PARTS LIST AND INSTRUCTIONS WHEELHORSE PRODUCTS, INC. SOUTH BEND, IND. SAfETY FIRST Avoid acci dents by keeping hands and feet clear of blade while starting engine and while engine is running. CONTROL LEVER IN OFF POSITION Shut off engine and remove spark plug "'" wi re before adding gas ar oi I and before making adjustments or inspection of any kind. ROTARY MOWER Self Propelled INSTRUCTIONS LC MODELS STARTING WARNING! BE SURE HANDS AND FEET ARE CLEAR OF THE MOWER BASE BEFORE ATTEMPTING TO START THE ENGINE ASSEM8LING HANDLE Assemble lower handle to deck by inserting pins, in handle, thru holes in brackets. The pins in the brackets likewise will assemble in holes in handle. Then Secure the handle with spring pins provided. Assemble upper handle, Control Panel and lower handle with nuts and bolts provided. See illustration at right OIL AND GASOLINE Push throttle lever to choke position and place clutch lever in neutral position (center notch). For Impulse Starter: Standing on left side of mower, push In on release lever, unfold the starter handle and wind up clockwise about 3Y turns Fold handle over and pull out on the release lever. For Recoil Starter: Standing at the rear of the mower, grasp the starter handle firmly in your hand and give it a quick pull to complete cord length. Return the Starter handle slowly. When engine starts, pull the throttle lever back approximately halfway or until engine runs about /3 open throttle. THROTTLE LEVER \ NEVER FILL THE GAS TANK WHILE THE ENGINE IS RUNNING DO NOT MIX OIL WITH GASOLINE Remove oil filler plug and fill with SAE. 30 motor oil up to the top of the filler hole. Be sure engine is level when adding oil to avoid over filling. Fill the gas tank with clean, fresh, regular gasoline. Premium Grade Ethyl is not recommended. If engine fails to start after 3 repeated attempts, turn the low speed screw and high speed. screw clockwi se unti I finger tight. Turn high speed screw counter-clockwise about one full turn and low speed screw counter-clockwise about one and one hal f turns. Repeat starting operation. 4 The first time the engine is started, allow to run at /3 open throttle for 0 to 5 minutes to thoroughry lubricate all moving parts and bearings - 3 -
TO MOW WARNING! BE SURE LAWN IS CLEAR OF BONES, WIRE, STICKS, STONES OR OTHER OBJECTS WHICH COULD DAMAGE THE CUT TING BLADES Li ft up on clutch control lever and place in Hi or Low position" Take special care when straddling humps or ridges with your mower" TO STOP ENGINE Use the left side (the side opposite the chute opening) of your mower when trimming close to buildings, fences, etc. Stop mower by placing clutch lever in neutral position" Stop Engine by pulling throttle lever back to stop position" ROUTINE MAINTENANCE AND ADJUSTMENT 'f9 c6 ELEMENT FRONT HOUSING ~ fa SCREEN.r~ ~ AIR CLEANER COVER Polyurethane Type-Serviceable. Clean element every ten (0) hours or oftener if engine runs rich and emus black smoke from the exhaust. Service by removing air cleaner cover. Remove polyurethane element and wash in detergent and water solution by squeezing similar to a sponge. Squeeze out cleaning solution. Re-oil element by applying generous quantity of oil to sides and open ends. Squeeze to distribute oil and to remove excess oil. Reinstall element and air cleaner cover. OUT 'l(~ @ STORING WARNING! DO NOT ATTEMPT TO MAKE ANY ADJUSTMENTS OR CLEAN GRASS FROM THE MOW ER BASE UNTIL ENGINE IS STOPPED, AND SPARK PLUG WIRE IS REMOVED. 3 The height of cut can be changed by '<'i;;;;;> d( ~'~ rai sing or lowering the axles. ~.,~ REAR AXLE: Pull out on spring adjustment \ ~ lever and move forward to rai se axle and ;,,, backward to lower axle., FRONT AXLE: Pull out on spring adjustment lever and move forward to lower axles land backward to raise axle. Raising the a~les will give a lower height of cut and lowering the axles will give a higher height of cut Be sure that all four adjustments be placed in the same posi ti on to keep the mower level 4 Adlustmentsfortig.ht- ~ enlng or loosening /t dri ve chai n are made ( by turning adjusting ~ ~~,ok. 00 OhOW"~. ' -, \.~ When it is necessary to store your mower for a period of 30 days or more: Drain gas tank by removing fuel line at the carburetor or fuel tank, lli.rr-f carburetor has float bowl, drain by pushing unward on bowl drain, Remove the spark plug and pour approximately one ounce of engine oil into cylinder. Crank engine slowly about revolutions to spread the oi lover internal surfaces of the engine and then replace the spark plug" A little chassis grease on the'cutting edges of the blade will prevent them from rusting during prolonged storage" Store your mower in a clean dry place, and cover it with canvas or paper to keep off excess dust and dirt, FUEL LINE Drain and refill the crankcase after the first 5 hours of operating Thereafter, dra in and refi II after every 5 hours of operating, Refill crankcase with SAE No, 30 Motor Oil, Fill to top of threads in filler hole, Check oil level of the crank case before each use, (with mower on level ground)" BE SURE DRAIN PLUG IS TIGHT. ADD ONE OUNCE ENGINE OIL TO CYLINDER - 4 -
REO FOUR CYCLE POWER MOWER MODELS 4-LCP 0 06 07 56 66 58 -!=~ 70 80 95 9 97 97 9 98 99 00 SEE PARTS LIST ON REVERSE SIDE - 7 -
REO FOUR CYCLE POWER MOWER MODELS 4.-LCP PARTS LIST When ordering parts always list Part and name of part. Ref. Part Description Ref. Part Description Ref. Part Description 00 3 4 5 6 7 8 9 0 thru 33 thru 4 use 3 4 5 6 7 8 9 0 and use 3 and 4 3 use 4 5 6 7 and 8 7 use 8 9 30 3 thru 33 3 3 33 34 35 S 5 3 MW 8664 MW 8503 MW-8555 MW-8653 MW8679 GM-766 MW-4846 5378 GM-033 GM-784 MW-876 MW-877 MW-877 MW-58 MW-633 MW 437 MW-870 MW-87 MW-464 MW-87 MW-69 MW-589 MW-589 MW-5308 MW-583 MW-583 MW-5306 MW-543 MW-873 MW-577 MW-577 MW-633 MW-6709 GM-97 MW-874 MW-8649 MW-8740 MW6707 MW-43 GM 039 Spring Pin Upper Handle Grip Lower Handle Plate Throttle and Clutch Control Nut and Lockwasher Clip Clip Nut and Lockwasher Transmission Assembly Plate Assembly Plate Tie Shaft Shaft and Assy. Key Collar Yoke Assembly Hub and Assy. Assembly Hub and Assy. Plate Assembly Plate Rod Cotter Pin Control Assembly Bell Crank Pivot Roll Pin 36 37 38 39 40 4 4 43 44 45 46 47 48 49 50 5 5 53 54 55 56 57 58 59 60 thru 7 60,6,6 60 use 6 6 63 64 65 66 67 68 69 70 7 7 73 74 MW-867 MW-487 MW-404 GM-66 GM 7380 MW-8705 GM-94536 MW-879 MW-876 MW-877 MW-878 GM-0376 GM-97 MW-867 GM-74865 MW-466 MW-86 MW-860 MW-853 MW-8590 MW859 GM-007 MW-8659 MW-494 MW-869 MW-869 MW-869 MW-8696 MW-539 MW-8698 MW-60 MW-439 GM-94536 MW-8705 MW-8706 MW-8707 MW-4560 MW433 MW-8708 MW-8709 MW-404 Cable Clamp Screw Nut and Lockwasher Spring Pin Yoke Link R.H. Thread Link L.H. Thread Nut Cotter Pin Guard Nut Decal (Caution) Decal (Power Trim) Base Screw and Lockwasher Drive Assembly Assembly Retainer Assembly Spring Pin Countershaft Retaining Ring Spacer and Lockwasher 75 76 77 78 79 80 8 8 83 84 85 86 87 88 89 90 9 9 93 94 95 96 97 98 99 00 0 0 03 04 05 06 07 08 09 4 5 6 7 MW 8596 MW-8597 MW 8594 MW-8595 MW-8573 MW-8657 MW-8660 GM-74865 MW-403 GM-4356 MW-87 GM-06749 MW-870 MW-4560 MW-87 MW-439 MW-873 MW-874 GM- GM-0394 MW-435 MW-543 MW875 GM-8639 MW-4335 536 MW-776 GM-4546 MW-8579 MW-4754 MW-559 MW-858 MW-8588 GM-450986 MW-875 MW-8756 MW-8638 MW-4345 MW-5830 MW-583 MW-583 Arm Left Front Arm Right Front Arm Left Rear Arm Right Rear Lever Grip Spacer and Lockwasher Axle (Drive) Key Retaining Ring Wheel and Tire Assy. (Front) Wheel and Tire Assy. (Rear) Cotter Pin Wasryer Hub Cap Blade Blade Drive Key Engine Less Starter Collar Starter Assembly Shroud Screw and Lockwasher Chute Cover Assembly Wing Nut Axle (Rear) Spacer Connecting Link Roller Link Offset Link