MB-825 Flange Mounted

Similar documents
Clutch Coupling. PCC-500 Normal Duty HUB VIEW COLLECTOR RING VIEW. Customer Shall Maintain: Warner Electric ( )

Installation Instructions

Installation Instructions

Primary Clutch/Brake Pin Drive, Spline Drive PCB-825, PCB-1000, PCB-1225 Primary Clutch/Brake Coupling PCBC-825, PCBC-1000, PCBC-1225

Primary Brake Spline Drive Armature PB-825, PB-1000, PB-1225, PB-1525

Installation Instructions

MCS-203 Dancer Control

MCS-203 Dancer Control

PC-500 Clutch, PCC-500 Clutch Coupling, PCBC-500 Clutch/Brake Coupling P-203-WE

TB Series Brakes Tension Control System

SF-120, SF-170, SF-250, SF-400 Bearing Mounted, Flange Mounted, SFC-120, SFC-170, SFC-250, SFC-400 Bearing Mounted, Flange Mounted

SFC-825, SFC-1000, SFC-1225, SFC-1525 Heavy Duty Clutch Coupling and SFC-1525 High Torque Heavy Duty Clutch Coupling

PB-500 Pin Drive, PB-500 Spline Drive PB-650 Pin Drive

Electro-Brake 375, 475, 650, 825, 1000, 1225

Electrically Released Brakes

Primary Brakes PB-120, PB-170, PB-250, PB-400

Electro-Packs EP-170, 250, 400, 500, 825, 1000, 1525

For Dynamic Stopping and Cycling Applications

Electrically Released Brakes FB-375, 475, 650

ATC / ATB Series AT Clutches and Brakes

Introduction to Armature Actuated Brakes (AAB) Operating Principle. Engaged Condition (power off) Disengaged Condition (power on)

ATC / ATB Series AT Clutches and Brakes

EC / EB Series Electro Clutches and Brakes

Gen 2 Clutch/Brake UniModule UM-50, UM-100, UM-180

EB Series Electro Brake

Gen 2 Clutch/Brake UniModule UM-50, UM-100, UM-180

UM Series UniModule. Pre-assembled, C-face Clutches and Brakes. Original Design Sizes 210 & 215. GEN 2 Design Sizes 50, 100 & 180

Preassembled Clutch/Electrically Released Brake Module

AC Motor Brakes. General Information. Features. Add-On Brakes. Spring Applied Power-Off Operation. Motor Brake Coil Current. Mounting.

Preassembled Clutch/Electrically Released Brake Module

Electrically Released Brakes FB-375, 475, 650

EB Series Electro Brake

Blue Max 2000 Vector Duty 2000:1 Constant Torque Motors

Combination Clutch/Brake Packages

Design features of models K and AC brakes. K DC-Powered Brake. AC Three phase Powered Brake

Stearns Super-Mod Totally-Enclosed Non-Ventilated (TENV) Modules Featuring

Electro-Module EM-50, EM-100, EM-180, EM-210, EM-215

Preassembled Clutch/Brake Module

Section 5 MagnaShear (Fully Electric) Motor Brakes

Series 615 through 640; High Bearing Life Design; Nm up to Nm 3-4. Series 645 through 560; High Bearing Life Design; Nm up to Nm 5-6

Inertia of Rotating Parts Lb-Ft 2. Thermal Capacity HPS/Min.*

AT Clutch Major Service Sizes 25, 55, 115

Coil Data Nominal Current MA Nominal VA Sealed Single Pole Normally Open (SPNO) White Rodgers Q

Thermal. Dimensions Torque Rotating. Rotating Capacity lb.ft. HPS/Min. Lb-Ft

CB Series Clutch / Brake

Advanced Technology Tension Clutches

Northstar RIM Tach Steps to Installation. K Wheel (Clamp Style)

SEM SERIES FEATURES SEM 7820 MAGNET SEM FEATURES

Selector Push Button Cat. No. 800T-K2AAXX. a b c d e f g Right Left Right Left. d, e, f, g. Contact Blocks. No contacts on operator

Rigid Metal Conduit, IMC or EMT K-Clamps

M-SERIES MAGNITUDE LIGHTING MAGNETIC DIMMABLE CLASS 2 LED DRIVER QUICK SPECS ENCLOSURE DETAILS

60 Series End-Mount Brake Instructions Standard Housing

PCB Relay. Ordering Information. SPST-NO Type Breaks 10-A Loads; SPST-NO + SPST-NC Type Breaks 8-A Load G6C - - VDC

Table of Contents. Introduction 1 Brake Selection 2

available today from Warner Electric

6. Remove OEM bolts from engine at locations A, B, and C. Lay the wiring off to the side.

COUPLINGS HRC FLEXIBLE COUPLINGS CHAIN SHAFT COUPLINGS SPLINE CLUTCHES TORQUE LIMITERS TORQUE LIMITER COUPLINGS

Procedure to Install the New Autogap components in ER-1225 and ER825 Brake with inverted Armature Hub

General Purpose Relays Types K, R, N, and C

Permanent Magnet Electrically Released Brakes

LCN SEM SERIES FEATURES. SEM 7820 MAGNET Die Cast, Floor mounted. SEM 7870 MAGNET Die Cast, Dual Sided Floor mounted. SEM FEATURES

Eclipse Servo Motor Brake Flange Mounted, Spring Engaged, Air Released Split Hub, Clamp Collar Sizes 2, 3, 4, and 5 ECLIPSE PRODUCTS

Tooth Clutches. Series 5H and 55H-P Pressure Applied Tooth Clutch. Stationary Cylinder for Dry Operation or in Oil. Series 5H and 55H-P

800 T FX 1 A1. Color Cap. No cap 1 Green 2 Black 3 Orange 4 Grey 5 White 6 Red 7 Blue 9 Yellow. Contact Block(s) Operator Position.

Easy Access with Removable Cover Panel

Shaft Mounted Clutches & Brakes

T CLASS T FUSE BLOCKS

Service & Installation Instructions. An Altra Industrial Motion Company P WE Vented. Enclosed Version Optional

Installation Instructions

Stearns Heavy Duty Clutches & Brakes... Rugged, Reliable

NEW BRAKE DESIGN For C-FACE Motors from NEMA Frame Motors

EM Series Electro Module

LINEAR MOTION CONTROL PRODUCTS

Electro Clutches and Brakes Shaft Mounted Clutches and Brakes

PCB Relay. Contact form Terminal Single-side stable Single-winding latching

Northstar RIM Tach Steps to Installation. J Wheel (Spoke Style Wheel)

Table of Contents. Special Application Brakes MARINE/MARITIME/NAVY APPLICATIONS...50 MINING BRAKES - MSHA CERTIFIED...51 ENCODER BRAKES...

INSTRUCTION INFORMATION FOR TYPE "DB" ELECTRIC DISC BRAKE (DB-0, DB-2, DB-4)

80 Series 4 Post Brake Instructions

Powerful + Efficient + Reliable

Corrosion Protection for Electrical Conduit and Fittings

INSTALLATION MANUAL. MB-250, MB-280 and MB-320 Motor Brake INSTALLATION. Force Control Industries, Inc. DESCRIPTION OPERATION

Packaged Electromagnetic Clutches/Brakes

Rigid Couplings. P-1686-TBW 2/17... TB Wood s F7-1

General Purpose Three Phase Motors TEFC (IP55) High Efficiency. Standard Features

3.1. NEMA Manual Starters. Contents Description Types B230, B330, Switches... MS Series, Single-Phase Starters...

1.2. Pushbuttons and Indicating Lights. Contents Description Environmentally Sealed Toggle Switches E10E Product Selection

Bulletin 190-M Compact Starters. Selection Guide

Seismic Sensor Accessories SA, SV & ST 6000 Series

CS24/25 SERIES CLUTCH SHIFT PTO

Crane Control Class 5010

Inverter (Vector) Duty: micromax TM 1000:1 Constant Torque (TENV), 20:1 Constant Torque (TEFC) Totally Enclosed

180VC WITH B5 FLANGE / M ,6 0, / M l 5,0 0,7 192 / M ,0 0,9 223

Four armature sizes. Simple. Powerful. Controllable.

Fractional HP Clutches/Brakes. A-Track Linear Actuators

DC MOTORS NEMA FRAME SCR RATED

COMBISTOP NEW. Spring applied brakes

INSTALLATION MANUAL FOR JABIRU 5100 AIRCRAFT ENGINE

Wrap Spring Clutches and Clutch/Brakes

D4B- N. Safety Interlock Switches. Safety Limit Switch. Specifications. Standards and EC Directives. Certified Standard Ratings D4BN

Transcription:

Motor Brake Normal Duty MB-825 Flange Mounted 1/4-20 UNC-3B (4) on 10.50 dia. 5/16-18 UNC-3B (8) holes equally spaced on 8.85 dia.* 2.68 4.359 1/2-13 UNC-2A (4) on.250 dia.* 10.50 10.50 10.000.156.062 11.515 2.250 Min. 3.35 8.509 8.501 45.43.85 dia. (2) holes 180 apart. Installation * Mounting holes are within.006 of true position. 4.18 5.50 Drive End See Note 4.812 D NEMA Frame Sizes 16 Dim. D 213C & 215C or TC 5.250 254C & 256C or TC 6.250 2.250 Min. 3.500 Shaft Size.500 1.625 Static Torque 80 lb. ft. Maximum Speed 4,000 rpm Standard Voltage D.C. 90 All dimensions are nominal unless otherwise noted. U L Information on inertia and weights begins on page 239. Coil data is on pages 250 and 251. Warner Electric (800-234-3369) QRO (442) 1 95 2 60

Normal Duty Drawing I-2552 Motor Brake MB-825 Flange Mounted 4 3 6 1 2 5-1 8 10 5 9 Item Description Part Number Qty. 1 Cover 5351-288-001 1 2 Bushing* 1 1/2" to 1-5/8" Bore 180-0131 to 180-0149 3 Armature Hub 540-0394 1 4 Armature 5301-111-018 1 5 Magnet - 90 Volt 5351-631-001 1 5-1 Terminal Accessory 5311-101-001 1 6 Adapter 5351-105-001 1 Mounting Accessory 5351-101-003 1 8 Drive Pin and Retainer 5301-101-001 3 9 Mounting Accessory 5321-101-002 1 10 Spring Accessory 5301-101-014 3 How to Order: 1. MB-825 Adapts to NEMA C Face, Double Shaft Motors, Frame Sizes 213 C, 215 C, 254 UC and 256 UC. 2. Specify Bore Size for Item 2. (Frame size determines bore). 3. See Controls Section. Example: MB-825 Motor Brake per I-2552-90 Volt, /8" Bore These units meet the standards of UL508 and are listed under guide card #NMTR2, file #59164. These units are CSA certified under file #LR11543. *See page 252 for specific part numbers. Refer to Service Manual P-208. Warner Electric (800-234-3369) 1 QRO (442) 1 95 2 60

Motor Brake Heavy Duty MB-825 Flange Mounted 1/4-20 UNC-3B (4) holes equally spaced on 10.50 dia. and within.004 of true position. 5/16-18 UNC-3B (8) holes equally spaced on 8.85 dia.* 2.68 4.359 1/2-13 UNC-2A (4) on.250 dia * 10.50 10.50 45.43 10.000.062 2.250 Min. 3.35.156 8.509 8.501 11.515 1/2-14 NPSM Am. Std. straight pipe tap (2) holes 180 apart. Installation 4.18 * Mounting holes are within.006 of true position. 5.50 Drive End See Note 4.812 D NEMA Frame Sizes Dim. D 213C & 215C or TC 5.250 254C & 256C or TC 6.250 2.250 Min. 3.500 Shaft Size.500 1.500 Static Torque Maximum Speed 80 lb. ft. 4,000 rpm Standard Voltage D.C. 90 All dimensions are nominal unless otherwise noted. U L Information on inertia and weights begins on page 239. Coil data is on pages 250 and 251. 18 Warner Electric (800-234-3369) QRO (442) 1 95 2 60

Heavy Duty Drawing I-2556 4 (Shipped Assembled) Motor Brake MB-825 Flange Mounted 4-3 4-4 4-1 4-2 1 4-5 2 6 3 5-1 5 8 Item Description Part Number Qty. 1 Cover 5351-288-001 1 2 Bushing* 1 1/2" to 1-1/2" Bore 180-0002 to 180-0018 3 Armature Hub 540-005 1 4 Armature Assembly 5321-111-001 1 4-1 Armature 5321-111-022 1 4-2 Splined Adapter 104-0008 1 4-3 Autogap Accessory 5321-101-006 1 4-4 Screw 9-022 3 4-5 Locknut 661-0004 3 5 Magnet 5351-631-001 1 5-1 Terminal Accessory 5311-101-001 1 6 Adapter 5351-105-001 1 Mounting Accessory 5351-101-003 1 8 Mounting Accessory 5321-101-002 1 How to Order: 1. MB-825 Adapts to NEMA C Face, Double Shaft Motors, Frame Sizes 213 C, 215 C, 254 UC and 256 UC. 2. Specify Bore Size for Item 4. (Frame size determines bore). 3. See Controls Section. Example: MB-825 Motor Brake per I-2556-90 Volt, /8" Bore These units meet the standards of UL508 and are listed under guide card #NMTR2, file #59164. These units are CSA certified under file #LR11543. *See page 252 for specific part numbers. Refer to Service Manual P-208. Warner Electric (800-234-3369) 19 QRO (442) 1 95 2 60

Motor Brake Normal Duty MB-1000 Flange Mounted 1/4-20 UNC-3B (4) on 12.500 dia. 5/16-18 UNC-3B (8) on 10.625 dia.* 2.68 4.96 1/2-13 UNC-2A (4) on 9.000 dia.* 12.500 12.500 11.50.18.062 13.265 45.593 2.5 Min. 3.50 10.509 10.501 /8 dia. (2) holes 180 apart. Installation 4.50 * Mounting holes are within.006 of true position. 6.625 Drive End See Note 5.43 2.50 Min. 4 Shaft Size.500 2.500 Static Torque 160 lb. ft. Maximum Speed 3,600 rpm Standard Voltage D.C. 90 All dimensions are nominal unless otherwise noted. U L Information on inertia and weights begins on page 239. Coil data is on pages 250 and 251. 180 Warner Electric (800-234-3369) QRO (442) 1 95 2 60

Normal Duty Drawing I-25591 Motor Brake MB-1000 Flange Mounted 4 3 6 1 2 5-1 8 10 5 9 Item Description Part Number Qty. 1 Cover 5352-288-001 1 2 Bushing* 1 1/2" to 2-1/2" Bore 180-0185 to 180-021 3 Armature Hub 540-0313 1 4 Armature 5302-111-013 1 5 Magnet - 90 Volt 5352-631-001 1 5-1 Terminal Accessory 5311-101-001 1 6 Adapter 5352-105-001 1 Mounting Accessory 5351-101-003 1 8 Drive Pin and Retainer 5301-101-001 3 9 Mounting Accessory 5321-101-002 2 10 Spring Accessory 5301-101-014 3 How to Order: 1. MB-1000 Adapts to NEMA C Face, Double Shaft Motors, Frame Sizes 284 UC and 286 UC. 2. Specify Bore Size for Item 2. (Frame size determines bore). 3. See Controls Section. Example: MB-1000 Motor Brake per I-25591-90 Volt, 1-3/8" Bore These units meet the standards of UL508 and are listed under guide card #NMTR2, file #59164. These units are CSA certified under file #LR11543. *See page 252 for specific part numbers. Refer to Service Manual P-208. Warner Electric (800-234-3369) 181 QRO (442) 1 95 2 60

Motor Brake Heavy Duty MB-1000 Flange Mounted 1/4-20 UNC-3B (4) holes equally spaced on 12.500 dia. and within.004 of true position. 5/16-18 UNC-3B (8) on 10.625 dia.* 4.96 1/2-13 UNC-2A (4) holes equally spaced on 9.000 dia.* 12.500 12.500 11.50 3.625 Min. 13.265 45.593 3.50 10.509 10.501 Pilot 1/2-14 NPSM Am. Std. straight pipe tap (2) holes 180 apart. Position hub to this dimension 3.50/3.625 Installation 4.50 * Mounting holes are within.006 of true position. 6.625 Drive End See Note 5.43 2.50 Min. 4 Shaft Size.50 2.68 Static Torque 160 lb. ft. Maximum Speed 3,600 rpm Standard Voltage D.C. 90 All dimensions are nominal unless otherwise noted. U L Information on inertia and weights begins on page 239. Coil data is on pages 250 and 251. 182 Warner Electric (800-234-3369) QRO (442) 1 95 2 60

Heavy Duty Drawing I-25595 Motor Brake MB-1000 Flange Mounted 4 (Shipped Assembled) 4-3 4-4 4-1 4-2 1 4-5 2 6 3 5-1 5 8 Item Description Part Number Qty. 1 Cover 5352-288-001 1 2 Bushing* 1 3/4" to 2-11/16" Bore 180-0026 to 180-005 3 Armature Hub 540-0062 1 4 Armature Assembly 5322-111-002 1 4-1 Armature 5322-111-036 1 4-2 Splined Adapter 104-0009 1 4-3 Autogap Accessory 5322-101-004 1 4-4 Screw 9-022 3 4-5 Locknut 661-0004 3 5 Magnet 5352-631-001 1 5-1 Terminal Accessory 5311-101-001 1 6 Adapter 5352-105-001 1 Mounting Accessory 5351-101-003 2 8 Mounting Accessory 5321-101-002 1 How to Order: 1. MB-1000 Adapts to NEMA C Face, Double Shaft Motors, Frame Sizes 284 UC and 286 UC. 2. Specify Bore Size for Item 4. (Frame size determines bore). 3. See Controls Section. Example: MB-1000 Motor Brake per I-25595-90 Volt, 1-3/8" Bore These units meet the standards of UL508 and are listed under guide card #NMTR2, file #59164. These units are CSA certified under file #LR11543. *See page 252 for specific part numbers. Refer to Service Manual P-208. Warner Electric (800-234-3369) 183 QRO (442) 1 95 2 60

Motor Brake Normal Duty MB-1225 Flange Mounted 1/4-20 UNC-3B (4) holes equally spaced on 15.000 dia. 5/16-18 UNC- 3B (8) holes equally spaced on 13.000 dia.* 2.812 5.296 1/2-13 UNC-2A (4) on 9.000 dia.* 5/16-18 UNC-3B (4) on 11.000 dia.* 15.000 15.000 14.125.093.093 15.03.062 3.250 Min. 45.18 4.062 10.509 10.501 12.509 12.501 Pilot /8 dia. (2) holes 180 apart. Installation 4.93 * Mounting holes are within.006 of true position..843 Drive End See Note 6.85 D 184 U L NEMA Frame Sizes Dim. D 284C & 286C or TC 324C & 326C or TC 8 364C & 365C or TC 9 3.250 Min. 4.125 Shaft Size.500 2.500 Static Torque 260 lb. ft. Maximum Speed 3,000 rpm Standard Voltage D.C. 90 All dimensions are nominal unless otherwise noted. Information on inertia and weights begins on page 239. Coil data is on pages 250 and 251. Warner Electric (800-234-3369) QRO (442) 1 95 2 60

Normal Duty Drawing I-25614 Motor Brake MB-1225 Flange Mounted 4 3 6 1 2 5-1 8 10 5 9 Item Description Part Number Qty. 1 Cover 5353-288-001 1 2 Bushing* 1 1/2" to 2-1/2" Bore 180-0185 to 180-021 3 Armature Hub 540-0014 1 4 Armature 5303-111-009 1 5 Magnet - 90 Volt 5353-631-001 1 5-1 Terminal Accessory 5311-101-001 1 6 Adapter 5353-105-002 1 Mounting Accessory 5351-101-003 1 8 Drive Pin and Retainer 5301-101-001 4 9 Mounting Accessory 5321-101-002 2 10 Spring Accessory 5303-101-006 4 How to Order: 1. MB-1225 Adapts to NEMA C Face, Double Shaft Motors, Frame Sizes 284, 284 UC, 324 UC, 326 UC, 364 UC and 365 UC. 2. Specify Bore Size for Item 2. (Frame size determines bore). 3. See Controls Section. Example: MB-1225 Motor Brake per I-25614-90 Volt, 1-5/8" Bore These units meet the standards of UL508 and are listed under guide card #NMTR2, file #59164. These units are CSA certified under file #LR11543. *See page 252 for specific part numbers. Refer to Service Manual P-208. Warner Electric (800-234-3369) 185 QRO (442) 1 95 2 60

Motor Brake Heavy Duty MB-1225 Flange Mounted 1/4-20 UNC-3B (4) holes equally spaced on 15.000 dia. and within.004 of true position. 5/16-18 UNC-3B (8) on 13.000 dia.* 2.812 5.296 1/2-13 UNC-2A (4) on 9.000 dia.* 15.000 15.000 5/8-16 UNC-2A (4) on 11.000 dia.* 14.125.062.093.093 15.03 45.18 3.250 Min. 4.062 10.509 10.501 Pilot 12.509 12.501 Pilot 1/2-14 NPSM Am. Std. straight pipe tap (2) holes 180 apart. Installation 4.93.843 Drive End See Note 6.85 D NEMA Frame Sizes 186 Dim. D 284C & 286C or TC 324C & 326C or TC 8 364C & 365C or TC 9 3.250 Min. 4.125 Shaft Size.50 2.68 Static Torque Maximum Speed 260 lb. ft. 3,000 rpm Standard Voltage D.C. 90 All dimensions are nominal unless otherwise noted. U L Information on inertia and weights begins on page 239. Coil data is on pages 250 and 251. QRO (442) 1 95 2 60 Warner Electric (800-234-3369)

Heavy Duty Drawing I-25618 4 (Shipped Assembled) Motor Brake MB-1225 Flange Mounted 4-3 4-4 4-1 4-2 1 4-5 2 6 3 5-1 5 8 Item Description Part Number Qty. 1 Cover 5353-288-001 1 2 Bushing* 1 3/4" to 2-11/16" Bore 180-0026 to180-005 3 Armature Hub 540-0064 1 4 Armature Assembly 5323-111-001 1 4-1 Armature 5323-111-034 1 4-2 Splined Adapter 104-0010 1 4-3 Autogap Accessory 5323-101-002 1 4-4 Screw 9-0281 4 4-5 Locknut 661-0005 4 5 Magnet 5353-631-001 1 5-1 Terminal Accessory 5311-101-001 1 6 Adapter 5353-105-002 1 Mounting Accessory 5351-101-003 2 8 Mounting Accessory 5321-101-002 1 How to Order: 1. MB-1225 Adapts to NEMA C Face, Double Shaft Motors, Frame Sizes 284, 284 UC, 324 UC, 326 UC, 364 UC and 365 UC. 2. Specify Bore Size for Item 2. (Frame size determines bore). 3. See Controls Section. Example: MB-1225 Motor Brake per I-25618-90 Volt, 1-5/8" Bore These units meet the standards of UL508 and are listed under guide card #NMTR2, file #59164. These units are CSA certified under file #LR11543. *See page 252 for specific part numbers. Refer to Service Manual P-208. Warner Electric (800-234-3369) 18 QRO (442) 1 95 2 60

2024 © autodocbox.com Privacy Policy | Terms of Service | Feedback