MULTIFUNCTION SPOOL VALVES air operated and air operated G/-G - ISO 99/ subbase-mounted body /-/ Series Type ISO size MULTIFUNCTION Multifunction selector The multifunction selector is equipped with pilot selector seals (A) located between the body (B) and the covers (C), on both sides : pilot and. Each selector can be set on or positions. Rotating or turning it upside-down allows the following functions : - internal or to pilot or operators. - selection of the type of operator : air operated or -air pilot or. For this, it is only necessary to position one of the arrows of the selector into the notch matching the diagram of the required function (see below). Functions can be modifi ed at will.the valves are delivered with the selector pre-set on the position corresponding to the function requested on order (see table CHOICE OF EQUIPMENT). External supply enables the valves to be used with a fl uid pressure ranging from 0 to bar and with vacuum. Selection of supply (internal / external) Selection of the type of operator 80 C A B 80 E Pilot function C A B Pilot operators Return operators Differential 0006GB-008/R0 Air operated Notches for selector positionning Solenoid differential Solenoid differential Air operated Differential Spring P7-
ISO 99/ SIZE SPOOL VALVES - SERIES Operating principle Blanking plate (with an air operated pilot) pilot Changing from an air operated valve to a differential valve An air operated valve can be changed into a differential valve by turning over the outside piston ring as shown in the diagram below (). Air operated Differential Manual operator using a tester (option) A manual operator can be equipped with a tester () by knocking the knock-out plug () out of the end cover. An air operated valve can be changed into a air valve by : - re-positionning the selector seal, - removing the upper blanking plate (side or ), - fi tting a selector seal if lacking, - adding a pilot valve on the upper part. A air valve can be changed into an air operated valve by : - removing the pilot valve, - fi tting a blanking plate on the pilot base (plate code : 880007), - re-positionning the selector seal. USE WITH UNLUBRICATED AIR This range of JOUCOMATIC valves will operate satisfactorily with lubricated air or unlubricated air and even with dry air, due to a sealing device which has been patented. Essentially, a "T" seal backed up by a cushioning or compensation seal. This arrangement of seals assures a minimum pilot pressure which will remain constant even after the valve has been stopped for a long period of time. When re-starting, the performance of the valve will be the same as during continuous operation. This important "non-stiction" characteristic assures satisfactory performance under all conditions. P7-0006GB-008/R0
MULTIFUNCTION SPOOL VALVES air operated G/-G - ISO 99/ subbase-mounted body FEATURES Choice of internal/ with selector seals (vacuum use to 0,90 bar) /-/ Series Type ISO size GENERAL Fluid Air or neutral gas, fi ltered, lubricated or not Operating pressure 0.90 to + bar (with to pilot) +. to +0/ bar (with to pilot) Pilot pressure See specifi cations tables Ambient temperature 0 C to +0 C Flow (Qv at 6 bar) 600 l/min (ANR) (with subbase G /) 7000 l/min (ANR) (with subbase G ) Flow coefficient Kv = 90 (with subbase G /) Kv = 00 (with subbase G ) Life millions of cycles (in normal operating conditions) Base ISO 99/ - Size Subbase Single subbase ISO/AFNOR NF E908 CONSTRUCTION Body and cover Seals Internal parts ELECTRICAL CHARACTERISTICS type of coil series 9 voltage Die-cast zinc alloy NBR (nitrile) Light alloy and POM (polyacetal), die-cast zinc alloy inrush consumption hold ~ V-8V-V-0V-0 Hz VA 6 VA ( W) = V-8V W insulation class protection degree F IP 6 electrical connection spade plug size 0 connector, ISO00/EN70-80, form A, rotatable by 90 E SPECIFICATIONS / function / symbol operators pilot () air operated () energized response time (ms) de-ener gized min. pilot pressure (bar) max. catalogue numbers pilot valve + quantity & catalogue number with standard connector (M) spring 60 0, 9007 differential 90 70 9008 + x 90000 90000 90000 0006GB-008/R0 air differential air operated 0 -, 9009 0-9000 0 -, 900 (M) Type of manual operator on pilot(s) : : without : maintained : impulse + x 90000 90000 90000 P7-
ISO 99/ SIZE SPOOL VALVES - SERIES SPECIFICATIONS / function operators / pilot () air operated symbol () response time (ms) energized de-ener gized pilot pressure (bar) min. max. catalogue numbers pilot valve + quantity & catalogue number with standard connector (M) Pressure held W Pressure release W 70 0 900 70 0 900 + x 90000 90000 90000 (M) Type of manual operator on pilot(s) : : without : maintained : impulse OPTIONS Equipment with manual testers so that the spool position can be checked Solenoid valve pilot / series 9 with head and waterproof metal enclosure (see page P-6) complying with European standards EEx "d", "m" or "me" for use in explosive atmospheres Solenoid valve intrinsically safe series 9/ia certifi ed EEx «ia» Connector with cable m long - code : 886 Connector with transil protection (see Coils and accessories section) Solenoid valve with plug and built-in visual control and protection : Solenoid valve without connector + Connector with built-in visual control and VDR/RC protection type of valve 9 NC () (M) valve without connector catalogue number 9000 9000 9000 catalogue number (~ / =) V 8V V 0V + 8860 8860 8860 88608 (M) Type of manual operator on pilot(s) : : without : maintained : impulse () Solenoid valve series 9 - / NC - Ø,mm with exhaust in base SUBBASES type of subbases single subbases with side port subbase catalogue number port orifices - -- - 00 G /8 G / G / 0008 G /8 G G P7-0006GB-008/R0
ISO 99/ SIZE SPOOL VALVES - SERIES DIMENSIONS (mm), WEIGHT (kg) VALVE ON SINGLE SUBBASE WITH SIDE PORT Subbase mounting G : holes Ø 7 Subbase mounting G / : holes Ø 9 Pilots series 9 ISO00 connector E Ø G/8 (-) Ø G/-G (----) 0006GB-008/R0 code subbase port orifices dimension weight - -- - A B C D E F H J K L M with pilot 9 with pilots 9 00 G /8 G / G / 9 77 8, 89 9 6 88 0,860,0 0008 G /8 G G 86 7 80 07 60 7 0 8 6 06 0,960,0 + mm for plug removal P7-
ISO 99/ SIZE SPOOL VALVES - SERIES P7-6