PORTSMOUTH MONOBLOCK LAVATORY FAUCET with Speed Connect Drain Installation Instructions 70.0 7.0 Series 7.0 Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect Drain* Fewer parts, installs in less time Never needs adjustment Guaranteed to seal properly the first time, every time. Recommended tools 70.0 Certified to comply with ANSI A.. *Your new American Standard faucet is designed to work only with the Speed Connect drain. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. M90 REV..7 INSTALL FAUCET 70.0 & 7.0 Screwdriver CAUTION Channel Locks Turn off hot and cold water supplies before beginning. Adjustable Wrench Installation with ESCUTCHEON PLATE: Apply a light bead of plumbers putty to underside of ESCUTCHEON PLATE () if mounting surface is uneven. Place ESCUTCHEON PLATE () onto sink or mounting surface. Feed FAUCET SUPPLIES (), MOUNTING STUD () and CABLE ASSEMBLY () through ESCUTCHEON PLATE () and mounting hole of lavatory or mounting surface. Fig. A. Installation less ESCUTCHEON PLATE: Seat SEAL () into under side of FAUCET BASE (). Feed FAUCET SUPPLIES (), MOUNTING STUD () and CABLE ASSEMBLY () through the mounting hole of lavatory or mounting surface. Fig. A. COLLAR ON MOUNTING NUT 7 Fig. C. GROOVE (FAUCET BASE) PUTTY IF REQUIRED MOUNTING SURFACE From below, push GASKET (7) and RETAINING WASHER () onto MOUNTING STUD (). Secure Faucet with MOUNTING NUT (), pulling faucet to front of sink, so SUPPLIES () rests against mounting hole. Before final tightening, make sure collar on MOUNTING NUT () is seated into RETAINING WASHER (). Fig. C. Adjust Faucet so that it is centered. Tighten MOUNTING NUT () to complete faucet mounting.
POP-UP Remove CLEAR PLASTIC COVER (). Remove CARDBOARD SPACER () from under POP-UP (). Tighten TAILPIECE () on BODY before installing BODY. Fig. A. BODY REMOVE FLANGE Thread FLANGE () counter-clockwise and remove FLANGE () and FOAM GASKET () from drain body. Fig. A. Thread LOCKNUT () clock-wise to bottom of drain body. Push GASKET () down against LOCKNUT (). Fig. A. INSTALL FROM BELOW FIXTURE From under side of SINK install BODY () up through drain outlet. REAR OF SINK TIGHTEN LOCKNUT Tighten LOCKNUT () firmly with Adjustable Wrench or Channel Locks. Note: No plumber s putty or caulk is required. The CABLE ATTACHMENT POINT () must face towards the rear of the SINK. Install FOAM GASKET () and FLANGE () onto drain body from above SINK and tighten FLANGE () firmly. OUTLET FLANGE GASKET AND POP-UP KNOB Fig. A. DOWN Check FLANGE in SINK to ensure that WHITE FOAM GASKET () is fully compressed and not visible. Fig. A. POP-UP KNOB () must be fully down. WHITE FOAM GASKET NOT VISIBLE FLANGE M90 REV..7
7 ATTACH CABLE CONNECTOR Fig. A. Thread CABLE CONNECTOR () clockwise onto BODY CONNECTION () and hand tighten. Fig. A. Your new POP-UP installation is now complete. Note: Tailpeice on pop-up drain is -/ O.D. -/ O.D. CHECK OPERATION OF POP-UP Operate LIFT KNOB () to verify that STOPPER () opens and closes. Note: If STOPPER () does not open and close properly then refer to the troubleshooting section of these instructions. 9 MAKE WATER SUPPLY AND WASTE CONNECTIONS Connect FLEXIBLE SUPPLIES (, ) directly to wall supplies. Connection on fitting supplies are /" compression. Connect left SUPPLY () to Hot (Marked with a Red Band) and right supply to COLD () wall supply. Faucet supplies are 0" long from faucet base. Note: If additional supply length is required, installer must purchase additional parts separately. Important: If SUPPLY HOSES (, ) are to long, loop as illustrated to avoid kinking. Connect -/ O.D. tailpiece on POP-UP to waste outlet. APPROX. 0" RED BAND BLUE BAND /" COMPRESSION HOT COLD M90 REV..7
0 TEST INSTALLED FITTING With HANDLE () in OFF position, turn on WATER SUPPLIES () and check all connections for leaks. ON HOT OFF COLD Remove AERATOR (). Operate HANDLE () to flush water lines thoroughly. Replace AERATOR (). CHECK CONNECTIONS Operate POP-UP KNOB () and fill lavatory with water. Check that STOPPER () makes a good seal and retains water in SINK. If STOPPER () does not seal properly, please refer to Troubleshooting section in these instructions. Release POP-UP KNOB () down and check all drain connections and "P" trap for leaks. Tighten if necessary. WASTE OUTLET SERVICE CAUTION Turn off hot and cold water supplies before beginning. To remove or replace cartidge: Fig. A..mm HEX KEY Turn valve to OFF position. Remove HANDLE SCREW (). Pull off HANDLE () and CAP (). Fig. A. Unthread CARTRIDGE NUT () and remove. Pull out CARTEIDGE (). REMOVE Inspect CARTRIDGE () and O-RING (7) for debris and clean if necessary. Clean MANIFOLD () and rinse clean. Reinstall CARTRIDGE () and O-RING (7) onto MANIFLOD (). Reinstall CARTRIDGE NUT (), CAP () and HANDLE ASSEMBLY (). If spout drips, operate handle several times from OFF to ON and HOT to COLD position. Do not force - handles turn only 90. P TRAP INSTALL 70.0 ONLY. SPOUT CAN BE FIXED OR SWIVEL. CONVERT TO A FIXED SPOUT IF DESIRED. To change from swivel to fixed spout, proceed as follows: Remove SET SCREW () using Hex Wrench supplied. VIEW A Install FIXING SET SCREW () using Hex Wrench supplied. Align SPOUT () and tighten SET SCREW () to secure SPOUT (). 7 VIEW "A" CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. M90 REV..7
Speed Connect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position: Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode. CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector () counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration. Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the Stopper should be in the UP position. Fig. B, C. Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C. Re-attach the Cable to the Drain Body Connection () by threading the Cable Connector () clockwise onto the Drain Body Connection () and hand-tighten. Fig. A. Fig. A. Fig. C. RE-ATTACH CAM DOWN DISCONNECT CAM CAP STOPPER STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector () counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration. Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D. Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E. The Stopper can now be removed by lifting it out of the Drain. Fig. F. Fig. D. Fig. E. Fig. F. REMOVE CAM REMOVE CAM CAP M90 REV..7
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, Locked Mode (Stopper cannot be removed) or Unlock Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in Locked mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.fig. G. Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J. Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not snap into place, then rotate the Cam to make sure it is fully inserted. Fig. K. Re-attach Cable. See CABLE ADJUSTMENT PROCEDURE in Troubling Shooting Guide to complete installation. Stopper will be in Locked mode and not be removable. LOGO LOOP TOWARD REAR OF SINK Locked Mode (Vandal Proof) Fig. G. Unlocked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. H. To install the stopper in Unlocked mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down. Fig. H. LOGO 0 Fig. H. Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J. Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not snap into place, then rotate the Cam to make sure it is fully inserted. Fig. K. Re-attach Cable. See CABLE ADJUSTMENT PROCEDURE in Troublingshooting Guide to complete installation. Stopper will be in Unlocked mode and removable. LOOP TOWARD FRONT OF SINK Unlocked Mode Fig. J. Fig. K. CAM INSTALL CAM INSTALL CAM CAP M90 REV..7