Catalog HY13-155-2/US Technical Information Series PVP 1/14 Performance Information Series PVP 1/14 Compensated, Variable Volume, Piston Pumps Features High Strength Cast-Iron Housing for Reliability and Quiet Operation Replaceable Bronze Port Plate to llow Easy Field Serviceability Replaceable Piston Slipper Plate Thru-Shaft Capability SE, B and C Pilots vailable Low Noise Levels Fast Response Times Metric Pilot Shaft and Ports vailable Low Control s for Reduced Draw (Energy Efficient) Controls Compensation Remote Compensation Load Sensing djustable Maximum Volume Stop Low Standby Hi/Lo Torque () Limiting Schematic Symbol (Basic Pump) Special Installation or Fluids Consult your Parker Representatives on applications requiring higher than rated pressure, over-speed conditions, indirect drive, fluids other than mineral base fluid, and operation at temperatures above 71 C (16 F). Quick Reference Data Chart Pump Model hpm12-1.p65, lw, jk Displacement cc/rev (In 3 /rev) Specifications Ratings Outlet Port: 248 bar (36 ) Continuous (P1) 31 bar (45 ) Peak (P3) Inlet Port: 1.72 bar (25 ) Maximum. bar ( In. Hg.) Vacuum Minimum @ 18 RPM Case Drain:.3 bar (5 ) Maximum Differential over Inlet Port. 1. bar (15 ) Maximum Speed Ratings: 6 to 18 RPM Operating Temperature Range: 4 C to 71 C ( 4 F to 16 F) Housing Material: Cast-Iron Filtration: ISO 16/13 Recommended ISO 18/15 Maximum Mounting: SE C 2-Bolt or Diagonally on a SE C 4-Bolt SE D 2-Bolt or Diagonally on a SE D 4-Bolt Metric 2-Bolt Installation Data: See Installation Information on page 244 for specific recommendations pertaining to system cleanliness, fluids, start-up, inlet conditions, shaft alignment, drain line restrictions and other important factors relative to the proper installation and use of these pumps. Pump Delivery *pprox. Noise Levels db() Input t @ 7 bar (1 ) @ Full 18 RPM (12 RPM) 18 RPM, Max. in LPM () 34 bar bar bar 27 bar 248 bar Displacement & 12 RPM 18 RPM (5 ) (1 ) (2 ) (3 ) (36 ) 248 bar (36 ) PVP1 1. (6.1) 12. (31.7) 18. (47.5) 73 (67) 75 () 78 (72) 79 (75) 81 (75) 83.6 kw (112. hp) PVP14 14. (8.54) 171. (45.5) 252. (67.) 8 (71) 8 (72) 8 (75) 82 (76) 84 (77) 117.9 kw (158. hp) * Since many variables such as mounting, tank style, plant layout, etc., effect noise levels, it cannot be assumed that the above readings will be equal to those in the field. The above values are for guidance in selecting the proper pump. Noise levels are -weighted, mean sound pressure levels at 1 meter from the pump, measured and recorded in accordance with applicable ISO and NFP standards. 194
Catalog HY13-155-2/US Ordering Information Series PVP 1/14 PVP Displacement Painting Multiple Pump Shaft Port Rotation Volume Thru- Thru- Control Seals Multiple Pumps Variable Range Option Stop Shaft Shaft Option Pumps Piston Option Threads Option Maximum Displacement CC s/rev. (Cu.In s/rev.) 1 1 CC/Rev (6.1) 14 14 CC/Rev (8.5) R L Rotation * Right (CW) Left (CCW) * Viewed from shaft end. P Painting No Paint Paint Multiple Pumps Range* 1 17- bar (25-1 ) 2 17- bar (25-2 ) 3 17-27 bar (25-3 ) 36 17-248 bar (25-36 ) * Minimum value of pressure range only applies on control option omit code. Multiple Pumps Single Pump Factory Mounted To Rear of nother Pump Vol. Stop Option Thru-Shaft Thds No Thru-Shaft 6* UNC 9** Metric * vailable with 2 port option. ** vailable with 8 or 9 port option. No Volume Stop 2 dj. Max. Vol. Stop V Nitrile Single Pump Pump Factory Mounted On Rear Seals Fluoroelastomers* * FLUOROELSTOMERS are available under various registered trademarks, including FLUOROCRBON (a registered trademark of DuPont) and FLUOREL (a registered trademark of 3M). Control Option Standard Comp. M Remote (Master) ME Remote (Slave) Shaft Pilot * 1-1/4" Keyed (SE C) SE C B* 14T Spline (SE C) SE C C 1-1/2" Keyed (SE CC) SE C D 17T Spline (SE CC) SE C E 1-3/4" Keyed (SE D) SE D F 13T Spline (SE D) SE D G 1-3/4" Keyed (SE D) SE C H 13T Spline (SE D) SE C K 4mm Keyed Metric * Maximum torque is 639. N m (568 In-Lbs). vailable with 8 or 9 porting options only. 4 B3 HLM* HL* S Thru-Shaft Option No Thru-Shaft and Remote and Hi/Lo,, and Hi/Lo Servo Vol. & (Int) SF Servo Vol. & (Ext) * Specify, RPM & comp setting when ordering or will be get default. SE Pilot / SE 9T Spline SE B Pilot / SE B 13T Spline B4 SE B Pilot / SE BB 15T Spline C3 SE C Pilot / SE C 14T Spline Port Option Port Type 2 Side Flange (Inch) SE 8 Side Flange (Metric Thds.) ISO 6149 hpm12-1.p65, lw, jk 9 Side Flange (Metric Thds.) BSPP 195
Catalog HY13-155-2/US Performance Data Series PVP 1/14 Typical Performance Data - Fluid: Standard Hydraulic Oil 1 SSU @ 49 C (12 F) 1 9 8 7 6 LPM 181.8 48 121.2 9.9 6.6 3.3 4 32 24 16 8 PVP1 @ 12 RPM Full 1 2 59.7 52.2 37.3 29.8 22.4 7.5 27 238 3 35 8. 7. 6. 5. 4. 3. 2. 1. 1 9 8 7 6 LPM 181.8 48 121.2 9.9 6.6 3.3 4 32 24 16 8 PVP1 @ 15 RPM 1 Full 2 27 238 3 35 78.3 15. 55.9 33.6 11.2 9. 75. 6. 45. 22.4 3. 15. Note: Compensated horsepower curves are shown for the standard pressure compensator option. For remote type compensators the compensated horsepowers will be 1-15% higher. Note: The efficiencies and data in the graphs are accurate for pumps running at speeds shown and maximum stroke. To calculate approximate horsepower for other conditions, use the following formula... = [ Q x () + Compensated 1714 ] 1 9 8 7 6 LPM 181.8 48 121.2 9.9 6.6 4 32 24 16 PVP1 @ 18 RPM Full 89.5 74.6 12. 1. 59.7 8. 6. 29.8 4. PVP 1/14 Inlet Characteristics at Full Displacement (Graph only valid at sea level) Inlet Vacuum bar.55.41.27 hpm12-1.p65, lw, jk 8 6 4.14 2 bar In-Hg.17.34.51.68-2 -4-6 -8 Recommended Operating Condition DO NOT OPERTE IN THIS REGION 3 6 9 12 15 18 Shaft Speed - RPM LPM 11.3 3. 9.4 2.5 7.6 2. 5.7 1.5 3.8 1. 1.9.5 3.3 8 1 2 27 238 3 35 PVP 1/14 pproximate Case Drain verage of 12, 15 & RPM 34 52 13 172 27 241 5 75 1 15 2 25 3 35 Std. Comp. Remote Comp. Full flow 2. 196
Catalog HY13-155-2/US Performance Data Series PVP 1/14 Typical Performance Data - Fluid: Standard Hydraulic Oil 1 SSU @ 49 C (12 F) 1 9 8 7 LPM 181.8 48 4 PVP14 @ 12 RPM 78.3 15. 55.9 9. 75. 1 9 8 7 LPM 34.7 283.9 9 75 PVP14 @ 15 RPM 149.2 2. 13.6 175. 111.9 15. 93.3 125. 6 121.2 9.9 6.6 3.3 32 24 16 8 Full 1 2 33.6 11.2 27 238 3 35 6. 45. 22.4 3. 15. 6 227.2 17.3 113.6 56.8 6 45 3 15 Full 1 2 6. 18.7 27 238 3 35 74.6 1. 75. 37.3 5. 25. Note: Compensated horsepower curves are shown for the standard pressure compensator option. For remote type compensators the compensated horsepowers will be 1-15% higher. Note: The efficiencies and data in the graphs are accurate for pumps running at speeds shown and maximum stroke. To calculate approximate horsepower for other conditions, use the following formula... = [ Q x () + Compensated 1714 ] 1 9 8 7 6 LPM 34.7 9 283.9 227.2 17.3 113.6 56.8 75 6 45 3 15 Response Times PVP14 @ 18 RPM 1 Full 2 93.3 6. 18.7 27 238 3 35 149.2 2. 13.6 175. 111.9 15. 125. 74.6 1. 75. 37.3 5. 25. Time (millisec) hpm12-1.p65, lw, jk 45 4 35 3 25 2 15 1 5 PVP 1 @ 18 RPM 1 2 On-Stroking De-Stroking 27 3 275 4 197 Time (millisec) 6 5 4 3 2 1 PVP 14 @ 18 RPM 1 2 On-Stroking De-Stroking 27 3 275 4
VRIBLE VOLUME PUMP INITIL FCTORY SETTINGS BELOW @ ROTTION RPM Catalog HY13-155-2/US Dimensional Data Series PVP 1/14 Side Ported Option 2 Dimensions * Inch equivalents for millimeter dimensions are shown in (**). NOTES: 1. Righthand (CW) rotation, side ported pump shown. Lefthand (CCW) pumps have inlet port, outlet port, cover drain port and compensator on opposite side as viewed from rear of pump. 2. Pump shown with standard pressure compensator (control option omit ). 3/8 X 1-3/8 WOODRUFF KEY 42.39 (1.66) 42.14 (1.65) 5/16 X 1 WOODRUFF KEY 35.33 (1.39) 35.8 (1.38) 31.75 (1.25) ø 31.7 (1.24) 55.37 (2.18) SHFT OPTION OMIT (SE C ) MX TORQUE = 639. N m (5,68 IN-LBS) 11.13 (.437)/11.6 (.435) SQURE X 1.5 LONG KEY 49.43 (1.94) 49.17 (1.93) 55.37 (2.18) SHFT OPTION B (SE C ) 14 TOOTH 12/24 PITCH MX TORQUE = 639. N m (5,68 IN-LBS) 61.72 (2.43) SHFT OPTION C (SE CC ) MX TORQUE = 1212.8 N m (1,78 IN-LBS) DRIN PORT OPTION 2 - SE-12 STRIGHT THRED (1-1/16-12 UN) ø 38.1 (1.5) 38.5 (1.49) 61.72 (2.43) SHFT OPTION D (SE CC ) 17 TOOTH 12/24 PITCH MX TORQUE = 1212.8 N m (1,78 IN-LBS) CLERNCE FOR ø.625 MOUNTING BOLT (SE C MOUNTING PTTERN) ø 44.45 (1.75) 44.4 (1.74) 74.68 (2.94) SHFT OPTION E or G (SE D ) MX TORQUE = 1687.5 N m (15, IN-LBS) DJUSTBLE MX VOLUME STOP OPTION FLOW CHNGE: PVP1 = 6.25 CC/REV/TURN PVP14 = 8.72 CC/REV/TURN PPROX. 324.61 (12.78) T FULL FLOW 74.68 (2.94) SHFT OPTION F or H (SE D ) 13 TOOTH 8/16 PITCH MX TORQUE = 1687.5 N m (15, IN-LBS) 39.37 (1.55) 127. (5.) 121.92 (4.8) HYDRULIC PUMP/MOTOR DIVISION Otsego, MI 4978 MDE IN US CC/REV MX 121.92 (4.8) SE D ø152.4 (6.) 152.34 (5.998) Front View 9.42 (3.56) 114.3 (4.5) 13.5 (5.12) 9.42 (3.56) 114.3 (4.5) 13.5 (5.12) 86.36 (3.4) CLERNCE FOR ø.75 MOUNTING BOLT (SE D MOUNTING PTTERN) Top View PRESSURE COMPENSTOR DJUSTMENT SENSITIVITY: PPROX. 55.2 BR (8 ) PER TURN 154.94 (6.1) PPROX @ MIN PRESSURE 2.3 (.8) 89.92 (3.54) 11.9 (3.98) IN OUT 115.67 (4.55) 129.79 (5.11) 89.92 (3.54) SE C ø 127. (5.) 126.95 (4.998) 112.27 (4.42) LTERNTE DRIN PORT (USE IF PUMP IS INVERTED) OPTION 2 - SE-12 STRIGHT THRED (1-1/16-12 UN) hpm12-1.p65, lw, jk 63.5 (2.5) Rear View INLET - 2-1/2" SE 4 BOLT FLNGE STNDRD PRESSURE SERIES (CODE 61) - OPPOSITE SIDE (1/2-13 THRED FOR PORT OPTION 2 PUMPS) 341.63 (13.45) 288.29 (11.35) 276.46 (1.53) 12.45 (.49) 19.5 (.75) Side View OUTLET - 1-1/2" SE 4 BOLT FLNGE HIGH PRESSURE SERIES (CODE 62)- THIS SIDE (5/8-11 THRED FOR PORT OPTION 2 PUMPS) 198
VRIBLE VOLUME PUMP INITIL FCTORY SETTINGS BELOW @ ROTTION RPM Catalog HY13-155-2/US Dimensional Data Series PVP 1/14 Side Ported Options 8 & 9 Dimensions * Inch equivalents for millimeter dimensions are shown in (**). NOTES: 1. Righthand (CW) rotation side ported pump shown. Lefthand (CCW) pumps have inlet port, outlet port, cover drain port, and compensator on opposite side as viewed from rear of pump. 2. Pump shown with standard pressure compensator (control option omit ). See page 239 for installation dimensions of remote compensator (control options M, ME, or ). Pilot Dimensions Shaft Option Dia. B C D, B, C, D, G, H 127./126.95 (5./4.998) 12.45 (.49) 9.42 (3.56) 15.88 (.625) E, F 152.4/152.34 (6./5.998) 12.45 (.49) 114.3 (4.5) 19.5 (.75) K 124.99/124.94 (4.921/4.919) 9.53 (.38) 9 (3.54) Ø18 (.78) 5/16 X 1 WOODRUFF KEY 35.33 (1.39) 35.8 (1.38) ø31.75 (1.25) 31.7 (1.24) 55.37 (2.18) SHFT OPTION OMIT (SE C ) MX TORQUE = 639. N m (5,68 IN-LBS) 11.13 (.437)/11.6 (.435) SQURE X 1.5 LONG KEY 49.43 (1.94) 49.17 (1.93) 55.37 (2.18) SHFT OPTION B (SE C ) 14 TOOTH 12/24 PITCH MX TORQUE = 639. N m (5,68 IN-LBS) 3/8 X 1-3/8 WOODRUFF KEY 42.39 (1.66) 42.14 (1.65) ø38.1 (1.5) 38.5 (1.49) 61.72 (2.43) SHFT OPTION C (SE CC ) MX TORQUE = 1212.8 N m (1,78 IN-LBS) 12 X 8 X 7 MM KEY 43. (1.3) 42.72 (1.682) 61.72 (2.43) SHFT OPTION D (SE CC ) 17 TOOTH 12/24 PITCH MX TORQUE = 1212 N m (1,78 IN-LBS) 74.68 (2.94) ø 44.45 (1.75) 44.4 (1.74) SHFT OPTION E or G (SE D ) MX TORQUE = 1687 N m (15, IN-LBS) 74.68 (2.94) SHFT OPTION F or H (SE D ) 13 TOOTH 8/16 PITCH MX TORQUE = 1687 N m (15, IN-LBS) 4. (1.574) ø 39.95 (1.572) 91.95 (3.62) SHFT OPTION K (4MM) ONLY VILBLE WITH 125MM PILOT MX TORQUE = 14 N m (12,45 IN-LBS) DRIN PORT OPTION 8 - ISO 6149-12 (M27X2.) OPTION 9-3/4" BSPP D MOUNTING 2-BOLT PTTERN DJUSTBLE MX VOLUME STOP OPTION FLOW CHNGE: PVP1 = 6.25 CC/REV/TURN PVP14 = 8.72 CC/REV/TURN PPROX. 324.61 (12.78) T FULL FLOW 39.37 (1.55) 127. (5.) 121.92 (4.8) HYDRULIC PUMP/MOTOR DIVISION Otsego, MI 4978 MDE IN US CC/REV MX 121.92 (4.8) C C Front View Top View 13.5 (5.12) 13.5 (5.12) 86.36 (3.4) PRESSURE COMPENSTOR DJUSTMENT SENSITIVITY: PPROX. 55.2 BR (8 ) PER TURN 154.94 (6.1) PPROX @ MIN PRESSURE 89.92 (3.54) 2.3 (.8) IN 115.67 (4.55) 129.79 (5.11) 11.9 (3.98) 89.92 (3.54) 112.27 (4.42) LTERNTE DRIN PORT (USE IF PUMP IS INVERTED) OPTION 8 - ISO 6149-12 (M27X2.) OPTION 9-3/4" BSPP hpm12-1.p65, lw, jk 63.5 (2.5) M6X1. THREDS FOR THRU-SHFT MOUNTING Rear View OPPOSITE SIDE INLET 2-1/2" SE 4-BOLT FLNGE STNDRD PRESSURE SERIES (CODE 61) M12X1.75 THRED 341.63 (13.45) 288.29 (11.35) 276.46 (1.53) 19.5 (.75) THIS SIDE OUTLET 1-1/2" SE 4-BOLT FLNGE HIGH PRESSURE SERIES (CODE 62) M16X2. THRED B Side View 199
CC/REV MX HYDRULIC PUMP/MOTOR DIVISION Otsego, MI 4978 MDE IN US VRIBLE VOLUME PUMP INITIL FCTORY SETTINGS BELOW @ ROTTION RPM Catalog HY13-155-2/US Dimensional Data Series PVP 1/14 Thru-Shaft Pump Dimensions * Inch equivalents for millimeter dimensions are shown in (**). NOTES: 1. Righthand (CW) rotation, side ported pump shown. Lefthand (CCW) pumps have inlet port, outlet port, cover drain port and compensator on opposite side as viewed from rear of pump. 2. Pump shown with standard pressure compensator (control option omit ). 3. Maximum torque transmitting capacity for rear mounting of pumps = 639. N m (568 In-Lbs). Lower allowables may apply based on pump mounted on rear. C C Top View SHFT LENGTH OF RER PUMP F IN OUT D Front View DPTER MY BE ROTTED 9 IF DESIRED øb E 322.74 (13.1) Side View Dimensions Thru Shaft Options VRITION B C D E F 64 364.49 (14.35) 82.58/82.6 (3.251/3.252) 53.19 (2.9) 3/8-16UNC-2B 9 Tooth 16/32 Pitch 31.8 (1.25) 6B3 378.46 () 11.63/11.65 (4.1/4.2) 73.3 (2.88) 1/2-13UNC-2B 13 Tooth 16/32 Pitch 41.1 (1.62) 6B4 378.46 () 11.63/11.65 (4.1/4.2) 73.3 (2.88) 1/2-13UNC-2B 15 Tooth 16/32 Pitch 46. (1.81) 6C3 388.11 (15.28) 127.3/127.5 (5.1/5.2) 9.5 (3.56) 5/8-11UNC-2B 14 Tooth 12/24 Pitch 55.4 (2.18) 94 364.49 (14.35) 82.58/82.6 (3.251/3.252) 53.19 (2.9) M1 X 1.5 9 Tooth 16/32 Pitch 31.8 (1.25) 9B3 378.46 () 11.63/11.65 (4.1/4.2) 73.3 (2.88) M12 X 1.75 13 Tooth 16/32 Pitch 41.1 (1.62) 9B4 378.46 () 11.63/11.65 (4.1/4.2) 73.3 (2.88) M12 X 1.75 15 Tooth 16/32 Pitch 46. (1.81) 9C3 388.11 (15.28) 127.3/127.5 (5.1/5.2) 9.5 (3.56) M16 X 2. 14 Tooth 12/24 Pitch 55.4 (2.18) hpm12-1.p65, lw, jk 2
VRIBLE VOLUME PUMP INITIL FCTORY SETTINGS BELOW @ ROTTION RPM Catalog HY13-155-2/US Characteristics Series PVP 1/14 Remote Compensator Pump Dimensions * Inch equivalents for millimeter dimensions are shown in (**). NOTES: 1. Righthand (CW) rotation side ported pump shown. Lefthand (CCW) pumps have inlet port, outlet port, cover drain port, and compensator on opposite side as viewed from rear of pump. 2. When controlling pump compensator pressure with remote relief valve, size relief valve to pass a minimum of 1.89 LPM (.5 ). HYDRULIC PUMP/MOTOR DIVISION Otsego, MI 4978 MDE IN US CC/REV MX DPTOR FITTING SUPPLIED WITH PORT OPTION 8 PUMPS ISO 6149-4 (M12X1.5) 17.2 (.67) 13 (6.58) REF SE -4 STRIGHT THRED O-RING PORT (7/16-2 UNF-2B) INTERNL ORIFICE INSTLLED IN OPTIONS ME & Top View 181.35 (7.14) PPROXIMTE 186.18 (7.33) PPROXIMTE 235.96 (9.29) DPTOR FITTING SUPPLIED WITH PORT OPTION 9 PUMPS 22.86 (.9) 1/4" BSPP PRESSURE COMPENSTOR DJUSTMENT SENSITIVITY: PPROX. 82.7 BR (12 ) PER TURN DIFFERENTIL PRESSURE DJUSTMENT SENSITIVITY: PPROX. 27.6 BR (4 ) PER TURN (INCLUDED ON CONTROL OPTION) 13 (6.58) REF 86.36 (3.4) 13 (6.58) Side View Front View hpm12-1.p65, lw, jk 21
VRIBLE VOLUME PUMP CC/REV MX INITIL FCTORY SETTINGS BELOW @ ROTTION RPM Catalog HY13-155-2/US Dimensional Data Series PVP 1/14 Hi/Lo (Torque) Control Pump Dimensions *U.S. Patent #6,95,76 * Inch equivalents for millimeter dimensions are shown in (**). NOTES: 1. Righthand (CW) rotation side ported pump shown. Lefthand (CCW) pumps have inlet port, outlet port, cover drain port, and compensator on opposite side as viewed from rear of pump. 2. When controlling pump compensator pressure with remote relief valve, size relief valve to pass a minimum of 1.89 LPM (.5 ). OPTIONL MX VOLUME STOP Typical Hi-Lo Control / Characteristics HYDRULIC PUMP/MOTOR DIVISION Otsego, MI 4978 MDE IN US CONSTNT POWER CURVE Outlet LOW PRESSURE DJUSTMENT MX. DJUST LOW FLOW SETTING DJUSTMENT System Top View MXIMUM PRESSURE DJUSTMENT LOW FLOW SETTING DJUSTMENT 157.73 (6.21) 58.67 (2.31) LOW PRESSURE DJUSTMENT Side View Front View hpm12-1.p65, lw, jk 22
Catalog HY13-155-2/US Characteristics Series PVP 1/14 % of Full 1 8 6 4 2 Low Knee Typical Hi-Lo Characteristics 34 5 MXIMUM PRESSURE (See Chart 1) FLOW 13.8 BR (2 ) FLOW @ 13.8 BR (2 ) BELOW COMPENSTOR SETTING (See Chart 2) High Knee 1 13 15 (Typical) 2 COMPENSTOR SETTING 172 25 Determining how much the pressure will increase at the Low Knee by manually destroking the pump. 1. From Chart 1 read the maximum obtainable pressure (P1) at the low pressure knee at the input power desired for the desired speed (N). 2. Calculate the theoretical full flow (Q1) of the pump at the desired speed. (cc/rev) X (N) Q1 (gpm) = 3785 3. Pick a reduced output flow (Q2). This is done by decreasing the output of the pump using the optional volume stop. 4. pproximate the new maximum pressure at the low pressure knee for the input power desired (P2). Q1 X P1 P2 = Q2 Chart 1: Max Full 27 172 13 34 3 25 2 15 1 5 PVP1 Maximum @ Full 7.5 1 2 22.4 3 29.8 4 37.3 5 6 Input 12 RPM 52.2 7 59.7 8 15 RPM 18 RPM 9 74.6 1 Chart 1: Max Full 27 172 13 34 3 25 2 15 1 5 PVP14 Maximum @ Full 7.5 1 2 22.4 3 29.8 4 37.3 5 6 Input 12 RPM 52.2 7 59.7 8 15 RPM 18 RPM 9 74.6 1 Chart 2: PVP1 Maximum @ 13.8 (2 ) Below Compensator Setting Maximum LPM 227.2 189.3 113.6 75.7 37.9 6 5 4 3 2 1 (pplies at speeds of 12 thru 18 RPM) Maximum at 15 RPM Maximum at 12 RPM Comp @ 172 (25 ) Comp @ (2 ) Comp @ 27 (3 ) Comp @ 248 (36 ) Chart 2: Maximum LPM 227.2 189.3 113.6 75.7 37.9 6 5 4 3 2 1 PVP14 Maximum @ 13.8 (2 ) Below Compensator Setting (pplies at speeds of 12 thru 18 RPM) Maximum at 15 RPM Maximum at 12 RPM Comp @ 172 (25 ) Comp @ (2 ) Comp @ 27 (3 ) Comp @ 248 (36 ) 7.5 1 2 22.4 3 29.8 4 37.3 5 6 Input 52.2 7 59.7 8 9 74.6 1 7.5 1 2 22.4 3 29.8 4 37.3 5 6 Input 52.2 7 59.7 8 9 74.6 1 hpm12-1.p65, lw, jk 23