OEM APPROVED AND USED Pro Form's Pliogrip Truck Line epoxy and urethane adhesives are part of a complete system designed for the most demanding bonding applications in the truck refinish industry. www.proformproducts.com
Simply choose the required working time: PART NO. SIZE TYPE OPEN WORKING SANDING CLAMP APPLICATOR MIXING TIME TIME TIME TIME GUN TIP URETHANE Double Cartridge PF 7773-2 400 ml Urethane 3 minutes 3 minutes 30 minutes 10 minutes PF 815 PF 604 N 13.5 fl.oz. PF 816 PF 7779-2 400 ml Urethane 10 minutes 17 minutes 60 minutes 30 minutes PF 815 PF 604 N 13.5 fl.oz. PF 816 PF 7770-2 400ml Urethane 35 minutes 50 minutes 3 hours 90 minutes PF 815 PF 604 N 13.5 fl.oz. PF 816 PF 7773-3 600 ml Urethane 3 minutes 3 minutes 30 minutes 10 minutes PF 801 PF 604 N 20 fl.oz. PF 7779-3 600 ml Urethane 10 minutes 17 minutes 60 minutes 30 minutes PF 801 PF 604 N 20 fl.oz. PF 7770-3 600 ml Urethane 35 minutes 50 minutes 3 hours 90 minutes PF 801 PF 604 N 20 fl.oz. PF 7277-2 400 ml Flowable 10 minutes 45 minutes PF 815 PF 609 N 13.5 fl.oz. urethane PF 816 EPOXY Double Cartridge and Tube PF 7274-2 400ml Structural 90 minutes 8 hours 4 hours PF 815 PF 609 N 13.5 fl.oz. Epoxy Adhesive PF 816 PF 710-2 400 ml Epoxy 8 minutes 8 minutes 20 minutes PF 815 PF 609 N 13.5 fl.oz. Rigid Parts PF 816 PF 713-2 400 ml Epoxy 8 minutes 8 minutes 20 minutes PF 815 PF 609 N 13.5 fl.oz. Flexible Parts PF 816 PF 702 2 x 150 ml Epoxy 8 minutes 8 minutes 20 minutes 2 x 5 fl.oz. Rigid Parts PF 704 2 x 150 ml Epoxy 8 minutes 8 minutes 20 minutes 2 x 5 fl.oz. Flexible Parts
Pro Form s Pliogrip Truck Line adhesives are recommended and approved at the OEM level. They are used on a daily bases by most truck manufacturers for assembling and bonding panels and parts. This adhesive system is based on curing times and can be used to bond most materials found in the trucking industry. URETHANE ADHESIVE PF 7773 - PF 7779 - PF 7770 Urethane adhesives are two part systems, one part resin and the other a curing agent offering different work time to fit all types of repair. Urethane adhesives offer the ultimate in bond strength and flexibility. They can be used to bond, fill and repair. These adhesives will adhere to most adequately prepared surfaces such as plastics, fibreglass, SMC, aluminum and bare metal. FIBREGLASS MATTING ADHESIVE PF 7277-2 (flowable matting adhesive) Flowable, two part, low viscosity urethane adhesive designed to saturate fibreglass mat or cloth. Ideal for preparing backing patch on fibreglass and SMC repairs. This self-leveling product can also be used to fill small cracks and channels where regular consistency adhesive cannot penetrate. EASY SANDING 100% SOLIDS, DOES NOT SHRINK DIFFERENT CURE TIMES AVAILABLE FLEXIBLE VIBRATION AND FATIGUE RESISTANT EPOXY ADHESIVE PF 7274-2 (parts and panel structural adhesive) Epoxy adhesives PF 7274-2 offers extended work time to easily repair large panels, large surfaces or to be used when longer work time is required. It seals and bonds in one application and offers excellent bond strength and flexibility. It will adhere to most adequately prepared surfaces such as plastics, fibreglass, SMC, aluminum and bare metal. The glass beads mixed in this formulation provide the adequate spacing between parts for optimal bond strength. DOES NOT SHRINK FLEXIBLE LONGER WORK TIME EPOXY REPAIR KIT PF 710-2 - PF 713-2 - PF 702 - PF 704 (for finishing over urethane adhesives and for cosmetic repairs) Epoxy adhesive are an excellent choice for cosmetic repairs on most plastics, fibreglass and SMC. It s smooth and easy to sand formulation also makes it the ideal product for skim coating over urethane based adhesives such as Pliogrip. EXCELLENT SANDING PROPERTIES EASY FEATHEREDGING DRIES FAST NO VOC
DIRECTIONS FOR USE REPAIR PROCEDURES 1. Clean area to be repaired: Metal structure with PF 605 Wax and Grease Remover. Fibreglass, SMC and plastics with PF 606 Plastic Parts Cleaner. 2. Remove rust and paint from surface to be bonded or repaired and bondline using a 36-50 grit abrasive disc. 3. On Fibreglass and SMC repairs, scuff sand and u-groove the area with 36-50 grit abrasive without going through the gel-coat. 4. For panel bonding, straighten and repair part and structure. Check for fit and alignment. 5. For Aluminum parts, scuff sand bondline areas with 180-220 grit. Clean with aluminum prep. Once prepared, bond immediately. Reoccurrence of oxidation will affect bond integrity. 6. Choose the Pliogrip Structural Adhesive that best fits your desired work time. 7. When structural backing or reinforcement is required, use the appropriate structural patch for your repair. Pro Form offers Fibreglass and SMC cloth, Fibreglass mat or Nylon Reinforcing tape. 8. For the front side repair, abrade the surface with a DA sander using an 80 grit disc at low RPM. Visible adhesive from the back side repair must be completely abraded. There should not be any shiny spots. Use a clean dry air source to blow any debris from the surface. Do not use solvent. 9. Use an epoxy adhesive to finish the front side of the repair. For rigid parts use PF 710-2 (or PF 702) for flexible plastics use PF 713-2 (or PF 704). On TPO plastics use PF 612 TPO Adhesion Promoter and follow it s instructions prior of applying epoxy finishing material. COSMETIC REPAIR 1. Cosmetic repairs are recommended for small damages on parts not subjected to stress or vibrations. 2. Clean surface to be repaired as per instructions. Abrade the surface to be repaired with 36-50 grit abrasive. 3. Use a clean dry air source to blow debris from the surface. 4. Apply a thin coat of epoxy adhesive. Let dry for 20 minutes. Sand with 80 grit sandpaper at low speed to remove the glossy film. Build subsequent coats until repair is complete. 5. Let dry completely (approximately 20 minutes). 6. Sand the glossy film with an 80 grit sandpaper and let dry. Allow additional drying time if needed 7. Finish sanding with 180 grit paper then 280 grit and finish with 320 grit sandpaper. 8. Use a clean dry air source to blow debris from the surface. 9. You can now proceed to prime the surface with a high quality non-lacquer based primer. CAUTION Never apply polyester based filler and putty directly on Pro Form Pliogrip Urethane Adhesives. Always use a non-contaminated clean air source to blow debris off the surfaces to be repaired. Products and surfaces must be at normal shop temperatures ( above 21ºC / 70ºF ). Never mix urethane adhesives without mixing nozzle; this will introduce moisture resulting in popping. Do not overheat plastics being repaired. Always sand at low revolution. To store unused adhesives for future applications, leave the mixing nozzle on the cartridge. Ensure the adhesive flows out in a uniform colour every time a new mixing nozzle is used. SMC / FRP must be thoroughly dry before proceeding. In case of any doubt, heat surface gently using a heat gun. Do not overheat. Sanding and grinding at low speed will prevent overheating the repair.
MIXING TIPS SQUARE Mixing Tip Screw type 5" / 12.5 cm nozzle for double cartridges. Ensures a perfect mixture and prevents air entrapment. PART NO. ELEMENTS SHAPE QUANTITY PF 604 N 18 Square 6 PF 611 N 18 Square 100 PF 609 N 24 Square 6 PF 613 N 24 Square 100 Round Mixing Tip Round mixing nozzle to be used with a retaining nut. Ensures a perfect mixture and prevents air entrapment. Will also fit on most competitor double cartridges. PF 609 N PF 604 N PF 609 PART NO. ELEMENTS SHAPE QUANTITY PF 604 18 Round 6 PF 611 18 Round 100 PF 609 24 Round 6 PF 613 24 Round 100 DOUBLE CARTRIDGE APPLICATOR GUNS PF 816 PF 815 PF 801 Heavy duty dispensing gun for double cartridges. Can dispense 2 : 1 and 1 : 1 ratio cartridges of 400 ml without plunger replacement. PF 815 Manual gun PF 816 Air operated gun LARGE REPAIR & BACKING PATCH Air operated applicator gun designed to fit double cartridges of 600 ml. PF 801 Air operated gun Heavy, non-sag, general-purpose resin that can be used on fibreglass and metal. It cures to a hard, non tacky easy to sand surface. PF 175 946 ml / 32 fl. oz PF 175-1 3.78 L / 1 U.S. Gallon Polyester based resin used to repair SMC or fibreglass parts and components. Provides better adhesion, flexibility and faster curing time than regular fibreglass resin. PF 170 946 ml / 32 fl. oz PF 170-1 3.78 L / 1 U.S. Gallon OPEN TIMES SANDING TIME 20 minutes 70 minutes
ACCESSORIES For more information, tips, technical data and MSDS sheets, visit our Web site at: www.proformproducts.com Plastic Parts Cleaner Solvent/ cleaner that removes wax, grease, and silicone from all plastics, SMC, fibreglass and rubber parts. This cleaner can be used safely on all types of plastics and rubber parts. It cleans surfaces without leaving any residue. PF 606 946 ml / 1 U.S. Quart Wax and Grease Remover A strong pre-cleaner solvent to be used on metal at the beginning of the repair cycle. Provides superior cleaning power to remove silicone, wax, oil, grease and other stubborn contaminants. PF 605 3.78 L / 1 U.S. Gallon PF 605-5 18.9 L / 5 U.S. Gallons Urethane Sealer/Adhesive Strong and flexible urethane sealer adhesive that can be applied on bare or painted metals, plastics and fibreglass. This product will resist UV rays and will not shrink like solvent based seam sealers. Recommended for large gap filling and where additional flexibility is required. PF 211 305 ml / 10.3 fl. oz. (Gray) PF 224 305 ml / 10.3 fl. oz. (Black) TPO Adhesion Promoter Adhesion promoter formulated to maximize adhesion between TPO family of plastics and primers, paints or refinishing material. PF 608 118 ml / 4 fl. oz. (Liquid) PF 612 333 g / 11.74 oz. (Aerosol) PF 920 PF 921 PF 922 PF 923 PF 926-27-28 Nylon Reinforcing Tape Self adhesive backing tape to be used when repairing and filling holes or plastic gouges. It can be used with both epoxy and urethane adhesives. PF 920 ( 5 cm x 19.8 m / 2 x 65 ) Plastic Contour Release Film Film to be overlaid on Pliogrip adhesive just after it has been applied to prevent air entrapment. Use this plastic contour release film to force the bead of Pliogrip adhesive into the groove and shape it closely to the original contour of the plastic part. PF 921 ( 12.7 cm x 1.8 m / 5 x 72 ) Structural Backing Patch Combination of fibreglass cloth, fibreglass reinforcing tape and release film designed to provide additional strength to the repair. PF 922 ( 12.7 cm x 1.8 m / 5 x 72 ) Fibreglass and SMC Cloth Material designed to be used with PF 7277-2, fibreglass reinforcment matting. When saturated with this product, the mat becomes an excellent compound to repair holes, cracks, tears and splits on SMC, fibreglass and metal. Will conform to any shape. PF 923 ( 90 cm x 95 cm / 36 x 38 ) Fibreglass Mat Thick woven material designed to be used with PF 175 Fibreglass Resin, PF 170 SMC resin and PF 7277-2 Matting Adhesive. It provides high strength where build up repairs is required. PF 926 ( 45 cm x 95 cm / 18 x 38 ) PF 927 ( 90 cm x 95 cm / 36 x 38 ) PF 928 ( 270 cm x 95 cm / 108 x 38 ) Pro Form Products Ltd, 430 Harrop Drive, Milton, Ontario L9T 3H2 Phone: (905) 878-4990 Fax: (905) 878-1189 1 800 387-7981 www.proformproducts.com