Kitchen exhaust fan GLEB

Kitchen exhaust fan GLEB

Contents General description...3 Quick selection...5 Design description...5 Material and design...6 Fan impeller...6 Motor...6...6 Quality...6 Specification...6 Technical data Fan charts, sound data, motor data GLEB-1/6-025...14 GLEB-1/6-031...15 GLEB-1/6-040...16 GLEB-1/6-050...17 Fan chart-explanation and definitions...7 Dimensions...9 Wiring diagram...10 Accessories...11 Ordering code...13 Fläkt Woods Oy XXXX GB 2013.01 2 Specifications are subject to alteration without notice

General description Applications Box fans are used in comfort systems, where low energy consumption and low noise levels are required and also in installations where the air is slightly greasy or air temperature is up to 120 C degrees. Two versions for different applications are available: HT-fan F400(120) in accordance with the standard 12101-3 and continuous temperature range up to 120 C degrees. Unit can be installed under the roof and also outside (special protection devices to be used for motor, drive to be installed inside). Easy access for service and cleaning The fan should be regularly cleaned to maintain perfect operation of the fan. Casing is equipped with two inspection hatches, which allow easy access to the impeller and inside casing for cleaning and service. Motor itself is located outside of the casing. Demand control ventilation The demand for different air flows at different times of the day and during different seasons is increasing all the time. Also new ErP Directive is looking for decreased energy consumption of fans. Box fan GLEB is equipped with high efficiency CentriflowPlus impeller. Motor speed can be controlled with frequency converter also in case of HT-version. These allow always best and optimised energy consumption. Quiet operation Box fans are often located near people and low sound levels are important. Impeller itself is quiet and demand controlled fan speed always allows the lowest sound levels. Casing is insulated against sound and condensation. The fan is equipped with installation beams and vibration dampers as standard. Air flow measurement Box fan can be equipped also with air flow measurment device to adjust the correct speed of the motor. Constant pressure systems In case where the constant pressure of the system is requiered, the pressure controller is available as an accessory. Fläkt Woods Oy XXXX GB 2013.01 3 Specifications are subject to alteration without notice

General description Easy installation Both outlet and inlet are equipped with standard Veloduct connection components. The box has also as standard mounting bars fitted with vibration dampers. Flexible connection is recommended to be used both at outlet and inlet. Fläkt Woods Oy XXXX GB 2013.01 4 Specifications are subject to alteration without notice

Quick selection 1200 1000 Pressure Pa 800 600 400 200 0 0,2 0,6 1 1,4 1,4 2,2 2,6 3 Air flow m 3 /s 025 031 040 050 Design description Kitchen exhaust fan is a series of box-fans. The units are available in 4 sizes for air flows up to 2,7 m 3 /s. 8 13 12 6 11 10 1 2 7 4 3 5 9 1. Motor 2. Inlet connection 3. Standing skid 4. Impeller 5. Vibration damper 6. Liftig lug 7. Inlet cone 5 8. Outlet connection 9. Cleaning hatch 10. Front plate 11. Backk plate 12. (optional) 13. Mounting bracket for FC (optional) Fläkt Woods Oy XXXX GB 2013.01 5 Specifications are subject to alteration without notice

Design description Material and design The fan casing is made of galvanised sheet steel. It is equipped with 2 inspection hatches, one on both sides. Outlet and inlet connections are standard Veloduct components having rubber gasket as standard. The unit has as standard mounting bars and dampers. Fan impeller The fan impeller is made of sheet steel, welded and painted with 60 μm thick epoxy paint, ( colour RAL 6029 green). The impeller is dynamically balanced to ISO 1940-1973 G 6.3 ( size 025) and G 2.5 (sizes 031-050) at maximum speed. The vibration level of the fan is below 7.1 mm/s RMS. Motor As standard, box fan is supplied with the motor. The motor is a standard IE2-class 3-phase foot motor outside air stream. As standard motors have thermistors. Quality Our serial production products meet the requirements of DIN 24 166 tolerance class 1. The company has acquired the ISO 9001 quality certificate and the ISO 14001 environment certificate. Specification text A high efficiency box fan equipped with an impeller with optimized blade profile and rotating diffuser. The fan casing is insulated against noise and condensation. The fan is equipped with IE2 standard motor, which can be controlled with frequency converter. HT-version is tested in accordance with ISO 12101-3 standard for class F400(120). The capacity measurement have been performed according to ISO 5801:2007 and the sound power level according to ISO 3741:1999. Requirements have been stated according to the DIN 24 166 class 1. Motors can be controlled with frequency converter. Two different types of VSD are available. 1-phase IP21 class VSD and 3-phase IP 54 class VSD. Fläkt Woods Oy XXXX GB 2013.01 6 Specifications are subject to alteration without notice

Fan chart-explanation and definitions 3 4 2 5 1 1. qv Air flow m 3 /s, m 3 /h 2. Δ pt Total pressure Pa 3. η Fan effieciency ( impeller, motor,drive, if used) % 4. L wa A-weighted total soundlevel to outlet duct db(a) 5. SFF Specific Fan Power J/m 3 L woct Sound power level by octave band (without A-weighting) K oct ΔL Kc Correction, when divided into different octave bands Remote attenuation (given values are calculated for an ideal case in halfspace) Correction used to calculate total sound level for surrounding db db db db Fan code Correction Koct (db) K c (db) GLEB-1/6-025-3-037-0 Octave band mid-frequency (Hz) Sound path Speed r/min 63 Hz 125 Hz 250 Hz 500 Hz 1000 Hz 2000 Hz 4000 Hz 8000 Hz Outlet duct 0-1533 23 6 1-5 -12-15 -24-32 Outlet duct 1534-2900 11 4 6-3 -10-12 -20-28 Inlet duct 0-1533 12 8 0-5 -12-13 -16-18 Inlet duct 1534-2900 10 3 0-5 -11-13 -19-20 Surroundings 0-1533 -14-15 -15-20 -20-17 -16-23 -11 Surroundings 1534-2900 -14-20 -13-22 -18-24 -25-28 -15 Fläkt Woods Oy XXXX GB 2013.01 7 Specifications are subject to alteration without notice

Fan chart-explanation and definitions The total A-weighted sound power level L wa to the outlet duct can be read in the fan chart. The correction coefficients by octave bands can be read in the sound data table. The sound level by octave band to the outlet duct, inlet duct or surroundings (without A-weighting) can be obtained by using following formula, where K oct is read from the correct sound path. L Woct = L wa + K oct Total sound pressure level L pa in the surroundings at certain distance can be obtained by using following formula. L pa = L WA + K c - ΔL Distance L (m) 1 3 5 10 15 20 25 30 35 Attenuation ΔL (db) 7 17 22 28 31 34 36 37 40 Example: GLEB-6-025-3-037-0 fan with 0.2 m 3 /s at 400 Pa From fan chart we get for L wa at fan outlet ~72.5 db(a). Sound data at fan inlet can be calculated as follows: Correction Koct (db) Octave band mid-frequency (Hz) L wa 72,5 72,5 72,5 72,5 72,5 72,5 72,5 72,5 K oct 10 3 0-5 -11-13 -19-20 L woct 82,5 75,5 72,5 67,5 61,5 59,5 53,5 52,5 Sound pressure level at distance of 3 meters is calculated as follows: L WA 72,5 K c -17 ΔL -17 L pa 38,5 DB(A) Fläkt Woods Oy XXXX GB 2013.01 8 Specifications are subject to alteration without notice

Dimensions Ø OUTLET B I C D Ø INLET H A L E W Fan size A B C D E F H I L W Ø INLET Ø OUTLET Weight [kg] 025 560 388 235 282 477 39 516 414 600 527 250 250 55 031 760 465 283 332 587 39 613 592 800 637 315 315 75 040 760 603 344 396 730 92 739 564 800 780 400 400 102 050 760 737 417 472 899 92 888 528 800 949 500 500 142 Fläkt Woods Oy XXXX GB 2013.01 9 Specifications are subject to alteration without notice

Wiring diagram Fläkt Woods Oy XXXX GB 2013.01 10 Specifications are subject to alteration without notice

Accessories Safety switch SAFE Rain cover GLLZ-77-1-ccc-1-0 The safety isolation switch has been tested to IEC 947-3. It is avaiable in standard version or in ATEX-version and can be supplied either loose or factory-wired. Fan code Motor code Safety Switch GLEB-1-025-3-037-0 APAL-2-00037-1-2-6 SAFE-1-0-0 GLEB-1-031-3-055-0 APAL-4-00055-1-2-6 SAFE-1-0-0 GLEB-1-040-3-110-0 APAL-4-00110-1-2-7 SAFE-1-0-0 GLEB-1-050-3-220-0 APAL-4-00220-1-2-7 SAFE-1-0-0 GLEB-6-025-3-037-0 APAL-2-00037-1-2-6 SAFE-1-0-0 GLEB-6-031-3-055-0 APAL-4-00055-1-2-6 SAFE-1-0-0 GLEB-6-040-3-110-0 APAL-4-00110-1-2-7 SAFE-1-0-0 GLEB-6-050-3-220-0 APAL-4-00220-1-2-7 SAFE-1-0-0 Motors are 3-phase motors suited for frequency converter operation. Suitable frequency converters and codes can be selected from motor table. If the frequency converter is with single-phase supply, the motor must be Δ-connected (3 x230 V). In case of the frequency converter is with threephase supply, the motor must be Y-connected (3x400V). ccc = fan sizes, e.g. 025 Can be ordered as an accessory, installed on to the fan. Pressure controller STYZ-01-10-0-2 FO controls the fan speed via pressure controller PT + PC so that a constant underpressure is maintained in the duct system. Pressure controller guarantees a higher precision compared to pressure switch. PT+PC f2 FO f1 STYR-aa-b-1c-d-1 aa Size look motor table b 1 = 1 phase supply, 1x230 V 3 = 3 phase supply, 3x400 V 1c c1 = FC51 IP21 c2 = FC101 IP54 d 0 = delivered loose 2 = installed to the fan 1 version FF= kitchen exhaust fan FO= frequency converter PT+PC = pressure controller FF Fläkt Woods Oy XXXX GB 2013.01 11 Specifications are subject to alteration without notice

Accessories Air flow measurement GLLZ-09-bbb-1-0, ccc = fan sizes, e.g. 025 The air flow sensor is used for measuring the air flow of the fan. The method is based on pressure differential. The pressure is measured at the specific point in the inlet cone and the reference pressure is measured upstream of the inlet cone. The air flow is calculated from the equation: Flexible connection Q v = Δp m k Qv = airflow (m 3 /s) k = coefficient of the fan (k-factor) Δpm = measured pressure difference (Pa) Flexible connection inlet, std GLLZ-11-1-ccc-1-0 Flexible connection inlet, F400 GLLZ-12-1-ccc-1-0 Flexible connection outlet, std GLLZ-21-1-ccc-1-0 Flexible connection outlet, F400 GLLZ-22-1-ccc-1-0 ccc=fan size, e.g. 025 k-factor table Product K GLEB-1-025-3-037-0 54,39 GLEB-1-031-3-055-0 34,40 GLEB-1-040-3-110-0 21,18 GLEB-1-050-3-220-0 14,87 GLEB-6-025-3-037-0 54,39 GLEB-6-031-3-055-0 34,40 GLEB-6-040-3-110-0 21,18 GLEB-6-050-3-220-0 14,87 Fläkt Woods Oy XXXX GB 2013.01 12 Specifications are subject to alteration without notice

Ordering code Box fan Type 1=standard, 6=F400 Size e.g.031 Motor 3= 3-phase motor Motor power e.g 055=0,55 kw, 110=1.1 kw Version 0 in the beginning GLEB-6-bbb-c-ddd-e Accessories Air flow measurement, 1 nipple ccc = fan size Flexible connection inlet, std ccc = fan size Flexible connection inlet, F400 ccc = fan size Flexible connection outlet, std ccc = fan size Flexible connection outlet, F400 ccc = fan size Rain cover ccc = fan size GLLZ-09-1-ccc-1-0 GLLZ-11-1-ccc-1-0 GLLZ-12-1-ccc-1-0 GLLZ-21-1-ccc-1-0 GLLZ-22-1-ccc-1-0 GLLZ-77-1-ccc-1-0 Safety switch a = 1 1-speed 3-phase motor b = 0 delivered loose SAFE-a-b-0 Pressure controller STYZ-01-10-0-2 aa = see motor table b = 1 1 phase supply 1x230 V 3 3 phase supply 3x400 V 1c = BoxFan c = 1 FC51 IP21 2 FC101 IP54 d = 0 delivered loose 2 installed to the fan e = 1 version STYR-aa-b-1c-d-e Fläkt Woods Oy XXXX GB 2013.01 13 Specifications are subject to alteration without notice

Technical data GLEB-1/6-025-3-037-0 with VSD w/o VSD 800 2900 r/min 35 800 2840 r/min 40!"# 600 2500 53% SFP 1000 600 58%!p t (Pa) 400 2000 SFP 800 40!p t (Pa) 400 50 40 200 1500 70 db(a) 70 db(a) 30 200 30 60 65 SFP 600 60 65 1000 75 75 q v (m 3 /s) 0 q v (m 3 /s) 0 0 0,2 q v (m 3 /s) 0,4 0,6 0 0,2 0,4 0,6 q v (m 3 /s) /h) q v (m 3 /s) /h) q (m 3 /s) 0 m 3 /h 500 1000 1500 2000 0 500 1000 1500 2000 Sound data Fan code Correction Koct (db) K c (db) GLEB-1/6-025-3-037-0 Octave band mid-frequency (Hz) Sound path Speed r/min 63 Hz 125 Hz 250 Hz 500 Hz 1000 Hz 2000 Hz 4000 Hz 8000 Hz Outlet duct 0-1533 23 6 1-5 -12-15 -24-32 Outlet duct 1534-2900 11 4 6-3 -10-12 -20-28 Inlet duct 0-1533 12 8 0-5 -12-13 -16-18 Inlet duct 1534-2900 10 3 0-5 -11-13 -19-20 Surroundings 0-1533 -14-15 -15-20 -20-17 -16-23 -11 Surroundings 1534-2900 -14-20 -13-22 -18-24 -25-28 -15 Motor data Fan code Motor code Motor IEC speed [rpm] Motor power [kw] Voltage [V] Current frequency [Hz] GLEB-1-025-3-037-0 APAL-2-00037-1-2-6 71 2900 0,37 3x230/3x400 1,68/0,97 51,8 55 GLEB-6-025-3-037-0 APAL-2-00037-1-2-6 71 2900 0,37 3x230/3x400 1,68/0,97 51,8 55 Weight [kg] Fan code Motor code 1x230 V Input current 3x400 V Input current Safety switch GLEB-1-025-3-037-0 APAL-2-00037-1-2-6 STYR-14-1-11-d-1 6,1 STYR-14-3-12-d-1 2,1 SAFE-1-0-0 GLEB-6-025-3-037-0 APAL-2-00037-1-2-6 STYR-14-1-11-d-1 6,1 STYR-14-3-12-d-1 2,1 SAFE-1-0-0 Fläkt Woods Oy XXXX GB 2013.01 14 Specifications are subject to alteration without notice

Technical data GLEB-1/6-031-3-055-0 with VSD GLEB-1/6-031-3-055-0 w/o VSD 800 350 2250 r/min 28 50 300 1485 r/min 22 600 2000 53% SFP 1000 250 44%!p t (Pa) 400 200 1800 1480 1200 65 70 75 db(a) 50 80 SFP 800 40 30 SFP 600!p t (Pa) 200 150 100 50 60 65 40 70 db(a) 30 q v (m 3 /s) 0 q v (m 3 /s) 0 0,2 0,4 0,6 0,8 1 q v (m 3 /s) /h) 0 1000 2000 3000 50 50 q v (m 3 /s) 0 0 0,2 0,4 0,6 q v (m 3 /h) /s) q (m 3 /s) 0 1000 2000 Sound data Fan code Correction Koct (db) K c (db) GLEB-1/6-031-3-055-0 Octave band mid-frequency (Hz) Sound path Speed r/min 63 Hz 125 Hz 250 Hz 500 Hz 1000 Hz 2000 Hz 4000 Hz 8000 Hz Outlet duct 0-1533 9 9 3-4 -7-11 -21-25 Outlet duct 1534-2250 8 4 5-4 -7-10 -19-24 Inlet duct 0-1533 5 9 4-1 -8-11 -17-23 Inlet duct 1534-2250 5 4 5-1 -9-10 -16-22 Surroundings 0-1533 -19-13 -2-15 -5-15 -18-20 -3 Surroundings 1534-2250 -22-15 -11-17 -13-18 -24-23 -10 Motor data Fan code Motor code Motor IEC speed [rpm] Motor power [kw] Voltage [V] Current frequency [Hz] GLEB-1-031-3-055-0 APAL-4-00055-1-2-6 80 2200 0,55 3x230/3x400 2,74/1,58 78,6 75 GLEB-6-031-3-055-0 APAL-4-00055-1-2-6 80 2200 0,55 3x230/3x400 2,74/1,58 78,6 75 Weight [kg] Fan code Motor code 1x230 V Input current 3x400 V Input current Safety switch GLEB-1-031-3-055-0 APAL-4-00055-1-2-6 STYR-16-1-11-d-1 11,6 STYR-16-3-12-d-1 2,1 SAFE-1-0-0 GLEB-6-031-3-055-0 APAL-4-00055-1-2-6 STYR-16-1-11-d-1 11,6 STYR-16-3-12-d-1 2,1 SAFE-1-0-0 Fläkt Woods Oy XXXX GB 2013.01 15 Specifications are subject to alteration without notice

Technical data GLEB-1/6-040-3-110-0 with VSD w/o VSD 1000 800 2020 r/min 34 50 55% 600 1485 r/min 33 50 1800 400 56%!p t (Pa) 600 400 200 1480 1200 1000 70 75 80 db(a) 50 SFP 1000 40 30 SFP 800 85!p t (Pa) 200 70 75 80 db(a) 50 40 30 SFP 600 q v (m 3 /s) 0 q v (m 3 /s) 0 0,2 0,4 0,6 0,8 1 1,2 1,4 1,6 q v (m 3 /h) /s) 0 1000 2000 3000 4000 5000 q 0 v (m 3 /s) 0 0,2 0,4 0,6 0,8 1 1,2 q v (m 3 /h) /s) q (m 3 /s) 0 1000 2000 3000 4000 Sound data Fan code Correction Koct (db) K c (db) GLEB-1/6-040-3-110-0 Octave band mid-frequency (Hz) Sound path Speed r/min 63 Hz 125 Hz 250 Hz 500 Hz 1000 Hz 2000 Hz 4000 Hz 8000 Hz Outlet duct 0-1533 8 10 4-5 -7-13 -21-27 Outlet duct 1534-2020 5 4 6-6 -8-13 -20-27 Inlet duct 0-1533 8 11 4 0-8 -12-20 -26 Inlet duct 1534-2020 6 4 4-2 -10-13 -19-26 Surroundings 0-1533 -13-10 -14-12 -4-19 -22-26 -4 Surroundings 1534-2020 -19-15 -14-22 -11-24 -21-22 -11 Motor data Fan code Motor code Motor IEC speed [rpm] Motor power [kw] Voltage [V] Current frequency [Hz] GLEB-1-040-3-110-0 APAL-4-00110-1-2-7 90 2020 1,1 3x230/3x400 4,50/2,60 70,1 102 GLEB-6-040-3-110-0 APAL-4-00110-1-2-7 90 2020 1,1 3x230/3x400 4,50/2,60 70,1 102 Weight [kg] Fan code Motor code 1x230 V Input current 3x400 V Input current Safety switch GLEB-1-040-3-110-0 APAL-4-00110-1-2-7 STYR-18-1-11-d-1 18,7 STYR-18-3-12-d-1 3,5 SAFE-1-0-0 GLEB-6-040-3-110-0 APAL-4-00110-1-2-7 STYR-18-1-11-d-1 18,7 STYR-18-3-12-d-1 3,5 SAFE-1-0-0 Fläkt Woods Oy XXXX GB 2013.01 16 Specifications are subject to alteration without notice

Technical data GLEB-1/6-050-3-220-0 with VSD GLEB-1/6-050-3-220-0 w/o VSD GLEB-1/6-050-3-220-0 1200 800 45 45 1770 r/min 50 1470 r/min 55 1000 60% 600 61% 800 1500 55!p t (Pa) 600 400 200 800 1200 1000 70 75 80 db(a) 50 SFP 1000 40 30 SFP 800!p t (Pa) 400 200 75 80 db(a) 85 40 30 85 SFP 600 0 q v (m 3 /s) 0 0,4 0,8 1,2 1,6 2 2,4 2,8 3,2 q v (m 3 /h) /s) 0 2000 4000 6000 8000 10000 0 q v (m 3 /s) 0 0,4 0,8 1,2 1,6 2 2,4 q v (m 3 /h) /s) 0 2000 4000 6000 8000 Sound data Fan code Correction Koct (db) K c (db) GLEB-1/6-031-3-055-0 Octave band mid-frequency (Hz) Sound path Speed r/min 63 Hz 125 Hz 250 Hz 500 Hz 1000 Hz 2000 Hz 4000 Hz 8000 Hz Outlet duct 0-766 20 8 1-5 -7-14 -17-21 Outlet duct 767-1533 13 9 3-4 -7-12 -17-22 Outlet duct 1534-1770 11 4 5-5 -7-12 -16-21 Inlet duct 0-766 16 8 3-1 -7-12 -15-19 Inlet duct 767-1533 8 10 4-1 -8-11 -15-19 Inlet duct 1534-1770 6 4 5-4 -9-11 -14-18 Surroundings 0-766 -4-5 -14-6 -9-18 -10-12 -4 Surroundings 767-1533 -15-9 -12-11 -13-25 -26-29 -10 Surroundings 1534-1770 -18-12 -10-7 -11-26 -30-32 -7 Motor data Fan code Motor code Motor IEC speed [rpm] Motor power [kw] Voltage [V] Current frequency [Hz] GLEB-1-050-3-220-0 APAL-4-00220-1-2-7 100 1770 2,2 3x230/3x400 8,16/4,71 61,7 142 GLEB-6-050-3-220-0 APAL-4-00220-1-2-7 100 1770 2,2 3x230/3x400 8,16/4,71 61,7 142 Weight [kg] Fan code Motor code 1x230 V Input current 3x400 V Input current Safety switch GLEB-1-050-3-220-0 APAL-4-00220-1-2-7 STYR-19-1-12-d-1 26,4 STYR-19-3-12-d-1 4,7 SAFE-1-0-0 GLEB-6-050-3-220-0 APAL-4-00220-1-2-7 STYR-19-1-12-d-1 26,4 STYR-19-3-12-d-1 4,7 SAFE-1-0-0 Fläkt Woods Oy XXXX GB 2013.01 17 Specifications are subject to alteration without notice

Notes Fläkt Woods Oy XXXX GB 2013.01 18 Specifications are subject to alteration without notice

Notes Fläkt Woods Oy XXXX GB 2013.01 19 Specifications are subject to alteration without notice

We Bring Air to Life Fläkt Woods is a global leader in air management. We specialise in the design and manufacture of a wide range of air climate and air movement solutions. And our collective experience is unrivalled. Our constant aim is to provide systems that precisely deliver required function and performance, as well as maximise energy efficiency. Solutions for all your air climate and air movement needs Fläkt Woods Components supplies a wide range of centrifugal fans for ventilation applications: Centriflow Plus Plug fans with record-breaking efficiency level. Available with wide motor range including integral inverter motors. Roofmaster Roof fans characterised by low sound level. Centrimaster Centrifugal fans single or double inlet, för direct and belt drive. Centrimaster fans with backward curved impellers are characterised by high efficiency and low sound level. GLEB GB 2013.02 Copyright 2013 Fläkt Woods Group Condesign Infocom AB +46 36 29142 10 Fläkt Woods Oy Kalevantie 39, FI-20520 Turku, Finland Tel. 358-20-442 3000 Fax. 358-20-442 3016 www.flaktwoods.com See global website for international sales offices www.flaktwoods.com