Climate and temperature chambers. The Environmental Competence Centre has a number of climate chambers at its disposal to carry out low and high temperature tests, as well as a number of combined climate chambers for low temperatures at high levels of relative humidity. Climate tests are normally carried out according to specific standards such as MIL-STD- 810, MIL-STD-202,IEC-60068, DNV GNV IEC-60529 etc. Temperature/Humidity Chamber Espec 125 Manufacturer: Espec, type PR-2KP -20 C up to +100 C Relative humidity: 20% up to 98% ±0.3 C Humidity accuracy: ±2.5% 1 C/min 3,5 C/min Dimensions of test area: 50 x 50 x 40 cm 2 x 5 cm Microprocessor.
Temperature/Humidity Chamber Espec 800 Manufacturer: Espec, type PL-4ST -40 C up to +100 C Relative humidity: 20% up to 98% ±0.3 C Humidity accuracy: ±2.5% 1 C/min 3,1 C/min Dimensions of test area: 100 x 100 x 80 cm 2 x 10 cm Microprocessor.
Temperature/Humidity Chamber Espec 1100 Manufacturer: Espec, type ARS-1100-75 C up to +180 C Relative humidity: 10% up to 98% ±0.3 C Humidity accuracy: ±2.5% 4.7 C/min 4.1 C/min Dimensions of test area: 110 x 100 x 100 cm 1 x 5 cm 1 x 10 cm Microprocessor.
Temperature/Humidity Chamber CTS TS-70/350 Manufacturer: CTS, type TS-70/ 350-70 C up to +180 C Relative humidity: 10% up to 98% ±0.5 C Humidity accuracy: ±3.0% 2.5 C/min 3.0 C/min Dimensions of test area: 65 x 72 x 75 cm 2 x 10 cm Microprocessor.
Temperature Chamber Espec ARG-680 Manufacturer: Espec, type ARG 680-75 C up to +180 C ±0.5 C 4.2 C/min 6.0 C/min Dimensions of test area: 85 x 100 x 80 cm 2 x 10 cm Microprocessor.
Temperature Chamber CTS TS -70/1250-15 Manufacturer: CTS, type -70/1250-15ARG 680-70 C up to +180 C ±0.3 C 15 C/min 15 C/min Dimensions of test area: 100 x 140 x 87 cm 2 x 10 cm 1 x 5 cm Microprocessor.
Temperature shock facility. Temperature shock tests are carried out amongst others on electronic components and composite products that can be subject to rapid changes in temperature. These tests also give more insight in properties and ageing of the devices examined. Temperature Chamber Weiss, TS130 Manufacturer: Dimensions of test area: Change time Hot/cold chamber: Weiss, type TS130-80 C up to +180 C ±1.0 C 30 C/min 30 C/min 45 x 50 x 60 cm Top, 1 x 5 cm Microprocessor. ±5 sec
Salt fog chamber. Corrosion tests are carried out on products, which will be subjected to sea and industrial climates. The climate chambers allow reproducible and quickened corrosion tests to be carried out according to international specifications. These tests determine corrosion resistance or can help with the application of corrosion protective measures. In the salt mist chamber, constant salt sprinkling tests, as well as test with sprinkle intervals (0-60 min) can be carried out. These tests are performed according to international specifications, like ASTM-117B, MIL-STD-810 and 202, IEC-68 and DIN-50021. In addition the condensation water test according to DIN-50017 can be carried out. Salt spray Chamber SC1000: Manufacturer : Dimensions test area: Weiss, type SC1000 156 x 59 x 70 cm Salt spray +50 C Condense + 45 C ±1 C 1 C/min 3.5 C/min microprocessor 2 x 1 cm
Temperature Vacuum Chamber. The temperature vacuum chamber is intended for carrying out tests on products in the field of extreme cold temperatures in combination with low pressure. Temperature vacuum tests are, amongst others, carried out to simulate air transport conditions for example in accordance with MIL 810 and IEC. Manufacturer : VACUUM SPECIALS Test area dimensions : 0,5 m x 0,5 m x 0,5 m (l x w x h) Maximum load : 20 kg Temperature range : -55 C up to +80 C Temperature accuracy : ± 1 C Min pressure : 10 mbar Max. cooling cap. : 80W Available: Mains power supply: 230 V (50 Hz) Feed through openings and windows
Large climate chamber 1. The large climate chamber is intended for carrying out tests on larger products and systems in the field of extreme temperatures and adjustable relative humidity. In addition solar radiation (1250W/m2) is possible. Climate tests are, amongst others, carried out under the authority of defence, car and aviation industry. Products tested are amongst others, radar systems, shelters, aggregates and vehicles. Manufacturer: Imtech Test area dimensions: 8 m x 6 m x 4.5 m (l x w x h), Entrance: 4.5 m x 4.5 m Entrance lock gate: 1m x 1,95 m Maximum floor load: 1000 kg/m2-60 C till +90 C Climate range: 0-60 C 10-100%RH Dew point range: 1 C till +60 C ±1 C Relative humidity accuracy: ±3% Air speed: 1 m/s Max cooling capacity at -40 C: 30 kw Max cooling capacity at +50 C: 60 kw
Available: Cooling-water: Compressed air: Vehicle exhaust gas removal: Mains power supply : Max mains supply power : 120l/min 300 m3/hr (fresh air) 380 V (50 Hz) 440 V (60 Hz) 416 V (400 Hz) 5 kva (50 Hz) 48 kva (60 Hz) 45 kva (400 Hz) Feed through openings and windows Advanced temperature and humidity control
Large climate chamber 2. Manufacturer: WEISS Test area dimensions: 3 m x 2,5 m x 3 m (l x w x h) Entrance: 1,6 m x 2,5 Entrance lock gate: 0,9m x 2 m Maximum floor load: 250 kg (each wheel) Maximum floor load: 3000 kg/m2 (equal loaded) -40 C till +100 C Dew point range: +5 C till +60 C ±1 C Relative humidity accuracy: ±5% Max cooling capacity: + 50 C < T < 0 C: Linear decreasing from 12 down to 10 kw + 0 C < T < - 30 C: Linear decreasing from 10 down to 2 kw - 30 C < T < -40 C: Linear decreasing from 2 down to 0 kw
Available: Cooling-water: Compressed air Exhaust of fumes Mains power supply : Max mains supply power : 120l/min 380 V (50 Hz) 440 V (60 Hz) 416 V (400 Hz) 5 kva (50 Hz) 48 kva (60 Hz) 45 kva (400 Hz) Feed through openings and windows Advanced temperature and humidity control
Degrees of protection provided by enclosures[ IP Code]. The extent of protection provided by an enclosure against access to hazardous parts, against. Ingress of solid foreign objects and/or against ingress of water and verified by standardized test methods. such as IEC 60529 IP 3X several probes available IPX5,12.5l/min, several water probes available
IPX6 100 l/min Drip-Box