The LNV/Series gas, oil, and combination gas/oil burner is a forced draft packaged burner system. A balanced blower wheel mounted in a fabricated housing provides combustion air for various furnace pressures or high altitude applications. LNVG gas burners, burn gas under a controlled gas/air pressure mix. Gas is emitted from jets surrounding the air stream, producing a turbulent mixture which burns quietly and efficiently. Oil firing features a high pressure atomizing design using simplex nozzles and a separately driven, two stage remote oil pump. Consistent fuel/ air ratio is maintained regardless of firing rate. GENERAL DESCRIPTION U.L. STANDARD EQUIPMENT Product Information Model: LNVG, LNVLG Burner Sizes: 13, 15, 17, 20, 21, 25 Flue gas recirculation (FGR) is drawn through the burner blower assembly properly sized for the required NOx emission levels. An FGR control valve is positioned by the FGR system to provide FGR at all firing rates. An FGR shutoff valve is placed in the FGR line as part of a safety system. This shutoff valve prevents combustible gases from being drawn into the boiler furnace prior to pilot and main flame ignition. Proper operation of this system is proven by three (3) electrical safety interlocks. The system is equipped with ANSI flanges to allow easy installation into the FGR piping. Listed by Underwriters Laboratory. CSD-1, GE Gap, F.M. and other regulatory agency control options are available. Every burner is assembled, wired and tested at the factory. A. CONTROLS 1. Burner mounted control panel 2. 120/1/60 control circuit 3. Motor starter(s). Panel signal lights (See Note 3) 5. Full Modulation firing 6. Fuel changeover switch (combination gas/oil models) 7. Flame safeguard controls 8. Combustion air proving switch 9. Ignition transformer 10. UV Scanner B. OIL SYSTEM 1. Two stage fuel oil pump, separately driven 2. Simplex oil nozzle 3. Oil solenoid valve. S.S.O. oil solenoid valve 5. Oil metering valve C. MAIN GAS SYSTEM (See Note 1) 1. Butterfly rate control valve 2. Safety shutoff valve(s) per code requirements 3. Gas shutoff cocks (2). Main gas regulator D. GAS PILOT SYSTEM 1. Gas-electric interrupted pilot 2. Shutoff cock 3. Separate pilot regulator and valve F. OPTIONAL EQUIPMENT 1. Control circuit transformer 2. Inverted housing arrangement 3. Totally enclosed and 50 cycle motors. Remote mount control panel NOTES 1. All main gas line valves and accessories upstream of butterfly valve are shipped loose 2. Standard motor voltages are 115/208-230/1/60 3. Signal lights: Power On, Main Fuel, Ignition, and Flame Failure ORDERING INFORMATION (SPECIFY) 1. Blower motor voltage, phase and cycle 2. Control circuit voltage (120/1/60 is standard) 3. Burner model and actual firing rate. Flame safeguard control 5. Requirements for special state or local codes in detail 6. Insurance requirements 7. Available gas pressure 8. Firing vessel and furnace pressure Type of fuel determines the model designation Model Fuel LNVG Gas LNVLG No. 2 Oil / Gas E. OTHER EQUIPMENT 1. 350 rpm blower motor 2. Burner mounting flange IC-1522-06/08 Page 1 of 2
Product Information BURNER SIZE CAPACITIES & SPECIFICATIONS 13 15 17 20 21 25 GAS INPUT (Mbtu/hr) (See Note 1) 1,300 1,500 1,700 2,000 2,100 2,500 OIL INPUT (U.S. GPH) (See Note 2) 9.3 10.7 12.1 1.3 15.0 17.9 BOILER HP @ 80% EFF. (See Note 3) 31 36 0 8 50 60 GAS MANIFOLD PRESSURE ( w.c.) (See Note ) 1.5 1.7 2.2 2. 2.6 3.6 BLOWER MOTOR HP (See Note 5) 3/ 3/ 3/ 3/ 3/ 3/ OIL METERING UNIT MOTOR HP 1/3 1/3 1/3 1/3 1/3 1/3 F.G.R. LINE PIPING SIZE (in.) APPROX. SHIPPING WEIGHT (lbs.) 550 550 550 550 550 550 Notes: 1. Gas input based on natural gas at 1,000 Btu/cu.ft. and 0.60 gravity 2. Oil input based on No. 2 oil at 10,000 Btu/gal. 3. Boiler overall efficiency of 80% estimated. Gas pressure based on zero furnace pressure. For total pressure at manifold, add furnace pressure. 5. Blower wheel and motor HP is based on altitude up to 2,000 ft. above sea level. For higher altitude or 50 Hz. applications, consult factory 1/" NPT 16 1/ R15 3/ 12 1/8 8 1/ 12 3/ 11 3/8 10 7/8 3 3/ OIL RETURN OUTLET 15 7/8 29 7/8 26 1 3/8 27 3/ 13 3/8 18 1/2 18 1/ 11 GAS PILOT () HOLES 3/" DIA. ON 11 1/" DIA. B.C. X 90 5 33 5/8 5 1/ 5 11 3/ 3 7/8 9 7 1/ 8 5/8 (8) HOLES 3/" DIA. ON 7 1/2" DIA. B.C. F.G.R. 25 3/8 3 5/8 13 3/8 NOTE 1 - DIMENSIONS ARE FOR REFERENCE ONLY. DIMENSIONS AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. MAIN GAS 1-1/2" NPT 9 7/8 11 1/ DIMENSION DIAGRAM GAS/OIL W/ TOP ELEC. ENCL. LNV-SERIES, MODEL LNVLG, SIZE-1 656-09535 Page 2 of 2 IC-1522-06/08
The LNV/Series gas, oil, and combination gas/oil burner is a forced draft packaged burner system. A balanced blower wheel mounted in a fabricated housing provides combustion air for various furnace pressures or high altitude applications. LNVG gas burners, burn gas under a controlled gas/air pressure mix. Gas is emitted from jets surrounding the air stream, producing a turbulent mixture which burns quietly and efficiently. Oil firing features a high pressure atomizing design using return flow nozzles and a separately driven, two stage remote oil pump. Consistent fuel/ air ratio is maintained regardless of firing rate. GENERAL DESCRIPTION U.L. STANDARD EQUIPMENT Product Information Model: LNVG, LNVLG Burner Sizes: 30, 3, 35, 0, 2, 5, 50 Flue gas recirculation (FGR) is drawn through the burner blower assembly properly sized for the required NOx emission levels. An FGR control valve is positioned by the FGR system to provide FGR at all firing rates. An FGR shutoff valve is placed in the FGR line as part of a safety system. This shutoff valve prevents combustible gases from being drawn into the boiler furnace prior to pilot and main flame ignition. Proper operation of this system is proven by three (3) electrical safety interlocks. The system is equipped with ANSI flanges to allow easy installation into the FGR piping. Listed by Underwriters Laboratory. CSD-1, GE Gap, F.M. and other regulatory agency control options are available. Every burner is assembled, wired and tested at the factory. A. CONTROLS 1. Burner mounted control panel 2. 120/1/60 control circuit 3. Motor starter(s). Panel signal lights (See Note 3) 5. Full Modulation firing 6. Fuel changeover switch (combination gas/oil models) 7. Flame safeguard controls 8. Combustion air proving switch 9. Ignition transformer 10. UV scanner B. OIL SYSTEM 1. Two stage fuel oil pump, separately driven 2. Return flow oil nozzle 3. Oil solenoid valve. S.S.O. oil solenoid valve 5. Oil metering valve C. MAIN GAS SYSTEM (See Note 1) 1. Butterfly rate control valve 2. Safety shutoff valve(s) per code requirements 3. Gas shutoff cocks (2). Main gas regulator D. GAS PILOT SYSTEM 1. Gas-electric interrupted pilot 2. Shutoff cock 3. Separate pilot regulator and valve E. OTHER EQUIPMENT 1. 350 rpm blower motor 2. Burner mounting flange F. OPTIONAL EQUIPMENT 1. Control circuit transformer 2. Inverted housing arrangement 3. Totally enclosed and 50 cycle motors. Remote mount control panel NOTES 1. All main gas line valves and accessories upstream of butterfly valve are shipped loose 2. Standard motor voltages are 115/208-230/1/60 3. Signal lights: Power On, Main Fuel, Ignition, and Flame Failure ORDERING INFORMATION (SPECIFY) 1. Blower motor voltage, phase and cycle 2. Control circuit voltage (120/1/60 is standard) 3. Burner model and actual firing rate. Flame safeguard control 5. Requirements for special state or local codes in detail 6. Insurance requirements 7. Available gas pressure 8. Firing vessel and furnace pressure Type of fuel determines the model designation Model Fuel LNVG Gas LNVLG No. 2 Oil / Gas IC-1523-06/08 Page 1 of 2
Product Information BURNER SIZE CAPACITIES & SPECIFICATIONS 30 3 35 0 2 5 50 GAS INPUT (Mbtu/hr) (See Note 1) 3,000 3,00 3,500,000,200,500 5,000 OIL INPUT (U.S. GPH) (See Note 2) 21. 2.3 25.0 28.6 30.0 32.0 35.7 BOILER HP @ 80% EFF. (See Note 3) 71 81 83 95 100 107 119 GAS MANIFOLD PRESSURE ( w.c.) (See Note ) 3.2 3.9.0.8 6.3 8.1 10. BLOWER MOTOR HP (See Note 5) 2 3 3 3 3 3 3 OIL METERING UNIT MOTOR HP 1/3 1/3 1/3 1/3 1/3 1/3 1/3 F.G.R. LINE PIPING SIZE (in.) APPROX. SHIPPING WEIGHT (lbs.) 600 700 700 700 700 700 700 Notes: 1. Gas input based on natural gas at 1,000 Btu/cu.ft. and 0.60 gravity 2. Oil input based on No. 2 oil at 10,000 Btu/gal. 3. Boiler overall efficiency of 80% estimated. Gas pressure based on zero furnace pressure. For total pressure at manifold, add furnace pressure. 5. Blower wheel and motor HP is based on altitude up to 2,000 ft. above sea level. For higher altitude or 50 Hz. applications, consult factory 1/" NPT R15 3/ 13 1/8 21 10 15 11 7/8 9 3/ 3 3/ OIL RETURN OUTLET 17 1/2 3 5/8 30 5/8 1 7/8 27 3/ 12 7/8 23 1/ 21 1/8 GAS PILOT 12 3/8 () HOLES 3/" DIA. ON 13 1/" DIA. B.C. X 90 5 36 3/8 6 1/8 5 1/8 5 1/ 1 1/2 9 9 11 1/ (8) HOLES 3/" DIA. ON 7 1/2" DIA. B.C. F.G.R. 29 7/8 15 MAIN GAS 2" NPT 10 1/ 11 3/ NOTE 1 - DIMENSIONS ARE FOR REFERENCE ONLY. DIMENSIONS AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. DIMENSION DIAGRAM GAS/OIL W/ TOP ELEC. ENCL. LNV-SERIES, MODEL LNVLG, SIZE-2 656-09536 Page 2 of 2 IC-1523-06/08
The LNV/Series gas, oil, and combination gas/oil burner is a forced draft packaged burner system. A balanced blower wheel mounted in a fabricated housing provides combustion air for various furnace pressures or high altitude applications. LNVG gas burners, burn gas under a controlled gas/air pressure mix. Gas is emitted from jets surrounding the air stream, producing a turbulent mixture which burns quietly and efficiently. Oil firing features a high pressure atomizing design using return flow nozzles and a separately driven, two stage remote oil pump. Consistent fuel/ air ratio is maintained regardless of firing rate. GENERAL DESCRIPTION U.L. STANDARD EQUIPMENT Product Information Model: LNVG, LNVLG Burner Sizes: 5, 55, 60, 63, 70, 80, 8, 90 Flue gas recirculation (FGR) is drawn through the burner blower assembly properly sized for the required NOx emission levels. An FGR control valve is positioned by the FGR system to provide FGR at all firing rates. An FGR shutoff valve is placed in the FGR line as part of a safety system. This shutoff valve prevents combustible gases from being drawn into the boiler furnace prior to pilot and main flame ignition. Proper operation of this system is proven by three (3) electrical safety interlocks. The system is equipped with ANSI flanges to allow easy installation into the FGR piping. Listed by Underwriters Laboratory. CSD-1, GE Gap, F.M. and other regulatory agency control options are available. Every burner is assembled, wired and tested at the factory. A. CONTROLS 1. Burner mounted control panel 2. 120/1/60 control circuit 3. Motor starter(s). Panel signal lights (See Note 3) 5. Full Modulation firing 6. Fuel changeover switch (combination gas/oil models) 7. Flame safeguard controls 8. Combustion air proving switch 9. Ignition transformer 10. UV scanner B. OIL SYSTEM 1. Two stage fuel oil pump, separately driven 3. Return flow oil nozzle 3. Oil solenoid valve. S.S.O. oil solenoid valve 5. Oil metering valve C. MAIN GAS SYSTEM (See Note 1) 1. Butterfly rate control valve 2. Safety shutoff valve(s) per code requirements 3. Gas shutoff cocks (2). Main gas regulator D. GAS PILOT SYSTEM 1. Gas-electric interrupted pilot 2. Shutoff cock 3. Separate pilot regulator and valve F. OPTIONAL EQUIPMENT 1. Control circuit transformer 2. Inverted housing arrangement 3. Totally enclosed and 50 cycle motors. Remote mount control panel NOTES 1. All main gas line valves and accessories upstream of butterfly valve are shipped loose 2. Standard motor voltages are 208-230/60/3/60 3. Signal lights: Power On, Main Fuel, Ignition, and Flame Failure ORDERING INFORMATION (SPECIFY) 1. Blower motor voltage, phase and cycle 2. Control circuit voltage (120/1/60 is standard) 3. Burner model and actual firing rate. Flame safeguard control 5. Requirements for special state or local codes in detail 6. Insurance requirements 7. Available gas pressure 8. Firing vessel and furnace pressure Type of fuel determines the model designation Model Fuel LNVG Gas LNVLG No. 2 Oil / Gas E. OTHER EQUIPMENT 1. 350 rpm blower motor 2. Burner mounting flange IC-152-06/08 Page 1 of 2
Product Information BURNER SIZE CAPACITIES & SPECIFICATIONS 5 55 60 63 70 80 8 90 GAS INPUT (Mbtu/hr) (See Note 1) 5,00 5,500 6,000 6,300 7,000 8,000 8,00 9,000 OIL INPUT (U.S. GPH) (See Note 2) 38.6 39.3 2.9 5.0 50.0 57.1 60.0 6.3 BOILER HP @ 80% EFF. (See Note 3) 129 131 13 150 167 190 200 21 GAS MANIFOLD PRESSURE ( w.c.) (See Note ) 3.0 3.2 3.9.2 5.1 5.6 6.2 7.1 BLOWER MOTOR HP (See Note 5) 5 5 5 5 7 1/2 7 1/2 7 1/2 7 1/2 OIL METERING UNIT MOTOR HP 3/ 3/ 3/ 3/ 3/ 3/ 1 1 F.G.R. LINE PIPING SIZE (in.) APPROX. SHIPPING WEIGHT (lbs.) 800 800 800 800 800 800 800 800 Notes: 1. Gas input based on natural gas at 1,000 Btu/cu.ft. and 0.60 gravity 2. Oil input based on No. 2 oil at 10,000 Btu/gal. 3. Boiler overall efficiency of 80% estimated. Gas pressure based on zero furnace pressure. For total pressure at manifold, add furnace pressure. 5. Blower wheel and motor HP is based on altitude up to 2,000 ft. above sea level. For higher altitude or 50 Hz. applications, 3 1/8 R15 3/ 1 Ø11 1/2 16 3/ 1 3/8 13 7/8 1 1/2 OIL RETURN OUTLET 19 3/ 0 1/ 36 1/ 16 1/8 31 5/8 15 3/8 28 7/8 GAS PILOT 1/2" NPT 25 3/8 15 3/8 () HOLES 3/" DIA. ON 15 1/" DIA. B.C. X 90 5 0 3/8 7 7/8 18 5/8 7 7/8 9 10 1/ 1 5/8 (8) HOLES 3/" DIA. ON 7 1/2" DIA. B.C. F.G.R. 36 7/8 3 3/ 17 1/2 MAIN GAS 2-1/2" NPT 11 1/2 15 1/ NOTE 1 - DIMENSIONS ARE FOR REFERENCE ONLY. DIMENSIONS AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. DIMENSION DIAGRAM GAS/OIL W/ TOP ELEC. ENCL. LNV-SERIES, MODEL LNVLG, SIZE-3 656-09537 Page 2 of 2 IC-152-06/08
The LNV/Series gas, oil, and combination gas/oil burner is a forced draft packaged burner system. A balanced blower wheel mounted in a fabricated housing provides combustion air for various furnace pressures or high altitude applications. LNVG gas burners, burn gas under a controlled gas/air pressure mix. Gas is emitted from jets surrounding the air stream, producing a turbulent mixture which burns quietly and efficiently. Oil firing features a high pressure atomizing design using return flow nozzles and a separately driven, two stage remote oil pump. Consistent fuel/ air ratio is maintained regardless of firing rate. GENERAL DESCRIPTION U.L. STANDARD EQUIPMENT Product Information Model: LNVG, LNVLG Burner Sizes: 100, 105, 110, 120, 126, 17 Flue gas recirculation (FGR) is drawn through the burner blower assembly properly sized for the required NOx emission levels. An FGR control valve is positioned by the FGR system to provide FGR at all firing rates. An FGR shutoff valve is placed in the FGR line as part of a safety system. This shutoff valve prevents combustible gases from being drawn into the boiler furnace prior to pilot and main flame ignition. Proper operation of this system is proven by three (3) electrical safety interlocks. The system is equipped with ANSI flanges to allow easy installation into the FGR piping. Listed by Underwriters Laboratory. CSD-1, GE Gap, F.M. and other regulatory agency control options are available. Every burner is assembled, wired and tested at the factory. A. CONTROLS 1. Burner mounted control panel 2. 120/1/60 control circuit 3. Motor starter(s). Panel signal lights (See Note 3) 5. Full Modulation firing 6. Fuel changeover switch (combination gas/oil models) 7. Flame safeguard controls 8. Combustion air proving switch 9. Ignition transformer 10. UV scanner B. OIL SYSTEM 1. Two stage fuel oil pump, separately driven 3. Return flow oil nozzle 3. Oil solenoid valve. S.S.O. oil solenoid valve 5. Oil metering valve C. MAIN GAS SYSTEM (See Note 1) 1. Butterfly rate control valve 2. Safety shutoff valve(s) per code requirements 3. Gas shutoff cocks (2). Main gas regulator D. GAS PILOT SYSTEM 1. Gas-electric interrupted pilot 2. Shutoff cock 3. Separate pilot regulator and valve E. OTHER EQUIPMENT 1. 350 rpm blower motor 2. Burner mounting flange F. OPTIONAL EQUIPMENT 1. Control circuit transformer 2. Inverted housing arrangement 3. Totally enclosed and 50 cycle motors. Remote mount control panel NOTES 1. All main gas line valves and accessories upstream of butterfly valve are shipped loose 2. Standard motor voltages are 208-230/60/3/60 3. Signal lights: Power On, Main Fuel, Ignition, and Flame Failure ORDERING INFORMATION (SPECIFY) 1. Blower motor voltage, phase and cycle 2. Control circuit voltage (120/1/60 is standard) 3. Burner model and actual firing rate. Flame safeguard control 5. Requirements for special state or local codes in detail 6. Insurance requirements 7. Available gas pressure 8. Firing vessel and furnace pressure Type of fuel determines the model designation Model Fuel LNVG Gas LNVLG No. 2 Oil / Gas IC-1525-06/08 Page 1 of 2
Product Information BURNER SIZE CAPACITIES & SPECIFICATIONS 100 105 110 120 126 17 GAS INPUT (Mbtu/hr) (See Note 1) 10,000 10,500 11,000 12,000 12,600 1,700 OIL INPUT (U.S. GPH) (See Note 2) 71. 75.0 78.6 85.7 90.0 105.0 BOILER HP @ 80% EFF. (See Note 3) 238 250 262 286 300 351 GAS MANIFOLD PRESSURE ( w.c.) (See Note ) 8.2 9.2 10.2 11.8 12.5 TBD BLOWER MOTOR HP (See Note 5) 10 15 15 15 15 15 OIL METERING UNIT MOTOR HP 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 F.G.R. LINE PIPING SIZE (in.) 6 6 6 6 6 6 APPROX. SHIPPING WEIGHT (lbs.) 1550 1550 1550 1550 1550 1550 Notes: 1. Gas input based on natural gas at 1,000 Btu/cu.ft. and 0.60 gravity 2. Oil input based on No. 2 oil at 10,000 Btu/gal. 3. Boiler overall efficiency of 80% estimated. Gas pressure based on zero furnace pressure. For total pressure at manifold, add furnace pressure. 5. Blower wheel and motor HP is based on altitude up to 2,000 ft. above sea level. For higher altitude or 50 Hz. applications, consult factory 39 7/8 R 20 1/3 1 5 1 3/8 Ø13 5/8 17 1/2 1 1/2 13 7/8 OIL RETURN OUTLET 22 5/8 7 5/8 2 5/8 35 1/8 16 1/8 31 5/8 15 3/8 GAS PILOT 1/2" NPT 30 1/ 15 3/8 () HOLES 3/" DIA. ON 15-3/8" DIA. B.C. X 90 5 7 8 7/8 19 3/8 7 7/8 12 3/8 1 5/8 Ø13 1/2 (8) HOLES 15/16" DIA. ON 11 3/" DIA. B.C. F.G.R. 2 3/ 21 1/2 NOTE 1 - DIMENSIONS ARE FOR REFERENCE ONLY. DIMENSIONS AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. MAIN GAS 2-1/2" NPT 11 1/2 15 1/ DIMENSION DIAGRAM GAS/OIL W/ TOP ELEC. ENCL. LNV-SERIES, MODEL LNVLG, SIZE- 656-09538 Page 2 of 2 IC-1525-06/08