ULTIMATE LUBER Automatic Lubricator The ULTIMATE LUBER is a powerful, motor-driven automatic lubricator which is refillable using standard grease guns. Its microprocessor controlled, energy efficient motor delivers grease to a fixed displacement pump which produces pressures up to 60 bar. This strength allows the ULTIMATE LUBER to drive lubricant through long feed lines and to cycle progressive distributors to feed several bearings consecutively. When a dispensing cycle is selected, the units will activate at programmed intervals. At each interval, the ULTIMATE LUBER dispenses approximately 1.25cc of grease. Neither temperature nor altitude will affect the lubricant output. 500cc 250cc 125cc Most powerful lubricator on the market. Produces up to 60 bar which enables it to service single-point applications up to 9m away and multi-point applications up to 6m. away. Available with long-life replaceable battery packs or optional external power sources. (AC and DC) Available in 3 sizes: (125, 250 or 500cc) Single or Multi-point configuration. Refillable using a standard grease gun. Able to service up to 12 lube points with optional progressive distribution block. Optional remote control available to connect to customer equipment or machinery. (eg. PLC, contactors, relays) Multiple settings from 15 days to 2 years to empty. Optional easy to install mounting plates for both single or multi-point applications available. Designed for the industrial workplace - dust proof - weather-resistant (-15ºC to +55ºC) (NOTE: Low Temp lubricants must be used at low temperatures) Model 500: 23 cm X 13 cm Model 250: 20 cm X 10 cm Model 125: 20 cm X 8 cm. MADE W
TITAN CL LUBER Automatic Lubricator The TITAN CL LUBER is a powerful, motor-driven automatic lubricator which is built on the proven ULTIMATE LUBER technology. The TITAN CL LUBER is refillable by simply replacing a standard grease cartridge. Its microprocessor controlled, energy efficient motor delivers grease to a fixed displacement pump which produces pressures up to 60 bar. This strength allows the TITAN CL LUBER to drive lubricant through long feed lines and to cycle progressive distributors to feed several bearings consecutively. When a valid dispensing cycle is selected, the units will activate at programmed intervals. At each interval, the TITAN CL LUBER dispenses approximately 1.25cc of grease. Neither temperature nor altitude will affect the lubricant output. Most powerful lubricator on the market. Produces up to 60 bar which enables it to service single-point applications up to 9m away and multi-point applications up to 6m away Able to service up to 12 lube points with optional progressive distribution block Available with long-life replaceable battery packs or optional external power sources. (AC and DC) Suitable for indoor/outdoor use Unit is mounted on an easy to install mounting plate LED operation and warning indicators: (1-red, 1-green, 1-blue) Optional Remote Control available to connect to customer equipment or machinery (eg: PLC, Contactors, Relays) 1 GREEN flash every 20 seconds normal operation Multiple settings to empty from 15 days to 2 years. 1 GREEN flash every second (approx.) unit is dispensing grease Single or Multi-Point configuration 1 RED flash every 20 seconds limit switch error (unit operating in failsafe (timed dispense) mode) Refillable using a standard grease cartridge (no other tools needed) 2 RED flashes every 20 seconds Low Battery warning 1 BLUE flash every 20 seconds low grease level (grease cartridge needs to be replaced) 2 BLUE flashes every 20 seconds unit is paused (remote control option) 4 BLUE flashes every 20 seconds Low Temperature, dispensing is paused (-15ºC to 55ºC) (NOTE: Low Temp lubricants must be used at low temperatures) (62cm. h X 15cm. w X 20cm. d). (62cm. h X 45cm. w X 20cm. d).
TITAN OILER 2000 Automatic Lubricator The TITAN OILER 2000 is a po werful, motor-driven automatic lubricator which is built on the proven U LT I M AT E L U B E R t e c h n o l o g y. T h e T I TA N OILER 2000 and its easily refillable, large capacity, 1400cc (47 fl.oz.) tank is perfect for most industrial oiler applications where quality and reliability are needed. Its microprocessor controlled, energy efficient motor delivers oil to a fixed displacement pump which produces pressures up to 135 bar. This strength allows the TITAN OILER 2000 to drive oil through long feed lines and/or through an oil distribution system to feed several applications at the same time. When a valid dispensing cycle is selected, the units will activate at programmed i n t e r v a l s d e l i v e r i n g 2 c c s o f o i l p e r cy cl e. N e i t h e r t em p e r a t u r e n o r a l t i t u d e w i l l a f f e c t the o utput. Most powerful oiler on the market. Produces up to 135 bar which enables it to service single-point applications and multi-point applications at great distances. Available with long-life replaceable battery packs or optional external power sources. (AC and DC) Easily refillable, large capacity tank (1400cc) Easily mounted either stand-alone or on an easy to install mounting plate. Optional remote control available to connect to customer supplied equipment or machinery. (eg: PLC, contactors, relays) Built-in low level sensor; optional low level contact output for customer monitoring. Multiple settings to empty from 15 days to 2 years. (-15ºC to + 55ºC) (NOTE: Low Temp oils must be used in low temperature applications) (30-1/2cm H x 13cm W x 19cm D) Built on proven technology by the Market Leader, ATS ELECTRO-LUBE. Electro-Lubers have been used worldwide since 1982. Designed for the toughest operating environments.
JACK LUBER Automatic Lubricator with Replaceable Cartridge The JACK LUBER is the most versatile product in the ATS product line. I t s b u i l t o n t h e p r o v e n ULTIMATE LUBER technology incorporating the JACKSCREW mechanism. Together, you know it s powerful! The JACK LUBER has a replaceable, one-time use cartridge that changes out in seconds! The drive unit for the JACK LUBER is pure ULTIMATE power and runs off the ATS battery pack or with a direct AC/DC adaptor (optional). Producing over 200 psi, the JACK LUBER is capable of heavy duty applications running long lines; even through a 2 port distribution block. The JACK LUBER is tough, reliable and easy to work with. The JACK LUBER saves time, money and gives you the performance you need and trust from ATS! Self-Contained, stand-alone automatic, single point lubricator. Industry standard 125 and 250cc size. Pressures over 14 bar. 1/2 NPT male grease output. UL/cUL Div. 2 Hazardous Area approval pending. Optional remote control available to connect to customer equipment or machinery. (-40ºC to + 60ºC) Replaceable, one-time use cartridge filled with customer specified lubricant. Designed for the industrial workplace -dust proof -weatherproof (NOTE: Low Temp lubricants must be used at low temperatures) * Patent Pending Multiple settings to empty from 15 days to 2 years. Jack Luber Model 125 7-1/2 high X 3-1/8 dia. May be remote mounted to 40 (12m.) using 3/8 ID hose.
Electro-Luber ORIGAL Automatic Lubricator The classic ELECTRO-LUBER was developed in 1982. The ELECTRO- LUBER uses an electro-chemical reactor cell which converts electrical energy into safe, inert nitrogen gas. The gas is trapped in a hermetically sealed bellows type gas chamber. ATS Electro-Lube was the first company to use this self-contained automatic lubrication technology; as the gas is produced an internal pressure builds up in the bellows and is applied against the orange piston. The piston then forces the lubricant out of the cylinder and into the point of lubrication. The unit can empty between 15 days to 1 year depending on the setting of the simple userprogrammable DIP switch. The selection can be changed or turned off at any time. Jumbo-Luber 475cc Budget-Luber 250cc Mini-Luber 125cc Micro-Luber 60cc Self-Contained, stand-alone automatic, single-point lubricator Continuous lubrication using safe, inert, nitrogen gas. Continuous lubrication of bearings removes and protects foreign matter from entering, slows oxidation, aids in dissipating heat, and ensures a constant supply of fresh lubricant. Available in 4 sizes: (60, 125, 250 or 475cc) Pressures up to 3,4bar A p p r o v e d f o r a l l e x p l o s i v e environments. Certified Intrinsically Safe for Class 1, Groups A,B,C,D,E,F,G. Also certified by MSHA and Energy, Mines Canada for use in mining. ATEX certified units also available. Multiple settings to empty from 15 days to 1 year. Millions of units used worldwide since 1982. May be remote mounted to 1m Optional remote control available to connect to customer equipment or machinery. Filled with customer specified lubricant. Designed for the industrial workplace - dust proof - waterproof to 7m - weatherproof -40ºF to +132ºF (-40ºC to +55ºC) (NOTE: Low Temp lubricants must be used at low temperatures) Jumbo-Luber: 17,.1 cm X 12.1 cm Budget-Luber: 15.5 cm X 10.0 cm Mini-Luber: 14.3 cm X 8.0 cm Micro-Luber: 12.4 cm X 8.0 cm MADE W
ATS ACCESSORIES Legend For Automatic Lubricator A Mounting Plates (single & multi-port) B Replacement battery packs (Ultimate / Titan series) Various high quality Accessories and Replacement parts are available from the factory. These products are always in stock and can be delivered quickly to your site. C AC power supplies (Ultimate / Titan series) D Mounting adapters/reducers Be sure to use GENUE ATS Electro-Lube Accessories and Replacement Parts to ensure the quality performance you have come to trust! E Oil Brush Contact ATS or our partners for further information or to place your order. H Oil Check Valves J F Mounting Brackets G Weather Caps I Hose & Fittings C J Distribution Block (2-12 Ports) H A B I G F D E