Revised 6/01 Hydrants Waterous WB-67-250 The Pacer In 1886, Waterous introduced their line of Frost Jacket fire hydrants. The traffic model WB-67-250 brings the developments of the last one hundred plus years into the 1990's and beyond. It incorporates the strength and durability of a ductile iron lower barrel and conforms to the latest version of AWWA C-502 specifications for dry-barrel fire hydrants. It is easy to maintain and has a proven record of dependability. American-Darling B-84-B The design and construction of every American- Darling 5 1 4" B-84-B fire hydrant provide for maximum water delivery to nozzles with minimum pressure drop. Features which assure years of uninterrupted service include: positive mechanical drain operation; ability to remove complete working parts assembly, including hydrant valve, drain lever and hydrant seat; simple barrel extensions to accommodate grade changes. American-Darling B-62-B Reliability is the most important requirement in a fire hydrant. This means dependable, efficient operation when needed and is the result of quality design and manufacture to rigid specifications. American-Darling B-62-B hydrants incorporate over 80 years experience in design, manufacture and field experience to make available the utmost in reliability. Clow Eddy F-2640 The Eddy hydrant has existed since 1875. The design has proven to be dependable and efficient and one that is easy and simple to maintain. The Eddy's advanced design provides for minimum friction loss and maximum water delivery. Superior engineering, construction and materials assure operational dependability. When the Eddy hydrant does require maintenance, the complete removal and reassembly of the working parts can be accomplished with three ordinary hand tools: an adjustable wrench, a standard screwdriver and pliers. Clow Medallion The Clow Medallion fire hydrant sets new standards for fire protection. The Medallion has earned both Underwriters Laboratory and Factory Mutual approval. It is fully rated for 200 psi working pressure and has a five (5) year limited warranty. Trench or Bury Cover Depth of Trench or Bury = Distance from the ground line to the bottom of the connecting pipe. Depth of Cover = Distance from the ground line to the top of the connecting pipe. Abbreviations Common to Hydrants ANSI... American National Standards Institute AWWA... American Water Works Association; Sets standards only, and does not test or approve any. CI... Cast Iron DI... Ductile Iron FM... Factory Mutual Approved MJ... Mechanical Joint NBR... Nitrile-Butadien Rubber (also known as Nitrile) NRS... Non-Rising Stem NST... National Standard Thread OL... Open Left (counterclockwise) ON... Operating Nut OR... Open Right (clockwise) PR... Pressure Rating PSI... Pounds Per Square Inch SBR... Styrene-Butadien Rubber standard rubber used for all waterworks gaskets UL... Underwriters Laboratories Listed
D-1 Waterous Pacer WB-67-250 D Pacer s Exceptional Features Many years of experience have taught Waterous what customers want in a hydrant. They have applied this knowledge into the Pacer design. As a result it incorporates the best features of all hydrants with additional features not available elsewhere. Pacer is a functionally designed hydrant unmatched in overall convenience. In addition, Pacer meets or exceeds all applicable industry standards. Pacer offers such quality convenience features as: 250 PSI Rating Designed for 250 psi working pressure and tested to 500 psi hydrostatic pressure. All Ductile Iron Construction Its lighter, stronger, smoother and more uniform than hydrants of cast iron construction. 360 Degree Nozzle Rotation The stainless steel retaining ring system allows 360 rotation by merely loosening the flange bolts and turning the nozzle section to the exact position desired. All Bronze Drain No composition, plastic, rubber or leather face to chip, peel or crack. Fusion Bonded Epoxy Coating The interior and exterior of the MJ shoe as well as the upper and lower valve washers are fully coated with fusion applied epoxy. WB-67-250 Specifications Hydrant shall conform to AWWA C-502 Standard for Dry-Barrel Fire Hydrants. Hydrant shall be the traffic model design with replaceable parts designed to break away without water loss and damage to other parts of the hydrant. Hydrant shall be designed for 250 psi working pressure and tested to 500 psi hydrostatic pressure. Main valve opening shall be a minimum of 5¼". The bronze valve seat shall thread into a bronze subseat. The all bronze drain plunger shall be positively operated by the main operating rod. A travel stop nut shall be used to provide a positive limit to the travel of the main operating rod. The hydrant shall have a two piece operating nut for durability and low maintenance. The nozzle section shall be ductile iron and capable of 360 rotation by simply loosening the four ground flange bolts. Nozzles shall be mechanically attached with a ductile iron retainer and sealed with an O-Ring. The upper and lower standpipe and extensions shall be ductile iron with a minimum inside diameter of 7¼". The MJ shoe and upper and lower valve washers shall be fully coated with a fusion applied epoxy. The MJ shoe shall be attached to the lower barrel with stainless steel bolts and nuts. The MJ shoe shall have a flat bottom, ribbed back and strapping lugs to facilitate installation. The hydrant design shall allow plugging of the drains without excavating. depth of bury direction to Open * Product s are for hydrants with drains. Hydrants without drains are available and are stocked at Team EJP locations in states requiring non-draining hydrants. NOTE: Demonstration trailer and training tapes are available if you would like to learn more about the Waterous Pacer WB-67-250 hydrant. The WB-67-250 Hydrant is UL listed and FM approved. * 5' 0" OL 41780 5' 6" OL 41785 6' 0" OL 41790 6' 6" OL 41795 7' 0" OL 41800 7' 6" OL 41805 5' 0" OR 41810 5' 6" OR 41815 6' 0" OR 41825 6' 6" OR 41830 7' 0" OR 41835 7' 6" OR 41840 www.ejprescott.com D-1
D-2 Waterous Pacer WB-67-250 Waterous Pacer WB-67-250 Construction D-2 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-3 Waterous Pacer WB-67-250 D Maintenance Kit WB-67-250 Break Repair Kit This kit is available to assist you in the routine maintenance of hydrants. It includes such items as main valve rubbers, gaskets, O-Rings, nuts, bolts, snap rings and lubricants. description W Hyd. Maintenance Kit 41910 WB-67-250 Top Extension Kit A hydrant so low that connection of a hose is impossible or difficult is a community hazard. The Waterous Top Extension Kit allows for fast and inexpensive extension of the nozzle section, to any desired height (in 6" increments) in case of grade change. description 6" W Hyd. Top Extension 41885 12" W Hyd. Top Extension 41890 18" W Hyd. Top Extension 41895 24" W Hyd. Top Extension 41900 NOTE: Longer length extensions are available by special order. Please call your local Team EJP sales office for price and availability. Need for hydrant repairs is frequently the result of traffic accidents. Since they cannot be eliminated, minimizing the cost of repair is the next best thing. This is being done in many cities by using the Pacer WB-67-250 Traffic Model Hydrant. The Pacer is designed to break away without water loss and without damaging the lower barrel or other vital parts of the hydrant. Repairs can be made without digging or shutting off the water because the Pacer is a true compression hydrant in which the main valve closes with and is held shut by water pressure. The Traffic Repair Kit makes repairs simple and fast. Only the parts which were so designed will break away on impact. Repair is simply a matter of removing the broken parts and installing new parts, all of which are included in the repair kit. description W Hyd. Break Repair Kit DI 41905 www.ejprescott.com D-3
D-4 Waterous Pacer WB-67-250 D-4 WB-67-250 Parts ref. no. 3 O-Ring Packing Buna-N 41958 6A Hex HD Bolt, 5 8" -11 x 3¾" Zinc Pltd. 41957 2 6B Hex HD Bolt, 5 8" x 11 x 3" Zinc Pltd. 41957 6C Hex Nut, 5 8"-11" Zinc Pltd. 41957 1 7 Drain Plunger Red Brass 41912 8 Cotter Pin, ¼" x 1½" Stainless 41980 9A Nozzle Cap Chain, Single Zinc Pltd. 42016 9B Nozzle Cap Chain, Double Zinc Pltd. 42016 1 10A Nozzle Cap, Hose Ductile Iron 41970 10B Nozzle Cap, Pumper Ductile Iron 41955 11A Hose Nozzle Cap Gasket Neoprene 42013 11B Pumper Nozzle Cap Gasket Neoprene 42015 12A Pumper Nozzle Brass 41997 12B Hose Nozzle Brass 41998 16 Flat HD Screw, ¼-20 x ½" Stainless 41971 17A Operating Nut, Lower OR Bronze 42000 17A Operating Nut, Lower OL Bronze 42001 17B Operating Nut, Upper Ductile Iron 42012 25 Valve Rod Bushing Red Brass 41960 29 Standpipe Ductile Iron ** 30 Crossarm Bronze 41987 31 Valve Seat Bronze 41976 34 Upper Valve Washer Ductile Iron 41978 35 Main Valve Rubber Urethane 41979 36 Lower Valve Washer Ductile Iron 41977 37 Hydrant Bottom Ductile Iron 42005 40 Upper Standpipe Ductile Iron 41906 56 Support Wheel Ductile Iron 41992 57 O-Ring (operating nut) Buna-N 41983 59 O-Ring (support wheel) Buna-N 41963 60 Nozzle Section (OR or OL) Ductile Iron 41904 61 Bury Depth Plate Aluminum 41964 61 Bury Depth Plate Washer Pltd. Steel 41965 62B Upper Standpipe Flg. (WB-67-250) Ductile Iron 41989 1 63 Standpipe Flange Ductile Iron 41990 64 Flange Lock Ring Stainless 41991 67 Coupling Sleeve (2 halves) Gray Iron 41974 71 Upper Rod Assembly OR Steel 41975 71 Upper Rod Assembly OL Steel 42003 72 Lower Rod (specify length) Steel 41981 77 O-Ring (upper valve seat) Buna-N 41969 81 Groove Pin 3 32" x 7 16" Ber. Copper 41967 82 Upper Tube Seal Buna-N 41984 83 Lower Tube Seal Buna-N 41985 84 Support Gasket Buna-N 41986 85 Support Tube Ductile Iron 41986 1 86 Stop Nut OL 1"-8 Pltd. Steel 41993 86 Stop Nut OR 1"-8 Pltd. Steel 41994 87 Coupling Nut ½-20 Brass 41973 88 Coupling Stud ½-20 x 2 9 16" Stainless 41972 89 Nozzle Section Bushing Brass 41968 90 Thrust Ring (Starting Jan. 1970) Teflon 41982 92 Upper Standpipe Gasket Neoprene 41996 99 Pipe Plug, ¼" NPT Brass 42017 113 Breakable Flange Ductile Iron 42002 116* O-ring (pumper) Buna-N 42015 2 117* Pumper Nozzle Retainer Ductile Iron 42015 1 118* O-ring (hose nozzle) Buna-N 42014 1 119* Hose Nozzle Retainer Ductile Iron 42014 173 Valve Seat Insert Bronze 174 Valve Seat Insert Gasket Nitrile 176 Stud, 5 8-11 x 5.650" Stainless description material * Not Shown ** Specify the length of the standpipe when ordering. Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-5 American- Darling B-84-B-5 D Sealed Lubrication Chamber Seals operating threads from water and debris which greatly reduces routine maintenance. Top Travel Stop Nut Helps prevent stem buckling and damage to bronze components which may occur if excessive torque is applied in the full open position American Flow Control s American-Darling 5¼" B- 84-B-5 hydrant incorporates more than 80 years of experience in design, manufacture, and field experience. This means dependable and efficient operation when needed. Introduced in 1984, the B-84-B-5 hydrant is rated at 250 p.s.i.g. and is seat tested at 500 p.s.i.g. This hydrant meets or exceeds all requirements of AWWA C502 for dry-barrel hydrants. The B-84-B-5 hydrant is loaded with the features you expect from a high-quality fire hydrant. The all bronze seat and drain ring ensure that the B-84-B-5 hydrant is easily repaired by just one person. Features: Positive compression, fast-closing drains Travel stop located in top of hydrant Bronze-to-bronze seating Short, lightweight, disassembly wrench Easy 360 rotation of nozzle section All bases are epoxy-coated ductile iron Centrifugally cast, high-strength ductile iron lower and upper barrel Sealed lubrication chamber Lower valve ball is epoxy coated Benefits: Spring-Loaded Multiport Drains There are two drain ports and four drain outlets as a standard feature on the B-84-B-5 hydrant. The rod spring assures drains close after approximately three turns of the operating nut. This important safety feature prevents wash-outs that can happen on hydrant designs that do not have this important feature. Specifications: Fire hydrants shall meet or exceed AWWA C502, latest revision. Rated working pressure shall be 250 p.s.i.g., test pressure shall be 500 p.s.i.g., and hydrants shall include the following specific design criteria: The main valve closure shall be of the compression type. Traffic feature to be designed for easy 360º rotation of nozzle section during field installation. The main valve opening shall not be less than 5¼" and be designed so that removal of all working parts can be accomplished without excavating. The bronze seat shall be threaded into mating threads of bronze. The draining system of the hydrant shall be bronze and positively activated by the main operating rod. Hydrant drains shall close completely after no more than three turns of the operating nut. There shall be a minimum of two internal ports and four drain port outlets to the exterior of the hydrant. Drain shutoff to be by direct compression closure. Hydrant barrels shall be made of centrifugally cast ductile iron. Friction loss not to exceed 3.0 p.s.i.g. at 1000 gpm through 4½" pumper nozzle. Hydrants shall be equal to American Flow Control s American- Darling 5¼" B-84-B-5. bury dir. to Open hydrant w/drain hydrant l/drain 5' 0" OL 42682 WD 42682 ND 5' 6" OL 42682 1 WD 42682 1 ND 6' 0" OL 42681 2 WD 42681 2 ND 6' 6" OL 42681 3 WD 42681 3 ND 7' 0" OL 42681 4 WD 42681 4 ND 7' 6" OL 42681 5 WD 42681 5 ND 5' 0" OR 42684 WD 42684 ND 5' 6" OR 42684 1 WD 42684 1 ND 6' 0" OR 42684 2 WD 42684 2 ND 6' 6" OR 42684 3 WD 42684 3 ND 7' 0" OR 42684 4 WD 42684 4 ND 7' 6" OR 42684 5 WD 42684 5 ND WD With drains open ND With drains plugged * Hydrants listed are with 1½" Pentagon operating nut and 2 2½" Hose nozzles and 1 4½" Pumper nozzle all NST (national standard). NOTE: Demonstration trailer and training tapes are available. Please call your local Team EJP sales office for more information. www.ejprescott.com D-5
D-9 American- Darling B-84-B-5 D B-84-B-5 Break Repair Kit B-84-B-5 Top Extension Kit The B-84-B Break Repair Kit makes it a quick and simple job to repair a hydrant that has been damaged by traffic. This kit contains all the parts needed to replace those parts designed to break away upon impact from a vehicle. description B-84-B Hydrant Break Repair Kit 42714 The 5¼" B-84-B hydrant is extended at the barrel flange above the ground line, eliminating any need for excavation. The B-84-B Top Extension Kit (for traffic model hydrants) includes all parts necessary to extend the hydrant. description 6" B-84-B Hydrant Top Extension 42720 12" B-84-B Hydrant Top Extension 42720 1 18" B-84-B Hydrant Top Extension 42720 2 24" B-84-B Hydrant Top Extension 42720 3 NOTES: Longer extension barrels are available by special order. Contact your local Team EJP sales office for price and availability. When extending hydrants, the existing breakable coupling must be moved to the top of the new extension barrel to maintain traffic feature. www.ejprescott.com D-9
D-6 American- Darling B-84-B-5 5¼" B-84-B-5 Fire Hydrant Construction D-6 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-7 American- Darling B-84-B-5 D B-84-B-5 Parts Illustration www.ejprescott.com D-7
D-8 American- Darling B-84-B-5 Parts List For 5¼" B-84-B-5 Fire Hydrant How to Order Parts The part shown should be prefixed by the following s to designate the size and model of hydrant: 54 for 5¼" valve opening 45 for 4½" valve opening EXAMPLE: 5¼" Operating Nut 54-84-1 notes: 1. Size and shape of nut on operating nut and cap, threading on nozzles and caps and the direction of opening made to specifications. 2. Cap chains not furnished unless specified. 3. All gray iron is ASTM A126 class B. 4. Bolts and nuts are rustproofed steel ASTM A307 in accordance with AWWA C502. 5. Working pressure 250 psig, test pressure 500 psig. 6. Hydrant conforms to AWWA Standard C502. 7. Upper barrel can be rotated 360. 8. Factory Mutual Approved and Underwriters Laboratories Listed at 200 psig in allowable configurations. 9. Bronze in contact with water contains less than 16% zinc. 10. 6" Mechanical joint base is ductile iron. 11. Nominal turns to open is 19½. part no. qty description material 84-1 1 Operating Nut OR Bronze 42718 02 84-1 1 Operating Nut OL Bronze 42718 01 84-2-1 1 Cover O-ring Buna-N 42718 03 84-2-2 2 Housing O-ring Buna-N 42718 04 84-4-4 1 Thrust Washer Nylatron 42718 05 84-5-3 1 Pipe Plug Stainless Steel 42718 06 84-7-7 1 Weather Cover OL Gray Iron 42718 071 84-7-7 1 Weather Cover OR Cast Iron 42718 072 84-9 1 Housing Cover OR-OL Gray Iron 42718 10 84-11-2 4 Housing Cover Cap Screw See Note 4 42718 11 84-13 1 Housing Cover Gasket Fiber 42718 08 84-14 1 Housing Gasket Composition Rubber 42718 09 84-15 1 Housing Ductile Iron 42718 12 84-16 6 Housing Bolt and Nut See Note 4 42718 13 84-18-60 1 Upper Barrel w/steamer Ductile Iron 42718 141 84-19-SR 1 Lower Barrel Ductile Iron 42718 17 84-20-60 2 2 1 2" Hose Nozzle NST Bronze (See Note 9) 42718 151 84-20-61 2 Hose Nozzle O-Ring Buna-N 42718 161 84-20-62 2 Hose Nozzle Retainer Ductile Iron 42718 162 84-20-63 2 Hose Nozzle Washer Teflon 42718 163 84-21 2 Hose Cap Gray Iron 42718 18 84-22 2 Hose Cap Gasket Rubber 42718 19 84-23-1 1 Per Nozzle Nozzle Cap Chain Steel 42700 24 84-23-2 1 Per Nozzle Cap Chain S-Hook Steel 42700 241 84-25-60 1 or 0 Pumper Nozzle Bronze (See Note 9) 42718 221 84-25-61 1 Per Nozzle Pumper Nozzle O-Ring Buna-N 42718 201 84-25-62 1 Per Nozzle Pumper Nozzle Retainer Ductile Iron 42718 202 84-25-63 1 Per Nozzle Pumper Nozzle Washer Teflon 42718 203 84-26 1 Per Nozzle Pumper Cap Gray Iron 42718 23 84-27 1 Per Nozzle Pumper Cap Gasket Rubber 42718 241 84-29-13 2 Non-Breakable Flange Ductile Iron 42718 25 84-29-14 2 Snap Ring Stainless Steel 42718 26 84-29-30 1 Break Rod Coupling Gray Iron 42718 27 84-29-31 2 Rod Cplg. Pin and Clip Pins Stainless/Bronze 42718 28 84-29-45 1 Breakable Barrel Flange Gray Iron 42718 29 84-30-03 1 Hydrant Spring Spring Steel 42718 30 84-30-04 1 Spring Plate Steel 42718 31 84-30-06 1 Travel Stop Nut OL Bronze (See Note 9) 42718 38 84-30-06 1 Travel Stop Nut OR Bronze (See Note 9) 42718 39 84-30-07 1 Spring Plate Pin Steel 42718 40 84-30-11 1 Upper Hydrant Rod OR Steel 42718 41 84-30-11 1 Upper Hydrant Rod OL Steel 42718 411 84-30-12 1 Lower Hydrant Rod Steel 42718 42 84-31 1 Drain Lever Bronze (See Note 9) 42718 43 84-33 2 Drain Lever Washer Rubber 42718 44 84-34 2 Drain Lever Rivet Brass 42718 45 84-35-02 1 Hydrant Seat Solid Bronze (See Note 9) 42718 46LD 84-35-02 1 Hydrant Seat Draining Bronze (See Note 9) 42718 46WD 84-36-1 2 Seat O-ring Buna-N 42718 47 84-37 1 Drain Ring Bronze (See Note 9) 42718 48 84-38 2 Drain Ring Gasket Composition Rubber 42718 49 84-38-1 1 Barrel Gasket Composition Rubber 42718 52 84-39 8 Base Bolt and Nut Stainless Steel 42718 53 84-39-9 8 Barrel Bolt and Nut See Note 4 42718 54 84-40 1 Hydrant Valve Top Gray Iron 42718 55 84-40-4 1 Cotter Pin Stainless Steel 42718 551 84-41 1 Hydrant Valve Rubber 42718 50 84-42 1 Hydrant Valve Bottom Ductile Iron 42718 51 84-46-5 1 6" Mechanical Joint Base Ductile Iron 42718 56 84-144 1 Weather Shield Rubber 42718 57 84-147 1 Seat Wrench Cast Iron 42718 60 84-149 1 Hose Nozzle Wrench Cast Iron 42718 601 84-150 1 Pumper Nozzle Wrench Cast Iron 42718 602 D-8 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-10 American- Darling B-62-B-5 Sealed Lubrication Chamber Seals operating threads from grit and moisture and reduces maintenance. Top Travel Stop Nut Helps prevent stem buckling and damage to bronze components which may occur if excessive torque is applied in the full open position. American Flow Control s American- Darling B-62-B-5 hydrant incorporates over 80 years in design, manufacture, and field experience. This means dependable and efficient operation when needed. Introduced in 1962, the B-62-B-5 hydrant is rated at 200 p.s.i.g. and seat tested at 400 p.s.i.g. This hydrant meets and exceeds all requirements of AWWA C502 for dry-barrel hydrants. The B-62-B-5 hydrant is loaded with the features you expect from a high quality fire hydrant. The all bronze seat and bronze drain ring assure that the B-62-B-5 hydrant is easily repaired by just one person. Standard Features: Travel stop located in top of hydrant Bronze-to-bronze seating Positive compression, spring-loaded multiport drains Lower valve ball is epoxy coated Short, lightweight, disassembly wrench Easy 360 rotation of nozzle section Centrifugally cast high-strength ductile iron barrels Ductile iron 6" base with epoxy-coating Sealed lubrication chamber Double O-ring protected bronze valve seat Benefits: Spring-Loaded Multiport Drains Three drain ports and four drain outlets are standard features on the B-62- -B-5 hydrant. The rod spring assures drains close after only three turns of the rod. This important safety feature prevents wash-outs that can happen on hydrant designs that do not have this important feature. Specifications: Fire hydrants shall meet or exceed AWWA C502, latest revision. Rated working pressure shall be 200 p.s.i.g., test pressure shall be 400 p.s.i.g. and hydrants shall include the following specific design criteria: The main valve closure shall be of the compression type, opening against the pressure and closing with the pressure. Traffic feature to be designed for easy 360 rotation of nozzle section during field installation. There shall be a sealed lubrication chamber with triple O-rings to seal operating threads from the waterway and accomodate an anti-friction thrust washer. The main valve opening shall not be less than 5¼" and be designed so that removal of all working parts can be accomplished without excavating. The bronze seat shall be threaded into mating threads of bronze for easy field repair. The draining system of the hydrant shall be bronze and be positively activated by the main operating rod. Hydrant drains shall close completely after no more than three turns of the operating nut. There shall be a minimum of three internal ports and four drain port outlets to the exterior of the hydrant. Drain shutoff to be by direct compression closure. Friction loss not to exceed 3.5 p.s.i.g. at 1000 gpm through 4½" pumper nozzle. Hydrants shall be American Flow Control s American-Darling B-62-B-5. bury dir. to Open hydrant w/drain hydrant l/drain 5' 0" OL 42691 1 WD 42691 1 ND 5' 6" OL 42691 2 WD 42691 2 ND 6' 0" OL 42691 3 WD 42691 3 ND 6' 6" OL 42691 4 WD 42691 4 ND 7' 0" OL 42691 5 WD 42691 5 ND 7' 6" OL 42691 6 WD 42691 6 ND 5' 0" OR 42696 WD 42696 ND 5' 6" OR 42697 WD 42697 ND 6' 0" OR 42697 1 WD 42697 1 ND 6' 6" OR 42697 2 WD 42697 2 ND 7' 0" OR 42697 3 WD 42697 3 ND 7' 6" OR 42697 4 WD 42697 4 ND WD With drains open ND With drains plugged * Hydrants listed are with 1½" Pentagon operating nut and 2 2½" Hose nozzles and 1 4½" Pumper nozzle all NST (national standard). NOTE: Demonstration trailer and training tapes are available. Please call your local Team EJP sales office for more information. D-10 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-11 American- Darling B-62-B-5 D 5¼" B-62-B Fire Hydrant Construction www.ejprescott.com D-11
D-12 American- Darling B-62-B-5 5¼" B-62-B Fire Parts Illustration D-12 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-13 American- Darling B-62-B-5 D How to Order Parts The part shown should be prefixed by the following s to designate the size and model of hydrant: 54 for 5¼" valve opening 62 for Model B-62-B EXAMPLE: 5¼" Operating Nut - 54-62-1 notes: 1. Size and shape of nut on operating nut and cap, threading on nozzles and caps, and the direction of opening made to specifications. 2. Cap chains are not furnished unless specified. 3. All gray iron is ASTM A126 class B. 4. Bolts and nuts are rustproofed steel ASTM 5. A307 in accordance with AWWA C502. 6. Working pressure 200 p.s.i.g., test pressure 400 p.s.i.g. 7. Hydrant conforms to AWWA Standard C502. 8. Upper barrel can be rotated 360. 9. Factory Mutual Approved and Underwriters Laboratories Listed at 200 p.s.i.g. in allowable configurations. 10. Bronze in contact with water contains less than 16 percent zinc. 11. 6-inch mechanical joint base is ductile iron. 12. Nominal turns to open is 22. part no. qty description material 62-1 1 Operating Nut OR Bronze 42700 07 62-1 1 Operating Nut OL Bronze 42700 06 62-2-1 1 Cover O-ring Buna-N 42700 11 62-2-2 2 Housing O-ring Buna-N 42700 12 62-4-4 1 Thrust Washer Nylatron 42700 13 62-5-3 1 Pipe Plug Stainless Steel 42700 14 62-7-7 1 Weather Cover OR Gray Iron 42700 151 62-7-7 1 Weather Cover OL Gray Iron 42700 152 62-9 1 Housing Cover Gray Iron 42700 161 62-11-2 4 Housing Cover Cap Screw See Note 4 42700 16 62-13 1 Housing Cover Gasket Fiber 42700 09 62-14 1 Housing Gasket Composition Rubber 42700 08 62-15 1 Housing Ductile Iron 42700 17 62-16 6 Housing Bolt and Nut See Note 4 42700 18 62-18-60 1 Upper Barrel w/pumper Ductile Iron 42700 191 62-19-SR 1 Lower Barrel Ductile Iron 42700 20 62-20-60 2 Hose Nozzle Bronze (See Note 10) 42700 215 62-20-61 2 Hose Nozzle O-ring Buna-N 42701 2 62-20-62 2 Hose Nozzle Retainer Ductile Iron 42700 216 62-20-63 2 Hose Nozzle Washer Teflon 42700 217 62-21 2 Hose Cap Gray Iron 42700 22 62-22 2 Hose Cap Gasket Rubber 42700 23 62-23-1 1 Per Nozzle Hose Cap Chain Steel 42700 24 62-23-2 1 Per Nozzle Cap Chain S-Hook Steel 42700 241 62-25-60 1 or 0 Pumper Nozzle Bronze (See Note 10) 42700 261 62-25-61 1 Per Nozzle Pumper Nozzle O-ring Buna-N 42700 271 62-25-62 1 Per Nozzle Pumper Nozzle Retainer Ductile Iron 42700 272 62-25-63 1 Per Nozzle Pumper Nozzle Washer Teflon 42700 273 62-26 1 Per Nozzle Pumper Cap Gray Iron 42700 28 62-27 1 Per Nozzle Pumper Cap Gasket Rubber 42700 29 62-29-14 2 Snap Ring Steel 42700 30 62-29-15 1 Breakable Flange Gray Iron 42700 31 62-29-16 1 Base Flange Ductile Iron 42700 32 62-29-30 1 Rod Coupling Breakable Gray Iron 42700 04 62-29-31 2 Rod Cplg. and Clip Pins Stainless/Bronze 42700 05 62-30-03 1 Hydrant Spring Spring Steel 42700 33 62-30-04 1 Spring Plate Steel 42700 34 62-30-06 1 Travel Stop Nut OL Bronze (See Note 10) 42700 03 62-30-06 1 Travel Stop Nut OR Bronze (See Note 10) 42700 10 62-30-07 1 Spring Plate Pin Steel 42700 35 62-30-11 1 Upper Hydrant Rod OR Steel 42700 361 62-30-11 1 Upper Hydrant Rod OL Steel 42700 362 62-30-12 1 Lower Hydrant Rod Steel 42700 37 62-31 1 Drain Lever Bronze (See Note 10) 42700 38 62-33 3 Drain Lever Washer Rubber 42700 39 62-34 3 Drain Lever Rivet Brass 42700 40 62-35-OR 1 Hydrant Seat Solid Bronze (See Note 10) 42700 41LD 62-35-OR 1 Hydrant Seat Draining Bronze (See Note 10) 42700 41WD 62-36-2 1 Seat O-ring-Outside Buna-N 42700 42 62-36-3 1 Seat O-ring-Inside Buna-N 42700 43 62-37-OR 1 Drain Ring Bronze (See Note 10) 42700 44 62-38 1 Drain Ring Gasket Composition Rubber 42700 45 62-38-1 1 Barrel Gasket Composition Rubber 42700 46 62-38-6 1 Base Gasket Composition Rubber 42700 47 62-39 8 Base SS Bolt and Nut Stainless Steel 42700 48 62-39-9 8 Barrel Bolt and Nut See Note 4 42700 49 62-40 1 Hydrant Valve Top Gray Iron 42700 50 62-41 1 Hydrant Valve Rubber 42700 01 62-42 1 Hydrant Valve Bottom Ductile Iron 42700 02 62-46-5 1 6 Mechanical Joint Base Ductile Iron 42700 51 62-144 1 Weather Shield Rubber 42700 52 62-147 1 Seat Wrench Cast Iron 42700 62 www.ejprescott.com D-13
D-14 American- Darling B-62-B-5 B-62-B Break Repair Kit B-62-B Traffic Model Top Extension Kit The B-62-B Break Repair Kit makes it a quick and simple job to repair a hydrant that has been damaged by traffic. This kit contains all the parts needed to replace those parts designed to break away upon impact from a vehicle. description B-62-B Hyd. Break Repair Kit (1985) 42716 B-62-B Hyd. Break Repair Kit (1986) 42715 B-62-B QF Hyd. Break Repair Kit 42717 The 5¼" B-62-B hydrant is extended at the barrel flange above the ground line, eliminating any need for excavation. The B-62-B Top Extension Kit includes all parts necessary to extend the hydrant. description 6" B-62-B Hydrant Top Extension 42698 12" B-62-B Hydrant Top Extension 42699 18" B-62-B Hydrant Top Extension 42699 3 24" B-62-B Hydrant Top Extension 42699 5 NOTES: Longer extension barrels are available by special order. Contact your local Team EJP sales office for price and availability. When extending hydrants, the existing breakable coupling must be moved to the top of the new extension barrel to maintain traffic feature. D-14 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-15 Clow Eddy F-2640 D Eddy F-2640 Features 2 1 3 4 5 6 7 Time Tested Performance same design and parts since 1875 Conforms Fully with AWWA C-502 Opens Easily and Quickly with Pressure Both Drain and Drainless Features are Standard NOTE: If you would like to learn more about the Clow Eddy F-2640 Hydrant please contact your local Team EJP sales office for more information or to schedule a demonstration. 1. Threaded Nozzles: Easy replacement locking pin to hold nozzle in place; O-Ring Seal 2. Rising Stem: Lets you know position of main valve Indicator Feature 3. Independent Drain: Allows plugging of drain without disassembly of hydrant 4. Break Flange Design: For traffic safety 5. Main Valve Closes Against Pressure: Eliminates valve seat damage reducing the slam hazards of water hammer 6. Main Valve Opens With Pressure: Water assists in opening the valve making operation easier, faster and positive 7. Stem Nut Below Ground Line: Maintains positive shut off of main valve after traffic damage Does not depend on water pressure Never needs lubrication Bronze to Bronze Connection NOTE: Epoxy coated shoe provided at no extra cost. www.ejprescott.com D-15
D-16 Clow Eddy F-2640 Ordering Information: Quantity of hydrants and accessories required Size of main valve opening: 4½" or 5¼" Size and of hose nozzles Size and of steamer nozzles With or without chains or nozzles Hose and pumper nozzle thread specifications Type of inlet connection Depth of trench or bury Direction of opening Size and shape of operating nut and cap nuts Specify with drain or without drain bury dir. to Open hydrant w/drain Hydrant L/Drain 5' 0" OL 42332 42333 5' 6" OL 42357 42354 6' 0" OL 42351 42352 6' 6" OL 42357 02 42390 7' 0" OL 42357 04 42357 05 7' 6" OL 42357 07 42357 08 5' 0" OR 42357 2 42357 3 5' 6" OR 42358 42358 1 6' 0" OR 42360 42360 7 6' 6" OR 42359 05 42359 7' 0" OR 42362 42361 7' 6" OR 42362 5 42362 7 Specifications: Eddy F-2640 Hydrant with Drain Hydrant shall be center stem type and in accordance with AWWA Standard C-502-85. Hydrant shall be compression type with the main valve opening with the water pressure and have a rising stem to positively indicate open or closed position. Hydrant shall be furnished with frangible break flange and break coupling at the groundline. Bronze stem threads shall be located below the main valve to eliminate necessity of lubrication and in case of damage to hydrant, main valve will remain mechanically closed. Hydrant shall have minimum valve opening of either 4½" or 5¼", and shoe inlet of 6". Hydrant shall be designed to permit removal of all working parts without special tools or wrenches. Hydrant shall have automatic drain, independent of main valve, to provide removal or adjustment without shutting off water and can be cleaned without digging. Hydrant shall be the Eddy Hydrant, manufactured by the Clow Valve Company. Eddy Top Extension Eddy Break Repair Kit Valve opening Hydrant w/drain hydrant no drain 5¼" 42377 1 42377 size & Length Hydrant w/drain hydrant no drain 5¼" x 6" 42364 NS 13 5¼" x 12" 42366 NS 13 5¼" x 18" 42371 NS 13 5¼" x 24" 42367 NS 13 D-16 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-17 Clow Eddy F-2640 D Eddy F-2640 Parts Part qty description material no. 1 1 Hold Down Bolt Stainless 42388 2 1 Operating Nut O.L. Cast Iron 42388 01 2 1 Operating Nut O.R. Cast Iron 42388 02 3 1 Packing Nut Bronze 42388 03 4 1 Packing Fiber 42388 04 5 1 Cover Cast Iron 42388 05 6 8 Cover Bolts & Nuts Steel 42388 06 7 1 Swivel Ring Cast Iron 42388 07 8 1 Nozzle Section Cast Iron 42381 9 ** Pumper Nozzle Bronze 42372 10 ** Nozzle Chain* Steel 42388 08 11 ** Pumper Nozzle Cap Cast Iron 42388 09 12 ** Pumper Cap Washer Rubber 42388 10 13 8 Flange Bolts & Nuts Steel 42376 3 14 3 Flange Gaskets Accopac 42388 11 15 ** Hose Nozzle O-Ring* Rubber 42388 12 15 1 Pumper Nozzle O-Ring* Rubber 42388 121 16 ** 2.5" Hose Nozzle Bronze 42373 17 ** 2.5" Hose Nozzle Cap Cast Iron 42388 13 18 ** 2.5" Hose Cap Washer Rubber 42373 1 19 1 Upper Stem Stl. & Bronze 42388 14 20 1 Standpipe Cast Iron 42388 15 21A 1 Valve Plate Cast Iron 42388 16 22A 2 O-Ring Rubber 42388 17 24 1 Valve Rubber Rubber 42378 25 1 Seat Ring Bronze 42388 18 26 1 Throttling Ring Bronze 42388 19 27A 2 Thrust Washer Teflon 42388 20 28A 1 Snap Ring Stainless 42388 21 29A 1 Lower Stem Mang. Bronze 42387 30 1 Stem Wedge Polycarbonate 42388 22 31 1 Stem Wedge Screw Bronze 42388 23 32 1 Lock Nut Bronze 42388 24 33 1 Drain Spool Bronze 42388 25 34 1 Drain Lever Bronze 42376 35 1 Lever Pin Bronze 42388 26 36 1 Clevis & Nut Bronze 42388 27 37 1 Drain Support Cast Iron 42388 28 38 1 Drain Rod Steel 42388 29 39 1 Drain Valve Backer Bronze 42388 30 40 1 Drain Valve Rubber Rubber 42388 31 41 1 Drain Cup Bronze 42388 32 42 1 Retaining Nut Bronze 42388 33 43 ** Bottom B & N Steel 42388 34 44 1 Bottom Gasket Accopac 42388 35 45 1 Bottom Cast Iron 42363 45A 1 Stem Nut Clip Stainless 42388 37 45B 1 Bottom Nut O.L. Bronze 42388 38 45B 1 Bottom Nut O.R. Bronze 42388 39 46 1 Stem Coupling Steel Tubing 42376 1 47 2 Stem Coupling Pin Stainless 42376 2 48 1 Middle Stem Steel 42388 36 * Not Shown ** Quantity As Required NOTE: When ordering hydrant parts please specify the direction of opening (open left or open right) and the valve opening size (4¼", 4½" or 5¼"). www.ejprescott.com D-17
D-18 Clow Medallion Fire Protection The Clow Medallion hydrant is designed and built to provide unsurpassed fire protection. Utilizing computer developed data, Clow engineers painstakingly sculpted interior surfaces to provide the smoothest possible waterway, resulting in the lowest possible loss of head through the hydrant. The result? More water to the nozzles faster. With the Clow Medallion, it s performance that counts. Maintenance While providing fire protection is a hydrant s primary function, ease of maintenance and repair are valid concerns of maintenance crews. Extraordinary steps were taken to insure that the Clow Medallion can be routinely serviced and repaired easily. All working parts are readily accessible from the top of the hydrant. 5-Year Limited Warranty The Medallion equals or exceeds the requirements of the American Water Works Association (AWWA). Also it has been listed by the Underwriters Laboratory (UL) and is approved by Factory Mutual (FM). Structurally and operationally this is clearly a superior Fire Hydrant. It s easy to see why it carries a full 5-year limited warranty on materials and workmanship. Specifications: Fire Hydrant shall be manufactured in accordance with AWWA C-502, be listed by Underwriters Laboratories, Inc. and have Factory Mutual Research approval. Fire Hydrant shall be designed for 250 psi working pressure and tested to 500 psi hydrostatic pressure. Fire Hydrant shall be dry-top center stem construction having an O -Ring sealed lubrication reservoir. Fire Hydrant shall be backed by manufacturer s 5-year limited warranty. Fire Hydrant shall be manufactured with operating nut and thrust nut made of bronze, with bearings located both above and below the thrust collar and with operating nut protected by a cast iron weather shield. Fire Hydrant shall be manufactured with nozzles mechanically locked into the barrel and having O - Ring pressure seals. Fire Hydrant shall be a Traffic Model, complete with safety flanges and steel stem coupling. Nozzle section must rotate 360 degrees. Fire Hydrant shall be manufactured with a main valve seat ring of bronze threaded into a bronze drain ring. A 360 degree drain channel shall have a minimum of two drain outlets. Fire Hydrant shall have a bronze upper valve plate and two urethane rubber facings that activate the drain ports. Fire Hydrant shall be manufactured with a lower valve plate that bottoms out in the shoe for maximum opening. Fire Hydrant shall be manufactured with a minimum main valve opening of 4½" or 5¼". Fire Hydrant shall be the Clow Medallion as manufactured by the Clow Valve Company or approved equal. D-18 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-19 Clow Medallion D Clow Medallion Features 1. Moisture Protection: Durable cast iron weather cap combines with one piece bronze operating nut and "O"-rings to ensure reliable corrosion-free operation under all weather conditions. 1 8 2. Lubrication Reservoir: "O"-ring seals keep the oil in and water out. Reservoir may be filled easily without disassembly. 3. Computer Designed Contours: All interior components were individually designed to provide the lowest possible head-loss, which means more water, faster. 2 9 4. Safety Stem Coupling System: Breakaway parts shear cleanly below the top of the barrel, preventing nozzle section damage or opening of the main valve. 5. Bronze to Bronze: Bronze seat ring threads into bronze drain ring for corrosion-free protection. 3 10 6. Bronze Upper Valve Plate: Computer contoured shape means less turbulence smoother flow. 11 7. Compression Seating: High durometer rubber valve closes with the water pressure for a positive seal. 8. Anti-Friction: Thrust bearings above and below the bronze thrust collar provide low-torque operation even at 250 psi working pressure. 4 12 9. Bonnet Seals: Standard "O"-rings secure mating flanges and sealing throughout the Medallion. All "O"- rings are dependable and easy to replace. 10. Bronze Nozzles: Corrosion-resistant, field-replaceable bronze nozzles have "O"-ring seals for watertight connections. 11. Nuts & Bolts: Are stainless steel for long life. 5 13 12. Drain Valve: Rubber valve facing provides tight, long life seal. Bronze seat ring has 360 drain channel. Double ports flush with each use. 13. Ductile Iron Hydrant Shoe: Epoxy coated inside and out and shaped for low turbulence and maximum flow, the shoe is offered in a variety of end connections. 6 14. Lower Valve Plate: Bottoms out in the bottom of the strengthened shoe. Prevents valve from falling below seat ring. 15. Pads: Pads on hydrant shoe give large surface areas for standing and blocking hydrant. 7 15 14 www.ejprescott.com D-19
D-20 Clow Medallion Ordering Information: Quantity of hydrants, accessories and maintenance kits required Size of main valve opening: 4½" or 5¼" Size and of hose nozzles Size and of steamer nozzles Hose and pumper nozzle thread specifications Type of inlet connection Depth of trench or bury Direction of opening Size and shape of operating nut, weather shield and cap nuts Color desired Town or municipality where hydrants will be installed, if possible bury dir. to Open hydrant w/drain hydrant l/drain 4' 6" OL 42795 42795 ND 5' 0" OL 42800 42800 ND 5' 6" OL 42805 42805 ND 6' 0" OL 42810 42810 ND 6' 6" OL 42815 42815 ND 7' 0" OL 42820 42820 ND 4' 6" OR 42825 42825 ND 5' 0" OR 42830 42830 ND 5' 6" OR 42835 42835 ND 6' 0" OR 42840 42840 ND 6' 6" OR 42845 42845 ND 7' 0" OR 42850 42850 ND Medallion Kits description 5¼" Medallion Main Valve Repair Kit 42911 5¼" Medallion Safety Repair Kit 42912 Medallion Top Extensions description 5¼" x 6" Medallion Hyd. Extension 42913 5¼" x 12" Medallion Hyd. Extension 42914 5¼" x 18" Medallion Hyd. Extension 42915 5¼" x 24" Medallion Hyd. Extension 42916 D-20 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-21 Clow Medallion D 58 29 29 33 46 47 49 46 51 56 51 25 26 27 28 31 30 32 34 39 48 50 35 52 53 54 53 57 40 36 41 37 42 38 43 44 45 15 8 9 12 14 16 17 18 19 20 21 22 24 1 2 3 2 4 5 6 7 10 11 13 Clow Medallion Parts ref. no. qty description material 1 1 Operating Nut O-Ring NBR 42917 01 2 2 Operating Nut Thrust Bearing Delrin 42917 02 3 1 Operating Nut O.R. Bronze 42917 03 3 1 Operating Nut O.L. Bronze 42917 04 4 1 Upper Stem Jam Nut SS 42917 05 5 1 Upper Stem Sleeve Bronze 42917 06 6 1 Upper Stem Sleeve O-Ring NBR 42917 07 7 1 Upper Stem O.R. CRS 42917 08 7 1 Upper Stem O.L. CRS 42917 09 8 1 Upper Stem Pin SS 42917 10 9 2 Safety Coupling Cotter Pins SS 42917 11 10 1 Safety Stem Coupling ST 42917 12 11 2 Safety Coupling Pins SS 42917 13 12 1 Lower Stem CRS 42917 14 13 1 Lower Stem Pin SS 42917 15 14 1 Upper Valve Plate O-Ring NBR 42917 16 15 4 Drain Valve Facing Screw SS 42917 17 16 2 Drain Valve Facing UR 42917 18 17 1 Upper Valve Plate Bronze 42917 19 18 1 Seat Ring Upper O-Ring NBR 42917 20 19 1 Seat Ring Bronze 42917 21 20 1 Seat Ring Lower O-Ring NBR 42917 22 21 1 Main Valve Rubber UR 42917 23 22 1 Lower Valve Plate Lockwasher SS 42917 24 24 1 Lower Valve Plate Bronze 42917 25 25 1 Weather Cap Hold Down Screw ZPS 42917 26 26 1 Weather Cap CI 42917 27 27 1 Thrust Nut Bronze 42917 28 28 1 Thrust Nut O-Ring NBR 42917 29 29 4 Bonnet Bolts & Nuts ZPS 42917 30 30 1 Bonnet CI 42917 31 31 2 Stem O-Rings NBR 42917 32 32 1 Bonnet O-Ring NBR 42917 33 33 1 Nozzle Section CI 42917 34 34 1 Pumper Nozzle Lock SS 42917 35 35 1 Pumper Nozzle O-Ring NBR 42917 36 36 1 Pumper Nozzle Bronze 42917 37 37 1 Pumper Nozzle Gasket Rubber 42917 38 38 1 Pumper Nozzle Cap CI 42917 39 39 2 Hose Nozzle Lock SS 42917 40 40 2 Hose Nozzle O-Ring NBR 42917 41 41 2 Hose Nozzle Bronze 42917 42 42 2 Hose Nozzle Gasket Rubber 42917 43 43 2 Hose Nozzle Cap CI 42917 44 44 1 Chain ZPS 42917 45 45 1 Trench Depth Tag & S-Hook AZPS 42917 46 46 8 Safety Flange Bolts & Nuts ZPS 42917 47 47 2 Safety Flange O-Ring NBR 42917 48 48 1 Barrel Upper Flange CI 42917 49 49 2 Safety Flange CI 42917 50 50 1 Barrel DI 42917 51 51 8 Shoe Bolts & Nuts SS 42917 52 52 1 Barrel Lower Flange CI 42917 53 53 2 Drain Ring O-Rings NBR 42917 54 54 1 Drain Ring Bronze 42917 55 56 4 Locking Spacer Steel 42917 56 57 1 Shoe CI 42917 57 58 1 Thrust Nut Set Screw SS 42917 58 Material Legend: CI...Cast Iron DI...Ductile Iron NBR...Nirtrile Butadiene Rubber SS...Stainless Steel Brz...Bronze CRS...Corrosion Resistant Steel Rbr...Rubber ST...Steel Tubing UR... Urethane Rubber Stl...Steel AZPS...Aluminum & Zinc Plated Steel ZPS...Zinc Plated Steel www.ejprescott.com D-21
D-22 Post Hydrant The Eclipse #2 Post Hydrant Features: Comes with either one or two nozzles of the size you 1. select. 1 2 2. Interior parts can be replaced without disturbing any connections by unbolting the top cap and withdrawing the inside working parts. 3. Available in any depth of bury. 4. All hydrants come with ductile iron barrels for strength and corrosion resistance for longer life. 5. Has 2 3 16" valve opening. 6. Inlet can be 2", 2½" or 3" iron pipe thread. Also available with 2" or 3" mechanical joint inlet. 3 7. Self-draining feature prevents barrel freezing. 4 Handwheel Option Tamper Proof Option 5 6 #2 Post Hydrants have many features comparable to full size AWWA hydrants 7 NOTE: Post Hydrants are available in a wide variety of sizes and styles. Post Hydrants are non-stock and are ordered as needed. Please call your local Team EJP sales office for more information or assistance in ordering. D-22 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-23 2" Blow Off Hydrant D The MainGuard Model #77 2" Blow Off Hydrant 3 1 Features: 1. 2½" NST Nozzle Also available in smaller sizes. 2. Traffic Break Away The MainGuard is designed to break easily at ground level. 3. Security A locking cover prevents water theft and protects MainGuard from the elements. 4. Easy Repair Just remove two bolts and take the inner workings out for easy repair and replacement. 5. Brass Working Parts All the moving parts are enclosed and made from high quality brass for greater durability and wear. 6. Full Draining Capabilities The MainGuard drains to prevent freezing after flushing. 7. 2" Female Iron Pipe Inlet 2 4 5 7 description bury 6 #77 MainGuard Blow-Off Hyd. 6' 0" 42646 #77 MainGuard Blow-Off Hyd. 5' 6" 42647 The MainGuard Model #78 Blow Off Hydrant The Model #78 has the same features as the Model #77 Blow Off hydrant except that it is designed for underground installations. The Model #78 can be placed in a meter box pit for easy access. NOTE: MainGuard Blow Off hydrants are available on a custom order basis only. Please call your local Team EJP sales office for more information or assistance in ordering. www.ejprescott.com D-23
D-24 Sampling Station Eclipse No. 88 Sampling Station 1 Features: 1. All interior parts can be replaced without disturbing connections by unbolting the top cap and withdrawing the inside working parts. 2. ¾" hose connection or unthreaded brass nozzle to allow for easy flaming for disinfection. 3. Aluminum weathershield with handy interior shelving for supplies and storage. 2 4. Vent tube with open/close valve. 5. Brass interior pipe isolates water flow and maintains consistency of brass interior parts, insuring maximum 4 6. 7. sample quality. Galvanized riser pipe for exterior protection. Brass valve body with ¾" FIP inlet. 3 6 Specifications: Sampling Stations shall be (specify) bury, with a ¾" FIP inlet, and a ¾" hose or unthreaded nozzle. All stations shall be enclosed in a lockable, non-removable, aluminum-cast housing. When opened, the station shall require no key for operation, and the water will flow in an all-brass waterway. All working parts will also be of brass and be removable from above ground with no digging. A copper vent tube will enable each station to be pumped free of standing water to prevent freezing and to minimize bacteria growth. The exterior piping will be galvanized. Sampling Stations shall be as manufactured by Kupferle Foundry, St. Louis, MO. NOTE: Sampling Stations are non-stock items. Please call your local Team EJP sales office to order or for more information. 5 ¼" Vent Tube used to pump water from barrel Standard utility bilge pump attaches to vent tube to remove water from waterway, insuring a clean sample in the future, and preventing freezing. 7 D-24 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-25 Hydrant Markers & Accessories D Hydrant Markers & Tags markers: Double dipped in Safety Orange color paint 2 reflective, weatherproof stickers are supplied so hydrants can be easily located at night Standard rods are ½" with ½ loop for easy installation Large 4½" round flag reduces chance of injury Individually wrapped and packed 10 to a bundle Galvanized Spring Flags W/Reflective Bands Close-up of Spring with washer Tags: Galvanized attaching cable with duplex clips Unbreakable tempered virgin nylon Numbered or lettered both sides; 3 characters standard; 4 characters available for an additional charge 8 vivid color combinations Crimping tool available description Hydrant Tag Crimping Tool 48" Hydrant Marker 3 8" Galvanized 41000 48" Hydrant Marker ½" Rebar 41001 52" Hydrant Marker 3 8" Galvanized 41004 Hydrant Tag w/cable & Clip 41003 Hydrant Tag Crimping Tool 63970 Spring-loaded Hydrant Markers are made of one piece galvanized spring steel for corrosion resistance. The mounting bracket is part of the spring; a washer is supplied. Four 6" reflective weatherproof bands are applied (two red and two white) to the top section of the marker for superior visibility. description 4' Galv. Spring Flag w/reflective Bands 41002 5' Galv. Spring Flag w/reflective Bands 41002 1 4' Galv. Spring Flag w/bands 4" x 5" Flag 40999 4" x 5" Replacement Flag 40999 1 Shown mounted on 3 8" rod Orange Fire Hydt. Sign 7" O.D. 3.25" I.D. 05634 1A Universal Flag Kit (Lexan) 4½" Disc w/center Mounted U-Clip & SS Set Screw Fits ¼" to ½" Shaft 05819A www.ejprescott.com D-25
D-26 Hydrant & Waterworks Tools Hydrant Setter* The hydrant setter greatly eases the installation of hydrants which can weight as much as a half ton. The lifting rings, which are held in proper alignment by the spreader bar, fit over the 2½" hose nozzles and are locked in place by the hose nozzle caps. Adjustable Hydrant Wrench This hydrant wrench is adjustable to fit up to 1¾" pentagon operating nuts and pumper or steamer caps. The handle is knurled for a better grip. description Adjustable Hydrant Wrench - Zinc Coated 63279 description Hydrant Setter with Spreader Bar 63281 * Hydrant Setters are pull-tested, certified and tagged with capacity. D-26 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
D-27 Hydrant Storz Connections D Integral Hydrant Storz The integral hydrant storz nozzle is provided on new hydrants. A storz spanner wrench is required for cap removal. The storz meets or exceeds the requirements of AWWA C502 regarding material and pressure testing. The storz shall have a brass metal face and hard anodized aluminum storz ramps and lugs. The aluminum finish shall be hard coat anodized to Mil-A-8625, Type 3, dark gray. The storz shall be made of forged or extruded 6061-T6 aluminum. The blind cap shall have hard anodized aluminum storz ramps and lugs, made of forged or extruded 6061- T6 aluminum. The cap shall be equipped with a suction seal. The cap shall be connected to the hydrant with a 0.125" vinyl coated aircraft cable. Once installed, the integral hydrant storz with cap extends less than 2" from the hydrant nozzle. Permanent Hydrant Storz The permanent hydrant storz threads onto the male nozzle and is secured permanently to the hydrant. A storz spanner wrench is required for cap removal. The storz adapter shall have a hard anodized aluminum metal face seal and hard anodized aluminum storz ramps and lugs. The adapter finish shall be hard coat anodized to Mil-A-8625, Type 3, dark gray. The adapter shall be made of forged or extruded 6061-T- aluminum and secured to the nozzle by (2) stainless steel screws, inserted 180 degrees apart. The female adapter shall contain a flat rubber gasket which seals against the male hydrant nozzle. The blind cap shall have hard anodized aluminum storz ramps and lugs, made of forged or extruded T6061-T6 aluminum. The cap shall be equipped with a suction seal. The cap shall be connected to the adapter or hydrant with a 0.125" vinyl coated aircraft cable. Once installed, the permanent hydrant adapter with cap extends less that 3" from the hydrant nozzle. NOTE: For more information please contact your local EJP sales representative. www.ejprescott.com D-27
D-28 Captivater Hydrant Lock The Captivater Locking Fire Hydrant Cap The Captivater prevents unauthorized hydrant use, eliminates water theft and waste, reduces hydrant vandalism and lowers operation costs. Its universal design fits EVERY hydrant from EVERY manufacturer, regardless of year or model. Features: The Captivater is the perfect Homeland Security solution: The Captivater fits any make, model or year of hydrant in minutes without modification. Provides a safe and easy method to secure fire hydrants. Easily installed in minutes without special tools. Sealed for protection from the elements, the Captivater withstands weather and long-term use as well as or better than original caps. All Captivater wrenches are serial ed, allowing hydrant access to be controlled. The Captivater s appearance is the same as a standard hydrant cap. What Does This Mean? Your hydrants are secured from unauthorized use, so children and vandals (or people with more sinister plans) cannot gain access to your water system. Benefits: The Captivater solves security and safety issues. It eliminates water theft from hydrants. It ensures the availability of water-dependent services. Reduces operation costs; revenue loss from open hydrants will be a thing of the past. The Captivater helps conserve your water supply and by saving water, you save money! description Captivater Hydrant Lock Cap (Pumper 41020 Captivater Hydrant Lock Cap (Hose) 41020 1 NOTE: For more information please contact your local EJP sales representative. Captivater Hydrant Lock Wrench description Captivater Hydrant Lock Wrench* 41020 2 * To insure security all wrenches are shipped direct to the customer from the factory. D-28 Phone: 800-EJP-24HR (357-2447) Fax: 207-582-5637
Waterous Classic Pacer THE RIGHT WAY The Waterous Classic Pacer by AMERICAN Flow Control merges a classic look with all the traditional features of the standard Pacer design. Classic look with the standard contemporary Pacer design features Complete parts interchangeability with the contemporary Pacer Ductile iron nozzle section, standpipes and base Available through your local AMERICAN Flow Control distributor Two-part catalyzed epoxy primer and polyurethane coating system above grade 250 psig rated working pressure Shown with optional Storz pumper nozzle AMERICAN Flow Control P.O. Box 2727 Birmingham, AL 35202-2727 Phone: 1-800-326-8051 Fax: 1-800-610-3569 E-mail: afcsales@american-usa.com Waterous Company 125 Hardman Avenue South South St. Paul, MN 55075-1191 Phone: 1-888-266-3686 Fax: 1-800-601-2809 E-mail: afcsales@american-usa.com Version 06 15 12