ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL Page Electrical Fittings Receptacles Fixture Hangers ccessories and Connectors Junction Boxes In-Channel Joiners Swivel Hangers Cable Entrance Tubing and ccessories 50 53 54 55 59 60 6 62 MTERIL Unistrut fittings, unless noted, are made from hot-rolled, pickled and oiled steel plates, strip or coil, and conform to STM specifications 55, 56, 635, or 36. The fitting steel also meets the physical requirements of STM 50 GR 33. The pickling of the steel produces a smooth surface free from scale. Maple cable saddles, cable clamps and bus bar clamps are made from kiln-dry maple treated with paraffin to a depth of 6" (.6mm). Special sizes of clamps can be fabricated upon request. Porcelain cable clamps are made by the dry process and white glazed. Cable saddles are fiberglass-reinforced polyester. FINISHES Components listed in this section are available in: electro-galvanized (EG), conforming to STM B633 Type III SC; Hot-dipped galvanized (HG), conforming to STM 23 or 53, Perma-Green II (GR), and plain (PL). Note: Many Unistrut Metal Framing components, when used with appropriate closures, are UL listed, and CS approved. DESIGN LOD Design load data, where shown, is based on the ultimate strength of the connection with a safety factor of 2.5, unless otherwise noted. DIMENSIONS Imperial dimensions are illustrated in inches. Metric dimensions are shown in parenthesis or as noted. Unless noted, all metric dimensions are in millimeters and rounded to one decimal place. 48
UNISTRUT RCEWY FILL CHRTS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL U.L. LISTED Unistrut channel is listed by Underwriters' Laboratories as a surface metal raceway. Snap-in closure strip is used to complete the raceway. ccessory parts listed by Underwriters are noted on drawings. The following tables represent maximum number of conductors when raceway is not employed with fixtures or where the clearance between fixtures and raceway is greater than 2" (2.). In all cases the snap-in cover is required to complete raceway enclosure. P3000, & -KO Number and Conductor Size (WG) Gage 4 2 0 8 6 THWN, THHN 2 54 34 2 XHHW 48 3 29 3 0 T, TW 46 36 28 3 THW 30 25 20 0 RH 2 22 3 5 RHH, RHW 9 6 3 5 P3300, P4000 Number and Conductor Size (WG) Gage 4 2 0 8 6 THWN, THHN 40 30 9 9 6 XHHW 26 2 6 5 T, TW 26 20 5 4 THW 4 6 4 RH 5 2 4 3 RHH, RHW 0 9 4 2 P5500, & -KO Number and Conductor Size (WG) Gage 4 2 0 8 6 THWN, THHN 4 05 66 33 23 XHHW 93 3 5 2 9 T, TW 9 58 55 26 5 THW 59 49 39 20 5 RH 53 44 26 4 0 RHH, RHW 3 32 26 4 0 P000, & -KO, P00 & -KO, P2000 & -KO Number and Conductor Size (WG) Gage 4 2 0 8 6 THWN, THHN 88 66 42 20 4 XHHW 58 46 35 6 2 T, TW 5 44 34 6 9 THW 3 30 24 2 9 RH 33 2 6 9 6 RHH, RHW 23 20 6 9 6 P5000, & -KO Number and Conductor Size (WG) Gage 4 2 0 8 6 THWN, THHN 93 05 9 45 32 XHHW 28 0 8 3 2 T, TW 25 98 5 35 20 THW 8 6 54 28 20 RH 3 60 36 9 3 RHH, RHW 5 44 36 9 3 C.S.. PPROVED MXIMUM NUMBER OF WIRES FOR TYPES T, THHN, THW, THWN, TW, R, RH, RHH, RHW OR XHHW Suitable for number of wires in Column when installed to support and supply electric discharge type lighting fixtures when raceway wiring is suitable for at least 5 C except wire suitable for 60 C may be used when clearance between fixtures and raceways is at least 2" (2.). lso suitable for number of wires in column B when installed to support electric discharge type lighting fixtures when raceway wiring is suitable for at least 5 C and clearance between fixtures and raceway is at least 8" (3.2). Raceway Wire Size WG P000, &-KO P00, &-KO P2000. &-KO B B B B B 4 6 0 5 0 4 6 0 0 0 0 2 6 0 4 0 3 6 0 0 0 0 0 5 8 4 6 - - 8 0 8 0 8 4 6 3 4 - - 6 9 6 8 6 2 3 2 2 - - 4 6 4 6 Unistrut channels are also certified by Canadian Standards ssociation. P3000, &-KO P3300, P4000 P5000 &-KO P5500, &-KO 49
ELECTRICL FITTINGS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P53 FG P54 FG 2" (50.8) CBLE SDDLES Maximum "" Cable Diameter Weight/C In mm In mm Lbs kg Material: FG - Fiberglass Reinforced Polyester, PO - Dry Process White Glazed Porcelain P53 FG 2 3 6.4 3 6.2 2 5.4 P54 FG 3 3 4 95.3 4 2 4.3. P53 PO 3 6.2 3 6.2 5 34.0 P54 PO 4 0.6 4 2 4.3 95 43. P2649 thru P2649 H Hole Size 5 8" (4.3) B MPLE CBLE SDDLES 3 8" Flat Head Machine Screw included. Specify hole size when ordering. Order channel nuts as required. Material: Maple hardwood paraffin impregnated. Hole Size "" "B" Weight/C In mm In mm In mm Lbs kg P2649 0-0 - 25.4 3 6.2 3 4 44.5 3 4. P2649 B - 2 25.4-38. 3 2 88.9 2 50.8 38.2 P2649 C 2-2 38. - 50.8 4 0.6 2 4 5.2 4 2.3 P2649 D 2-2 2 50.8-63.5 4 2 4.3 2 2 63.5 5 25.9 P2649 E 2 2-3 63.5-6.2 5 2.0 2 3 4 69.9 68 30.8 P2649 F 3-3 2 6.2-88.9 5 2 39. 3 6.2 80 36.3 P2649 G 3 2-4 88.9-0.6 6 52.4 3 4 82.6 94 42.6 P2649 H over 4 over 0.6 P2645 thru P2645 H 5 8" (4.3) MPLE CBLE CLMPS Hole Size B 3 8" studs, square nuts and washers included. Specify hole size when ordering. Order channel nuts as required. Material: Maple hardwood paraffin impregnated. Hole Size "" and "B" Dimensions Weight/C In mm In mm Lbs kg P2645 0-0 - 25.4 3 2 88.9 84 38. P2645 B - 2 25.4-38. 4 0.6 02 46.3 P2645 C 2-2 38. - 50.8 4 2 4.3 2 54.9 P2645 D 2-2 2 50.8-63.5 5 2 39. 65 4.8 P2645 E 2 2-3 63.5-6.2 6 52.4 89 85. P2645 F 3-3 2 6.2-88.9 6 2 65. 25 9.5 P2645 G 3 2-4 88.9-0.6.8 243 0.2 P2645 H over 4 over 0.6 50
ELECTRICL FITTINGS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P264 thru P264 F 4" (0.6) BUS BR MPLE CLMPS B 5 8" (4.3) 2 " studs, square nuts and washers are included. Channel nuts must be ordered separately. Bus bar maple clamps also available in 4" (6.4) x 2" (50.8) and 4" (6.4) x 6" (52.4) 4" (0.6) 3 8" (8.3) 4" (5.4) Maple Separator Material: Paraffin impregnated maple hardwood. "" "B" No. Bus Wt/C Separators Per Leg Lbs No. Bars In mm In mm kg P264 8 2 25.9 9 32. 0 42 9.0 P264 B 9 2 24.3 3 6 20.6 2 2 465 20.9 P264 C 0 2 266. 5 6 33.3 4 3 509 230.9 P264 D 2 292. 3 6 46.0 6 4 553 250.8 P264 E 2 2 3.5 2 3 8 60.3 8 5 59 20.8 P264 F 3 2 342.9 2 8 3.0 0 6 63 286.2 P690 thru P69 MPLE CBLE CLMPS Hole Size Use with steel clamp and Everdur hardware. Order clamp separately. Specify hole size when ordering. Material: Paraffin impregnated maple hardwood. Order Steel Clamp Number Hole Size "" Wt/C In mm In mm Lbs kg P690 P3 E 0-5 8 0-5.9 2 38. 24 0.9 P69 P5 E 2-2. - 25.4 2 8 54.0 42 9. P692 P E 3 4-2 9. - 38. 2 5 8 66. 54 24.5 P693 P8 E 4-3 4 3.8-44.5 3 6.2 65 29.5 P694 P9 E 2-2 4 38. - 5.2 3 5 8 92. 84 38. P695 P20 E 2-2 2 50.8-63.5 4 8 04.8 0 48.5 P696 P2 E 2 4-3 5.2-6.2 4 5 8.5 23 55.8 P69 P23 E 3-4 6.2-0.6 5 3 4 46. 63 3.9 5
ELECTRICL FITTINGS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P8 thru P95 B PORCELIN CBLE CLMPS Hole Size Use with steel clamp and Everdur hardware. Order clamp separately. Material: Dry process porcelain white glaze. Order Steel Clamp Number Hole Size "" Weight/C In mm In mm Lbs kg P8 3 8 9.5 36 6.3 P8 B P3 E 2 2. 8 4.6 32 4.5 P8 C 5 8 5.9 3 4. P88 3 4 9. 5 25.9 P88 8 22.2 2 3 8 60.3 56 25.4 P88 B P5 E 25.4 55 24.9 P88 C 8 28.6 48 2.8 P89 4 3.8 83 3.6 P89 3 8 34.9 2 8 3.0 82 3.2 P89 B P E 2 38. 5 34.0 P89 C 5 8 4.3 6 30.4 P90 3 4 44.5 85 83.9 P90 8 4.6 4 0.6 80 8.6 P90 B P9 E 2 50.8 60 2.6 P90 C 2 8 54.0 40 63.5 P9 2 4 5.2 200 90. P9 2 3 8 60.3 4 2 4.3 200 90. P9 B P20 E 2 2 63.5 95 88.5 P9 C 2 5 8 66. 90 86.2 P92 2 3 4 69.9 260.9 P92 2 8 3.0 5 8 30.2 240 08.9 P92 B P2 E 3 6.2 240 08.9 P92 C 3 8 9.4 235 06.6 P93 3 4 82.6 38 5.5 P93 3 3 8 85. 6 8 55.6 36 66.5 P93 B P23 E 3 2 88.9 360 63.3 P93 C 3 5 8 92. 350 58.8 P94 3 3 4 95.3 600 22.2 P94 3 8 98.4 4 84.2 580 263. P94 B P24 E 4 0.6 550 249.5 P94 C 4 8 04.8 540 244.9 P95 4 4 08.0 550 249.5 P95 P24 E 4 3 8. 4 84.2 500 226.8 P95 B 4 2 4.3 490 222.3 52
RECEPTCLES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P255 DUPLEX GROUNDED RECEPTCLE P2553 Wire Connectors 25 V, 5 amp receptacle, NEM configuration S-5R, cover plate. #6 screws, nuts and wire connectors included. Leads are 4 gage 05 C plastic covered. Ground wire is green 6 gage. 6" (52.4) Oval Head #6-32 X " P306-0632 Finish: White powder coat. P384 Closure Wt/C 38 Lbs (.2 kg) P26 P262 RECEPTCLE BOX 4" x 5 8" P263 P264 P265 RECEPTCLE UNIT 8" Knockout 8" Knockout 4" x 5 8" Includes Nuts and Screws Includes Nuts and Screws P306-420 P306-420 Outlet Weight/C Lbs kg P26 Single 88 39.9 P262 Duplex 88 39.8 Outlet Lbs Weight/C P263 25V 08 49 5-5R P264 250V 08 49 6-5R P265 2V 08 49-5R kg NEM Receptacle Configuration 53
FLUORESCENT FIXTURE HNGERS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P253 P553 FLOURESCENT FIXTURE HNGERS 4" X " RHMS and Sq. Nut Included P2539 P3539 P5539 FLOURESCENT FIXTURE HNGERS 4" X " RHMS and Sq. Nut Included Hanger provides more than 2 " (2.) space between channel and fixtures. Materials: 8 gage (.2). 9 32" (.) Dia. Hole 5 8" (4.3) Design Load 20 Lbs (.5 kn) Hanger provides 8" (3.2) space between channel and fixtures. Materials: 8 gage (.2). 5 8" (4.3) 4" X 3 4" Carriage Bolt and Sq. Nut Included Design Load 20 Lbs (.5 kn) Part Number Use With Channel "" Weight/C In mm Lbs kg P000 P253 P00 2 6 6.9 9 8.6 P2000 P3000 P553 P5500 3 4 82.6 22 0.0 Part Number Use With Channel "" Weight/C In mm Lbs kg P000 P2539 P00 3 4 44.5. P2000 P3539 P3000 2 38. 5 6.8 P5539 P5500 2 9 6 65. 8 8.2 P255 P256 P25 RCEWY HNGERS P2855 P2856 P285 RCEWY HNGERS 4 4" (08.0) 2 3 4" (69.9) 9 32" (.) Sq. Hole 9 32" (.) Sq. Hole Use with Channels: P00, P0, P200, P5000, & P5500. Design Load 20 Lbs (.5 kn) Use with Channels: P000, P00, P2000, P3000, P3300, P4000, P400, P400, & P40. Design Load 20 Lbs (.5 kn) Material: 4 gage (.9). Material: 4 gage (.9). "" Weight/C In mm Lbs kg P255 9 6 4.3 44 20.0 P256 8 22.2 44 20.0 P25 3 32 0.3 44 20.0 "" Weight/C In mm Lbs kg P2855 9 6 4.3 32 4.5 P2856 8 22.2 32 4.5 P285 3 32 0.3 32 4.5 54
ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P3922 thru P3926 Back Clevis SPLICE FITTINGS P2869 4 (.9) Gage Threaded Plate Nut 6 3 4" (.5) 4" X 5 8" Flat Head Machine Screws and 4 Hole Splice Plate Nut Included Use Back Plate ssembly "" Clevis With Weight/C Clevis Nut Number Number Channel In mm Number Number Lbs kg P000 P3922 P00 5 8 4.3 P23 P25 P2869 00 45.4 P2000 P3923 P3000 3 8 34.9 P33 P25 P2869 9 44.0 P3924 P4000 3 6 20.6 P53 P25 P2869 80 36.3 P3925 P5500 5 8 4.3 P23 P55 P2869 03 46. Material: 6 gage (.6). P3926 P5000 5 8 4.3 P23 P50 P2869 06 48. P2534-50 P2534-5 CONDUIT SWING FITTING 2" (50.8) P2534-50 For 2" Rigid Conduit P2534-5 For 3 4" Rigid Conduit 4" X 3 4" Slotted Hex Head Screws and Nuts Included 2 Holes 9 32" (.) 3 6" (4.8) 2" (50.8) Bushing Not Included 4 3 6" (22.2) 2" (50.8) Ground Wire 5 (.08π) 5 (.08π) Design Load 300 Lbs (.3 kn) Conduit hanger fittings allow a free swivel of 5 in one direction. Fitting may be mounted to the slot side of the Unistrut channel or to the back. Wt/C 96 Lbs (43.5 kg) 55
ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P2535 8" (22.2) Dia. CONDUIT HNGER CONNECTION FOR 2" CONDUIT 4" X 5 8" Flat Head Machine Screws and P306-420 Nuts Included P2536 3 32" (2.8) Dia. CONDUIT HNGER CONNECTION FOR 3 4" CONDUIT 4" X 5 8" Flat Head Machine Screws and P306-420 Nuts Included 4" (0.6) Design Load 400 Lbs (.8 kn) 5 8" (4.3) 5 8" (30.2) Design Load 200 Lbs (.9 kn) Material: 2 gage (2.). Wt/C 28 Lbs (2. kg) Material: 6 gage (.5) Wt/C 36 Lbs (6.3 kg) P2522 OUTLET BOX CONNECTION P352-50 5 6" (49.2) 3 6" 3 6" (30.2) (30.2) 5 6" (49.2) 4" X 5 8" Flat Head Machine Screws and P306-420 Nuts Included P3000 4" X 5 8" Flat Head Machine Screw and P306-420 Nut Included 2 4" (5.2) END CONNECTORS FOR 2" CONDUIT 8" (22.2) Dia. 6 4" (58.8) 3 Knockouts 8" (22.2) Dia. Wt/C 35 Lbs (5.9 kg) Material: 2 gage (2.). Wt/C 2 Lbs (2.2 kg) P252-50 P252-5 4" X 5 8" Flat Head Machine Screw and P306-420 Nut Included Material: 2 gage (2.) END CONNECTORS FOR 2" & 3 4" CONDUIT 2 6" (52.4) For Unistrut channels P000, P00, & P2000. P552-50 P552-5 4" X 5 8" Flat Head Machine Screw and P306-420 Nut Included P5500 Material: 2 gage (2.). END CONNECTORS FOR 2" & 3 4" CONDUIT 3 8" (34.9) Conduit Size Weight/C In Lbs kg P252-50 2 2 2.2 P252-5 3 4 26.8 Conduit Size Weight/C In Lbs kg P552-50 2 2 2.2 P552-5 3 4 26.8 56
ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P502-50 P502-5 END CONNECTOR FOR 2" & 3 4" CONDUIT P252-00 END CONNECTOR FOR " CONDUIT P5000 4" X 5 8" Flat Head Machine Screw and P306-420 Nut Included 5 8" (4.3) 4" X 5 8" Flat Head Machine Screw and P306-420 Nut Included P000 Tapped for " Conduit Thread 2 6" (52.4) Material: 2 gage (2.). Conduit Size Weight/C In Lbs kg P502-50 2 3 4. P502-5 3 4 30 3.6 Material: 2 gage (2.). Wt/C 24 Lbs (0.9 kg) P502-00 END CONNECTOR FOR " CONDUIT P552-00 END CONNECTOR FOR " CONDUIT Tapped for " Conduit Thread Tapped for " Conduit Thread P5000 P5500 4" X 5 8" Flat Head Machine Screw and P306-420 Nut Included 5 8" (4.3) 4" X 5 8" Flat Head Machine Screw and P306-420 Nut Included 5 8" (4.3) Material: 2 gage (2.). Material: 2 gage (2.). Wt/C 28 Lbs (2. kg) Wt/C 24 Lbs (0.9 kg) P80 W thru P5580 W WIREWY END CPS Material:.05" (.9) Use Weight/C With Lbs kg P80 W P00 2 5.4 P280 W P000 5.0 P2280 W P2000 5.0 P3280 W P3000 5 6.8 P4280 W P4000 5 2.3 P5280 W P5000 22 0.0 P5580 W P5500 8 8.2 5
ELECTRICL CCESSORIES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P254 SPCER CLEVIS 8" DI. (22.2) 8" (3.2) UNISTRUT Channel P254 2 32" (42.) 2" (50.8) 4" (0.6) 2" (50.8) Flourescent Fixture P2540 Wiring Stud Nut Material: 2 gage (2.). Wt/C 24 Lbs (0.9 kg) P2540 P2540 WIRING STUD NUT P36-25 FIXTURE STUD NUT 2" merican Standard Pipe Thread 4" x 20 Thd. 3 6" (30.2) Material: Sintered metal. Design Load 320 Lbs (.4 kn) "" Weight/C In mm Lbs kg P2552 P2540 8 28.6 0 4.5 P2540 5 8 5.9 8 3.6 Wt/C Lbs (5.0 kg) POLYPROPYLENE WIRE RETINER 2" (38.) 2" (38.) Retainer may be easily pushed into channel to support wires until closure strip is installed. Wt/C.30 Lbs (. kg) 58
JUNCTION BOXES FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P280 JUNCTION BOX P28 JUNCTION BOX * See note below. Wt/C 35 Lbs (6.2 kg) * See note below. Wt/C 55 Lbs (0.3 kg) P282 JUNCTION BOX P283 JUNCTION BOX * See note below. Wt/C 55 Lbs (0.3 kg) * See note below. Wt/C 5 Lbs (9.4 kg) P284 JUNCTION BOX * ll Junction Boxes illustrated on this page are: UL listed, CS approved. Junction boxes are for P000, P00 or P2000 channels. ll channel entries in box are 8" (28.6) diameter finished holes with no bushing needed. ll knockouts are 8" (22.2) diameter. 4" x 5 8" flat head machine screws and P306-420 included. * See note below. Wt/C 95 Lbs (88.5 kg) 59
IN-CHNNEL JOINERS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL P2900 P290 P000 Jam screws included. P000 Jam screws included. Material: Cast aluminum. P2902 Wt/C 20 Lbs (9. kg) Material: Cast aluminum. P2903 Wt/C 35 Lbs (5.9 kg) Jam screws included. P000 Jam screws included. P000 Material: Cast aluminum. Wt/C 2 Lbs (2.2 kg) Material: Cast aluminum. Wt/C 45 Lbs (20.4 kg) 60
SWIVEL HNGERS FOR 5 8" (4 MM) WIDTH SERIES CHNNEL M203 M2050 SWIVEL HNGERS M23 M250 SWIVEL HNGERS 3 8" (9.5) DI. B 3 8" (9.5) DI. B " (24.5) Part "B" Weight/C Number "" In mm Lbs kg M203 3 8" - 6 2 3 32" 6.5 23 0.4 M2050 2" - 3 2 3 4" 69.9 32 4.5 Part "B" Weight/C Number "" In mm Lbs kg M23 3 8" - 6 2 29 32" 6.5 2 2.2 M250 2" - 3 2 3 4" 69.9 45 20.4 M2250 SWIVEL HNGER M2350 SWIVEL HNGER 3 8" (9.5) DI. 3 4" (44.5) 3 8" (9.5) DI. 3 4" (44.5) 2" - 3 THD. " (24.5) 2" - 3 THD. Wt/C 8 Lbs (8.2 kg) Wt/C 20 Lbs (9. kg) 6
CBLE ENTRNCE TUBING P6F Slot Size 3 4" (9.) X 8" (22.2) 3 4" (44.5) 2 32" (5.6) 23 32" (43.) Slot Size 32" (3.5) X 8" (22.2) Slot spacing 4" (3.8) on center. 2 32" (5.6) P2H Slot Size 3 4" (9.) X 8" (22.2) 2 3 6" (55.6) 2 32" (5.6) 2 5 32" (54.8) Slot Size 32" (3.5) X 8" (22.2) Slot spacing 4" (3.8) on center. 2 32" (5.6) BEM LOD* LOD (Lbs) 4000 3500 3000 2500 2000 500 000 500 P6F P2H 0 24 36 48 60 2 84 96 08 20 44 68 * Maximum allowable uniform load. SPN (In) Channel Weight llowable Moment Material Thickness Lbs/Ft kg/m In-Lb N m In mm 0' 20' PL GR HG PG SS L P6F.8 2.6 4800 540.05 2. P2H 2.9 4.4 30 280.35 3.4 Standard Lengths Finishes Other Materials 62
CBLE ENTRNCE TUBING DESIGN LOD DT Beam Data Column Data Span Channel Max. llowable Uniform Load Deflection at Uniform Load Uniform Load at Deflection Span/240 Max. Column Load pplied at C.G.* Max. Design Load pplied at Column Face* In mm Lbs kn In mm Lbs kn Lbs kn Lbs kn 24 60 36 94 48 29 60 524 2 829 84 234 96 2438 08 243 20 3048 44 3658 68 426 P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H P6F P2H 600. 0.06 2 600. 9600 42. 3300 4. 390 6.9 0.05 390 6.9 00 8. 6200 2.6 00 4.8 0.3 3 00 4.8 9000 40.0 300 3.8 2530.3 0. 3 2530.3 6900 5.2 6000 26. 800 3.6 0.23 6 690 3. 8300 36.9 2900 2.9 900 8.5 0.9 5 900 8.5 6000.2 500 25.4 640 2.8 0.36 9 440 2.0 500 33.4 200 2.0 520 6.8 0.30 8 280 5. 5000 66. 5400 24.0 530 2.4 0.52 3 30.4 6600 29.4 2400 0. 260 5.6 0.42 890 4.0 3900 6.8 500 22. 460 2.0 0. 8 220.0 5600 24.9 2200 9.8 080 4.8 0.58 5 660 2.9 2600 56.0 400 20.9 400.8 0.93 24 0 0.8 4500 20.0 900 8.5 950 4.2 0.6 9 500 2.2 300 50.3 4300 9. 350.6.8 30 40 0.6 3600 6.0 600. 840 3. 0.95 24 400.8 9900 44.0 3900.3 320.4.45 3 0 0.5 2900 2.9 400 6.2 60 3.4.8 30 320.4 8300 36.9 3500 5.6 20.2 2.09 53 80 0.4 2000 8.9 00 4.9 630 2.8.0 43 220.0 5800 25.8 2800 2.5 230.0 2.85 2 60 0.3 ** ** ** ** 540 2.4 2.3 59 60 0. 4230 8.8 2300 0.2 *K = 0.80 **KL r > 200 Notes:. bove loads include the weight of the member. This weight must be deducted to arrive at the net allowable load the beam will support. 2. Long span beams should be supported in such a manner as to prevent rotation and twist. 3. llowable uniformly distributed loads are listed for various simple spans, that is, a beam on two supports. If load is concentrated at the center of the span, multiply load from the table by 0.5 and corresponding deflection by 0.8. ELEMENTS OF SECTION Channel reas of xis - xis 2-2 Section I S r I S r In 2 cm 2 In 4 cm 4 In 3 cm 3 In cm In 4 cm 4 In 3 cm 3 In cm P6F.46 2.68.68.0.92 3..650..20 8..240 3.9.25.8 P2H.49 4.83.490 20.4.455.5.820 2..590 24.6.540 8.8.900 2.3 I - Moment of Inertia S - Section Modulus r - Radius of Gyration 63
CBLE ENTRNCE FITTINGS P2820 P2940 CHNNEL/TUBE CONNECTORS P2822 P2932 SPLICE FITTINGS 5 3 8" (36.5) 3 3 4" (95.3) 5 8" (4.3) Splice Fitting ssembly Secured to Flat Side with Hardware Provided Use Either Threaded Hole 9 6" (4.3) Dia. Holes 3" (6.2) 6" (.) Dia. Holes Splicing should occur within the top one quarter of column height. Use Weight/C With Lbs kg P2820 P6F 6 52.6 P2940 P2H 48 6. Use Weight/C With Lbs kg P2822 P6F 9 44.0 P2932 P2H 22 55.3 P2823 90 RCK FITTING P282 LOCKING CLIP P4000 P282 Locking Clip 5" (2.0) Cable Hook supplied by others. Exclusive Cable Hook Locking Clip prevents Cable Hook removal. Wt/C 66 Lbs (29.9 kg) Wt/C 3 Lbs (.4 kg) 64
CBLE ENTRNCE BRCKETS P2920 thru P2924 CBLE BRCKETS 3 6" (4.8) x 3 4" (9.) Slots 2 3 4" (69.9) on Center 5 8" (4.3) B L Use with P6F or P2H. Material: 2 gage steel. "L" "" "B" Weight/C Uniform Design Load In mm In mm In mm Lbs kg Lbs kn P2920 5 2 39. 3 2 88.9 8 22.2 90 40.8 500 2.2 P292 8 4 209.6 3 2 88.9 8 22.2 20 54.4 325.4 P2922 29.4 3 2 88.9 5 8 4.3 300 36. 25.2 P2923 3 3 4 349.3 3 2 88.9 5 8 4.3 340 54.2 220.0 P2924 9 4 489.0 3 2 88.9 5 8 4.3 430 95.0 60 0. Safety factor of 3. P2928 P2929 P2930 5 8" (4.3) CBLE BRCKETS B L Use with P6F or P2H. Material: 2 gage steel. "L" "" "B" Weight/C Uniform Design Load In mm In mm In mm Lbs kg Lbs kn P2928 6 52.4 3 2 88.9 8 22.2 92 4. 500 2.2 P2929 2 304.8 3 2 88.9 5 8 4.3 320 45. 250. P2930 8 45.2 3 2 88.9 5 8 4.3 420 90.5 0 0.8 Safety factor of 3. 65