FLEXIROC T45 Surface drill rig for quarrying and construction. Folding boom Hole diameter: 89 127 mm (3½" 5") Fixed boom Hole diameter: 89 140 mm 3 ½" 5 ½"
PRECISE POWER HALF THE FUEL CONSUMPTION FIELD STUDIES SHOW THAT THE FLEXIROC T45, DEPENDING ON ROCK CONDITIONS, USES UP TO 50% LESS FUEL THAN ITS PREDECESSOR THE ROC F9 WITHOUT LOSING POWER. The FlexiROC T45 only uses the exact amount of energy that the work demands. Add to that a dependable construction that guarantees high availability, a wide range of use and a cabin environment with the operator in mind and you ve got a machine that will give you the lowest possible costs and the least amount of headaches per cubic meter produced. MAIN BENEFITS Lowest possible fuel consumption and highest possible fuel efficiency Continuously delivers result due to robust hydraulics and reliable control system High availability guaranteed thanks to the dependable construction 2 3
EFFICIENT AND VERSATILE IN ALL CONDITIONS THE FLEXIROC T45 IS DESIGNED AND CONSTRUCTED FOR HIGH PERFOR- MANCE IN CONSTRUCTION WORK. IT IS ALSO AN EFFICIENT ALTERNATIVE FOR MEDIUM SIZE OPEN PIT MINES. EVEN IN THE WORST TERRAIN CONDITIONS, THIS RIG CAN WORK EFFECTIVELY THANKS TO THE REACH OF ITS LONG BOOM AND LOW CENTRE OF GRAVITY. + FLEXIBILITY FOR LONG-TERM PRODUCTIVITY The FlexiROC T45 is equipped with Atlas Copco s dependable and highly productive rock drill control system, COP Logic. Upgradable and prepared for the future, this is the market s most advanced system. A proportional management of feed, torque, and impact enable the rig to drill more efficiently even under the most demanding conditions. TECHNICAL SPECIFICATIONS MAIN COMPONENTS Crawler type two speed undercarriage with track oscillation system Caterpillar turbo charged diesel engine Atlas Copco screw type compressor Dust pre separator Combined warning sound and warning light Fixed boom system/folding boom system Air flow switch Rock drill lubrication system HOLE RANGE Recommended hole range FlexiROC T45 fixed boom T51, T60 89 140 mm 3 ½ 5 ½ FlexiROC T45 folding boom T45, T51 89 127 mm 3 ½ 5 Hydraulic rod handling system for max hole depth, with 4,2 m (14 ) extension rods and a 6,1 m (20 ) starter rod FlexiROC T45 fixed boom T51, T60 35 m 115 Hydraulic rod handling system for max hole depth, with 3,6 m (12 ) extension rods and a 4,2 m (14 ) starter rod FlexiROC T45 folding boom T45, T51 29 m 95 COP Logic Toe-hole drilling system Carousel type rod handling system Hydraulic double drill steel support with movable dust collector hood Double hose drum Dust collection system Operator s cabin, ROPS and FOPS approved ENGINE Caterpillar turbo charged, diesel engine, CAT C9.3/ CAT C9, Tier 4 Final and add blue or Tier 3/Stage IIIA Power rating at 1 900 rpm 242 kw 325 HP CARRIER Tramming speed 3,4 km/h 2,1 mph Track oscillation ±10 ±10 Ground clearance 405 mm 16 4 ATLAS COPCO SERVICE Even the best equipment requires regular service to ensure optimal performance. Atlas Copco provides service solutions to safeguard an optimized relationship between productivity, availability and operational cost. Atlas Copco Mining and Rock Excavation Technique has over 3 300 technicians located in over 80 countries. By combining the usage of Atlas Copco genuine parts with service provided by a certified Atlas Copco technician, you ll have a winning combination no matter of where in the world you operate. + BUILT TO PROTECT YOUR CORE BUSINESS A world-class drill rig has to have a world-class cabin. A comfortable and efficient operator is crucial for maximum productivity. The clean lines of the FlexiROC T45 cabin are the result of a focus on ergonomic user-friendliness. + LESS IS MORE Compared to other rigs on the market, the FlexiROC T45 has 50% fewer hoses and 70% fewer couplings. The advantages are many. This construction reduces the risk for leakage and because hydraulic functions and electronic modules are located in proximity to their function, the components are easier to get at for maintenance. HYDRAULIC ROCK DRILL Rock drill Drill rig Impact power Hydraulic pressure, max Impact rate, max Torque, max Weight approx COP 2560+ FlexiROC T45 folding boom 249 kg 549 lb 187 kg 412 lb 25 kw 33.5 HP 230 bar 3 335 psi 44 Hz 1 555 Nm 1 147 lbf/ft COP 2560EX+ COP 3060 FlexiROC T45 fixed 315 kg 694 lb 30 kw 41 HP 240 bar 3 481 psi 50 Hz 2 450 Nm 1 807 lbf/ft COP 3060EX boom 355 kg 783 lb FEED FLEXIROC T45 WITH FIXED BOOM Hydraulic chain driven aluminum feed with hose guide and double drill steel support with movable lower guide/dust hood DUST COLLECTOR DCT 200 Filter area 20 m 2 215 sq.ft Number of filter elements 20 pcs 20 pcs Suction capacity at 500 mm wg 540 l/s 1 144 cfm Suction hose diam 127 mm 5 Cleaning air pressure, max 7.5 bar 109 psi Cleaning air consumption 2-4 l/pulse 0.06-0.12 cu.ft/pulse FEED FLEXIROC T45 WITH FOLDING BOOM Hydraulic chain driven steel feed with hose guide and double drill steel support with moveable lower guide/dust hood Feed extension 1 900 mm 6 3 Feed extension 1 150 mm 3 9 Feed rate, max 0.9 m/s 177 ft/min Feed rate, max 0.9 m/s 177 ft/min Feed force, max 40 kn 8 992 lbf Feed force, max 20 kn 4 496 lbf Tractive pull, max 50 kn 11 240 lbf Tractive pull, max 30 kn 6 744 lbf Total length 9 500 mm 31 Total length 7 700 mm 25 3 Travel length 5 520 mm 18 2 Travel length 4 610 mm 15 2 VOLUMES Hydraulic oil tank 100 l 36.4 US gal Hydraulic system, total 240 l 63.4 US gal Compressor oil 52 l 13.7 US gal Diesel engine oil 32 l 8.4 US gal Diesel engine, cooling water 75 l 19.8 US gal Diesel engine fuel tank 400 l 105.7 US gal Traction gear 3 l 0.8 US gal Lubrication tank (ECL) 23 l 6.1 US gal AIR CONDITIONER Refrigerant R134a Cooling capacity 5,5 kw Fan suction capacity 125 l/s 265 cfm HYDRAULIC SYSTEM Hydraulic oil cooler Max ambient temperature 50 C 122 F COMPRESSOR Atlas Copco C146-07, screw type compressor Working pressure, max 12 bar 174 psi FAD, at normal working pressure 223 l/s 472 cfm ELECTRICAL SYSTEM Voltage Batteries Alternator Work lights LED type, front Work lights LED type, rear Work lights LED type, feed Warning lamp and reverse buzzer 24 V 2 x 12 V, 185 Ah 28 V, 105 Ah 4 x 3500 Lumen 2 x 3500 Lumen 2 x 5300 Lumen Pumps at 1900 rpm Axial piston pump (1) 160 l/min 42.3 US gal/min Gear pump (2) 120 l/min 31.7 US gal/min Gear pump (3) 40 l/min 10.6 US gal/min Gear pump (4) 40 l/min 10.6 US gal/min Gear pump (5) 40 l/min 10.6 US gal/min Return and drainage filters Filtration rate 10 µm absolute 5
TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS FlexiROC T45 Double hose drums with a slot for each hose extends the life of the hoses and does not require greasing. Ergonomic FOPS/ROPS cabin with great visibility and that is easy to operate. 21 13 1 040 Proven COP 2560 supported by COP Logic rock drill control system. Reduced number of hoses and couplings for better serviceability. 2 700 3 190 2 650 Vertical reach (mm) fixed boom Horizontal reach (mm) fixed boom SAFETY CABIN ROPS and FOPS approved with rubber vibration dampers 2 x wipers with washer Rig inclination indicator Rear view mirror 25 Clear laminated glass (front and roof windows) Fire extinguisher, 6 kg (13 lbs) dry chemical type ABE class III type Clear toughened glass (side and rear windows) Fully adjustable operator s seat Outlet socket, 24 V Prepared with speakers for radio/cd 2 440 25 2 610 Adjustable foot rest Cabin light Combined front mounted platform/tool box Electric combined engine/inclination/hole depth instrument in main computer display 4 815 Horizontal reach (mm) folding boom Vertical reach (mm) folding boom 3 490 7 700 9 500 95 330 3 030 3 030 3 600 5 320 3 600 5 320 2500 Valid for both fixed and folding booom HEIGHT AND LENGTH Fixed boom Height (H1) 3 300 mm 10 8 Length (L1) 10 700 mm 35 2 Folding boom Height (H2) 3 300 mm 10 8 Length (L2) 13 300 mm 43 8 L1 Feed dumped (fixed boom) H1 H2 L2 Feed dumped (folding boom) WEIGHT Standard unit excluding all options and drill steel FlexiROC T45 fixed boom 19 600 kg 43 200 lb FlexiROC T45 folding boom 17 500 kg 38 600 lb SELECTION OF OPTIONS Carrier Hydraulic support leg Hydraulic winch, radio remote controlled with towing eye and wire guides Electric refuelling pump Track chains with single/triple grouser pads Extra LED work lights Water mist system, 225 l Safety cabin Clear laminated glass (front and roof windows) Tinted toughened glass (side and rear windows) Wiper for right hand side window Sun shade kit (rear side and rear windows) Radio/CD Reverse camera Feed Wide feed foot TAC guide tube guides for drill steel support - TAC 64 mm for 64 mm guide tube - TAC 76 mm for 76 mm guide tube - TAC 87 mm for 87 mm guide tube Hole measuring systems Laser receiver upgrading kit GPS compass for parallel holes Lubrication Central lubrication system, type HydroScand Thread greasing devise ECG (with oil) Thread greasing device, brush type (with grease) PAR Oil S PAR Oil M Environment conditions Diesel driven engine heater Artic hydraulic oil, VG 32 Tropical hydraulic oil, VG 68 Biological hydraulic oil, VG 46 Delivered equipment, not mounted Gas charging equipment for rock drill First 50 hours service kit for compressor Conversion kit T45 Conversion kit T51 Conversion kit T60 ROC Manager with bench plan RCS service tool box Electrical tool kit Rock Drill control system Progressive COP Logic 6 7
9851 3414d 2016-05 Örebro, Sweden. Legal Notice Copyright 2015, Atlas Copco Rock Drills AB, Örebro, Sweden. Any unauthorized use or copying of the contents or any part thereof is prohibited. Illustrations and photos may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are subject to change without notice. Consult your Atlas Copco Customer Center for specific information. COMMITTED TO SUSTAINABLE PRODUCTIVITY We stand by our responsibilities towards our customers, towards the environment and the people around us. We make performance stand the test of time. This is what we call Sustainable Productivity. www.atlascopco.com