Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-CH4-EN Available for : ADS-AL CA Rev. Date: August 07, 04 Doc. No.: ##5683## CH4 Version FRançaise disponible en ligne au www.idatalink.com please visit www.idatalink.com/support for complete product details The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 04 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
Page of 0 ADS-AL(DL)-CH4-EN Doc. No.: ##5683## 04074 install type SeLeCtiOn FEATURES MAKE MODEL YEAR VOLKSWAGEN RAM JEEP DODGE CHRYSLER INSTALL TYPE DATA IMMOBILIZER BYPASS PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE POWER LIFTGATE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) DOOR STATUS OUTPUT TRUNK STATUS OUTPUT RAP SHUTDOWN CTRL BRAKE PEDAL STATUS OUTPUT E-BRAKE OUTPUT TACHOMETER OUTPUT DATA/MUX IGNITION CTRL SECURE TAKEOVER PARKING LIGHT CTRL 300 08-0 or Town & Country 08-4 or Caravan 08-0 or Challenger 08-4 or Charger 08-0 or Durango -3 or Grand Caravan 08-4 or Journey 09-0 or Magnum 08 or Commander 08-0 or Grand Cherokee 08-3 or C/V 0-3 or 500 0- or 500 0- or 3500 0- or 4500 - or 5500 - or Routan 09- or Visit our website for advanced features.
Page 3 of 0 ADS-AL(DL)-CH4-EN Doc. No.: ##5683## 04074 type - wiring diagram REFER TO ASSEMBLY FOR PROPER CONNECTIONS AND MATCH EACH LETTER ACCORDINGLY VEHICLE (-) DRIVER DOOR PIN ONLY WHEN RAP SHUTDOWN IS REQUIRED REARM (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT PARKING LIGHT (+) OUTPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM ONLY (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT GROUND WHEN RUNNING (-) OUTPUT REMOTE STARTER OPTIONAL -> PARKING LIGHT (+) OUTPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT IGNITION OUTPUT - PINK GROUND INPUT - BLACK V (+) INPUT - RED/WHITE BRAKE INPUT - ORANGE DO NOT USE THE RED/WHITE WIRE IF YOU ARE PLANNING TO POWER THE VEHICLE POSITIVE PARKLIGHTS WIRE. F DATA MODE LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) ADS-HRN CHTIP ASSEMBLY E D USE DATA MODE OR HARDWIRE MODE A B C DATA MODE E D GWR (-) INPUT - BLUE/WHITE (NC) WHITE (NC) BLACK (NC) RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM ONLY (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK PARKING LIGHT (+) INPUT - WHITE STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE THE BRAKE STATUS WIRE IS FUNCTIONAL ONLY WHEN THE IGNITION IS POWERED. SOLD SEPARATELY VEHICLE HARNESS OR ADS-HRN CH4 ASSEMBLY F E D A B C IF YOUR MODULE HARDWARE IS VERSION.3 OR NEWER YOU CAN ELIMINATE THE RELAY AND CONNECT THE YELLOW WIRE DIRECTLY TO THE VEHICLE A B C G YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - MULTIPLEX PARKING LIGHT OUTPUT 85 87A VEHICLE PARKING LIGHT (MUX) WIRE 87 30 WARNING USE THIS OUTPUT ONLY ON VEHICLES EQUIPPED WITH MUX PARKING LIGHT CONTROL 86 VEHICLE HARNESS SOLD SEPARATELY F G G
Page 4 of 0 ADS-AL(DL)-CH4-EN Doc. No.: ##5683## 04074 type - wire CrOSS reference CHart - OF MAKE MODEL CHRYSLER YEAR WIRE DESCRIPTION NAME COLOR TYPE POSITION DODGE WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR 300 08-0 Town & Country Town & Country 08-0 -4 Caravan 08-0 Challenger 08-4 Charger 08-0 Durango -3 Grand Caravan Grand Caravan 08-0 -4 CanH ~ ~ pin 5 White/Black (DATA) Ignition node ~ Driver Door Pin ~ Black ~ ~ Purple (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White/Brown MUX At switch or driver kick panel ~ Parking Light ~ ~ ~ ~ White/Green MUX Parking light switch ~ CanH ~ ~ pin 5 White/Black (DATA) Ignition node ~ CanH ~ ~ pin 5 White/Black (DATA) Ignition node ~ Driver Door Pin ~ Black ~ ~ Purple (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White/Brown MUX At switch or driver kick panel ~ CanH ~ ~ pin 5 White/LtGreen (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple/Gray (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White MUX Parking light switch ~ Parking Light ~ ~ ~ ~ White/Green MUX Parking light switch ~
Page 5 of 0 ADS-AL(DL)-CH4-EN Doc. No.: ##5683## 04074 type - wire CrOSS reference CHart - OF MAKE DODGE MODEL JEEP YEAR WIRE DESCRIPTION NAME COLOR RAM TYPE POSITION WIRE COLOR VOLKSWAGEN POLARITY MODULE LOCATION COMPONENT LOCATOR Journey 09-0 Magnum 08 Commander 08-0 Grand Cherokee 500 / 500 / 3500 08-3 0-4500 / 5500 - C/V 0 C/V -3 Routan 09- Parking Light ~ ~ ~ ~ White/Purple (+) Passenger kick panel ~ CanH ~ ~ pin 5 White/Black (DATA) Ignition node ~ Driver Door Pin ~ Black ~ ~ Purple (-) Driver kick panel ~ CanH ~ ~ pin 5 White/LtGreen (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver door ~ Parking Light ~ ~ ~ ~ N/A (-) At pin of relay 7 in IPM ~ CanH ~ ~ pin 5 White/LtGreen (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver door ~ Parking Light ~ ~ ~ ~ N/A (-) At pin of relay 7 in IPM ~ CanH ~ ~ pin 5 White/LtGreen (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple/Gray (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White MUX Parking light switch ~ CanH ~ ~ pin 5 White/LtGreen (DATA) Ignition node ~ Driver Door Pin ~ ~ ~ ~ Purple/Gray (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White MUX Parking light switch ~ Parking Light ~ ~ ~ ~ White/Green MUX Parking light switch ~
Page 6 of 0 ADS-AL(DL)-CH4-EN Doc. No.: ##5683## 04074 type - wiring diagram WARNING USE THIS OUTPUT ONLY ON VEHICLES EQUIPPED WITH MUX PARKING LIGHT CONTROL VEHICLE PARKING LIGHT (MUX) WIRE ONLY WHEN RAP SHUTDOWN IS REQUIRED TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT PARKING LIGHT (+) OUTPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM (+) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REMOTE STARTER VEHICLE DRIVER DOOR PIN (-) REQUIRED -> REARM (-) OUTPUT REQUIRED -> PARKING LIGHT (+) OUTPUT REQUIRED -> ST IGNITION (+) INPUT REQUIRED -> BRAKE (+) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT IF YOUR MODULE HARDWARE IS VERSION.3 OR NEWER YOU CAN ELIMINATE THE RELAY AND CONNECT THE YELLOW WIRE DIRECTLY TO THE VEHICLE 5 AMPS 85 87A 87 30 86 N400 DIODE DATA MODE LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM ONLY (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK PARKING LIGHT (+) INPUT - WHITE STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WARNING REMOTE STARTER START OUTPUT MUST BE EXTENDED TO ITS MAXIMUM WHEN USING TACHLESS MODE (CRANK TIME: AT LEAST.5 SECONDS) OR USE TACH CONNECTION INSTEAD WHITE/BLACK - IGNITION (+) VEHICLE SIDE WHITE/RED - IGNITION (+) SIDE WHITE YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - MULTIPLEX PARKING LIGHT OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT VEHICLE SIDE BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - IGNITION (+) INPUT FROM KEY GRAY/YELLOW (NC) WARNING FOR SECURE TAKE OVER, CONNECT THE BRAKE STATUS WIRE TO THE REMOTE STARTER. DO NOT CONNECT TO THE VEHICLE BRAKE WIRE, IT VOIDS THE SECURE TAKE OVER FEATURE. THE BRAKE STATUS WIRE IS FUNCTIONAL ONLY WHEN THE IGNITION IS POWERED. 3 4 5 6 7 8 9 0 IGNITION (+) CANH CANL
Page 7 of 0 ADS-AL(DL)-CH4-EN Doc. No.: ##5683## 04074 installation mode SeLeCtiOn Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARDWIRE MODE Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. module PrOgramming PrOCedUre Close driver door. 6 OFF Turn key to OFF position. Re-open driver door to wake up data bus. 7 Remove key. Insert key into ignition. 8 UNLOCK Press UNLOCK on the OEM remote. 3 ON Turn key to ON position. If vehicle is not equipped with OEM remote, press module programming button. 4 LED will turn solid RED. 9 Wait, LED will turn solid GREEN for seconds. 5 Within 5 seconds, LED will flash GREEN rapidly. 0 Module Programming Procedure completed.
Page 8 of 0 ADS-AL(DL)-CH4-EN Doc. No.: ##5683## 04074 3 module PrOgramming installation PrOCedUre mode SeLeCtiOn - PUSH to Start Press Close driver and release door. programming button to select installation mode. LED flashes (X) once = DATA Re-open MODE driver door to wake up LED flashes (X) twice = STANDARD data bus. HARDWIRE MODE Æ x DO NOT PRESS BRAKE PEDAL Push start button twice [x] to ON position. LED will turn solid RED. 5 6 7 Æ Press DO NOT and PRESS hold BRAKE PEDAL programming button until Push LED start turns button solid once GREEN [x] to to OFF register position. selection. After registration, follow Factory Press UNLOCK Reset Procedure on the OEM to change installation mode and remote. restart this procedure. UNLOCK x Wait, LED will turn solid GREEN for seconds. 4 Within 5 seconds, LED will flash GREEN rapidly. 8 Module Programming Procedure completed.
Page 9 of 0 ADS-AL(DL)-CH4-EN Doc. No.: ##5683## 04074 identify VeHiCLe year Locate the Vehicle Identification Number (VIN) and identify the 0th character. 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Æ Match the VIN s 0th character to its corresponding year. L > 990 S > 995 Y > 000 5 > 005 A > 00 M > 99 T > 996 > 00 6 > 006 B > 0 N > 99 V > 997 > 00 7 > 007 C > 0 P > 993 W > 998 3 > 003 8 > 008 D > 03 R > 994 X > 999 4 > 004 9 > 009 E > 04 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming module diagnostics Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FaCtOry reset PrOCedUre DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7 Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.
Page 0 of 0 ADS-AL(DL)-CH4-EN Doc. No.: ##5683## 04074 warning: read BeFOre remote Starting the VeHiCLe IMPORTANT I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. take OVer PrOCedUre - to the VeHiCLe Owner NOTE I All vehicle doors must be closed and locked prior to remote start sequence. 3 Insert key into ignition. È TIME RESTRICTIºN COMING UP 4 ON Turn key to ON position. Wait seconds for key validation. Press UNLOCK on after-market remote. 5 Press and release BRAKE pedal. TIME RESTRICTIºN Within 45 SECONDS from previous step: Open vehicle door. Enter vehicle. 6 Take over procedure completed. Failure to follow procedure within time restriction will result in vehicle engine shutdown. take OVer PrOCedUre - PUSH to Start - to the VeHiCLe Owner NOTE I All vehicle doors must be closed and locked prior to remote start sequence. 3 Æ x DO NOT PRESS BRAKE PEDAL Push start button twice [x] to ON position. È TIME RESTRICTIºN COMING UP Press UNLOCK on after-market remote. TIME RESTRICTIºN Within 45 SECONDS from previous step: Open vehicle door. Enter vehicle. 4 5 Wait seconds for key validation. Press and release BRAKE pedal. Take over procedure completed. Failure to follow procedure within time restriction will result in vehicle engine shutdown.