This document is meant to serve as a Quick Set-Up Guide only. Installation manuals referenced below should be downloaded from the NABCO Website and reviewed for complete installation instructions. GT U-0 Electric Lock Retrofit Kit Quick Setup Parts Guide P/N --00 Rev -- Nabco Entrances Inc. S W Gemini Drive Muskego Wisconsin 0 Phone: () - Fax: () - www.nabcoentrances.com Associated Manuals Part Numbers: Electrical Installation Manual **with U0 Microprocessor Controller** (Revision D Software) Rev -0- (P/N -0-0) WARNING Turn OFF all power to the Automatic Door if a Safety System is not working. Instruct the Owner to keep all power turned OFF until corrective action can be achieved by a NABCO trained technician. Failure to follow these practices may result in serious consequences. NEVER leave a Door operating without all Safety detection systems operational. Table of Contents SECTION : RETROFIT THE BELT CLIP... SECTION : INSTALL THE ELECTRIC LOCK... SECTION : U0 WITH FAIL SAFE OR FAIL SECURE ELECTRIC LOCK... SERVICE PARTS: U-0 ELECTRIC LOCK RETROFIT KIT... of
THIS PAGE IS INTENTIONALLY LEFT BLANK
www.nabcoentrances.com GT U-0 Electric Lock Retrofit Kit Quick Setup Parts Guide Rev -- P/N --00 SECTION : Retrofit the Belt Clip Note: Electric Locks can not prevent Breakout. If preventing Breakout is deemed necessary, panic hardware must be fitted to the Door Panels.. Remove () /-0 x inch Hex Head screws used to secure the Belt Clip to the Belt Bracket. Save the spacers, screws and lock washers for reinstallation. a. Ensure the Belt Clip stays intact with the Belt, so the Belt does not lose Belt Tension.. Remove () /-0 x / inch Hex Head screws used to secure the Belt Bracket to the Carrier. Save screws for reinstallation.. Obtain the Belt Clip Assembly provided within the Electric Lock Retrofit Kit.. Review the Belt Clip Assembly to ensure the secured position will match Figure and Figure. a. If necessary rotate the Latch so the Flat Side of Latch faces the located on the Lock Assembly. DN 0 Flat Side of Latch Flat Side of Latch Figure Proper Latch Orientation. Secure the Belt Bracket to the Belt Clip with () /-0 x inch Hex Head screws, lock washers, and spacers that were saved for reinstallation. Do not overtighten the screws. a. Ensure the Belt Clip is in the correct position (Top vs Bottom) as shown in Figure.. Secure the Belt Bracket to the Carrier with () /-0 x / inch Hex Head screws that were saved for reinstallation. Do not overtighten the screws. Power Supply DS 0 Motor U0 Control Belt Clip Top / SINGLE SLIDE DOOR; LHFS, RHFO / Belt Clip Top Belt Bracket U0 Control DS 0 Motor Power Supply SINGLE SLIDE DOOR; RHFS, LHFO DS0 Motor U0 Control Belt Clip Top Power Supply / Belt Clip Bottom DN 0 BI-PART SLIDE DOOR Belt Bracket Figure Belt Clip Location in Full Close Position of
GT U-0 Electric Lock Retrofit Kit Quick Setup Parts Guide www.nabcoentrances.com P/N --00 Rev -- SECTION : Install the Electric Lock. Insert () - x / inch T-Bolts into the Channel located inside Header and turn clockwise so they do not fall out. Insert T-Bolt into Channel DN 0 Turn T-Bolt Clockwise to Lock into Channel Figure Insert Socket Head Cap Screws into Channel. Obtain the Electric Lock provided within the Electric Lock Retrofit Kit.. Place the Electric Lock over the () /- x / inch T-Bolts. a. Ensure the is facing the Pivot side of Slide Door.. Loosely secure the Electric Lock to the T-Bolts with () /- Whizlock nuts.. Position the Electric Lock so the Strike is directly behind the Latch when the Slide door is in the Fully Closed Position. Please see Figure. a. Ensure there is a slight gap between the Strike Wall and Flat of Latch. Strike Latch Strike Wall Slight Gap (Between Strike Wall and Flat of Latch in Full Close Posi on) DN 0 Figure. Tighten () /- Whizlock nuts to secure the Electric Lock to the Channel.. Wire the Electric Lock. Please see Section. Ensure is Facing Pivot Side of Slide Door of
0 H H A M P www.nabcoentrances.com GT U-0 Electric Lock Retrofit Kit Quick Setup Parts Guide Rev -- P/N --00 SECTION : U0 with Fail Safe or Fail Secure Electric Lock Note: Electric Lock only works in One Way mode or Night Mode. HANDY TERMINAL HARNESS P/N - MOTOR/OPERATOR P/N - U0 CONTROL P/N -0-0 POWER SUPPLY P/N - HANDY TERMINAL P No. WARNING 0 T NOISE FILTER MADE IN JAPAN - DS-0 GYRO TECH TB TRANSFORMER ZNR ZNR 0 Microprocessor Controller 0- FUNCTION [SLIDING DOOR] SYMBOL No. VDC+ DCV VDC-(Common) Interior Activation Holding Beam B Reduced Opening Switch Mode Switch (see Mode SW Usage shown left) M0 M Exterior Activation Sequential Activation SQ Breakout Detector BA 0 Sidelite Presence Sensor SLS Contact Output (Class Load only) N/O OUT.A 0V(.Vpeak)max. N/C OUT.B Amax.(0-0V),.Amax.(0-0V) Common OUT.C Auxiliary Output (Open-Collector) OUT VDC-(Common) To protect against risk of fire or electric shock,use only the certified NABCO power supply. MOTOR P Mode SW Usage M0 M MODE Open Open TWO WAY Gnd Open ONE WAY Gnd Gnd HOLD OPEN Open Gnd NIGHT GYRO TECH POWER B RELATED DEVICES P CAUTION BA ERROR Adjustments to the door can only be made with the NABCO Handy Terminal. Do not disassemble the control box. There are no user serviceable parts POWER P INDICATORS 0VAC 0/0Hz >POM< TB To maintain warranty,repairs must be made by authorized NABCO facilities. S ACV ± 0% 0 / 0 Hz POWER SUPPLY HARNESS P/N - 0 VAC BLACK (HOT) WHITE (COMMON) ON/OFF POWER SWITCH AUXILIARY 0 VAC POWER WIRES (THESE WIRES NORMALLY COILED AND TIED UP) GROUND LUG SCREW TO HEADER GROUND HARNESS P/N - FAIL SAFE No. SYMBOL DCV FUNCTION [SLIDING DOOR] 0V BLK WHT RELATED DEVICES - P VDC+ VDC-(COMMON) INTERIOR ACTIVATION HOLDING BEAM B H M0 REDUCED OPENING SWITCH M SQ BA SLS Mode Switch (see Mode SW Usage shown left) GRY VIO GRAY VIOLET Exterior Activation Sequential Activation 0 0 Breakout Detector Sidelite Presence Sensor FAIL SECURE (OUT A) FAIL SAFE (OUT B) OUT.A OUT.B OUT.C N/O N/C Common Contact Output (Class Load only) 0V(.Vpeak)max. Amax.(0-0V),.Amax.(0-0V) OUT Auxiliary Output (Open-Collector) VDC-COMMON TERMINAL ON U0 MAIN HARNESS LABEL ON U0 CONTROL FAIL SECURE LOCK ASSY. P.N. -0-0 WIRING FOR ELECTRIC LOCK ONLY SHOWN P/N - FAIL SAFE LOCK ASSY. P.N. -0-0 OTHER WIRES NOT SHOWN FOR SIMPLICITY U0 ELECTRIC STRIKE OUTPUT SIGNAL HANDY TERMINAL: AUX OUTPUT = 0, OUTPUT TIMER =, ROCKER SWITCH SETTING: ONE WAY OR NIGHT MODE ON OFF ACTIVATION SIGNAL OUTPUT: 0 = ELECTRIC STRIKE OUTPUT ON SEC OFF OUTPUT SIGNAL OPENING OUTPUT TIMER 0 =(DO NOT USE) =(DO NOT USE) =(DO NOT USE) = ELECTRIC STRIKE FUNCTION FULL OPEN OUTPUT TIMER.0 SEC FULLY CLOSED FULLY CLOSED CLOSING of
GT U-0 Electric Lock Retrofit Kit Quick Setup Parts Guide www.nabcoentrances.com P/N --00 Rev -- Service Parts: U-0 ELECTRIC LOCK RETROFIT KIT P/N -0-0 Fail Secure P/N -0-0 Fail Safe * Sold in Parts Bag; P/N -0-0 ** Not sold in Retrofit Kit Front Back DN 0 Header Item Part Finish/Sizes/Notes Description - T-BOLT, / - X. LG -0-0 Fail Secure VON DUPRIN FAIL SEC ELE STRIKE SUB ASSY -0-0 Fail Safe VON DUPRIN FAIL SAFE ELE STRIKE SUB ASSY -00- NUT, WHIZLOCK, /-, ZN -0-0 BELT BRACKET, ELECTRIC LOCK ASSEMBLY -0 SPACER, BELT CLIP, - CLIP, BELT -00-0 / EXTERNAL STAR WASHER -00-0 HHCS, /-0 X, ZN -00- HHCS,/-0 X / of