ENGINEERING DATA Industrial Hydraulics Variable Volume Vane Pumps Models SV-20 & SV-25 Flange & Subplate Mounted SYMBOL Quick Reference Chart GPM @ MAXIMUM PRESSURE THEORETICAL INPUT HP MODEL 100 PSI & PRESSURE MAXIMUM COMPENSATING DISPLACEMENT @MAX PSI 1800 RPM (PSI) RPM RANGE (PSI) RANGE (PSI) & 1800 RPM Standard SV-20 15 2000 1800 375-2000 1.9 20 Standard SV-25 20 1000 1800 300-1000 2.56 20.3 Low Pressure SV-20 15 750 1800 175-750 1.9 7.25 Low Pressure SV-25 20 750 1800 175-750 2.56 9.75 STANDARD PUMP The SV pump is a pressure compensated vane pump and is available in four basic displacements; one, two, four and eight cubic inches. This bulletin covers the Model SV-20 (two cubic inch displacement) and variations of it all of which are dimensionally the same. The SV-25 is a modified SV-20 which uses a different ring to allow the ring to shift further and increase the displacement. By increasing the ring stroke, the vanes extend further and requires the maximum pressure rating to be reduced. Increasing the flow of the basic pump allows the design engineer to reduce circuit costs by using a smaller pump instead of selecting the next larger size provided the reduced pressure rating is adequate. LOW PRESSURE PUMP On some applications, such as grinders, the pump must compensate at very low pressures which are not within the normal compensating range of the standard pump. By making internal modifications to the standard pump, the compensating range can be reduced to create a low pressure pump for this kind of application. PUMP MODEL SERVICE BULLETIN Standard SV-20 & SV-25 9 535 233 240 Low Pressure SV-25 & SV-25 9 535 233 241 For repair parts, refer to the service bulletin listed in the table. Product Literature Disclaimer: Specifications and/or dimensions are subject to change without prior notice. Please consult factory.
2 Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 Bosch Rexroth Standard Pump PRESSURE RATING SV-20 2000 psi (138 bar) SV-25 1000 psi (69 bar) PRESSURE COMPENSATING RANGE SV-20 375-2000 psi (26-138 bar) two stage compensator 300-2000 psi (23-138 bar) single stage compensator SV-25 300-1000 psi (21-69 bar) two stage compensator 280-1000 psi (19-69 bar) single stage compensator FLOW @ 1800 RPM SV-20 15 gpm (56.8 l/min) @ 1900 psi SV-25 20.25 gpm (75.7 l/min) @ 900 psi THEORETICAL DISPLACEMENT SV-20 2 in 3 /rev (32.8 ml/rev) SV-25 2.6 in 3 /rev (42.6 ml/rev) MAXIMUM INLET VACUUM AT SEA LEVEL 6 in. Hg (152 mm Hg) 3 in. Hg (76mm HG) with fluids containing water MAXIMUM CASE PRESSURE 10 psi (0.7 bar) Case drain line should be full intended size (not reduced down). Case pressure spikes can be minimized by using as straight and direct path to tank as possible. Other drain lines should not be connected to the pump drain line. Always terminate the drain line below the fluid level in the reservoir. Failure to do so will result in loss of pump prime approximately 30 minutes after it is shut down and possible introduction of air into the circuit. Case drain line should be routed to the opposite side of the baffle in relation to the suction line. CASE DRAIN FLOW The values listed below are the average flows which occur only when the pump is compensating. When the pump is not compensating, the values are much lower. 100 in 3 /min (1.6 l/min) @ 1000 psi (69 bar) 150 in 3 /min (2.5 l/min) @ 1500 psi (103 bar) 200 in 3 /min (3.3 l/min) @ 2000 psi (138 bar) FILTRATION A 10 micrometer return line filter is recommended for increased pump life. If a suction strainer is used, it should not be finer than 100 mesh (149 micrometer) when using petroleum fluids. The higher specific gravity of fire resistant fluids and the higher vapor pressure of water containing fluids will aggravate the pump inlet conditions. If a suction strainer is used with these fluids, the mesh must be coarser (60 mesh or 238 micrometer) than what is used with petroleum oil of the surface area increased to reduce the pressure drop. Bosch Rexroth does not recommend the use of inlet suction strainers. OVERHUNG LOAD Radial and axial forces on the shaft are not recommended. Pump and prime mover should be mounted with shafts inline (coaxial) and connected with a flexible coupling. Consult factory Applications department for applications with overhung load. MAXIMUM ADDITIONAL HP ON THRU SHAFT 20 HP (15 Kw) @ 1800 rpm 13.25 Hp (10 Kw) @ 1200 rpm FLUID RECOMMENDATIONS A premium quality hydraulic oil with zinc complex anti-wear additives is highly recommended. Refer to Bosch Rexroth Group publication 9 535 233 456, Petroleum Hydraulic Fluids for a list of fluids which meet or exceed the Bosch Rexroth lubrication requirements. Optimum Viscosity at Operating Temperature Minimum Operating Viscosity Maximum Operating Viscosity Maximum Start-up Viscosity 150-250 SUS (32-54 cst) 100 SUS (21 cst) 1000 SUS (215 cst) 4000 SUS (864 cst) To compensate for the reduced lubrication values of even the premium quality water containing fluids (glycols and water-in-oil emulsions), it is necessary to limit system pressure to the values listed in the table below for an equivalent life. DRIVE SPEED RANGE 750-1800 rpm (Consult factory Applications department for higher speeds.) Water Glycol Water-in-Oil Emulsion MOUNTING Available in the following: Subplate SAE 2-bolt Flange, side or rear ported (SAE straight thread of 4- bolt Flange Connection.) ROTATION Rotation is always determined when viewing the shaft end. Rotational arrows are cast into the body of all pumps. Right hand rotation is standard. Left hand rotation pumps are no longer available. SEALS Viton seals are standard. Buna seals are no longer available. Maximum Pressure Maximum RPM 1500 psi 1000psi 1800 rpm 1200 rpm Refer to Bosch Rexroth Group publication 9 535 233 457, Fire Resistant Fluids, for further details on fluid selection. Fluid suppliers should be consulted regarding proper fluid maintenance when using fire resistant fluids containing water. TEMPERATURE The temperature of the fluid in the reservoir should not exceed 130 F (54 C). The pump will operate with fluid at higher temperatures provided the viscosity is within the recommended range. under no circumstances should the oil temperature exceed 160 F (71 C). When using fire resistant fluids containing water, the fluid temperature should not exceed 120 F (49 C) to prevent an excessive rate of water evaporation.
Bosch Rexroth Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 3 SCREW VOLUME CONTROL The screw volume control is an adjustable stop which is used to reduce the maximum pump flow and is optional. Turning clockwise will reduce the flow in direct proportion to the displacement of the adjusting screw. During initial start-up, the flow setting should be at least 50% of the maximum pump flow. SV-20 1 /4 turn (90 ) clockwise will reduce the flow approximately 2.2 gpm (8.3 l/min) when the pump is driven at 1800 rpm. SV-25 1 /4 turn (90 ) clockwise will reduce the flow approximately 2.9 gpm (11 l/min) when the pump is driven at 1800 rpm. When a volume control is used to reduce the maximum flow of the pump, the horsepower required to drive the pump is also reduced. To determine the input HP, use the following formula: Input gpm x psi = + Deadhead HP at the compensator setting HP 1714 MOUNTING POSITION Unrestricted. Caution must be exercised with vertical mounting to prevent the weight or end thrust of the prime mover from being applied to the pump shaft. SHAFT ALIGNMENT Shaft alignment should be within 0.003" total indicator reading. If the shafts are not properly aligned, increased mechanical noise from the unit will result. START-UP To insure priming on initial start-up, air in the pump and inlet must be allowed to escape. If the pump outlet is normally blocked, it must be temporarily vented. This can be accomplished by opening the valve, temporarily cracking a fitting, or installing an air bleed valve. CONTROL OPTIONS Many energy saving controls are available in addition to the standard two-stage pressure compensator. Refer to Bosch Rexroth publication 9 535 233 092 for performance and dimensional data. COMBINATION MOUNTING To simplify multi-pump circuits, adapter kits are available to mount additional pumps in combination on the rear cover of the flange mounted (side ported) pumps. Refer to Bosch Rexroth publication 9 535 233 094 for horsepower limitations, adapters available, dimensional data and How-To-Order. WEIGHT (Approximate) Subplate Mounted Pump...................65 lbs. (29.5 Kg) Flange Mounted Pump.....................70 lbs. (31.8 Kg) Add for Screw Volume Control.................1 lb. (0.5 Kg) Add for Thru Shaft............................1lb. (0.5 Kg) Low Pressure Pump NOTE: All of the specifications for the standard pump also pertain to the low pressure pump except those listed below. PRESSURE RATING SV-20 750 psi (52 bar) SV-25 750 psi (52 bar) PRESSURE COMPENSATING RANGE SV-20 175-750 psi (12-52 bar) SV-25 175-750 psi (12-52 bar) FLOW @ 1800 RPM SV-20 15 gpm (56.8 l/min) @ 650 psi (45 bar) SV-25 20 gpm (75.7 l/min) @ 650 psi (45 bar) CASE DRAIN FLOW 210 in 3 /min (3.4 l/min) is the average flow which will occur only when the pump is compensating at 750 psi (52 bar). When the pump is not compensating, the values are much lower. ROTATION Right hand only. Clockwise when viewing shaft end. SEALS Viton seals are standard. SCREW VOLUME CONTROL The screw volume control is standard.
4 Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 Bosch Rexroth Performance Characteristics Standard Pump
Bosch Rexroth Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 5 Performance Characteristics Low Pressure Pump
6 Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 Bosch Rexroth Dimensional Data RH Subplate Mounted
Bosch Rexroth Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 7 Dimensional Data LH Subplate Mounted (No longer available)
8 Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 Bosch Rexroth Dimensional Data RH Flange Mounted, Side Ported
Bosch Rexroth Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 9 Dimensional Data RH Flange Mounted, Rear Ported
10 Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 Bosch Rexroth Dimensional Data LH Flange Mounted, Side Ported (No longer available)
Bosch Rexroth Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 11 Dimensional Data LH Flange Mounted, Rear Ported (No longer available)
12 Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 Bosch Rexroth Dimensional Data Foot Bracket, (PSV-20-70B) Bolt kit B-90 is included to mount the pump to the foot bracket. Consists of 2 each 1 /2-13 x 1 1 /4 hex head screw. The center line height of the shaft of an electric motor can be determined by dividing the first two numbers of the motor frame size by four. INCHES (MILLIMETERS) NOTE: UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL. Dimensional Data Subplate, (PSV-20-20S-10) The height of the pump shaft center line is 6.25 inches (158.8 mm) when the pump is mounted to the subplate. When subplate is not used, a machined pad as shown by clear area must be provided for mounting. Pad must be flat within 0.0003 in/in with a surface finish of 63 RMS. Bolt kit B-16 is included to mount the pump to the subplate. Consists of 4 each 7 /16-14 x 1 1 /4 socket head cap screws. INCHES (MILLIMETERS) NOTE: UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL.
Bosch Rexroth Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 13 How to Order Standard Pump CONTROL OPTIONS N No Volume Control S Screw Volume Control CONTROL OPTIONS P Standard Pressure Compensator *S Solenoid Two-Pressure (Normally Low, Energize for High Pressure) *H Solenoid Two-Pressure (Normally High, Energize for Low Pressure) *V Solenoid Two-Pressure (Normally Vented, Energize for High Pressure) J Hydraulic Two-Pressure (Normally Low, Energize for High Pressure) L Load Sensing T Torque Limiting K Single Stage Compensator *Indicate the desired solenoid voltage and frequency at the end of the pump code. To order the lock for the compensator adjusting screw, specify LOCK at the end of the code. VOLUME CONTROL S Screw Volume Control CONTROL P Standard Pressure Compensator MOUNTING S Subplate A Flange, Side Ported (SAE Straight Thread) B Flange, Rear Ported (SAE Straight Thread) C Flange, Side Ported (4 Bolt Flanged Connections) R Flange, Rear Ported (4 Bolt Flanged Connections) MOUNTING S Subplate A Flange, Side Ported (SAE Straight Thread) B Flange, Rear Ported (SAE Straight Thread) C Flange, Side Ported (4 Bolt Flanged Connections) R Flange, Rear Ported (4 Bolt Flanged Connections) PSV PNSF 20HRM 56 SEALS F Viton Seals PSV PSSF 20DRM 56 SEALS F Viton Seals DESIGN DIGIT 56 (Subplate Mounted only) 66 (Flange Mounted only) SHAFT M Keyed Shaft Medium Length D Thru Shaft Medium Length (Subplate Mounted only) ROTATION (Viewing Shaft End) R Right Hand (Clockwise) L Left Hand (Counterclockwise) PRESSURE RATING H 2000 PSI E 1000 PSI (SV-25 only) FLOW 20 15 GPM @ 1800 RPM 25 20 GPM @ 1800 RPM SOLENOID VOLTAGE AVAILABLE 110/115 VAC 50/60 Hz (Dual frequency) 220/230 VAC 50/60 Hz (Dual frequency) 12 VDC 24 VDC For Solenoids with quick connect (Hirschmann type) consult factory How to Order Low Pressure Pump DESIGN DIGIT 56 (Subplate Mounted only) 66 (Flange Mounted only) SHAFT M Keyed Shaft Medium Length ROTATION (Viewing Shaft End) R Right Hand (Clockwise) PRESSURE RATING D 750 PSI FLOW 20 15 GPM @ 1800 RPM 25 20 GPM @ 1800 RPM
14 Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 Bosch Rexroth How to Order Subplate * Subplate Model Number PSV-20-20S-10 P/N 725309 Height of Pump Center Line When Mounted to Subplate 6.25 (158.8 mm) Subplate and mounting bolts are not included with subplate mounted pumps and must be specified in addition to the pump. Example: (1) PSV-PNSO-20HRM-56 Pump (1) PSV-20-20S-10 Subplate * Includes bolt kit B-16 to mount pump to subplate. Foot Bracket * Bracket Model Number PSV-20-70B P/N 959770 Height of Pump Center Line When Mounted to Subplate 7.00 (177.8 mm) * Includes bolt kit B-90 to mount pump to bracket. Foot bracket and mounting bolts are not included with flange mounted pumps and must be specified in addition to the pump Example: (1) PSV-PSCO-20HRM-66 Pump (1) PSV-20-70B Bracket Flange Kit F lange Kit No. Consists of: PSV-20-20F-60 P/N 953638 1 Ea 1 1 /2" NPT Flange (Inlet) 4 Ea 1 /2-13 x 1.75 Socket Head Cap Screw 1 Ea 1 /8 x 1 7 /8 x 2 1 /8 O-ring 1 Ea 1" NPT FLange (Outlet) 4 Ea 3 /8-16 x 1.5 Socket Head Cap Screw 1 Ea 1 /8 x 1 1 5/ 16 x 1 9 / 16 O-ring Flanges are not included with pumps which have 4 bolt flange ports and must be specified in addition to the pump Example: (1) PSV-PSCO-20HRM-66 Pump (1) PSV-20-20F-60 Flange Kit
Bosch Rexroth Engineering Data Variable Volume Vane Pumps Models SV-20 & SV-25 15
Bosch Rexroth Corporation Industrial Hydraulics Division 2315 City Line Road Bethlehem, PA 18017 Phone (610) 694-8300 Fax (610) 694-8467 www.boschrexroth-us.com Bosch Rexroth Corporation*# Pneumatics P.O. Box 13597 1953 Mercer Road Lexington, KY 40511-1021 Phone (859) 254-8032 Fax (859) 254-4188 (800) 489-4188 Email: customer.pneumatics @boschrexroth-us.com www.boschrexroth-us.com Bosch Rexroth Corporation Electric Drives and Controls 5150 Prairie Stone Parkway Hoffman Estates, IL 60192-3707 Phone (847) 645-3600 Fax (847) 645-6201 Email: info@indramat.com www.boschrexroth-us.com Bosch Rexroth Corporation Linear Motion and Assembly Technologies 816 East Third Street Buchanan, MI 49107 Phone (616) 695-0151 Fax (616) 695-5363 www.boschrexroth-us.com Bosch Rexroth Corporation* Mobile Hydraulics Division P.O. Box 395 1700 Old Mansfield Road Wooster, OH 44691-0394 Phone (330) 263-3300 Fax (330) 263-3333 Email: info@rexroth.com www.boschrexroth-us.com Bosch Rexroth AG Zum Eisengiesser 1 D-97816 Lohram Main Telefon +49 (0) 93 52/18-11 Fax +49 (0) 93 52/18-11 90 Email: pr@rexroth.de www.boschrexroth.de *ISO9001 Certified Quality System #QS9000 Certified Quality System For more information, you may contact your nearest Bosch Rexroth distributor: 9 535 233 089 4/02