Thank you for choosing CYmodel Global : www.cymodel.com ustralia : www.austars-model.com Italia : www.biellaexpress.com Fokker D-VIII Item Nr: CY8016 Instruction Manual efore commencing assembly,please read these instructions thoroughly. LMOST - REDY - TO - FLY SFETY PRECUTIONS This radio control model is not a toy! First-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent., ssemble this kit only in places out of childrens reach! Take enough safety precautions prior to operating this model., You are responsible for this model s assembly and safe operation! lways keep this instruction manual ready at hand for quick reference,even after completing the assembly. Could cause serious injury or even death SPECIFICTION Wing Span:800 mm (110 in) Wing rea:119.7 dm (1856 sq.in) Fuselage Length: 100 mm (8.5 in) Engine : 80-100cc gas engine Radio : 4 channels,6 servos
REQUIRED FOR OPERTION (Purchase separately) 1 minimum 4channel radio for airplanes (with 6servos). nd dry batteries.! CUTION: Only use a minimum 4channel radio for airplanes! (No other radio may be used!) minimum 4 channel transmitter for airplanes. 5 6 Glue required for engine starting! WRNING: Normal gasoline cannot be used with glow engines. Epoxy Glue Instant glue Glow engine fuel only. 1 -size atteries receiver remote control For handing the radio properly.refer to its instruction manual. attery 3 Servo(need 4 (need ) Switch (need ) 6 servos ) Engine and Muffler Model irplane engine:80-100cc gas engine 7 8 Fuel Pump Silicone Tube Other equipment for enhancing airplane operation & perormance Plug Wrench Fuel Filter Muffler Muffler 9 Engine Starter Purchase a propeller that will match your engine 1V attery (for starter) 0X10----X10 TOOLS REQUIRED ( Purchase separately) Sharp Hobby Knife Phillips Screw Driver wl Needle Nose Pliers Wire Cutters Scissors 1 3.. EFORE YOU EGIN Read through the manual before you begin,so you will have an overall idea of what to do. Check all parts.if you find any defective or missing parts.contact your local dealer. Symbols used throughout this instruction manual,comprise. pply epoxy glue. mm Drill holes with the specified Diameter(here:mm) Must be purchased separately!! Warning! 50 C. pply instant glue (C glue,super glue). Ensure smooth non-binding movement while assembling. Pay close attention here! Do not overlook this symbol. ssemble left and right Sides the same way. Cut off shaded portion. Cut off excess.
! ccessory list for this page. 3 Install the aileron servo.6x1mm Tp - - - - - 8 X10mm.5X85mm rod - - - - - 10 3X35mm HORN 1 Install the aileron 4 Install the aileron servo Servo line 3mm HORN Make sure hinges are mounted in the same line - - - - - - - - 10.6X1mm Tp - - - - - 8 X10mm.5X85mm rod 3X35mm Install the aileron 5 Main wing 3X910mm tube 4mm 0X440mm tube 3
! ccessory list for this page. 8 Main wing&horizontal/vertical tail 4X5mm - - - - - 7 - - - - - - - - 9 4X5mm 6 Install the elevator 9 4mm - - - 7 Install the rudder 10 Horizontal/Vertical tail - - - Securely glue together,if coming off during flights. You lose control of your airplane which leads to accidents! 4
! ccessory list for this page. 13 Install the elevator servo.5x15mm rod 3X5mm - - - - - 9 Rod - - - - 4 1400mm steel wire luminium tube - 3mm Lock Nut 3X0mm Tp - - - - - -1 HORN - - - - - 8 X10mm - - - - - 8 5.mm Collar - 3X3mm - luminum plate.5x15mm rod 3X5mm HORN X10mm 11 Install the rudder 0servo 14 Install the tail pry 3X5mm X10mm 3mm Lock Nut Rod 1400mm steel wire luminium tube - HORN 9mm plywood 9mm plywood 3mm steel wire 1 Install the rudder servo 15 Install the main landing gear Rod luminium tube - X10mm 5.mm Collar - 3X3mm - luminum plate 3X0mm Tp - - - - - -1 5
! ccessory list for this page. 18 Pressure plate 3X0mm Tp - - - - - -1 luminum plate 4X55mm 4X16mm - - - - - - - - - - - 14 4mm Lock nut Install the wing support D D, D D, 4X55mm 4X16mm - - - - - 14 4mm Lock nut 16 Install the main landing gear 19 Main wing&horizontal/vertical tail Pressure plate 3X0mm Tp - - - - - -1 luminum plate - - - - - - C C, C C, E E E E Securely glue together,if coming off during flights. You lose control of your airplane which leads to accidents! 17 Install the wing support 0 Install the engine (80-100cc gas engine) 165mm fuel tank Throttle servo 6
! ccessory list for this page. 3 Radio Equipment 3X5mm Screw Linkage Stopper 3X16mm Screw - - - - 5 3mm rubber band - - - - 7 3mm washer mm Nut - - - - 1 - - - - 1 1.8X0mm Rod - - - - - - 1 3X3mm Screw attery Receiver - - - - 7 - - - - - - 1 1 Install the throttle servo 1 Install the canopy Linkage Stopper - - - - 1 1.8X0mm Rod - - - - - - 1 mm Nut - - - - 1 3X3mm Screw - - - - - - 1 3X5mm Screw 3mm rubber band 3mm washer ssembly of the full tank 5 Install the cowling fter confirming the position(see front of fuel tank). Insert and tighten the. Propeller Spinner Fuel pipe ir pressure line Fuel supply line 3X16mm Screw - - - - 5 3mm rubber band - - - - 5 3mm washer - - - - 5 7
6 djustment. 7 djustment djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. ILERON Side view Top view djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. Rudder Side view Top view 8 djustment. 9 djustment. djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. ELEVTOR Side view Never fly before checking the Cg s required position. In order to obtain the CG specified,reposition the receiver and battery. 170mm Top view CG! ¾ æ Warning! NEVER fly the model without well balancing. 8