.2 1.21 15.8 12.8 1.30 80/67 18.5 14.1 0.91 17.3 13.7 1.00 16.4 13.4 1.10 15.6 12.9 1.19 14.6 12.1 1.28 75/62* 16.8 13.9 0.91 16.0 13.3 1.00 15.2 12.6 1.09 14.4 11.9 1.18 11.2 1.26 70/57 15.6 12.9 0.91 14.8 12.2 1.00 14.0 11.6 1.08 13.2 10.9 1.16 12.4 10.2 1.24 Unitary Products Group 7
Table 4: SYSTEM COOLING CAPACITY - 1 Cylinder 1 (Continued) 85/72 20.1 15.4 0.91 19.1 1.02 18.0 14.6 1.12 17.1 14.1 1.22 16.1 13.3 1.32 80/67 18.5 15.1 0.91 17.7 14.6 1.01 16.8 13.9 1.11 15.8 13.1 1.20 14.9 12.3 1.30 800 75/62* 17.2 14.2 0.91 16.4 1.01 12.8 1.10 14.6 12.1 1.19 13.7 11.3 1.27 70/57 15.9 13.1 0.91 15.1 12.5 1.00 14.3 11.8 1.09 13.4 11.1 1.17 12.6 10.4 1.25 H4TS036 / G+FD036S21 750 85/72 23.2 15.1 1.17 22.7 15.4 1.27 21.7 1.38 20.6 15.2 1.50 19.3 14.8 1.62 80/67 21.1 1.19 20.8 1.29 19.9 15.4 1.39 18.7 15.2 1.51 17.5 14.7 1.62 75/62* 19.2 15.2 1.20 18.8 1.29 17.9 1.40 16.9 15.2 1.50 15.9 14.7 1.61 70/57 17.3 15.1 1.21 17.0 1.29 16.3 15.3 1.39 14.8 1.49 14.6 13.9 1.59 85/72 23.4 1.17 22.8 16.0 1.27 21.9 16.1 1.38 20.7 15.9 1.50 19.4 1.63 80/67 21.4 15.6 1.19 20.9 16.0 1.29 20.0 16.0 1.39 18.9 15.8 1.51 17.6 15.4 1.62 75/62* 19.4 15.7 1.20 18.9 16.0 1.29 18.1 16.1 1.40 17.1 15.8 1.50 16.1 15.3 1.61 70/57 17.5 15.7 1.21 17.2 15.9 1.30 16.6 15.8 1.39 15.7 1.50 14.8 14.1 1.60 85/72 23.7 16.4 1.16 23.2 17.2 1.26 22.2 17.3.38 20.9 17.1 1.50 19.6 16.7 1.63 80/67 21.8 16.6 1.19 21.2 17.0 1.28 20.2 17.1 1.39 19.1 17.0 1.51 17.9 16.5 1.63 850 75/62* 19.7 16.6 1.20 19.2 17.1 1.30 18.4 17.2 1.40 17.5 16.7 1.51 16.5 15.7 1.62 70/57 18.0 16.5 1.21 17.7 16.9 1.30 17.0 16.2 1.40 16.2 15.4 1.50 15.2 1.61 H4TS036 / G+FD042S21 750 85/72 23.4 15.2 1.17 22.8 1.27 21.7 15.4 1.38 20.6 15.3 1.50 19.3 14.8 1.62 80/67 21.3 15.1 1.19 20.7 15.4 1.29 19.9 15.4 1.39 18.7 15.1 1.51 17.5 14.7 1.62 75/62* 19.4 15.3 1.20 18.8 15.6 1.29 17.9 1.40 16.9 15.2 1.50 15.9 14.7 1.61 70/57 17.4 15.2 1.21 17.1 1.29 16.3 15.3 1.39 14.8 1.49 14.6 13.9 1.59 85/72 23.6 15.6 1.16 22.9 16.0 1.27 21.9 16.1 1.38 20.7 15.9 1.50 19.4 15.4 1.63 80/67 21.4 15.6 1.19 21.0 16.1 1.28 20.0 16.0 1.39 18.8 15.8 1.51 17.6 15.3 1.62 75/62* 19.5 15.8 1.20 19.0 16.1 1.29 18.1 16.1 1.40 17.1 15.8 1.50 16.1 15.3 1.61 70/57 17.6 15.7 1.21 17.3 16.0 1.30 16.6 15.8 1.39 15.7 1.50 14.8 14.2 1.60 85/72 23.9 16.7 1.16 23.3 17.2 1.26 22.2 17.2 1.38 20.9 17.1 1.50 19.5 16.6 1.63 80/67 21.9 16.7 1.18 21.3 17.1 1.28 20.2 17.1 1.39 19.0 17.0 1.51 17.9 16.5 1.63 850 75/62* 19.8 16.7 1.20 19.2 17.1 1.30 18.4 17.2 1.40 17.5 16.7 1.51 16.5 15.7 1.62 70/57 18.1 16.7 1.21 17.7 16.9 1.30 17.0 16.3 1.40 16.1 15.4 1.50 15.2 1.61 H4TS036 / G+FD048S21, 24 750 850 CONDENSER ENTERING TEMPERATURE 85/72 24.5 16.0 1.15 23.6 16.2 1.26 22.4 16.0 1.37 21.0 15.6 1.50 19.7 15.2 1.62 80/67 22.2 16.0 1.18 21.5 16.1 1.28 20.4 16.0 1.39 19.2 15.6 1.50 17.9 15.1 1.62 75/62* 20.2 16.1 1.19 19.5 16.3 1.29 18.5 16.0 1.39 17.3 15.7 1.50 16.2 15.2 1.61 70/57 18.3 16.1 1.20 17.6 16.1 1.29 16.8 16.0 1.39 15.9 15.3 1.49 14.4 1.59 85/72 24.7 16.5 1.15 23.8 16.8 1.25 22.6 16.7 1.37 21.2 16.3 1.50 19.8 15.9 1.62 80/67 22.4 16.5 1.18 21.7 16.8 1.28 20.6 16.6 1.39 19.3 16.2 1.50 18.1 15.8 1.62 75/62* 20.4 16.7 1.19 19.7 16.9 1.29 18.6 16.7 1.39 17.5 16.3 1.50 16.5 15.8 1.61 70/57 18.4 16.6 1.21 17.9 16.8 1.29 17.1 16.4 1.39 16.2 1.50 15.2 14.6 1.60 85/72 25.0 17.5 1.14 24.1 18.0 1.25 22.8 17.9 1.37 21.4 17.6 1.49 20.0 17.2 1.62 80/67 22.9 17.7 1.17 22.1 18.0 1.27 20.9 17.9 1.39 19.5 17.5 1.50 18.3 17.1 1.62 75/62* 20.7 17.7 1.19 20.0 18.1 1.29 19.0 17.9 1.40 17.9 17.2 1.51 16.9 16.2 1.62 70/57 18.9 17.7 1.20 18.4 17.7 1.29 17.6 16.9 1.40 16.6 15.9 1.50 15.6 1.61 8 Unitary Products Group
Table 4: SYSTEM COOLING CAPACITY - 1 Cylinder 1 (Continued) H4TS048 / G+FD048S21, 24 900 1000 85/72 30.2 20.0 1.39 28.6 19.5 1.55 27.0 18.9 1.70 25.3 18.3 1.84 23.7 17.8 1.97 80/67 27.6 20.0 1.38 26.1 19.4 1.54 24.7 18.9 1.68 23.2 18.3 1.81 21.6 17.7 1.93 75/62 25.1 20.2 1.37 23.8 19.6 1.52 22.4 19.1 1.66 21.0 18.4 1.78 19.5 17.7 1.89 70/57 22.6 20.1 1.36 21.5 19.7 1.51 20.3 19.0 1.63 19.2 18.2 1.75 18.0 17.1 1.86 85/72 30.5 21.1 1.39 28.9 20.6 1.55 27.2 20.0 1.70 25.7 19.5 1.84 23.9 18.9 1.97 80/67 28.0 21.2 1.38 26.5 20.6 1.54 25.0 20.0 1.68 23.4 19.4 1.82 21.9 18.7 1.94 75/62 25.4 21.3 1.37 24.1 20.7 1.52 22.7 20.1 1.66 21.4 19.6 1.79 19.9 18.8 1.90 70/57 23.1 21.3 1.36 21.9 20.6 1.51 20.9 19.8 1.64 19.7 18.6 1.76 18.4 17.5 1.87 85/72 30.7 22.2 1.39 29.3 21.8 1.56 27.6 21.2 1.71 25.9 20.5 1.85 24.1 19.9 1.98 80/67 28.3 22.3 1.38 26.8 21.7 1.54 25.2 21.0 1.69 23.6 20.4 1.82 22.0 19.7 1.94 75/62 25.7 22.4 1.37 24.3 21.7 1.53 23.0 21.2 1.67 21.7 20.6 1.79 20.4 19.3 1.91 70/57 23.6 22.4 1.37 22.5 21.3 1.51 21.3 20.2 1.65 20.0 19.0 1.77 18.7 17.8 1.88 H4TS048 / G+FD060S24 900 1000 85/72 30.3 20.1 1.39 28.7 19.5 1.55 27.0 18.9 1.70 25.5 18.4 1.84 23.8 17.8 1.97 80/67 27.5 20.0 1.38 26.2 19.5 1.54 24.7 18.9 1.68 23.2 18.3 1.81 21.6 17.7 1.93 75/62 25.0 20.2 1.37 23.6 19.5 1.52 22.3 19.0 1.66 20.9 18.3 1.78 19.6 17.7 1.90 70/57 22.5 20.1 1.36 21.4 19.5 1.51 20.2 18.8 1.64 19.1 18.1 1.75 17.9 17.0 1.86 85/72 30.6 21.2 1.39 29.0 20.6 1.55 27.5 20.1 1.71 25.7 19.5 1.84 24.0 18.9 1.97 80/67 28.0 21.2 1.38 26.5 20.6 1.54 25.0 20.0 1.68 23.4 19.4 1.82 21.8 18.7 1.94 75/62 25.3 21.3 1.37 24.0 20.7 1.52 22.6 20.0 1.66 21.3 19.4 1.79 19.8 18.6 1.90 70/57 23.0 21.2 1.36 21.8 20.5 1.51 20.8 19.7 1.64 19.6 18.5 1.76 18.3 17.3 1.87 85/72 30.9 22.3 1.39 29.4 21.8 1.56 27.7 21.2 1.71 25.9 20.5 1.85 24.1 19.9 1.98 80/67 28.3 22.3 1.38 26.8 21.7 1.54 25.2 21.0 1.69 23.6 20.4 1.82 22.1 19.8 1.95 75/62 25.6 22.4 1.37 24.4 21.8 1.53 22.9 21.1 1.67 21.6 20.5 1.79 20.3 19.2 1.91 70/57 23.5 22.3 1.37 22.4 21.2 1.52 21.2 20.1 1.65 19.9 18.9 1.77 18.6 17.6 1.88 H4TS060 / G+FD060S24 1200 85/72 39.7 26.6 1.86 37.7 25.9 2.11 35.6 25.2 2.34 33.5 24.4 2.55 31.4 23.8 2.76 80/67 36.4 26.6 1.87 34.5 25.9 2.09 32.7 25.2 2.31 30.7 24.4 2.51 28.8 23.7 2.69 75/62 33.1 26.9 1.87 31.4 26.2 2.08 29.7 25.4 2.27 27.9 24.6 2.45 26.0 23.8 2.62 70/57 30.0 26.8 1.86 28.4 26.0 2.05 26.9 25.4 2.23 25.3 24.4 2.40 23.9 23.2 2.56 85/72 40.1 27.8 1.86 38.0 27.1 2.11 35.9 26.4 2.34 33.9 25.7 2.56 31.7 24.9 2.77 80/67 36.7 27.8 1.87 34.9 27.2 2.10 33.0 26.4 2.31 31.0 25.6 2.51 29.0 24.8 2.70 75/62 33.5 28.1 1.87 31.8 27.4 2.08 30.0 26.6 2.28 28.1 25.7 2.46 26.4 25.0 2.64 70/57 30.3 28.0 1.86 28.9 27.3 2.06 27.4 26.6 2.24 25.9 25.1 2.41 24.4 23.6 2.58 85/72 40.4 29.0 1.86 38.3 28.3 2.11 36.3 27.7 2.35 34.1 26.9 2.57 31.9 26.1 2.78 80/67 37.1 29.1 1.87 35.2 28.3 2.10 33.3 27.5 2.32 31.2 26.7 2.52 29.1 25.9 2.71 1300 75/62 33.8 29.3 1.87 32.1 28.5 2.08 30.3 27.8 2.28 28.5 27.0 2.47 26.8 26.0 2.65 70/57 30.9 29.3 1.87 29.4 28.5 2.06 27.9 27.1 2.25 26.4 25.6 2.43 24.8 24.0 2.59 H4TS060 / G+FD061H24 1200 CONDENSER ENTERING TEMPERATURE 85/72 39.8 26.6 1.86 37.8 25.9 2.10 35.7 25.2 2.34 33.5 24.4 2.55 31.4 23.8 2.76 80/67 36.4 26.6 1.86 34.5 25.8 2.09 32.6 25.2 2.30 30.7 24.4 2.51 28.7 23.7 2.70 75/62 33.1 26.9 1.87 31.4 26.2 2.07 29.7 25.4 2.27 27.9 24.6 2.45 26.0 23.8 2.62 70/57 30.0 26.8 1.86 28.4 26.1 2.05 26.9 25.3 2.23 25.4 24.6 2.40 23.9 23.1 2.56 85/72 40.1 27.8 1.86 38.1 27.1 2.11 35.9 26.4 2.34 33.9 25.7 2.56 31.7 25.0 2.77 80/67 36.8 27.9 1.86 34.9 27.2 2.10 33.0 26.4 2.31 31.0 25.6 2.51 28.9 24.8 2.71 75/62 33.5 28.1 1.87 31.8 27.4 2.08 30.0 26.6 2.28 28.1 25.8 2.46 26.4 25.0 2.64 70/57 30.4 28.1 1.86 28.9 27.3 2.06 27.5 26.6 2.24 25.9 25.1 2.41 24.4 23.6 2.58 Unitary Products Group 9
Table 4: SYSTEM COOLING CAPACITY - 1 Cylinder 1 (Continued) 1300 CONDENSER ENTERING TEMPERATURE 85/72 40.5 29.1 1.86 38.3 28.3 2.11 36.3 27.7 2.35 34.1 26.9 2.57 31.9 26.1 2.78 80/67 37.2 29.1 1.87 35.2 28.3 2.10 33.3 27.6 2.32 31.2 26.8 2.52 29.1 26.0 2.72 75/62 33.8 29.3 1.87 32.1 28.5 2.08 30.2 27.8 2.28 28.5 27.0 2.47 26.8 26.0 2.65 70/57 30.9 29.3 1.87 29.4 28.5 2.06 28.0 27.1 2.25 26.4 25.5 2.43 24.8 24.0 2.60 1. NOTES : All capacities are net indoor fan heat already deducted. rating is for outdoor unit only. *Indicates T.V.A. requirements at 75 DB/65 WB. Table 5: SYSTEM COOLING CAPACITY - 2 Cylinder 1 H4TS024 / G+FD024S14, 17 750 800 CONDENSER ENTERING TEMPERATURE 85/72 28.2 16.3 1.63 27.6 16.5 1.78 26.7 16.5 1.94 25.4 16.3 2.09 23.8 15.8 2.23 80/67 25.8 16.3 1.61 25.3 16.5 1.75 24.4 16.5 1.89 23.2 16.3 2.03 21.7 15.8 2.16 75/62* 23.4 16.3 1.58 22.9 16.6 1.71 22.1 16.6 1.84 21.0 16.5 1.97 19.7 16.0 2.09 70/57 21.1 16.3 1.56 20.7 16.6 1.68 20.1 16.7 1.80 19.1 16.4 1.92 17.9 15.8 2.03 85/72 28.5 16.7 1.64 27.9 16.9 1.79 26.9 17.1 1.94 25.5 16.9 2.10 23.9 16.4 2.24 80/67 26.0 16.7 1.61 25.5 17.0 1.75 24.6 17.0 1.90 23.3 16.9 2.04 21.8 16.4 2.17 75/62* 23.6 16.7 1.59 23.1 17.1 1.72 22.2 17.2 1.85 21.2 17.0 1.98 19.9 16.5 2.10 70/57 21.3 16.7 1.56 21.2 17.3 1.69 20.4 17.2 1.81 19.2 16.8 1.93 18.2 16.4 2.04 10 Unitary Products Group
Table 5: SYSTEM COOLING CAPACITY - 2 Cylinder 1 (Continued) 85/72 28.6 17.1 1.64 28.0 17.4 1.79 27.0 17.5 1.95 25.6 17.4 2.10 23.9 16.9 2.25 80/67 26.2 17.0 1.62 25.7 17.4 1.76 24.7 17.5 1.90 23.4 17.4 2.04 22.0 17.0 2.17 850 75/62* 23.8 17.2 1.59 23.3 17.6 1.72 22.6 17.9 1.86 21.4 17.5 1.99 20.0 16.9 2.11 70/57 21.5 17.1 1.56 21.4 17.8 1.69 20.5 17.7 1.81 19.4 17.3 1.93 18.4 16.6 2.05 H4TS024 / G+FD030S17 750 800 85/72 29.0 16.6 1.62 28.4 16.8 1.76 27.3 16.8 1.92 25.9 16.6 2.07 24.2 16.0 2.21 80/67 26.5 16.6 1.59 26.0 16.9 1.73 24.9 16.8 1.87 23.7 16.6 2.01 22.1 16.0 2.14 75/62* 24.1 16.8 1.56 23.5 17.0 1.69 22.6 16.9 1.82 21.4 16.7 1.95 20.1 16.1 2.07 70/57 21.8 16.7 1.54 21.3 17.0 1.66 20.6 17.0 1.78 19.4 16.6 1.90 18.2 16.0 2.00 85/72 29.2 17.1 1.62 28.6 17.4 1.77 27.5 17.3 1.92 26.0 17.1 2.07 24.4 16.7 2.21 80/67 26.8 17.1 1.59 26.2 17.4 1.73 25.1 17.3 1.88 23.8 17.1 2.02 22.3 16.6 2.14 75/62* 24.3 17.2 1.57 23.7 17.5 1.70 22.8 17.5 1.83 21.6 17.3 1.96 20.3 16.7 2.08 70/57 22.0 17.2 1.54 21.7 17.7 1.66 20.8 17.6 1.79 19.6 17.1 1.90 18.6 16.7 2.02 85/72 29.4 17.5 1.62 28.8 17.8 1.77 27.6 17.9 1.93 26.2 17.7 2.08 24.4 17.2 2.22 80/67 27.0 17.5 1.60 26.4 17.9 1.74 25.3 17.9 1.88 23.9 17.7 2.02 22.4 17.2 2.15 850 75/62* 24.5 17.7 1.57 23.9 18.0 1.70 23.1 18.2 1.83 21.8 17.8 1.96 20.4 17.2 2.08 70/57 22.1 17.6 1.54 21.9 18.2 1.67 21.0 18.1 1.79 19.8 17.7 1.91 18.8 16.9 2.03 H4TS024 / G+FD036S17 750 800 85/72 29.8 17.1 1.61 29.0 17.3 1.76 27.8 17.1 1.91 26.2 16.7 2.07 24.5 16.2 2.21 80/67 27.2 17.1 1.59 26.5 17.3 1.73 25.4 17.1 1.87 23.9 16.7 2.01 22.4 16.2 2.13 75/62* 24.7 17.2 1.56 24.0 17.4 1.69 23.0 17.3 1.82 21.7 16.9 1.95 20.4 16.4 2.06 70/57 22.3 17.2 1.53 21.7 17.3 1.65 20.9 17.3 1.78 19.7 16.9 1.89 18.4 16.3 2.00 85/72 30.0 17.6 1.62 29.2 17.8 1.77 28.0 17.7 1.92 26.4 17.4 2.07 24.7 16.8 2.21 80/67 27.5 17.6 1.59 26.7 17.8 1.73 25.6 17.7 1.87 24.1 17.3 2.01 22.5 16.8 2.14 75/62* 24.9 17.7 1.56 24.2 17.9 1.70 23.2 17.8 1.82 21.9 17.6 1.95 20.5 17.0 2.07 70/57 22.5 17.7 1.54 22.1 18.1 1.66 21.1 17.8 1.78 19.9 17.5 1.90 18.8 16.9 2.01 85/72 30.2 18.0 1.62 29.4 18.3 1.77 28.1 18.2 1.92 26.5 17.9 2.08 24.8 17.4 2.22 80/67 27.7 18.1 1.59 26.9 18.3 1.74 25.7 18.2 1.88 24.3 18.0 2.02 22.8 17.5 2.15 850 75/62* 25.1 18.2 1.57 24.4 18.5 1.70 23.4 18.5 1.83 22.1 18.1 1.96 20.7 17.5 2.08 70/57 22.7 18.2 1.54 22.4 18.6 1.67 21.3 18.4 1.79 20.3 18.2 1.91 19.1 17.2 2.03 H4TS030 / G+FD030S17 950 1000 85/72 33.8 20.6 1.96 33.4 21.0 2.20 32.4 21.0 2.47 31.0 20.7 2.79 29.5 20.1 3.16 80/67 31.1 20.8 1.92 30.7 21.1 2.15 29.8 21.1 2.41 28.5 20.7 2.72 27.0 20.2 2.08 75/62* 28.5 21.0 1.88 28.1 21.3 2.10 27.3 21.4 2.35 26.1 21.1 2.65 24.7 20.4 3.01 70/57 26.1 21.2 1.85 25.6 21.4 2.06 25.0 21.6 2.31 23.9 21.1 2.60 22.7 20.5 2.95 85/72 34.0 21.1 1.96 33.6 21.4 2.21 32.6 21.5 2.48 31.1 21.1 2.80 29.6 20.7 3.17 80/67 31.3 21.2 1.92 30.9 21.5 2.15 30.0 21.6 2.41 28.6 21.2 2.72 27.2 20.7 3.09 75/62* 28.7 21.5 1.88 28.36 21.8 2.10 27.4 21.8 2.36 26.2 21.6 2.65 24.9 21.1 3.01 70/57 26.2 21.6 1.85 25.8 21.9 2.06 25.2 22.1 2.31 24.1 21.7 2.60 22.9 21.1 2.96 85/72 34.4 21.8 1.97 33.9 22.3 2.21 32.8 22.4 2.48 31.5 22.3 2.80 29.8 21.7 3.18 80/67 31.7 22.0 1.92 31.2 22.4 2.15 30.3 22.6 2.42 28.8 22.2 2.73 27.4 21.8 3.09 75/62* 29.0 22.3 1.88 28.6 22.7 2.10 27.7 22.9 2.36 26.5 22.6 2.66 25.1 22.0 3.02 70/57 26.5 22.4 1.85 26.4 23.2 2.07 25.5 23.0 2.31 24.4 22.6 2.61 23.1 21.9 2.96 H4TS030 / G+FD036S21 950 CONDENSER ENTERING TEMPERATURE 85/72 35.0 21.0 2.00 34.6 21.4 2.24 33.4 21.3 2.52 32.0 21.0 2.84 30.4 20.4 3.22 80/67 32.2 21.1 1.95 31.8 21.5 2.18 30.8 21.5 2.45 29.5 21.1 2.76 27.9 20.5 3.13 75/62* 29.5 21.4 1.91 29.1 21.8 2.13 28.2 21.7 2.39 26.9 21.3 2.69 25.6 20.7 3.06 70/57 27.0 21.5 1.87 26.7 22.0 2.09 25.8 21.8 2.34 24.6 21.4 2.64 23.4 20.8 2.99 Unitary Products Group 11
Table 5: SYSTEM COOLING CAPACITY - 2 Cylinder 1 (Continued) 1000 85/72 35.2 21.4 2.00 34.7 21.9 2.25 33.5 21.7 2.52 32.2 21.6 2.85 30.5 21.0 3.22 80/67 32.4 21.5 1.95 32.0 22.0 2.19 31.0 22.0 2.45 29.6 21.7 2.76 28.1 21.1 3.14 75/62* 29.7 21.8 1.91 29.3 22.3 2.13 28.4 22.3 2.39 27.1 21.9 2.70 25.8 21.4 3.06 70/57 27.1 21.9 1.87 26.9 22.5 2.09 26.0 22.4 2.34 24.8 21.9 2.64 23.6 21.4 2.99 85/72 35.5 22.2 2.01 35.1 22.8 2.25 33.9 22.9 2.53 32.5 22.7 2.85 30.8 22.2 3.32 80/67 32.8 22.4 1.96 32.3 22.9 2.19 31.2 22.9 2.46 29.8 22.7 2.77 28.4 22.2 3.14 75/62* 30.0 22.7 1.91 29.7 23.3 2.14 28.8 23.4 2.40 27.4 23.0 2.70 26.0 22.5 3.06 70/57 27.7 23.0 1.88 27.3 23.4 2.10 26.3 23.4 2.35 25.2 23.1 2.64 23.9 22.4 3.00 H4TS030 / G+FD042S21 950 1000 85/72 35.9 22.6 2.00 35.4 22.9 2.25 34.1 22.6 2.52 32.7 22.5 2.84 31.1 21.9 3.22 80/67 33.1 22.7 1.95 32.6 23.0 2.19 31.4 22.8 2.45 30.0 22.5 2.76 28.4 21.8 3.13 75/62* 30.3 23.0 1.91 29.8 23.3 2.13 28.7 23.1 2.39 27.4 22.7 2.69 26.1 22.2 2.99 70/57 27.6 23.1 1.87 27.3 23.5 2.09 26.4 23.3 2.34 25.1 22.9 2.63 23.8 22.3 2.99 85/72 36.1 23.0 2.01 35.6 23.4 2.25 34.3 23.2 2.53 32.9 23.1 2.85 31.1 22.4 3.22 80/67 33.3 23.2 1.96 32.8 23.5 2.19 31.6 23.4 2.46 30.2 23.1 2.76 28.7 22.5 3.13 75/62* 30.5 23.5 1.91 30.0 23.8 2.14 28.9 23.8 2.39 27.6 23.4 2.69 26.2 22.7 3.06 70/57 27.8 23.6 1.87 27.5 24.1 2.09 26.5 23.9 2.34 25.3 23.5 2.64 23.9 22.8 2.99 85/72 36.5 23.9 2.01 35.9 23.4 2.26 34.7 23.2 2.53 33.1 24.2 2.85 31.4 23.6 3.23 80/67 33.6 24.0 1.96 33.1 24.5 2.19 31.9 24.6 2.46 30.4 24.3 2.77 29.0 23.7 3.14 75/62* 30.8 24.4 1.91 30.3 24.9 2.14 29.3 25.0 2.40 27.9 24.5 2.70 26.5 23.9 3.06 70/57 28.3 24.6 1.88 27.9 25.1 2.10 26.9 25.0 2.34 25.6 24.6 2.64 24.3 23.9 3.00 H4TS036 / G+FD036S21 1200 85/72 40.3 24.7 2.31 39.4 24.9 2.52 37.9 24.9 2.73 35.9 24.4 2.95 33.8 23.8 3.16 80/67 36.9 24.6 2.28 36.1 25.0 2.48 34.7 24.9 2.68 32.8 24.4 2.89 30.8 23.7 3.08 75/62* 33.7 24.9 2.25 32.9 25.2 2.43 31.6 25.2 2.62 29.9 24.6 2.82 28.0 23.8 3.00 70/57 30.6 24.9 2.21 30.1 25.3 2.39 28.8 25.2 2.57 27.1 24.6 2.75 25.5 23.8 2.91 85/72 40.7 25.6 2.31 39.7 25.9 2.52 38.2 26.0 2.74 36.2 25.6 2.96 34.0 24.9 3.17 80/67 37.3 25.5 2.28 36.5 25.9 2.48 35.0 26.0 2.69 33.1 25.6 2.89 31.1 24.8 3.09 75/62* 34.0 25.8 2.25 33.4 26.4 2.44 32.0 26.3 2.63 30.2 25.7 2.83 28.3 24.9 3.01 70/57 31.3 26.1 2.22 30.4 26.3 2.40 29.1 26.2 2.58 27.5 25.7 2.76 26.0 24.8 2.94 85/72 40.9 26.3 2.31 40.0 26.8 2.53 38.5 27.0 2.74 36.4 26.7 2.97 34.2 25.9 3.18 80/67 37.6 26.3 2.29 36.7 26.9 2.49 35.4 27.1 2.70 33.4 26.7 290 31.3 25.8 3.10 1300 75/62* 34.3 26.6 2.26 33.7 27.3 2.45 32.3 27.3 2.64 30.4 26.8 2.84 28.6 26.1 3.02 70/57 31.6 26.9 2.23 30.8 27.3 2.40 29.5 27.3 2.59 28.0 26.8 2.78 26.4 25.2 2.96 H4TS036 / G+FD042S21 1200 CONDENSER ENTERING TEMPERATURE 85/72 40.5 24.8 2.31 39.5 25.1 2.51 38.0 25.0 2.73 35.9 24.5 2.95 33.8 23.8 3.15 80/67 37.1 24.9 2.28 36.2 25.1 2.48 34.7 24.9 2.68 32.8 24.5 2.88 30.8 23.7 3.08 75/62* 33.9 25.1 2.25 33.0 25.4 2.43 31.6 25.3 2.62 29.8 24.6 2.81 27.9 23.8 2.99 70/57 30.8 25.2 2.21 30.1 25.5 2.39 28.8 25.3 2.56 27.0 24.6 2.74 25.4 23.8 2.91 85/72 40.9 25.7 2.31 39.9 26.1 2.52 38.2 26.0 2.74 36.2 25.7 2.95 33.9 24.8 3.17 80/67 37.5 25.8 2.28 36.6 26.1 2.48 35.0 26.0 2.69 33.1 25.6 2.89 31.1 24.8 3.09 75/62* 34.2 26.0 2.25 33.3 26.4 2.44 32.0 26.4 2.63 30.1 25.7 2.82 28.2 24.9 3.01 70/57 31.4 26.4 2.22 30.5 26.5 2.39 29.1 26.3 2.57 27.5 25.7 2.75 25.9 24.9 2.93 85/72 41.2 26.5 2.31 40.2 27.0 2.52 38.5 27.0 2.74 36.3 26.6 2.96 34.2 26.0 3.17 80/67 37.8 26.6 2.29 36.9 27.1 2.49 35.2 27.0 2.69 33.3 26.6 2.90 31.3 25.8 3.10 1300 75/62* 34.5 26.9 2.26 33.8 27.5 2.45 32.3 27.4 2.64 30.4 26.8 2.83 28.5 26.1 3.02 70/57 31.7 27.2 2.22 30.8 27.5 2.40 29.5 27.4 2.59 28.0 26.9 2.77 26.4 25.3 2.95 H4TS036 / G+FD048S21, 24 12 Unitary Products Group
Table 5: SYSTEM COOLING CAPACITY - 2 Cylinder 1 (Continued) 1200 85/72 42.2 25.8 2.33 40.9 25.9 2.54 39.0 25.5 2.76 36.8 24.9 2.98 34.5 24.1 3.19 80/67 38.7 25.9 2.30 37.5 25.9 2.51 35.7 25.5 2.71 33.6 24.9 2.91 31.5 24.1 3.12 75/62* 35.2 26.1 2.27 34.1 26.1 2.46 32.4 25.7 2.66 30.5 25.1 2.84 28.6 24.2 3.03 70/57 32.0 26.1 2.24 31.1 26.3 2.41 29.4 25.7 2.60 27.7 25.1 2.77 25.9 24.2 2.94 85/72 42.6 26.8 2.33 41.3 26.9 2.55 39.3 26.6 2.77 37.0 26.0 2.99 34.7 25.3 3.20 80/67 39.1 26.9 2.31 37.9 27.0 2.51 36.0 26.6 2.72 33.9 26.0 2.93 31.9 25.4 3.13 75/62* 35.7 27.1 2.28 34.6 27.4 2.47 32.8 26.9 2.67 30.8 26.2 2.86 28.9 25.5 3.04 70/57 32.6 27.4 2.25 31.5 27.3 2.43 29.8 26.8 2.61 28.1 26.2 2.79 26.6 25.4 2.97 85/72 43.0 27.7 2.34 41.7 28.0 2.55 39.7 27.9 2.77 37.3 27.2 3.00 35.1 26.6 3.21 80/67 39.5 27.8 2.31 38.2 28.0 2.52 36.4 27.9 2.73 34.2 27.2 2.94 32.0 26.4 3.14 1300 75/62* 36.0 28.1 2.28 35.0 28.4 2.48 33.2 28.1 2.67 31.2 27.5 2.87 29.2 26.6 3.06 70/57 33.0 28.3 2.25 31.9 28.4 2.43 30.3 28.1 2.62 28.8 27.4 2.81 27.1 25.8 2.99 H4TS048 / G+FD048S21, 24 1450 1600 1750 CONDENSER ENTERING TEMPERATURE 85/72 58.3 36.5 3.76 55.7 35.5 4.03 53.0 34.5 4.33 50.1 33.4 4.62 47.2 32.3 4.92 80/67 53.5 36.6 3.67 51.0 35.6 3.09 48.5 34.5 4.19 45.8 33.4 4.47 43.1 32.2 4.73 75/62* 48.6 36.9 3.57 46.4 35.9 3.80 44.0 34.8 4.05 41.5 33.6 4.50 39.2 32.8 4.55 70/57 44.2 37.0 3.47 42.3 36.2 3.69 40.1 35.0 3.92 37.8 33.7 4.15 35.5 32.5 4.37 85/72 59.0 38.0 3.78 56.3 37.0 4.06 53.5 36.0 4.35 50.6 34.9 4.65 47.6 33.8 4.95 80/67 54.1 38.1 3.69 51.6 37.1 3.95 49.0 36.0 4.22 46.3 34.9 4.50 43.5 33.7 4.76 75/62* 49.3 38.5 3.60 46.9 37.4 3.83 44.5 36.3 4.08 42.3 35.5 4.34 39.7 34.2 4.59 70/57 45.1 38.9 3.50 42.9 37.7 3.72 40.7 36.5 3.95 38.4 35.2 4.18 36.2 34.4 4.42 85/72 59.6 39.5 3.80 56.8 38.5 4.08 54.0 37.4 4.37 51.0 36.3 4.68 48.0 35.2 4.97 80/67 54.7 39.6 3.71 52.1 38.5 3.97 49.4 37.4 4.24 46.6 36.3 4.52 43.8 35.1 4.79 75/62* 49.8 40.0 3.61 47.4 38.9 3.85 45.3 38.1 4.11 42.7 36.9 4.37 40.1 35.6 4.62 70/57 45.7 40.3 3.52 43.5 39.1 3.74 41.2 37.9 3.98 39.1 37.1 4.22 36.7 35.5 4.45 Unitary Products Group 13
Table 5: SYSTEM COOLING CAPACITY - 2 Cylinder 1 (Continued) H4TS048 / G+FD060S24 1450 1600 85/72 59.6 38.1 3.72 56.8 37.0 3.99 54.0 35.9 4.28 51.0 34.7 4.58 48.0 33.5 4.87 80/67 54.7 38.2 3.63 52.1 37.1 3.88 49.4 35.9 4.15 46.7 34.7 4.43 43.8 33.4 4.69 75/62* 49.8 38.6 3.54 47.4 37.4 3.77 44.9 36.2 4.01 42.3 34.9 4.26 39.9 33.9 4.52 70/57 45.2 38.6 3.44 43.3 37.7 3.66 41.0 36.4 3.88 38.6 35.1 4.12 36.1 33.7 4.33 85/72 60.3 39.7 3.74 57.5 38.6 4.01 54.6 37.5 4.31 51.5 36.3 4.61 48.5 35.1 4.90 80/67 55.4 39.9 3.65 52.7 38.7 3.91 50.0 37.5 4.18 47.2 36.3 4.46 44.3 35.0 4.72 75/62* 50.5 40.3 3.56 48.0 39.1 3.79 45.4 37.8 4.04 43.1 36.9 4.30 40.5 35.5 4.55 70/57 46.2 40.6 3.47 44.0 39.3 3.66 41.6 38.0 3.91 39.1 36.6 4.15 36.6 35.2 4.37 85/72 60.9 41.3 3.75 58.0 40.2 4.03 55.0 39.0 4.33 52.0 37.8 4.63 48.8 36.6 4.93 80/67 56.0 41.4 3.67 53.3 40.3 3.92 50.5 39.0 4.20 47.6 37.8 4.48 44.9 36.8 4.76 1750 75/62* 51.0 41.9 3.57 48.5 40.7 3.81 46.3 39.7 4.07 43.6 38.3 4.33 40.9 36.9 4.58 70/57 46.8 41.9 3.49 44.5 40.6 3.70 42.1 39.3 3.94 39.6 37.9 4.17 37.4 36.6 4.42 H4TS060 / G+FD060S24 1 1900 85/72 69.9 42.9 4.54 66.8 41.8 4.91 63.5 40.7 5.29 60.2 39.5 5.67 56.7 38.3 6.03 80/67 64.2 43.1 4.37 61.3 41.9 4.71 58.3 40.7 5.05 55.1 39.5 5.40 51.8 38.2 5.73 75/62* 58.5 43.5 4.20 55.8 42.3 4.51 53.0 41.1 4.82 51.3 40.1 5.15 47.3 38.7 5.45 70/57 53.5 43.9 4.05 51.0 42.6 4.33 48.4 41.3 4.62 45.7 39.9 4.91 42.9 38.5 5.19 85/72 70.8 45.1 4.58 67.7 44.1 4.95 64.3 42.9 5.33 60.9 41.8 5.70 57.3 40.6 6.07 80/67 65.1 45.4 4.40 62.1 44.2 4.74 59.0 43.0 5.09 55.8 41.8 5.44 52.6 40.7 5.80 75/62* 59.4 45.9 4.23 56.6 44.6 4.54 53.9 43.5 4.88 51.0 42.2 5.20 47.9 40.8 5.51 70/57 54.4 46.1 4.08 51.8 44.8 4.37 49.1 43.4 4.67 46.4 42.1 4.96 43.9 40.9 5.25 85/72 71.2 46.2 4.59 68.0 45.1 4.97 64.6 44.0 5.35 61.1 42.8 5.72 57.5 41.6 6.09 80/67 65.5 46.4 4.41 62.4 45.3 4.76 59.3 44.1 5.11 56.2 43.0 5.49 52.9 41.7 5.82 2000 75/62* 59.8 47.0 4.24 57.1 45.9 4.57 54.3 44.6 4.90 51.3 43.2 5.22 48.2 41.8 5.54 70/57 54.8 47.1 4.10 52.2 45.8 4.39 49.5 44.4 4.69 47.0 43.5 4.99 44.8 42.5 5.33 H4TS060 / G+FD061H24 1 1900 2000 CONDENSER ENTERING TEMPERATURE 85/72 70.7 44.1 4.57 67.5 43.0 4.95 64.3 41.8 5.33 60.9 40.6 5.70 57.2 39.3 6.08 80/67 64.9 44.3 4.40 62.0 43.1 4.74 58.9 41.9 5.09 55.7 40.7 5.43 52.3 39.2 5.78 75/62* 59.1 44.8 4.22 56.4 43.5 4.53 53.5 42.3 4.85 50.7 41.0 5.19 47.6 39.6 5.50 70/57 53.9 44.9 4.07 51.4 43.6 4.36 48.8 42.3 4.66 46.0 40.9 4.95 43.2 39.5 5.23 85/72 71.5 46.3 4.62 68.3 45.1 5.00 64.9 43.9 5.38 61.4 42.7 5.76 57.9 41.7 6.12 80/67 65.7 46.4 4.44 62.7 45.2 4.78 59.5 44.0 5.14 56.2 42.7 5.49 53.1 41.9 5.84 75/62* 59.9 46.9 4.26 57.1 45.7 4.58 54.5 44.8 4.91 51.5 43.4 5.23 48.4 42.0 5.54 70/57 54.9 47.3 4.11 52.3 46.0 4.40 49.6 44.7 4.70 47.0 43.5 5.02 44.2 41.9 5.30 85/72 71.9 47.4 4.63 68.6 46.2 5.02 65.2 45.0 5.40 61.8 44.0 5.78 58.0 42.6 6.16 80/67 66.1 47.5 4.45 63.0 46.3 4.80 59.8 45.1 5.16 56.7 44.1 5.53 53.4 42.9 5.86 75/62* 60.3 48.1 4.28 57.7 47.2 4.60 54.8 45.9 4.93 51.8 44.5 5.26 48.6 43.1 5.57 70/57 55.3 48.5 4.12 52.7 47.1 4.42 49.9 45.8 4.72 47.4 44.5 5.03 45.2 43.6 5.38 1. NOTES : All capacities are net indoor fan heat already deducted. rating is for outdoor unit only. *Indicates T.V.A. requirements at 75 DB/65 WB. 14 Unitary Products Group
Table 6: PHYSICAL AND ELECTRICAL DATA MODEL H4TS024 H4TS030 H4TS036 H4TS048 H4TS060 UNIT SUPPLY VOLTAGE 208/230-1-60 NORMAL VOLTAGE RANGE 1 187 to 252 MIN. CIRCUIT AMPACITY 13.4 15.3 18.6 32.8 35.3 MAX. OVERCURRENT DEVICE AMPS 2 20 25 30 50 60 COMPRESSOR TYPE BRISTOL TS COMPRESSOR AMPS RATED LOAD 10.3 11.7 25.7 27.0 LOCKED ROTOR 64 65 84 135 147 CRANKCASE HEATER YES YES YES YES YES FAN MOTOR AMPS RATED LOAD.5.5.7.7 1.5 FAN DIAMETER INCHES 18 18 24 24 24 RATED HP 1/12 1/12 1/10 1/10 1/4 FAN MOTOR NOMINAL RPM 825 825 850 NOMINAL 1850 1850 2800 2800 3200 FACE AREA SQ. FT 14.2 14.2 20.0 24.0 24.0 COIL COIL ROWS DEEP 1 1 1 1 1 FIN / INCH 20 20 20 20 20 LIQUID LINE OD 3/8 3/8 3/8 3/8 3/8 VAPOR LINE OD 3/4 3/4 7/8 7/8 7/8 UNIT CHARGE, (LBS - OZ) 3 5-9 6-9 7-0 9-12 9-2 CHARGE PER FOOT, OZ.68.68.70.7.7 OPERATING WEIGHT LBS. 145 145 200 250 252 1 Rated in accordance with ARI Standard 110. utilization range A. 2 Dual element fuses or HACR circuit breaker. 3 The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant calculated, using the difference in length multiplied by the per foot value. UNIT MODEL HTS REFRIGERANT DIMENSIONS CONNECTION LINE SIZE A B C LIQUID VAPOR 024 30-1/8 24 24 030 30-1/8 24 24 3/4 48" OVERHEAD CLEARANCE C 036 31-7/8 35 35 3/8 B 048 37-7/8 35 35 7/8 060 37-7/8 35 35 ACCESSORIES (Refer to Price Manual for specific model numbers.) Dehumidification Control - Model 2HU06124 available for use in areas where a higher level of humidity control is required. Room Thermostat - Matching 2-Stage cooling thermostats are available to provide features required for any installation. See list below: 2ET03024 2ET03124 2ET03224 2ET03324 A IN 4 SIDES TXV Kit - Factory specified and required for proper unit performance. H4TS024 = 1TV0701 H4TS030 = 1TV0701 H4TS036 = 1TV0702 H4TS048 = 1TV0704 (w/ 4 ton evap coils) 1TV0703 (w/ 5 ton evap coils) H4TS060 = 1TV0703 VAPOR CONNECTION 2-3/8 5-1/2 LIQUID CONNECTION 3-1/8 Unitary Products Group 15
MATCHING COMPONENTS Add-On Coils - For Furnace Application Air Handlers - For Non-Furnace Application G-UA COIL G-HD COIL N-AH BLOWER/ G+FD COIL UPFLOW DOWNFLOW HORIZONTAL G+FD COIL F2RC / F2FC OR F2RP / F2FP FAN COIL UNITS UPFLOW HORIZONTAL +HDWLQJDQG$LU&RQGLWLRQLQJ Unitary Products Group 5005 York Drive, Norman, Oklahoma 73069 Subject to change without notice. Printed in U.S.A. 036-21023-003 Rev. A (0500) Copyright by Unitary Products Group 2000. All rights reserved. Supersedes: 550.37-TG4Y (0200) & 036-21023-002A (0200)